• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Electromagnetic control of the instability in the liquid metal flow over a backward-facing step

    2022-12-28 09:54:02YaDongHuang黃亞冬JiaWeiFu付佳維andLongMiaoChen陳龍淼
    Chinese Physics B 2022年12期

    Ya-Dong Huang(黃亞冬) Jia-Wei Fu(付佳維) and Long-Miao Chen(陳龍淼)

    1Jiangsu University,Zhenjiang 212013,China

    2Nanjing University of Science and Technology,Nanjing 210094,China

    Keywords: electromagnetic actuator,backward-facing step flow,flow instability,flow control

    1. Introduction

    The liquid metal is widely utilized in the thermal management and energy storage due to its high thermal conductivity,[1,2]such as heat exchange in nuclear engineering,[3]cooling of high-power-density microdevices,[4]and harvesting the low grade heat to generate electricity.[5]Also, the liquid metal is attractive in the mechanical to electrical energy conversion via magnetohydrodynamics (MHD) generator[6]due to its excellent electoral conductivity. In the heat transfer flow system, both the heat transfer efficiency and the flow instability are commonly taken into consideration. Usually, a backward-facing step (BFS) is designed in the heat exchanger to enhance the heat transfer via flow separation and reattachment.[7,8]The BFS flow often contains two separation bubbles and the flow structures are mainly dependent on the Reynolds numbers based on the maximum inlet velocity and the hight of the step.[9]Perturbations could gain energy amplification when flowing through the separation bubbles owing to the Kelvin–Helmholtz (KH) instability,[10]Taylor–G¨ortler instability,[11]centrifugal instability[12]and other instability mechanisms,[13,14]and the amplification may make a great influence on the heat transfer efficiency.[15,16]Thereby, researchers adopt active[17,18]and passive[19,20]controls of the BFS flow to achieve the desired heat transfer efficiency. However, the perturbation amplification may aggravate the flow system instability, which is unfavourable for the liquid metal transport. It is an available strategy that the control method could regulate the perturbation energy in the liquid metal BFS flow.

    As a classical law of physics, the interactions between the electrical current and the magnetic field in the liquid metal could generate the Lorentz force to control the flow[21,22]and transport the liquid metal.[23]In former studies, the Lorentz force had made great contributions to drag reduction, transition suppression and so forth in the flow control. The Lorentz force is generated by the electromagnetic field which could be excited via the electromagnetic actuator consisting of alternatively arranged electrodes and magnetic poles, and having two types: tile and stripe.[24]The tile-type electromagnetic actuator (TEA) and stripe-type electromagnetic actuator (SEA) could engender the wall-normal and wall-parallel Lorentz force respectively. It was found the streamwise (or wall-parallel) Lorentz force applied in the separation bubble could reduce the bubble size thus modifying the growth rates of the perturbation energy.[25]Moreover, the perturbation energy in the BFS flow also could be adjusted by the linear control model with a feed-forward controller.[26,27]Although research has proposed several control methods to adjust the instability in the BFS flow, the flexibility for different control strategies needs further discussion. Hence,the control effects of different control strategies on the instability in the liquid metal BFS flow would be investigated in this paper.

    2. Methodology

    The incompressible liquid metal flow controlled via the Lorentz force is modelled by the Navier–Stokes equation:

    while the linear evolution of perturbations can be predicted by solving the following linear perturbation equation:

    containing the external forcing term???and the Lorentz force?qq.?qand??are the spatial structures of the body force, andqand?are time-dependent variables representing the noise source and control input respectively.

    According to the achievements in Refs. [25,26], three control strategies: the base flow control (BFC), linear model control (LMC) and their combination (combined model control,CMC)are considered to adjust the flow instability in this paper. The control model is shown in Fig.1. The step height ishwhich is also the characteristic length. The height of the expansion channel is 2h. To be convenient for description and calculation, the origin of the Cartesian coordinate locates on the step corner. As the Reynolds number in current research is 500,the uncontrolled steady flow contains the primary separation bubble (PSB) on the lower wall and the secondary separation bubble(SSB)on the upper wall.x1is the reattachment point of PSB, andx2,x3are the separation and reattachment points of SSB.

    It could be observed that three electromagnetic actuators(A1,A2,and A3)and two sensors(S1and S2)exist in the flow system. According to our previous investigation,[25]SEAs A1and A2could be installed inside the separation bubbles in BFC.TEA A3is applied to LMC which also has the sensors S1and S2. The sensor S1is placed near the noise source to measure the incoming disturbance because?is very difficult to come by in physical experiments. The sensor S2is employed to measure the outputs.

    Fig.1. Control model.

    In LMC and CMC, the linear control model could be established based on the numerical data of Eq. (2) via the Galerkin projection. As the BFS flow usually acts as a noise amplifier, the Galerkin-based method has many limitation in accurately capturing the transfer behavior from the input to the output.Some researchers adopted the auto-regressive movingaverage exogenous (ARMAX) model[28]to perform the system identification. For simplicity, researchers usually formulate the state-space system in a discrete-time format.The mapping of the inputss,qfrom S1,A3,and the outputmfrom S2could be described by the following model:

    wheremis the output and term 1 is the auto-aggressive part.qandsare the inputs and terms 2,3 represent the exogenous part.eis the noise and term 4 means the moving average part.The coefficientsak,bk, andckcould be found via regression.nais the previous outputs on which the current output depend on.ndqandndsrepresent the numbers of the passed inputs due to the delaying effects of the input on the output.nbqandnbsmean the numbers of the previous inputs on which the current output depends.ncis the number of time-colored noise.Readers could know more about the detailed meaning of the parameters in Eq.(5)in Ref.[26].

    In BFC and CMC,the sphere of action is set as 0

    3. Mesh and validation

    All equations are solved with a high accuracy spectralelement method (SEM)[32]in the domain shown in Fig. 2.The spatial domain is split into 2039 quadrilateral finite elements, in which both the geometry and solution variables employ equal-order tensor-product Lagrange polynomial expansions. The flow separates near the corner of the step and the circumfluence in the separation bubbles generates near the upper and lower walls, so the grids there are refined. Gauss–Lobatto Legendre polynomials are adopted as a basis for the numerical solution. The time-stepping method based on the backwards-time differencing[33]is taken to perform the time integration. The Krylov subspace method and the Arnoldi decomposition method are employed to solve the eigenvalue in the optimal transient growth analysis.

    Fig.2. Calculation domain and mesh.

    Fig. 3. Separation bubble length varying with the Reynolds numbers from references and current results.

    For the base flow solution, a Dirichlet condition is set atΓ∞(U=4y ?4y2,V=0), and a Neumann condition is set atΓo(?nU=0,?nV=0). A no-slip Dirichlet condition is set atΓb(U=0,V=0). A high-order Neumann condition for the normal component along the boundary calculated from Eq.(1)is set for the pressure at all boundaries exceptΓowhere the pressure is set to be zero. For the linear stability analysis,the boundary conditions are similar with those in the base flow solution, but the perturbation velocityu′is set to be zero atΓ∞andΓb. For the optimal transient growth analysis, perturbations at all boundaries are set to be zero. Besides, readers cloud learn more about the detailed solution procedure of the eigenproblem in the optimal transient growth analysis via the achievements of Barkleyet al.[33]In all calculations,the timestep is set as 0.001 with the second-order time integration and eighth-order polynomials. The lengths of the primary and secondary separation bubblesxsas a function of Reynolds number are shown in Fig.3. Both lengths increase with the Reynolds number,and our results are consistent with those in the reference.

    4. Results and discussion

    4.1. Effects of BFC

    The maximum amplification ratesGmof the initial Gaussian perturbation?as well as the corresponding steady base flow with BFC are reported in Fig. 4.N1andN2represent the control numbers of the streamwise Lorentz force from A1and A2respectively.N1andN2constitute the coordinate system of control numbers. It is worth mentioning that the inlet noise source in BFC is also the noise source???in LMC and CMC.In BFC,we mainly discuss the control effects based on the single initial wall-normalwise perturbation. In order to facilitate our research,it is assumed that the noise source obeys the Gaussian distribution,which could be written as

    whereAis the amplitude of perturbations,(x0,y0)is the center of perturbations andσx,σyare the radiation radii of perturbations. The parameter in Eq. (6) are (x0,y0)=(?0.5,0.25),(σx,σy)=(0.1,0.1), andA=4.0, and the perturbation variable?could be expressed via the Dirac function.

    It could be observed thatGmcould achieve the peak value at (0.1,0.2) while the minimal one at (0.15,0) according to Fig. 4(a). Meanwhile, the distributions ofGmalso illustrate that the streamwise Lorentz force only acting on SSB could reduce the maximum amplification rate, while acting on both PSB and SSB could achieve the opposite effects. In other words, it could stabilize the liquid metal flow via fixing SEA only in SSB, or destabilize the flow by setting SEA in both separation bubbles. Figure 4(b)demonstrates the steady base flows of which the maximum amplification rates are marked in Fig.4(a). Cases A–E correspond to the control numbers at(N1,N2)=(0,0), (0.15,0), (0.3,0), (0.3,0.2), and (0.1,0.2)respectively.The contour in Fig.4(b)is colored by the streamwise velocity. The solid blue lines represent the isolines ofU=0,and the liquid metal inside the isoline contains a backflow. Moreover,the isolines also present the scales of the separation bubbles. We can clearly see the PSB and SSB for the no-control (NC) case (case A). For case B, there only exists the PSB but its length is larger than that for case A because the streamwise Lorentz force could reduce the magnitude of the backflow velocity of the separation bubble, and then the bubble dwindles gradually. The decrease of SSB size may flatten the concave streamline near SSB, and then the separation streamline near PSB may lift up. Once the control strength from A1increases(case C),the length of PSB might take a growth. If the electromagnetic actuator A2is turned on, the PSB could be divided into two smaller bubbles (case D). However, the scale of PSB in the wall-normalwise direction is much larger than that of SSB,so effects of the streamwise Lorentz force on SSB size are more remarkable. It could be observed that the scale of the downstream divided bubble might be reduced once the control strength from A2decreases by comparing cases D and E.It is obvious that the amplification rate of the initial Gaussian perturbation energy is minimal for case B and maximum for case E.

    Fig. 4. The maximum growth rates of the initial Gaussian perturbation for different control numbers and corresponding base flows. (a)The maximum growth rates. (b)The corresponding base flow.

    Figure 5 shows the energy derivative varying with the time calculated from the Reynolds–Orr equation.[34]The energy derivative is nondimensionalized byE0/t0whereE0is the initial perturbation energy andt0is the unit time. Actually,dE/dthas a positive correlation to the rates of the curves in Fig. 4, andG(t)in Fig.4 achieves the peak value at the time corresponding to dE/dt=0 in Fig.5.

    Fig.5. Growth rate of perturbation energy varying with the evolution time.

    Figure 6(a) shows the optimal energy growth of perturbations over a given time intervalτ. It is the fact that the peak amplification rate of the perturbation energy in the optimal transient growth is much larger than that of the single initial Gaussian perturbation. We know that the optimal initial perturbations in the optimal transient growth are different and they are dependent on the time interval. It could be found that the optimal amplification rate of the two-dimensional perturbation always increases with the evolution interval and reaches to the peak value at aboutτ=60,and then decays.Figure 6(b)presents the optimal initial perturbations of which the optimal amplification rates atτ=60 are shown in Fig.6(a). The perturbation energies are normalized, and the contours are colored with the perturbation vorticity of the level from?0.1 to 0.1. The patterns of the optimal initial perturbations resemble the KH vortices,and always distribute along the separation line.The typical spatial distribution like the KH vortices in the optimal initial perturbation could diminish the effects of distortion and dissipation from the mean strain field because each initial perturbation could evolve into the KH-like vortices.

    Figure 7 illustrate the optimal amplification rates of the three-dimensional perturbations for the evolution interval ofτ=60 and corresponding optimal initial perturbations. The optimal amplification rate of the three-dimensional perturbation energy slightly increases at small spanwise wavenumbers,and then decreases. The maximum value approximately appears atβ=0.5. The magnitude of the optimal amplification rate in case E is still the maximum one while that in case B is always the minimal one for the same spanwise wavenumber. This phenomenon indicates that BFC assurely increase or decrease the amplification rate of the perturbation energy in the liquid metal BFS flow. The three-dimensional optimal initial perturbation is visualized via the spanwise velocity. The distributions of the three-dimensional optimal initial perturbations are different from the two-dimensional ones. Besides the step corner and the outlines of the separation bubbles, most spanwise perturbations locate near the step. This distribution features are similar with those in Ref.[10].

    Fig.6. The optimal amplification rate of two-dimensional perturbations and corresponding initial perturbations. (a)Optimal amplification rates varying with the evolution intervals;(b)corresponding initial perturbations.

    Fig.7. The optimal amplification rate of three-dimensional perturbations and corresponding initial perturbations. (a) Optimal amplification rates varying with the spanwise wave numbers; (b) corresponding initial perturbations.

    4.2. System identification in LMC and CMC

    The above discussions have indicated that BFC could capably modify the perturbation energy in the liquid metal BFS flow. However, the flow system needs to keep laminar sometimes since the liquid metal contains a high heat transfer efficiency. The perturbation energy also could be amplified in BFC,thereby LMC and CMC are adopted to suppress the amplification of the perturbation energy in our control strategies.Certainly, CMC also could be employed to increase the perturbation energy because it contains BFC.It is noteworthy that LMC and CMC are performed based on cases A and B respectively. For contrast,the spatial distribution of the noise source?in LMC and CMC is same with that in BFC,and the Lorentz force from the actuator A3also has the Gaussian distributions,and the parameters of?qfrom A3are(x0,y0)=(?0.05,0.01),(σx,σy)=(0.01,0.1), andA=4.0. Meanwhile, the perturbation variable?could be expressed as the Gaussian white noise with the standard deviation of 0.01 and the control inputqcould be written as the binary random function with the maximum amplitude of 0.0054 like Ref.[10].

    Usually, referred to Ref. [31], the sensor S1is located downstream the noise source but upstream the actuator A3,and the sensor S2is placed near the reattachment point of PSB,thereby the signals of input and output in LMC and CMC are defined as follows:

    Figure 8(a) shows the amplitude-frequency characteristics of the original input and output signals in CMC.In order to reflect the amplification features of the flow system on the noise,the signalssandmhere are obtained without the control input signalq. It can be seen that the amplitude of all signals attenuates rapidly when the frequency is greater than 1,so the low-pass filter could be adopted to extract the main parts of signals. The principle of the low-pass filtering is keeping the low-frequency amplitude-frequency characteristics as well as the amplitude of the original input and output signals. The transfer function of the low-pass filtering here is referred to Ref.[31]and could be written as

    withη=0.8 andωc=2. Figure 8(b) shows the amplitudefrequency characteristics of the low-pass filtered signal. It can be seen that the filtered signals has the similar amplitudefrequency characteristics with the original signals. In addition, the amplitude–frequency characteristics of the original and low-pass filtered signals with the same transfer function in LMC also resemble those in Fig.8.

    Fig.8. Amplitude–frequency characteristics of original and filtered signals.(a)Original signal;(b)filtered signal.

    Although the amount of data in the control model needs to be reduced, it is still necessary to ensure that the sampling data is sufficient. As mentioned above,the time step is 0.001 in all calculations,so the sampling period is set to 0.1.Figure 9 shows the auto-correlation and cross-correlation functions between the sampling signals. Observing the auto-correlation function curve of the output signalm, it could be seen that the curve reaches the minimum value at the time oft=4.1 andt=6.0 for LMC and CMC respectively. That is to say,there might be a duration of 4.1 and 6.0 for the previous outputs having an impact on the subsequent outputs. Hence, the value ofnain the ARMAX models for LMC and CMC are 4.1/0.1=41 and 6.0/0.1=60 respectively. In addition, the cross-correlation function curves ofsandm,q,andmbegin to fluctuate intensely att=11.5 for LMC andt=22.5 for CMC.This phenomenon demonstrates the response delay time of the output to a single input is 11.5 and 22.5 for LMC and CMC respectively,so the values ofndsandndqin the ARMAX model should be around 115 for LMC and 225 for CMC. Once the cross-correlation function curves(green one)ofqandmtake an intense fluctuation,the time intervals between the first wave valley and wave peak are 2.9 and 4.2 for LMC and CMC respectively. This appearance indicates that the time interval of the input signal affecting the current output is 2.9 for LMC and 4.2 for CMC. Thereby, the value ofnbqin the ARMAX model is around 29 for LMC and 42 for CMC.In fact,as S1is close to A3, the value ofnbqis similar with that ofnbsin the ARMAX model.

    Fig.9.Auto-correlation and cross-correlation characteristics of the measured variables. (a)LMC;(b)CMC.

    The parameters in the ARMAX models for LMC and CMC are shown in Table 1. The primary sharp of signals predicted by the ARMAX model are mostly dependent on these parameters.na,nbq,nbs,ndq, andndsare usually determined fristly and thenncis adjusted to improve the goodness of fti between the predicted and sampling signals. The goodness of fti could be expressed as

    wherempis the signal predicted by the ARMAX model andmris the sampling signal.Figure 10 shows the predicted and sampling signals. It could be observed that the output signals from the ARMAX model coincide with the sampling signals. The goodness of the fit is 91.2% and 86.4% for LMC and CMC respectively.

    Table 1. Parameters in the ARMAX model.

    Fig.10. The signals predicted by the ARMAX model(black line)and the sampling signals(red line).(a)Signals in LMC.(b)Signals in CMC.

    Fig.11. The characteristics of impulse response in the ARMAX model.

    Figure 11 shows the impulse response of the output signal to a single input signal in the ARMAX model. As discussed above, the start time of response has been shown in Table 1. For LMC,the amplitude of the response signal tends to 0 whent>35, while it still has slight fluctuations whent>65 and tends to 0 untilt>110 for CMC.It could be found that the two response signals for each control strategy fluctuate in opposite directions. The time for the output response to the noise signal achieving the peak value slightly lags behind the response to the control input signal,because the actuator A3is downstream the sensor S1. Comparing the maximum amplitudes of the response signals, we could observe that the peak amplitude of the response to the noise signal is greater than that of the response to the control input signal both for LMC and CMC, because the spatial distribution area of the noise source signal is larger than that of the control input signal.

    4.3. Closed-loop control in LMC and CMC

    Once the parameters of the ARMAX model are achieved,the transfer functions ofq →mands →mare identified. The coefficients in the transfer function are referred as the Markov parameters, which represent the impulse response of the system. If we want to know the future control signal according to the measured signal,the corresponding compensator needs to be designed to build a complete closed-loop system. The system without compensator is called an open-loop system. The relationship between the future output signalMT,the known(or measured) noise signalSg, the control signalQgand the future unknown control signalQfcould be constructed via the Markov matricesZs,Zq,andLqin any sampling time periodT. The expression could be written as

    They could be achieved from the corresponding impulse responses in the ARMAX model. In Fig. 11, the impulse response of the output signal to the two input signals tends to 0 whent>35 for LMC andt>110 for CMC,so the time periodTshould be greater than 400 for LMC and 1100 for CMC in Eq.(10). If we want to get the control input signalQfin the next period,we must know the future output signalMTwhich is also the expected output signal. The control targets of LMC and CMC are completely suppressing the noise,that is to say‖MT‖22=0,thusQfcould be written as

    HereL+qis the pseudo-inverse of matrixLqbecause matrixLqdoes not have an inverse matrix. Equation (12) defines a linear dynamic system where the input is the noise and control signal in the previous period,and the output is the control signal in the next period, so the compensator is also called a feed-forward controller. In the pseudo-inverse solution, the tolerance value needs to be set. The principle of tolerance setting is that the reciprocal of all singular values of the matrixLqare greater than the tolerance value. However, the amplitude of the impulse response of the output signal to the input noise signal in the compensator increases as the tolerance decreases.In other words,growth of the amplitude of the control signal might improve the control cost. If the tolerance value is not considered,the performance of the compensator could be better for a longer time period. Meanwhile,it could take more time to completely suppress the noise. The tolerance value is set to 0.15 for both LMC and CMC,and the time period is set tot=100 andt=180 for LMC and CMC respectively.

    Figure 12(a) shows the impulse response of the output signal to the noise signal for the close-loop and open-loop systems. The dashed line represents the open-loop system, and the solid line represents the closed-loop system. Compared with the output signal without the controller,the response amplitude of the output signal decreases significantly after applying the controller, and tends to 0. Figure 12(b) shows the impulse response of the output signal with the controller to the noise signal, which is also the required control input signal for the closed-loop system. It can be seen that the control input signal decreases rapidly from the maximum value at the beginning, and then exhibits a damped oscillation and finally decays to 0.

    Fig. 12. The impulse response of output to input in LMC and CMC.(a)Impulse response of m to s;(b)impulse response of q to s.

    Fig.13.Outputs of the open-loop system and close-loop system in LMC and CMC.(a)Open-loop system;(b)close-loop system.

    Fig.14. Control inputs of the close-loop system.

    Figure 13 shows the output signals obtained in the openloop and close-loop systems. The signals in Fig. 13(a) from the open-loop system are the original filtered signals. The amplitude of the signal for LMC is less than that for CMC because the the location of S2for CMC is downstream that for LMC.Although the peak amplification rate for case B is much less that for case A, the measurements in local regions still grow along the flow direction. It can be seen that the pulsation amplitude of the output signal is reduced by 86.5%and 95.3%for LMC and CMC respectively after applying the controller.

    4.4. Comparison

    Figure 15 shows the perturbation energy?=∫?0.5(u′2+v′2)dVof the entire liquid metal flow system varying with the evolution time for different control strategies. The black line, red line, green line and blue line represent the perturbation energy for NC, BFC, LMC and CMC respectively. All controls are turned on att= 2000. We could find that the magnitude of the perturbation energy in the liquid metal flow could be reduced once the electromagnetic actuators are turned on. The average value of the perturbation energy in the time period oft=2500–3500 is reduced by 54.9%, 97.4%, and 99.8% for BFC, LMC and CMC respectively. We could observe the profiles of NC and LMC have some overlap parts at beginning, and this phenomenon also exists for BFC and CMC.As discussed above,there exists a time interval for the response of the output signal to the input signal. We know the control targets of LMC and CMC are completely suppressing the noise,but the perturbation energy could not be suppressed completely. However, the magnitude of the perturbation energy could be reduced by 2 orders in LMC, and 3 orders in CMC.The inherent properties of amplification are responsible for this phenomenon. The sensor S2just could measure the local perturbation energy,and perturbations in other parts also be amplified. BFC could change the amplification features of the liquid metal BFS flow,and the linear control model could reduce the magnitude of the perturbation energy of whole liquid metal BFS flow. At least, CMC could achieve a better suppression of the perturbation energy compared with BFC and LMC.Since CMC is the combination of BFC and LMC,we could adjust the instability in the liquid metal BFS flow by turning on or turning off some actuators.

    Fig.15. Variations of the perturbation energy of the whole system for different control strategies.

    5. Conclusion

    To summarize, TEA and SEA could be applied to adjust the perturbation energy in the liquid metal BFS flow. Setting SEA in both PSB and SSB could amplify the magnitude of the perturbation energy, while combination of TEA, SEA (only acting on SSB)and two sensors could suppress the amplification of the perturbation energy. These results manifest that the electromagnetic actuators have the satisfied regulation effects on the perturbation energy in the liquid metal BFS flow, and the strategy of CMC could be commendably applied to engineering.

    Acknowledgment

    Project supported by the National Natural Science Foundation of China(Grant No.U2141246).

    国产久久久一区二区三区| 有码 亚洲区| 久久人人爽人人爽人人片va | 免费电影在线观看免费观看| 亚洲,欧美精品.| 免费高清视频大片| 国产av不卡久久| 嫩草影院精品99| 欧美zozozo另类| 麻豆国产av国片精品| 精品人妻一区二区三区麻豆 | 国产69精品久久久久777片| 丁香六月欧美| av在线蜜桃| 久久中文看片网| 一夜夜www| aaaaa片日本免费| 欧美一级a爱片免费观看看| 亚洲av美国av| 在线观看午夜福利视频| 国产aⅴ精品一区二区三区波| 国内精品一区二区在线观看| 免费看a级黄色片| 女生性感内裤真人,穿戴方法视频| 高清毛片免费观看视频网站| 99久久成人亚洲精品观看| 两性午夜刺激爽爽歪歪视频在线观看| 午夜影院日韩av| 久久久久久大精品| 99久久精品国产亚洲精品| 精品一区二区三区av网在线观看| 九九在线视频观看精品| 日韩欧美三级三区| 亚洲欧美日韩高清专用| av专区在线播放| 999久久久精品免费观看国产| 色综合亚洲欧美另类图片| 中亚洲国语对白在线视频| 欧美成人免费av一区二区三区| 国产午夜精品论理片| 午夜免费成人在线视频| 免费观看人在逋| 亚洲成a人片在线一区二区| 小蜜桃在线观看免费完整版高清| av中文乱码字幕在线| 丰满乱子伦码专区| 日本黄色片子视频| 757午夜福利合集在线观看| 色在线成人网| 69av精品久久久久久| 蜜桃亚洲精品一区二区三区| 99国产精品一区二区三区| 亚洲乱码一区二区免费版| 国产一区二区三区在线臀色熟女| 国产精品伦人一区二区| 白带黄色成豆腐渣| 久久久久久久久大av| 久久午夜福利片| 久久伊人香网站| 亚洲色图av天堂| 少妇被粗大猛烈的视频| 中国美女看黄片| 色尼玛亚洲综合影院| 免费无遮挡裸体视频| 日韩中字成人| 国产成人影院久久av| 级片在线观看| 国产免费一级a男人的天堂| 亚洲av美国av| x7x7x7水蜜桃| 国产亚洲精品综合一区在线观看| 亚洲国产精品999在线| 一级毛片久久久久久久久女| 国产精品久久电影中文字幕| h日本视频在线播放| 色噜噜av男人的天堂激情| 一区二区三区四区激情视频 | 97超视频在线观看视频| 国产真实乱freesex| 国产精品电影一区二区三区| 精品久久久久久,| 日韩欧美免费精品| 国产久久久一区二区三区| 国产老妇女一区| 香蕉av资源在线| 18美女黄网站色大片免费观看| 国产精品永久免费网站| 亚洲电影在线观看av| 深夜精品福利| 非洲黑人性xxxx精品又粗又长| 9191精品国产免费久久| eeuss影院久久| 久久6这里有精品| 欧美日韩亚洲国产一区二区在线观看| 亚洲av五月六月丁香网| 久久精品夜夜夜夜夜久久蜜豆| 啪啪无遮挡十八禁网站| 丰满人妻熟妇乱又伦精品不卡| 变态另类成人亚洲欧美熟女| 少妇被粗大猛烈的视频| 嫩草影院精品99| 给我免费播放毛片高清在线观看| 国产精品爽爽va在线观看网站| av天堂在线播放| 久久亚洲精品不卡| 色综合站精品国产| 亚洲五月天丁香| 如何舔出高潮| 99久久99久久久精品蜜桃| 成人毛片a级毛片在线播放| 男女下面进入的视频免费午夜| 琪琪午夜伦伦电影理论片6080| 性色avwww在线观看| 三级毛片av免费| 日日夜夜操网爽| 男人的好看免费观看在线视频| 国内毛片毛片毛片毛片毛片| 亚洲av免费高清在线观看| 中文在线观看免费www的网站| av黄色大香蕉| 午夜视频国产福利| 大型黄色视频在线免费观看| 亚州av有码| 国产伦人伦偷精品视频| 99久久精品国产亚洲精品| 小蜜桃在线观看免费完整版高清| 老熟妇仑乱视频hdxx| 88av欧美| 日本 欧美在线| 一卡2卡三卡四卡精品乱码亚洲| 好看av亚洲va欧美ⅴa在| 好男人电影高清在线观看| 国产免费av片在线观看野外av| 九九热线精品视视频播放| 少妇人妻精品综合一区二区 | 欧美性感艳星| a在线观看视频网站| 日韩有码中文字幕| 最近最新中文字幕大全电影3| .国产精品久久| 国产一区二区在线观看日韩| 亚洲一区二区三区不卡视频| 天堂影院成人在线观看| 亚洲va日本ⅴa欧美va伊人久久| 成年女人看的毛片在线观看| 丰满的人妻完整版| 最后的刺客免费高清国语| 别揉我奶头 嗯啊视频| 久久久久久久久久成人| 国产免费一级a男人的天堂| 变态另类丝袜制服| 青草久久国产| 中文字幕免费在线视频6| 国产精品不卡视频一区二区 | av在线天堂中文字幕| 性插视频无遮挡在线免费观看| 99热6这里只有精品| 亚洲国产精品久久男人天堂| 国产精品电影一区二区三区| 久久精品91蜜桃| 国内揄拍国产精品人妻在线| 99在线人妻在线中文字幕| 男女视频在线观看网站免费| 在线看三级毛片| 老师上课跳d突然被开到最大视频 久久午夜综合久久蜜桃 | 亚洲va日本ⅴa欧美va伊人久久| 91久久精品电影网| 国产欧美日韩一区二区三| 国内毛片毛片毛片毛片毛片| a在线观看视频网站| 婷婷丁香在线五月| 日本黄色片子视频| 天堂网av新在线| 国产成+人综合+亚洲专区| 在线天堂最新版资源| 亚洲精品在线观看二区| 我的女老师完整版在线观看| 亚洲内射少妇av| 91在线精品国自产拍蜜月| 久久午夜福利片| 国产精品久久久久久久久免 | 精品一区二区三区视频在线观看免费| 嫩草影视91久久| 美女免费视频网站| 丝袜美腿在线中文| 午夜福利成人在线免费观看| 国内精品一区二区在线观看| 精品久久久久久久久亚洲 | 51国产日韩欧美| 欧美日韩国产亚洲二区| 大型黄色视频在线免费观看| 欧美一区二区亚洲| 热99re8久久精品国产| 人妻丰满熟妇av一区二区三区| 日韩中文字幕欧美一区二区| 五月玫瑰六月丁香| 欧美乱妇无乱码| 十八禁国产超污无遮挡网站| 亚洲精品在线美女| 天堂动漫精品| 男插女下体视频免费在线播放| 美女高潮的动态| 成人精品一区二区免费| 精品国产亚洲在线| 国产主播在线观看一区二区| 亚洲狠狠婷婷综合久久图片| 麻豆国产av国片精品| 天堂网av新在线| 在线天堂最新版资源| 一进一出好大好爽视频| 国产伦人伦偷精品视频| 国产麻豆成人av免费视频| 可以在线观看毛片的网站| 久久精品91蜜桃| 在线免费观看的www视频| 亚洲黑人精品在线| 婷婷丁香在线五月| 成人高潮视频无遮挡免费网站| 人人妻,人人澡人人爽秒播| 长腿黑丝高跟| 午夜精品在线福利| 别揉我奶头 嗯啊视频| 一级黄色大片毛片| av国产免费在线观看| 久久精品综合一区二区三区| 日韩高清综合在线| 最后的刺客免费高清国语| 久久伊人香网站| 小说图片视频综合网站| 国产主播在线观看一区二区| 久久亚洲真实| 久久久国产成人精品二区| 国产成+人综合+亚洲专区| 国产伦精品一区二区三区视频9| 十八禁人妻一区二区| 怎么达到女性高潮| 国产三级中文精品| 69av精品久久久久久| 成人美女网站在线观看视频| 国产爱豆传媒在线观看| 久久久久久大精品| 久久99热6这里只有精品| 色综合婷婷激情| 熟妇人妻久久中文字幕3abv| 亚洲真实伦在线观看| 丰满人妻一区二区三区视频av| 午夜a级毛片| 十八禁网站免费在线| 少妇裸体淫交视频免费看高清| 99riav亚洲国产免费| 国产视频内射| 久久精品国产亚洲av天美| 窝窝影院91人妻| 欧美不卡视频在线免费观看| 身体一侧抽搐| 国产主播在线观看一区二区| 少妇的逼好多水| 69av精品久久久久久| 欧美极品一区二区三区四区| 日日摸夜夜添夜夜添av毛片 | 免费看光身美女| 国产男靠女视频免费网站| 国产亚洲欧美在线一区二区| 性插视频无遮挡在线免费观看| 亚洲欧美精品综合久久99| 特级一级黄色大片| 91av网一区二区| 久久久久九九精品影院| 91在线观看av| 亚洲真实伦在线观看| 我要搜黄色片| 日韩 亚洲 欧美在线| 国产又黄又爽又无遮挡在线| 亚洲精品在线美女| 国产精品免费一区二区三区在线| 久久6这里有精品| 亚洲av不卡在线观看| 国产黄片美女视频| 99久久精品热视频| 精品免费久久久久久久清纯| 真人一进一出gif抽搐免费| 脱女人内裤的视频| 人人妻,人人澡人人爽秒播| 18禁在线播放成人免费| 国模一区二区三区四区视频| 国产成人av教育| 99久久成人亚洲精品观看| 熟妇人妻久久中文字幕3abv| 国产精品影院久久| 听说在线观看完整版免费高清| 两人在一起打扑克的视频| 亚洲中文日韩欧美视频| 免费av不卡在线播放| 欧美又色又爽又黄视频| 黄色女人牲交| 美女xxoo啪啪120秒动态图 | 午夜免费男女啪啪视频观看 | 高清毛片免费观看视频网站| 国产久久久一区二区三区| 黄色一级大片看看| 深夜a级毛片| 两个人视频免费观看高清| www.熟女人妻精品国产| 日本黄大片高清| 99在线人妻在线中文字幕| x7x7x7水蜜桃| 人妻制服诱惑在线中文字幕| 高清日韩中文字幕在线| 18禁裸乳无遮挡免费网站照片| 精品日产1卡2卡| 99久久精品一区二区三区| 中文亚洲av片在线观看爽| 色综合亚洲欧美另类图片| 国产伦人伦偷精品视频| 欧美黄色淫秽网站| 少妇熟女aⅴ在线视频| 免费看a级黄色片| 九九热线精品视视频播放| 国产欧美日韩一区二区精品| 真实男女啪啪啪动态图| av福利片在线观看| 午夜a级毛片| 久久亚洲真实| 日韩大尺度精品在线看网址| 小说图片视频综合网站| 午夜a级毛片| 国产高清有码在线观看视频| 又爽又黄无遮挡网站| 一个人看视频在线观看www免费| 免费看a级黄色片| 亚洲欧美日韩卡通动漫| 99久久成人亚洲精品观看| 不卡一级毛片| 亚洲性夜色夜夜综合| 99久久精品国产亚洲精品| 日本熟妇午夜| 91麻豆精品激情在线观看国产| 欧美色视频一区免费| 淫妇啪啪啪对白视频| 国产精品1区2区在线观看.| 美女免费视频网站| 日本a在线网址| 桃色一区二区三区在线观看| 99热精品在线国产| 成人国产一区最新在线观看| 亚洲精品色激情综合| 桃红色精品国产亚洲av| 日韩欧美国产在线观看| 永久网站在线| 搡女人真爽免费视频火全软件 | 国产成人啪精品午夜网站| 91在线观看av| 欧美一区二区精品小视频在线| 乱人视频在线观看| 午夜福利成人在线免费观看| 亚洲av二区三区四区| 国产不卡一卡二| 国产精品久久久久久人妻精品电影| 欧美成人免费av一区二区三区| 少妇熟女aⅴ在线视频| 精品国产三级普通话版| 嫩草影院入口| 啦啦啦观看免费观看视频高清| 不卡一级毛片| 精品久久国产蜜桃| 最新在线观看一区二区三区| 欧美激情国产日韩精品一区| 日韩欧美三级三区| 国产视频内射| 婷婷精品国产亚洲av| 精品久久久久久久久av| 一卡2卡三卡四卡精品乱码亚洲| 精品一区二区三区视频在线观看免费| 欧美一区二区国产精品久久精品| 97超级碰碰碰精品色视频在线观看| 少妇熟女aⅴ在线视频| 免费电影在线观看免费观看| 非洲黑人性xxxx精品又粗又长| 小蜜桃在线观看免费完整版高清| 一级a爱片免费观看的视频| 老鸭窝网址在线观看| 又黄又爽又刺激的免费视频.| 欧美+亚洲+日韩+国产| 免费观看人在逋| 极品教师在线视频| 国产三级中文精品| 99久久无色码亚洲精品果冻| 国产精品久久电影中文字幕| 免费人成在线观看视频色| 久久热精品热| 黄色视频,在线免费观看| 国产精品伦人一区二区| 成人高潮视频无遮挡免费网站| 午夜福利欧美成人| 免费人成视频x8x8入口观看| 在线播放国产精品三级| 亚洲电影在线观看av| 国产精品日韩av在线免费观看| 中亚洲国语对白在线视频| 小蜜桃在线观看免费完整版高清| 久久精品夜夜夜夜夜久久蜜豆| 男人和女人高潮做爰伦理| 国产成人a区在线观看| 一个人看的www免费观看视频| 麻豆国产97在线/欧美| 国产在视频线在精品| 欧美又色又爽又黄视频| 午夜老司机福利剧场| 亚洲一区二区三区不卡视频| 亚洲av.av天堂| 日本黄色片子视频| 亚洲国产高清在线一区二区三| 观看美女的网站| 人妻丰满熟妇av一区二区三区| 五月伊人婷婷丁香| 欧美日韩福利视频一区二区| 国内精品一区二区在线观看| 我要看日韩黄色一级片| 婷婷丁香在线五月| 99视频精品全部免费 在线| www.999成人在线观看| 亚洲av免费高清在线观看| 一个人看视频在线观看www免费| 深夜精品福利| 麻豆国产av国片精品| 国产色爽女视频免费观看| 自拍偷自拍亚洲精品老妇| 综合色av麻豆| 国产av一区在线观看免费| 日韩免费av在线播放| 亚洲国产欧美人成| 久久久久精品国产欧美久久久| 日韩成人在线观看一区二区三区| 97热精品久久久久久| 国产精品亚洲美女久久久| 日韩欧美三级三区| 亚洲久久久久久中文字幕| 国产高潮美女av| 午夜亚洲福利在线播放| 窝窝影院91人妻| 亚洲片人在线观看| 久久久国产成人精品二区| 亚洲电影在线观看av| 亚洲av五月六月丁香网| 一进一出好大好爽视频| 久久亚洲真实| 日韩欧美在线二视频| 午夜福利高清视频| 性插视频无遮挡在线免费观看| 高清在线国产一区| 无遮挡黄片免费观看| 久久九九热精品免费| 在线十欧美十亚洲十日本专区| 色综合站精品国产| 美女被艹到高潮喷水动态| 草草在线视频免费看| 成人性生交大片免费视频hd| 欧美日韩瑟瑟在线播放| 男女床上黄色一级片免费看| x7x7x7水蜜桃| 在线a可以看的网站| 国产精品爽爽va在线观看网站| 国模一区二区三区四区视频| 丁香欧美五月| 91在线精品国自产拍蜜月| 日本一本二区三区精品| 老熟妇仑乱视频hdxx| 欧美成人a在线观看| 啦啦啦韩国在线观看视频| 国产精品久久久久久亚洲av鲁大| 国产精品女同一区二区软件 | 国产黄色小视频在线观看| 亚洲在线自拍视频| 久久精品国产清高在天天线| 黄色丝袜av网址大全| 亚洲欧美日韩无卡精品| 免费在线观看亚洲国产| 此物有八面人人有两片| 69人妻影院| 18+在线观看网站| 免费电影在线观看免费观看| 91麻豆av在线| 国产三级中文精品| 在现免费观看毛片| 人妻制服诱惑在线中文字幕| 麻豆国产97在线/欧美| 国产久久久一区二区三区| 人人妻,人人澡人人爽秒播| www.www免费av| 在线观看舔阴道视频| 97超视频在线观看视频| 亚洲av不卡在线观看| 又粗又爽又猛毛片免费看| 日本 欧美在线| 欧美激情国产日韩精品一区| 哪里可以看免费的av片| 中文字幕免费在线视频6| 国产精品影院久久| 久9热在线精品视频| 熟女电影av网| 亚洲精华国产精华精| 欧美乱色亚洲激情| 黄色视频,在线免费观看| 成人精品一区二区免费| 亚洲,欧美精品.| 日本在线视频免费播放| 丁香欧美五月| 麻豆av噜噜一区二区三区| 神马国产精品三级电影在线观看| 日韩高清综合在线| 欧美精品啪啪一区二区三区| 成人特级av手机在线观看| 直男gayav资源| 国产真实伦视频高清在线观看 | 成人av在线播放网站| 国产精品98久久久久久宅男小说| 12—13女人毛片做爰片一| 男人和女人高潮做爰伦理| 亚洲成人免费电影在线观看| 免费人成视频x8x8入口观看| 国产黄片美女视频| 日本一二三区视频观看| 中文亚洲av片在线观看爽| 一区二区三区四区激情视频 | 在线观看66精品国产| 免费观看人在逋| 一本综合久久免费| 18禁在线播放成人免费| 亚洲午夜理论影院| 综合色av麻豆| 亚洲中文日韩欧美视频| 久久久久久国产a免费观看| 淫妇啪啪啪对白视频| 宅男免费午夜| 中文在线观看免费www的网站| 色综合亚洲欧美另类图片| 色尼玛亚洲综合影院| 久久婷婷人人爽人人干人人爱| 最新在线观看一区二区三区| 日韩精品青青久久久久久| 成人性生交大片免费视频hd| 成人毛片a级毛片在线播放| 精品欧美国产一区二区三| 全区人妻精品视频| 日本 欧美在线| 激情在线观看视频在线高清| 免费大片18禁| 色综合婷婷激情| 国产精品三级大全| 淫妇啪啪啪对白视频| 日韩欧美一区二区三区在线观看| 亚洲一区高清亚洲精品| 久久热精品热| 最近在线观看免费完整版| 又紧又爽又黄一区二区| 日本a在线网址| 成人永久免费在线观看视频| 国产精品三级大全| 日韩大尺度精品在线看网址| 国产高清激情床上av| 国产精品伦人一区二区| 日本与韩国留学比较| x7x7x7水蜜桃| 欧美+亚洲+日韩+国产| 成人性生交大片免费视频hd| 国产一级毛片七仙女欲春2| www.www免费av| av天堂中文字幕网| 99国产精品一区二区蜜桃av| 日韩国内少妇激情av| 欧美日韩乱码在线| 亚洲一区二区三区不卡视频| 亚洲av电影在线进入| 国产在线男女| 成人特级av手机在线观看| 免费一级毛片在线播放高清视频| 精品午夜福利在线看| 国内久久婷婷六月综合欲色啪| 国产精品久久久久久精品电影| 内地一区二区视频在线| 精品久久久久久久久亚洲 | 成年免费大片在线观看| 最好的美女福利视频网| 精品无人区乱码1区二区| 日本与韩国留学比较| 欧美色欧美亚洲另类二区| 婷婷精品国产亚洲av在线| 可以在线观看的亚洲视频| 国产高清视频在线播放一区| 国产欧美日韩一区二区精品| 亚洲中文字幕一区二区三区有码在线看| 性色avwww在线观看| 精品国产亚洲在线| 在线看三级毛片| 热99在线观看视频| 国内久久婷婷六月综合欲色啪| 久久婷婷人人爽人人干人人爱| 国产av一区在线观看免费| 精品乱码久久久久久99久播| 99精品在免费线老司机午夜| 丰满乱子伦码专区| 久久久久久久久久成人| av视频在线观看入口| 午夜两性在线视频| 午夜精品在线福利| 成人国产一区最新在线观看| 日本黄色片子视频| 国产一区二区在线观看日韩| 99久久成人亚洲精品观看| 久久久久久久久久黄片| 国产激情偷乱视频一区二区| 丰满乱子伦码专区| 国产精品99久久久久久久久| 亚洲av熟女| 久久香蕉精品热|