• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    An ammonia-free denitration method: Direct reduction of NOx over activated carbon promoted by Cu-K bimetals

    2022-05-30 05:05:22XIAORaoZHANGJunfengZHAOLingkui
    燃料化學(xué)學(xué)報(bào) 2022年5期

    XIAO Rao ,ZHANG Jun-feng,* ,ZHAO Ling-kui

    (1. Department of Environmental Science and Engineering, College of Environment and Resources, Xiangtan University,Xiangtan 411105, China;2. Hunan Provincial Environmental Protection of Engineering Technology Center of Air Complex Pollution control (XTU),Xiangtan 411105, China)

    Abstract: As ammonia slip becomes more serious with the traditional deNOx application, ammonia-free technologies have received more and more attention recently. Cu-K bimetal loaded activated carbon catalysts were prepared by equivalentvolume impregnation method for the direct reduction of NO and showed good NO reduction performance in a wide temperature range under temperature-programmed surface reactions (TPSRs) conditions in aerobic and anaerobic environments. The catalysts were characterized by BET, SEM, XRD, XPS, H2-TPR, Raman and FT-IR techniques and the NO reduction mechanism was analyzed. Experimental results show that the active functional groups formed on the surface of activated carbon are the important intermediate products and play a key role in the reduction reaction. The presence of O2 greatly promotes the formation of the intermediate, C(O) (Oxygen-containing functional groups on the carbon surface),leading to the increase reduction rate of NO. The bimetallic oxides catalysts are obviously effective to directly reduce NO.When the ratio of copper: potassium is 2∶1, the NO reduction efficiency is about 90% at 300 °C. The catalytic activity mainly depends on the redox cycle of CuO/Cu2O, and the potassium inhibits the agglomeration of copper on the surface of carbon materials and enhances the catalytic reactivity of Cu.

    Key words: activated carbon;ammonia-free denitration;bimetal catalysis;Cu;K

    Small and medium-size coal-fired boilers are major anthropogenic emissions sources of NOx, which still hold a large market share and are widely distributed in China[1,2]. Nitrogen oxides (NOx) leads to air pollution, acid rain and photochemical smog[3-5].Ammonia slip from the traditional deNOxsystem has been widely concerned in the past two decades, which is considered to be the main factor that causes frequent smog in a large area even after sulfur dioxide (SO2) and NOxare effectively controlled[6-8]. Therefore, the development of ammonia-free denitration technology is particularly urgent.

    Selective catalytic reduction (SCR)[9]and selective non-catalytic reduction (SNCR)[10]are usually used for the NOx reduction when NH3is used as the reducing agent. However, there are some major problems with the SCR-NH3, such as high cost of construction and regeneration of the deactivated catalysts as well as NH3slip[11]. The problem of NH3slip also exists in the SNCR system[12,13]. Since 1970s and 1980s, the researches on NOxreduction at high temperatures by carbonaceous solids have been reported[14-19]. Carbon is considered as one of the promising materials for the removal of NO without ammonia. Over the past few years, activated carbon has attracted considerable attention due to its excellent advantages including excellent absorbability, low-temperature stability and high-temperature reduction[20,21]. The critical point is how to reduce the reaction temperature and improve the carbon utilization. In general, the different metal modification plays a huge influence on the selectivity and reducibility of carbon. Accordingly, some monometal oxides catalysts, such as alkali metals Ca, K, Cs,transition metals Cu, Fe, Ni Co, and noble metal Pt,etc, have been studied as catalysts loaded on activated carbon for removal of NO[22-26]. Alkali metals Cs, K can strongly enhance the C-NOxreaction without substantial carbon consumption by O2[27-29]. Ca as the active component can reduce the generation of CO2[30].In the NO reduction by C-based catalysts, transition metals can notably increase the N2selectivity[31-36].Different transition metals also have different performance in the catalytic reduction process. Less CO is released over Cu/Carbon in the process of deNOx. Cu/Carbon has higher selectivity to N2than Fe/Carbon[37]Ni/Carbon exhibits the highest N2selectivity for NOxreduction[38]. In addition, the transition metals differ in C-NOxreactions due to their different redox cycle capacity[27,39]. Feng et al.[40]studied the synergistic catalytic effect of alkali metal K and transition metal Cu on carbon reduction denitrification.A systematic investigation on the influence mechanism as well as a connection between bimetallic catalysis and NO conversion has rarely been reported so far.

    In this study, the catalytic carbon reduction of NOx(CharR-NOx) was used to reduce the NOxin the flue gas. Carbon was used as a reducing agent and catalyst carrier modified by catalytic active components. The reaction mechanism was analyzed using temperatureprogrammed surface reactions (TPSRs). The catalytic effect of Cu-K bimetals on the reaction, along with the effect of oxygen in flue gas, was investigated to provide valuable research reference for the promotion of ammonia-free denitration technologies in industry.

    1 Experimental

    1.1 Material preparation

    Shanghai Qiyue coconut-shell activated carbon(CSAC) was selected, ground, and screened to get 20-40 mesh particles. It was pretreated by boiling with deionized water to remove any water-soluble and volatile substances (such as ash and impurities) on the surface and the internal pores of the activated carbon.In addition, elemental analysis of the unmodified coconut-shell activated carbon was carried out using the Vario El Cube elemental analyzer. The result is shown in Table 1.

    Table 1 Elemental analysis of coconut-shell activated carbon

    The specific surface area and pore size of the activated carbon were calculated by the multi-point BET method and BJH method using the Quantachrome NOVA2200E automatic physical adsorption instrument. The result is shown in Table 2.

    Table 2 Surface area and pore volume of CSAC obtained by BET (N2, 77 K)

    The pretreated coconut-shell activated carbon(CSAC) was loaded with different types of metal oxide catalysts containing 10% MxO (metal oxide: CuO or K2O) using the equal-volume impregnation method with metal nitrate as the precursor. Using CuO as a preparation process sample, an appropriate amount of copper nitrate (Cu(NO3)2) was dissolved in water to prepare a salt solution, and the pH value was adjusted to 1-3 using nitric acid (HNO3). Then, the pretreated CSAC was added to the salt solution and sealed with plastic wrap. The mixture was subjected to ultrasonic treatment at 28 kHz for 30 min, soaked at room temperature for 12 h, and then placed in a blast-drying oven to dry at 90 °C for 12 h. Finally, Cu-CSAC was prepared by calcination at 400 °C for 2 h under the protection of N2atmosphere. In this study, copper and potassium bimetallic catalytic reducing agents with a total load of 10% were prepared and denoted asnCumK-CSAC, andn∶mwas the ratio of copper to potassium.

    1.2 Characterization

    The FT-IR spectra of catalysts were obtained by using ALPHA Fourier transform infrared spectrometer(Bruker Technologies, China) in the wavelength range of 400-4000 cm-1. Raman spectra of catalysts with different bimetallic components were obtained by using INVIA laser microscopy confocal Raman spectrometer(Renishaw, Britain) in the wavelength range of 50-3200 cm-1. An automatic D/MAX-2500/PC X-ray polycrystalline powder diffractometer (Rigaku, Japan)was used to obtain the XRD spectra of catalysts before and after the reaction by scanning with the Cu-Kα radiation source in the scanning range of 2θ=5°-90°.Zeiss Sigma 300 scanning electron microscope (Zeiss,Germany) was used to obtain the surface morphology images of catalysts before and after loading and reaction. Peak fitting and elemental analysis of catalysts before and after reaction were carried out by Thermo Scientific K-Alpha X-ray photoelectron spectroscopy (Thermo, America). The H2-TPR experiments were performed on AutoChem 2920 equipment (Micromeritics, America) to study the reduction behavior of active phases and metal species under different conditions.

    1.3 Material activity measurements

    The programmed temperature surface reductions(TPSRs) experiment of the materials for removal of NO was measured in a fixed bed quartz reactor (i.d.12 mm) at atmospheric pressure, as shown in Figure 1.The temperature range of the TPSRs experiment was 300-540 °C, and the heating rate was 3 °C/min. The simulated flue gas (SFG) components included 0.05%NO, 0-6% O2, and N2as the balanced gas.Subsequently, the SFG with different oxygen concentrations was mixed in the premixer to acquire the desired concentration. A gas hourly space velocity(GHSV) was 8000 h-1(the material mass was 2.0 g),which corresponded to a total flow rate of 600 mL/min during the experiments. The gas, including NO, O2, CO and CO2, was analyzed continuously with a C-600 multi-component flue gas analyzer (Seitron, France).

    Figure 1 Schematic diagram of the CharR-NOx reaction unit

    The reduction rate of NO was calculated as follows:

    Carbon material consumption was defined as the mass of carbon material consumed in the process of programmed temperature surface reduction reaction.The carbon material generated the main oxidation product CO2and by-product CO after the CharR-NOxreaction. Therefore, the consumption of carbon material could be obtained by integrating the curves of products to calculate as the following formula.

    where,Vm: the molar volume of the standard gas, 22.4 L/mol;MC: the molar mass of the carbon, 12;Q: the simulated smoke flow, 600 mL/min;t: the programmed heating time, 72 min.

    2 Results and discussion

    2.1 Reaction activity

    2.1.1 Effect of inlet oxygen concentration

    Figure 2 shows the denitration rate of the coconutshell activated carbon without metal loaded at different reaction temperatures and oxygen levels.

    Figure 2 Effect of the inlet oxygen concentration on the CharR-NOx reaction

    From Figure 2, it can be seen that the reduction rate of NO is higher when the reaction temperature is higher, and the denitration growth rate in an aerobic environment is significantly higher than that in an anaerobic environment. The overall denitration rate is less than 20% at low temperatures (300 -400 °C).Starting from 400 °C, the denitration rate by CSAC increases significantly in an aerobic environment. At 6% oxygen content, the denitration rate reaches 100%at 470 °C, and it is over 90% at 500 °C at 2% and 4%oxygen levels. In an anaerobic environment, the denitration rate is only about 20%, indicating that oxygen has an obvious promotion effect on CharR-NOxespecially at high temperatures. At the oxygen levels of 2% and 4%, the minimum temperature of 90%denitration (t90) exhibits no obvious deviation.However, the minimum temperature of 100%denitration (t100) at the 6% inlet oxygen content is significantly lower than those at 2% and 4% oxygen levels, indicating that an oxygen-rich environment is conducive to the downward shift of the CharR-NOxreaction temperature window.

    2.1.2 Effect of bimetallic catalysis

    Figure 3 shows the denitration effect of coconutshell activated carbon materials modified by 10%bimetallic copper and potassium with different loading proportions in aerobic and anaerobic environments. It also shows a comparison oft50(the minimum temperature at 50% denitration efficiency) andt90(the minimum temperature at 90% denitration efficiency)under different oxygen levels.

    Figure 3 Effects of bimetallic catalysis on the reduction rate of the CharR-NOx reactions without oxygen ((a), (c)) and aerobic ((b),(d)) environments

    As can be seen in Figure 3(a), in the absence of oxygen, irrespective of the transition metal copper,alkali metal potassium, or bimetallic synergy, the CharR-NOxreactivity of the modified carbon material is greatly improved. However, at about 300 °C, the synergistic effect of bimetals is not obvious, and the catalytic reduction effect of a single metal on NO is more obvious. Nevertheless, by comparing thet50andt90in Figure 3(c), especially the contrast line oft90, it can be seen that bimetallic synergy significantly reduces the temperature window of efficient denitration. Thet90values of 2Cu-K-CSAC, Cu-KCSAC, K-CSAC, and Cu-CSAC are 370, 390 , 395 and 405 °C, respectively. The best condition is copper∶potassium= 2∶1. In other words, 2Cu-K-CSAC can achieve a 90% NO reduction rate at the lowest temperature (370 °C).

    It can also be seen from Figure 3(b) and 3(d) that the catalytic reduction of metals is quite obvious in an aerobic environment. Similar to the oxygen-free environment, by comparing thet90with that of unmodified coconut-shell activated carbon, it can be seen that the synergistic catalytic reduction of bimetals has a significant effect on reducing the reaction temperature window. Thet90values of 2Cu-K-CSAC,Cu-K-CSAC, K-CSAC, Cu-CSAC, and CSAC are 300, 325, 390, 325, and 510 °C, respectively. As copper∶potassium= 2∶1, 2Cu-K-CSAC can achieve a 90% NO reduction rate at 300 °C.

    2.1.3 Carbon consumption

    Figure 4 shows a comparison of the total carbon consumption of different metals modified carbon materials in the process of the TPSRs. As can be seen from Figure 4(a), in the absence of oxygen, the total carbon consumption is closely and positively correlated with the NO reduction efficiency of each material. In an anaerobic, the total carbon consumption is low (<18 mg). It can be inferred that under this reaction condition the carbon consumption is mainly by the oxidation-reduction of carbon and NO. As can be seen in Figure 4(b), the total carbon consumption increases significantly, and the main carbon loss comes from the highly active oxidation reaction between oxygen and carbon materials, which is the main side reaction in the CharR-NOxreaction process. In particular, the total carbon consumption increases significantly with the increase of the alkali metal potassium loading. This is probably because alkali metals have a more significant promotion effect on the carbon-oxygen reaction and a more obvious effect on CO2production.

    Figure 4 Total carbon consumption of bimetallic catalytic carbon materials in the absence of oxygen (a) and oxygen (b)

    It is difficult to meet the requirements of an oxygen-free environment during actual applications, so the materials that can still maintain low carbon consumptions in a low-oxygen environment become the object of further research.

    2.2 Structural properties

    2.2.1 FT-IR spectroscopy

    Figure 5 shows the infrared spectrum of coconutshell activated carbon during each stage of the modification process. A characteristic peak is observed at 3450 cm-1, which is assigned to the stretching vibration absorption peak of hydroxyls (-OH) on the original carbon skeleton. The peaks at 1635 cm-1and 1060 cm-1correspond to the stretching vibration absorption peaks of ethylene linkages (C=C) and carbon-oxygen single bonds (C-O), respectively. They are all chemical bond structures on the original carbon skeleton, and it can be seen from the figures that the modification process has no specific effect on the types of C, H, and O functional groups, or the saturation of the carbon chain. In addition, after impregnation and before calcination, there is a sharp aliphatic nitro group(-NO2) characteristic absorption peak at 1386 cm-1for K-CSAC and Cu-CSAC, which disappears after calcination. It can be seen that the nitrate on the precursor can be completely decomposed after calcination at 400 °C, forming metal oxides on the surface of the carbon. The peak around 600 cm-1in the non-characteristic region can be attributed to the characteristic peak of the metal-oxygen bond (M-O). It is found that the C-O bond and the metal-oxygen bond(Cu-O) increase significantly after the impregnation of Cu-CSAC, indicating that the impregnation effect of copper nitrate is significantly higher than that of potassium nitrate. At 3780 cm-1, the double-frequency peak of hydroxys (-OH) appears in the calcinated coconut-shell activated carbon material, which indicates that the surface scattering of the calcinated carbon is enhanced and the surface flaws are increased.

    Figure 5 FT-IR spectra of the CSAC modification process

    2.2.2 Raman spectroscopy

    In Figure 6, the Raman spectra of bimetallic supported coconut-shell activated carbon materials are shown. The symmetric stretching vibration caused by thesp2hybridization of the carbon atom leads to the scattered D-peak near 1350 cm-1, which represents the occurrence of defects in the internal lattice of the carbon material and the degree of disorder of the material. The tensile vibration caused by thesp2hybridization of the carbon atom leads to the scattered G-peak near 1350 cm-1, which is the characteristic peak of the carbon material itself. It can be seen from the Raman spectra that the coconut-shell activated carbon has two peaks of the carbon material before and after modification. The load modification of Cu with a high atomic weight makes the D-peak shift of CSAC move to the lower band. With metal modification, the halfpeak width and peak area of CSAC increase, and the increase in the bimetallic supporting materials are more obvious, which is consistent with the phenomenon that the types of doping components increase.

    Figure 6 Raman spectrogram of Cu-K bimetal supported CSAC

    The intensity ratio of the D-peak to G-peak (R=ID/IG) is used to reflect the degree of disorder of the activated carbon materials. It is found that, the higher the number of active sites of the CharR-NOxreaction,the stronger the intensity of the D-peak, the higher the R-value, and the higher the degree of disorder of the materials. The R-value of the unmodified CSAC is 0.703. With the loading of metal elements, the Rvalues of the different metals modified CSAC increase,which is consistent with the phenomenon of the frequency-doubling peak in the FT-IR spectrum shown in Figure 5. The R-values of Cu-CSAC, 2Cu-K-CSAC,Cu-K-CSAC, and K-CSAC are 1.099, 1.158, 1.069,and 1.062, respectively. Among them, the R-value of 2Cu-K-CSAC exhibits the most obvious increase,which is consistent with the experimental phenomenon in Figure 3 whereby the 2Cu-K-CSAC exhibits optimal reactivity. At the 1614 cm-1Raman shift, 2Cu-K-CSAC exhibits a disorder-induced peak (D′-peak) with a weak signal, which also belongs to the characteristic band generated by the disorder between carbon atoms[41].Finally, it is worth mentioning that the G-peak of Cu-CSAC is split, forming a weak G--peak, which is related to the copper element loading capacity and its better performance in terms of carbon consumption.

    2.2.3 SEM

    The SEM micrographs of CSAC, 2Cu-K-CSAC,and Cu-CSAC before the CharR-NOxreaction are shown in Figure 7. It can be seen that the pore structure of the coconut-shell activated carbon is obvious and its surface is smooth. Significant macropores (around 500 nm) can be observed with a uniform pore size distribution, which promotes the loading of metal oxides on the surface. From Figures 7(a), 7(b) and 7(c),it can be seen that some holes on the surfaces of 2Cu-K-CSAC and Cu-CSAC collapse, and their surfaces become rough. With the pore size increase, the differences in the pore size distribution become larger.

    High-magnification SEM micrographs (×50000)of 2Cu-K-CSAC and Cu-CSAC are shown in Figures 7(c) and 7(e). After the loading of CuO or CuO/K2O,the metal oxides (<100 nm) are mainly dispersed in the inner wall and in the vicinity of the macropores.CuO/Cu2O/K2O is mainly loaded with irregular spherical particles on the 2Cu-K-CSAC, and is relatively dispersed. The CuO/Cu2O on the Cu-CSAC is mainly loaded with irregular star-shaped particles,and its distribution is relatively dense. These indicate that the distribution of metal oxides on 2Cu-K-CSAC is more uniform, which further confirms the conclusion that the alkali metal potassium inhibits the aggregation of copper on the surface of the coconut-shell activated carbon to a certain extent, as shown in the XRD analysis.

    The SEM micrographs of 2Cu-K-CSAC and Cu-CSAC after the CharR-NOxreaction are shown in Figure 8. The structures of the 2Cu-K-CSAC and Cu-CSAC coconut-shell activated carbon are unstable and crushed at high temperatures after participating in the CharR-NOxreaction. The crushing phenomenon of 2Cu-K-CSAC is more obvious, and the coconut-shell activated carbon matrix fracture and pore collapse are more severe, so the carbon loss of the material is more serious. This is consistent with the results of CharRNOxreactivity and the material carbon balance in Figure 3 and Figure 4.

    The Prince later remarked that he thought Diana was a very jolly and attractive girl, full of fun, though Diana herself believed that he barely noticed me at all.

    Figure 7 SEM images of CSAC (a), 2Cu-K-CSAC ((b), (c)), and Cu-CSAC ((d), (e))

    Figure 8 SEM images of 2Cu-K-CSAC (a) and Cu-CSAC (b) after participation in reactions

    2.3 Redox properties

    2.3.1 XRD

    Figure 9 shows the XRD patterns of CSAC loaded with different metals. It can be seen from the figure that the broadened diffraction peaks of the graphitized structure exist at 2θ=24.6° for all the samples before and after the CharR-NOxreaction, and the diffraction peaks of carbon materials also exist at 2θ=43.9° and 51.2° for all the samples. Thus, the basic structure of the carbon material remains unchanged throughout the reaction process, and the broadened diffraction peaks indicate that it is an amorphous carbon structure, which is consistent with the results of Raman spectrum analysis in Figure 6.

    Furthermore, Figure 9 shows that CuO and Cu2O are the main crystalline phases in the Cu-CSAC (a) and 2Cu-K-CSAC (b) samples. Unreacted modified coconut-shell activated carbons (Cu-CSAC-Before,2Cu-K-CSAC-Before) only have a few characteristic diffraction peaks of CuO/Cu2O with weak signals,indicating that the CuO/Cu2O exist on the surface of the coconut-shell activated carbon as an amorphous crystal with uniform loading and good dispersion.Further, the XRD signal of K-CSAC is weak, but also has very obvious characteristic diffraction peaks of K2O at diffraction angles of 29.7°, 31.5°, and 39.2°.

    Figure 9 XRD patterns of CSAC loaded with different metals

    Figure 10 shows the XRD patterns of Cu-CSAC(a) and 2Cu-K-CSAC (b). Interestingly, the CuO characteristic diffraction peaks detected in the bimetallic catalytic materials with the addition of metal potassium are much fewer than those detected in the copper mono-metal supported materials before and after the reaction. These results indicate that the participation of alkali metal potassium inhibits the aggregation of copper and improves the stability of catalytic active substances on the surface of coconutshell activated carbon to a certain extent, which is consistent with the results of SEM and the better reactivity of the bimetallic materials shown in Figure 3.

    Figure 10 XRD patterns of Cu-CSAC (a) and 2Cu-K-CSAC(b) before and after the CharR-NOx reaction

    2.3.2 H2-TPR

    XRD analysis shows that the copper species in catalyst materials contain different valence states. H2-TPR experiments on the unloaded CSAC and the optimal active 2Cu-K-CSAC are performed to further explore the reducibility of copper-containing species as shown in Figure 11. It can be seen that the reduction activities of 2Cu-K-CSAC are significantly improved.There are two obvious low-temperature reduction peaks at 163 and 190 °C for 2Cu-K-CSAC, and its high-temperature reduction peak is lower than that of CSAC. A previous study[42]has shown that highly dispersed species with sufficient exposure to reducing gases can reduce the reduction temperature. Combined with XRD analysis results, the reduction peak at 163 °C can be determined as highly dispersed bulk CuO reduction, and the reduction peak at 190 °C can be attributed to Cu2O reduction to Cu. In addition, the H2-TPR results of K-CSAC show that K species can also effectively reduce the reduction temperature of carbon materials to 470 °C.

    Figure 11 H2-TPR profiles of CSAC, K-CSAC and 2Cu-KCSAC before the CharR-NOx reaction

    2.3.3 XPS

    Figure 12 and Figure 13 show the XPS spectra of CSAC and 2Cu-K-CSAC before the CharR-NOxreaction. From the O 1sdiagram of the materials, it can be seen that the oxygen content increases and metaloxygen species appear after modification, which corresponds to the results of the XRD analysis. The higher the ratio of C-O to C=O, the stronger the reaction activity of the surface-adsorbed oxygen species, because the C -O bond energy is lower,allowing it to participate in the reaction more quickly,which is consistent with the results of an active reaction.

    The surface composition and distribution of 2Cu-K-CSAC before and after the CharR-NOxreaction and the chemical states of each element are analyzed in Figure 13 and Figure 14. C is the primary original component of the activated carbon, and K is mainly distributed on the surface of the carbon in the form of K2O.

    Figure 12 XPS of CSAC

    Figure 13 XPS of 2Cu-K-CSAC before the CharR-NOx reaction

    Figure 14 XPS of 2Cu-K-CSAC after the CharR-NOx reaction

    From the Cu peaks, it can be seen that the binding energies of Cu 2p3/2are 933.18 and 934.48 eV, and the binding energies of Cu 2p1/2are 952.78 eV and 954.48 eV. Through the principal Cu LMM peak, the kinetic energy of Cu LMM is 916.8 eV. It can infer that the Cu2O crystal mainly exists on the surface. After the reduction reaction, the content of Cu(0) increases obviously, which indicates that both Cu2+and Cu+are reduced to Cu(0), which is consistent with the conclusions of XRD and TPR analysis. Cu2+has an observable collection of satellite features 943 eV.Therefore, it can also be inferred that a CuO crystal existed. The results above mentioned are consistent with the XRD results. The addition of Cu2+increases the concentration of free electrons and increases the electrical conductivity, enhancing the catalytic effect.

    From the O peak spectra, the binding energies of O 1sare 530.00, 531.64, and 533.26 eV. These corresponds to O2-(metal-oxygen) at 530.00 eV, and the surface-adsorbed oxygen species C-O and C=O at 531.64 and 533.26 eV respectively. The results of the Raman spectra show that the material has structural defects. These defects increase the concentration of free electrons which is conducive to the generation of adsorbed oxygen. The adsorbed oxygen exists on the surface of carbon materials in the form of the C(O)functional group, which is an important intermediate product of the CharR-NOxreaction. It also actively participates in the redox cycle of CuO/Cu2O and catalyzes the reaction process. The change in the oxygen species before and after the reaction is not obvious, indicating that the service life of the material is considerably long.

    According to the analysis in Table 3, the contents of Cu(II) and Cu(0) in 2Cu-K-CSAC increase before and after the reaction, while the content of Cu(I)decreases, proving that the oxidation and reduction of Cu species are carried out in the reaction process. The valence state moves slowly from the intermediate valence state to both ends, indicating that the redox cycle of the Cu species is stable. The change in Cu species on the surface of the carbon materials is analyzed using XPS curve fitting. The ratio of Cu(II) to Cu(I/0) increases as the reaction progress, which is consistent with the XRD results. Further, the reduction activity of carbon material is lower than that of oxygen and NOxoxidation, which can explain the relatively low loss of the 2Cu-K-CSAC carbon material, as shown in Figure 4.

    Table 3 Cu 2p XPS curve-fitting analysis for 2Cu-K-CSAC

    2.4 Mechanism discussion

    From above results, the existence of an important intermediate product, the C(O) functional group, is found in the process of the CharR-NOxreaction[43,44].The oxidation capacity of O2on carbon materials is better than that of NO, and the reaction activation energy between oxygen and carbon is low. Based on the FT-IR results, along with the elemental analysis results, there are certain C(O) functional groups on the surface of the activated carbon material itself. In combination with the reaction mechanism diagram of NO and O2on the surface of the carbon materials(Figure 15), it can be seen that the C(O) functional group greatly promotes the reaction, and the presence of oxygen significantly increases the formation of C(O). In the process of carbon oxidation, an increased number of active sites C*are formed on the carbon surface, which promotes the reaction to continue.Moreover, the material’s structural defects lead to the formation of adsorbed oxygen on the surface.Therefore, in an aerobic environment, the reduction efficiency increases rapidly, and the temperature window of the CharR-NOxreaction moves down.

    Figure 15 Proposed CharR-NOx reaction mechanism of NO and O2 on the carbon surface

    Based on the XRD and XPS spectroscopic results,along with the earlier reports[27,39], the possible mechanism of bimetallic catalytic denitration by carbon is shown in Figure 16. The main function of K species is to make Cu species more evenly be loaded on the surface of the material. Similarly, from the XRD results, it can be seen that, after the reaction in an aerobic environment, the characteristic diffraction peaks of CuO increase and the signals become stronger, primarily owing to the presence of a CuO/Cu2O redox cycle, as shown in Figure 16. The redox cycle of CuO/Cu2O is considered to be the key mechanism of catalyst action in the CharR-NOxreaction[45]. In the presence of oxygen, the cycle moves towards CuO, such that more characteristic diffraction peaks of CuO appear on the surface of the product. In the absence of oxygen, only the characteristic diffraction peak of Cu2O can be detected. This catalytic mechanism can well explain the phenomenon that the CharR-NOxreaction activity of the material is better in an aerobic environment because the oxygen greatly promotes the redox cycle of the catalytic active component. O2and C simultaneously promote the redox cycle of CuO/Cu2O. The redox cycle of surface Cu species promotes the renewal of the surface functional groups of carbon materials, catalyzing the reaction between C and NOx.

    Figure 16 REDOX cycle of CuO/Cu2O

    3 Conclusions

    A denitration agent without the addition of ammonia was prepared through incipient-wetness impregnation. The agent uses the reduction properties of the carbon material itself and the auxiliary catalytic effect of metals to achieve the efficient reduction of NO.

    Oxygen has a good effect in terms of promoting the CharR-NOxreaction. At a lower oxygen content(2%), the reduction efficiency reaches a relatively high level. Therefore, the oxygen concentration should not be too high; otherwise, excessive amounts of carbon materials would be lost. The bimetallic catalytic reducing agent can significantly improve the reaction efficiency of CharR-NOx. The temperature window of the reaction is reduced, and the reduction rate of NO reaches 90% at 300 °C. On the one hand, the degree of disorder of the original carbon material structure is improved and the reactive oxygen species C -O increases during the loading process. On the other hand, the main catalytic group is the transition metal copper, CuO/Cu2O redox cycle is the key mechanism affecting the catalytic process, and alkali metal potassium can significantly inhibit the surface agglomeration of copper.

    国产伦人伦偷精品视频| 三级毛片av免费| 国产精品永久免费网站| 9热在线视频观看99| 欧美+亚洲+日韩+国产| 午夜福利,免费看| 国产有黄有色有爽视频| 日本vs欧美在线观看视频| 50天的宝宝边吃奶边哭怎么回事| 建设人人有责人人尽责人人享有的| 久久精品熟女亚洲av麻豆精品| 欧美激情高清一区二区三区| 女人被狂操c到高潮| 男男h啪啪无遮挡| 黄色 视频免费看| 99re在线观看精品视频| 久久亚洲真实| 欧美日韩亚洲国产一区二区在线观看 | 中文字幕人妻熟女乱码| 免费在线观看日本一区| 999久久久国产精品视频| 亚洲成av片中文字幕在线观看| 中亚洲国语对白在线视频| 一级片'在线观看视频| 中文字幕精品免费在线观看视频| 国产日韩欧美亚洲二区| 男女之事视频高清在线观看| 国产亚洲欧美精品永久| 一级黄色大片毛片| 日韩欧美一区视频在线观看| a在线观看视频网站| 黑人猛操日本美女一级片| 色老头精品视频在线观看| 亚洲国产毛片av蜜桃av| cao死你这个sao货| 国产精品永久免费网站| 黑人巨大精品欧美一区二区mp4| 久久亚洲精品不卡| 丝袜人妻中文字幕| 50天的宝宝边吃奶边哭怎么回事| 欧美+亚洲+日韩+国产| 成人免费观看视频高清| 99久久国产精品久久久| 好看av亚洲va欧美ⅴa在| 韩国精品一区二区三区| 91成年电影在线观看| 操出白浆在线播放| 日日摸夜夜添夜夜添小说| 999久久久精品免费观看国产| 中文字幕制服av| 日韩成人在线观看一区二区三区| 国产男靠女视频免费网站| 亚洲国产中文字幕在线视频| 国产精品亚洲av一区麻豆| 国产精品电影一区二区三区 | 日本黄色日本黄色录像| a在线观看视频网站| 一级片'在线观看视频| 欧美乱码精品一区二区三区| 欧美 日韩 精品 国产| 美女高潮喷水抽搐中文字幕| 最近最新中文字幕大全免费视频| 亚洲成a人片在线一区二区| 啦啦啦在线免费观看视频4| 国产精品99久久99久久久不卡| 国产精品影院久久| 免费在线观看完整版高清| 少妇裸体淫交视频免费看高清 | 国产成人精品久久二区二区免费| 中文字幕高清在线视频| 亚洲欧美一区二区三区久久| 午夜激情av网站| 亚洲精品在线美女| 91成人精品电影| 午夜免费观看网址| 国产男女超爽视频在线观看| 国产精品久久久久久人妻精品电影| 亚洲一卡2卡3卡4卡5卡精品中文| 午夜老司机福利片| 成人18禁高潮啪啪吃奶动态图| 看黄色毛片网站| 色老头精品视频在线观看| 亚洲精品成人av观看孕妇| 亚洲中文字幕日韩| 村上凉子中文字幕在线| 日韩欧美一区视频在线观看| 黑丝袜美女国产一区| 久久久国产成人精品二区 | 如日韩欧美国产精品一区二区三区| 一区在线观看完整版| 成人手机av| 国产国语露脸激情在线看| 99久久精品国产亚洲精品| 亚洲一区高清亚洲精品| 一级片'在线观看视频| 国产成人精品久久二区二区免费| 欧美激情久久久久久爽电影 | 性色av乱码一区二区三区2| 久久九九热精品免费| 国产人伦9x9x在线观看| 老汉色∧v一级毛片| 国产欧美日韩精品亚洲av| 99香蕉大伊视频| 一区二区三区国产精品乱码| videos熟女内射| 岛国毛片在线播放| 久久精品亚洲av国产电影网| 最新美女视频免费是黄的| 变态另类成人亚洲欧美熟女 | tube8黄色片| 欧美日韩乱码在线| 亚洲精品乱久久久久久| 人人澡人人妻人| 热99国产精品久久久久久7| 欧美 日韩 精品 国产| 在线观看一区二区三区激情| 久久狼人影院| 国产一卡二卡三卡精品| 露出奶头的视频| 久久精品亚洲av国产电影网| 久久久国产成人精品二区 | 国产精品电影一区二区三区 | 免费人成视频x8x8入口观看| 99香蕉大伊视频| 制服人妻中文乱码| 热re99久久国产66热| 热re99久久精品国产66热6| 午夜福利欧美成人| 亚洲专区字幕在线| 免费在线观看影片大全网站| 欧美黑人精品巨大| 美女高潮到喷水免费观看| 99精品久久久久人妻精品| 亚洲在线自拍视频| 亚洲精品国产区一区二| a级片在线免费高清观看视频| 国产有黄有色有爽视频| x7x7x7水蜜桃| 黄色毛片三级朝国网站| 动漫黄色视频在线观看| 天堂动漫精品| 亚洲国产精品一区二区三区在线| 视频在线观看一区二区三区| 极品人妻少妇av视频| 啦啦啦视频在线资源免费观看| 少妇 在线观看| 久久天堂一区二区三区四区| 久久性视频一级片| 亚洲情色 制服丝袜| 亚洲成人免费电影在线观看| 亚洲第一青青草原| 亚洲欧美一区二区三区黑人| 女人精品久久久久毛片| 久久精品国产综合久久久| 久久久久久免费高清国产稀缺| 99re在线观看精品视频| 亚洲七黄色美女视频| 在线观看免费午夜福利视频| 久久午夜综合久久蜜桃| 色老头精品视频在线观看| 亚洲精品在线美女| 亚洲精品一二三| 电影成人av| 日本撒尿小便嘘嘘汇集6| 国产精品电影一区二区三区 | 波多野结衣av一区二区av| 日韩熟女老妇一区二区性免费视频| 看黄色毛片网站| 男男h啪啪无遮挡| 老司机亚洲免费影院| 自线自在国产av| 欧美午夜高清在线| 18禁美女被吸乳视频| 99热国产这里只有精品6| 制服人妻中文乱码| 亚洲自偷自拍图片 自拍| 日本五十路高清| 日韩欧美一区视频在线观看| 俄罗斯特黄特色一大片| 亚洲人成电影免费在线| 久99久视频精品免费| www.熟女人妻精品国产| 大码成人一级视频| 国产精品久久久人人做人人爽| 亚洲,欧美精品.| 国产精品秋霞免费鲁丝片| 女性被躁到高潮视频| 亚洲国产毛片av蜜桃av| 极品教师在线免费播放| 男人操女人黄网站| 欧美精品av麻豆av| 国产99白浆流出| 老汉色av国产亚洲站长工具| 欧美日韩视频精品一区| 人妻丰满熟妇av一区二区三区 | 日韩三级视频一区二区三区| 国产成人影院久久av| 人人澡人人妻人| 成人av一区二区三区在线看| 美女高潮喷水抽搐中文字幕| 男女下面插进去视频免费观看| tocl精华| 国产精品欧美亚洲77777| 一级毛片精品| 亚洲欧美激情在线| 色在线成人网| 日韩熟女老妇一区二区性免费视频| 中国美女看黄片| 精品第一国产精品| 在线观看免费视频日本深夜| www.999成人在线观看| 99热国产这里只有精品6| 成人永久免费在线观看视频| 老熟女久久久| 极品教师在线免费播放| 亚洲免费av在线视频| 亚洲欧美一区二区三区久久| 久久精品国产综合久久久| 一区二区日韩欧美中文字幕| 国产成人影院久久av| 午夜久久久在线观看| 精品少妇一区二区三区视频日本电影| 国产精品国产av在线观看| 中亚洲国语对白在线视频| 久久国产精品人妻蜜桃| 午夜两性在线视频| 精品视频人人做人人爽| 交换朋友夫妻互换小说| 高清av免费在线| av免费在线观看网站| 色在线成人网| 亚洲av电影在线进入| 日本wwww免费看| 在线观看免费高清a一片| 乱人伦中国视频| 丝袜美腿诱惑在线| 日本一区二区免费在线视频| 真人做人爱边吃奶动态| 日韩免费av在线播放| 日本黄色日本黄色录像| 久9热在线精品视频| 人妻丰满熟妇av一区二区三区 | 19禁男女啪啪无遮挡网站| 很黄的视频免费| 搡老熟女国产l中国老女人| 如日韩欧美国产精品一区二区三区| 久久人人爽av亚洲精品天堂| 人妻 亚洲 视频| 日韩一卡2卡3卡4卡2021年| 久久久精品区二区三区| 国产精品 国内视频| 咕卡用的链子| 国产亚洲欧美在线一区二区| 久久影院123| 欧美在线黄色| 成人国语在线视频| 国产深夜福利视频在线观看| 视频在线观看一区二区三区| 国产乱人伦免费视频| 99国产综合亚洲精品| 淫妇啪啪啪对白视频| 亚洲第一av免费看| 性少妇av在线| 久久人人97超碰香蕉20202| 麻豆av在线久日| netflix在线观看网站| 99热只有精品国产| 自拍欧美九色日韩亚洲蝌蚪91| 12—13女人毛片做爰片一| 电影成人av| 无限看片的www在线观看| 大香蕉久久网| 人妻丰满熟妇av一区二区三区 | 可以免费在线观看a视频的电影网站| 老熟妇仑乱视频hdxx| 日韩大码丰满熟妇| 侵犯人妻中文字幕一二三四区| 久久中文字幕人妻熟女| 国产激情欧美一区二区| 黄片小视频在线播放| 亚洲精品国产一区二区精华液| 精品人妻1区二区| 欧美色视频一区免费| 久久国产精品影院| 国产精品 国内视频| 国产成+人综合+亚洲专区| 久久久水蜜桃国产精品网| 91大片在线观看| 欧美精品高潮呻吟av久久| 一进一出抽搐动态| 午夜精品国产一区二区电影| 欧美色视频一区免费| 欧美成人午夜精品| 精品福利永久在线观看| 欧美日韩瑟瑟在线播放| 久久精品国产亚洲av高清一级| 美女福利国产在线| av有码第一页| 午夜免费鲁丝| 中文字幕人妻丝袜一区二区| av天堂久久9| 欧美黑人精品巨大| 成年女人毛片免费观看观看9 | 国产精品成人在线| 激情视频va一区二区三区| 亚洲精华国产精华精| 欧美 亚洲 国产 日韩一| 成人免费观看视频高清| 日日爽夜夜爽网站| 亚洲av成人av| 高潮久久久久久久久久久不卡| 亚洲视频免费观看视频| 国产人伦9x9x在线观看| 亚洲精品一二三| svipshipincom国产片| 久久国产精品男人的天堂亚洲| 夜夜夜夜夜久久久久| 一进一出抽搐gif免费好疼 | 久久国产亚洲av麻豆专区| 亚洲成av片中文字幕在线观看| 正在播放国产对白刺激| 亚洲精品一二三| 色尼玛亚洲综合影院| 亚洲第一av免费看| 欧美日韩亚洲国产一区二区在线观看 | 久久精品国产亚洲av香蕉五月 | 美女高潮喷水抽搐中文字幕| 淫妇啪啪啪对白视频| 国产一卡二卡三卡精品| 亚洲欧洲精品一区二区精品久久久| 亚洲片人在线观看| 久久草成人影院| 国产男靠女视频免费网站| 国产成人一区二区三区免费视频网站| 国产精品影院久久| 国产精品久久久av美女十八| 18禁裸乳无遮挡动漫免费视频| 久久精品国产a三级三级三级| 亚洲熟女精品中文字幕| 12—13女人毛片做爰片一| 久久九九热精品免费| 国产精品亚洲一级av第二区| 亚洲人成电影观看| 丰满饥渴人妻一区二区三| 亚洲五月天丁香| 曰老女人黄片| 中亚洲国语对白在线视频| a级毛片黄视频| 色尼玛亚洲综合影院| 99国产极品粉嫩在线观看| 母亲3免费完整高清在线观看| 老司机亚洲免费影院| 精品免费久久久久久久清纯 | 欧美日韩成人在线一区二区| 亚洲中文字幕日韩| 亚洲精品中文字幕一二三四区| xxx96com| 国产亚洲一区二区精品| av国产精品久久久久影院| 日韩欧美一区视频在线观看| 最新在线观看一区二区三区| 大型av网站在线播放| 精品久久久久久久久久免费视频 | 日韩欧美在线二视频 | 制服诱惑二区| 99国产精品一区二区三区| 99re6热这里在线精品视频| 亚洲成a人片在线一区二区| 国产精品一区二区精品视频观看| 欧美黑人欧美精品刺激| 久久久国产成人免费| 91在线观看av| 精品国产一区二区三区四区第35| 欧美色视频一区免费| 9191精品国产免费久久| 亚洲片人在线观看| 青草久久国产| 黑人巨大精品欧美一区二区mp4| 久久久久久久精品吃奶| www日本在线高清视频| 国产精品自产拍在线观看55亚洲 | 免费高清在线观看日韩| 男男h啪啪无遮挡| 亚洲精品国产精品久久久不卡| xxx96com| 99国产精品免费福利视频| 黄片播放在线免费| 亚洲久久久国产精品| 国产高清国产精品国产三级| 他把我摸到了高潮在线观看| 中文字幕最新亚洲高清| 男女床上黄色一级片免费看| 黄片播放在线免费| 国产欧美日韩精品亚洲av| 两个人看的免费小视频| 国产一区二区三区综合在线观看| xxxhd国产人妻xxx| videosex国产| 久久精品国产综合久久久| 人人妻人人澡人人爽人人夜夜| 精品高清国产在线一区| 亚洲人成77777在线视频| 色综合婷婷激情| 五月开心婷婷网| 久久 成人 亚洲| 大香蕉久久网| 午夜日韩欧美国产| 叶爱在线成人免费视频播放| 中文字幕精品免费在线观看视频| 日本a在线网址| 无限看片的www在线观看| 欧美日韩亚洲综合一区二区三区_| 成人精品一区二区免费| 天天添夜夜摸| 无限看片的www在线观看| а√天堂www在线а√下载 | 国产精品成人在线| 老司机靠b影院| 成年人黄色毛片网站| 激情视频va一区二区三区| 99精品久久久久人妻精品| 午夜免费成人在线视频| 成熟少妇高潮喷水视频| 欧美激情 高清一区二区三区| 人妻丰满熟妇av一区二区三区 | 怎么达到女性高潮| 成人亚洲精品一区在线观看| 欧美性长视频在线观看| 最新的欧美精品一区二区| 老汉色∧v一级毛片| 久久久精品国产亚洲av高清涩受| 啦啦啦免费观看视频1| 黑人猛操日本美女一级片| 美女高潮喷水抽搐中文字幕| 色播在线永久视频| 天天操日日干夜夜撸| 久久国产精品影院| 99精品久久久久人妻精品| 女人高潮潮喷娇喘18禁视频| www.精华液| 欧美黑人欧美精品刺激| 黑人操中国人逼视频| 久久精品国产亚洲av高清一级| 一级a爱视频在线免费观看| 成年人黄色毛片网站| 成人国产一区最新在线观看| 中出人妻视频一区二区| 欧美激情 高清一区二区三区| 一级毛片精品| а√天堂www在线а√下载 | 51午夜福利影视在线观看| 久久中文字幕人妻熟女| 9色porny在线观看| 极品少妇高潮喷水抽搐| 黄片大片在线免费观看| 热re99久久精品国产66热6| 久久九九热精品免费| 精品一区二区三区视频在线观看免费 | 黄色 视频免费看| 最近最新中文字幕大全免费视频| 咕卡用的链子| 视频区欧美日本亚洲| 精品一区二区三区av网在线观看| 日本欧美视频一区| 欧美成人免费av一区二区三区 | 午夜福利在线免费观看网站| 最新美女视频免费是黄的| 女人高潮潮喷娇喘18禁视频| 国产欧美日韩综合在线一区二区| 黄网站色视频无遮挡免费观看| 一级片免费观看大全| 色老头精品视频在线观看| 天堂中文最新版在线下载| 美国免费a级毛片| 午夜福利在线免费观看网站| 国产成人免费无遮挡视频| 国产精品综合久久久久久久免费 | 亚洲成人手机| 狠狠狠狠99中文字幕| 一二三四在线观看免费中文在| 欧美成狂野欧美在线观看| 国产精品影院久久| 欧美国产精品一级二级三级| 久久久水蜜桃国产精品网| 热re99久久国产66热| 精品高清国产在线一区| av网站免费在线观看视频| 丝袜在线中文字幕| 中出人妻视频一区二区| 亚洲成av片中文字幕在线观看| 99久久99久久久精品蜜桃| 天堂中文最新版在线下载| 午夜两性在线视频| 色婷婷av一区二区三区视频| 国产xxxxx性猛交| 亚洲情色 制服丝袜| 天天添夜夜摸| 一二三四在线观看免费中文在| av福利片在线| 精品视频人人做人人爽| 日日夜夜操网爽| 99久久国产精品久久久| 国产在线一区二区三区精| 午夜久久久在线观看| 啦啦啦 在线观看视频| 国产精品乱码一区二三区的特点 | a级毛片在线看网站| 亚洲国产欧美日韩在线播放| 自拍欧美九色日韩亚洲蝌蚪91| 高清视频免费观看一区二区| 无限看片的www在线观看| 一区二区三区精品91| av线在线观看网站| 国产精品欧美亚洲77777| 欧美激情极品国产一区二区三区| 美女国产高潮福利片在线看| 欧美日韩福利视频一区二区| 精品一区二区三卡| 啦啦啦在线免费观看视频4| 在线看a的网站| 欧美亚洲日本最大视频资源| 婷婷丁香在线五月| 久久久水蜜桃国产精品网| www日本在线高清视频| 波多野结衣一区麻豆| 欧美精品高潮呻吟av久久| 国产在线精品亚洲第一网站| 欧美日韩乱码在线| 动漫黄色视频在线观看| 狂野欧美激情性xxxx| 中文字幕人妻丝袜一区二区| 欧美国产精品va在线观看不卡| 欧美日韩视频精品一区| 美女午夜性视频免费| 亚洲 欧美一区二区三区| 精品免费久久久久久久清纯 | 久久久久视频综合| 国产欧美日韩精品亚洲av| 757午夜福利合集在线观看| 久久香蕉激情| av在线播放免费不卡| 精品国内亚洲2022精品成人 | 国产亚洲精品一区二区www | 午夜影院日韩av| 美女扒开内裤让男人捅视频| 午夜福利一区二区在线看| 日韩有码中文字幕| 我的亚洲天堂| 国产精品.久久久| 欧美 亚洲 国产 日韩一| 日韩精品免费视频一区二区三区| 一进一出抽搐动态| 精品久久久久久,| 男女高潮啪啪啪动态图| 国产一区二区三区综合在线观看| 精品久久久精品久久久| 亚洲aⅴ乱码一区二区在线播放 | 国产日韩一区二区三区精品不卡| 日韩欧美一区二区三区在线观看 | 不卡一级毛片| 欧美日韩一级在线毛片| av天堂在线播放| 91大片在线观看| 免费女性裸体啪啪无遮挡网站| 黄色 视频免费看| 校园春色视频在线观看| 少妇被粗大的猛进出69影院| 久久午夜综合久久蜜桃| 十八禁网站免费在线| 国产1区2区3区精品| 18禁国产床啪视频网站| 亚洲精品久久午夜乱码| 色94色欧美一区二区| 国产免费男女视频| 免费看十八禁软件| 国产高清视频在线播放一区| 国产精品秋霞免费鲁丝片| 日韩 欧美 亚洲 中文字幕| 精品午夜福利视频在线观看一区| 欧美老熟妇乱子伦牲交| 久久久精品国产亚洲av高清涩受| 自线自在国产av| 精品一区二区三区四区五区乱码| 亚洲少妇的诱惑av| 中出人妻视频一区二区| 精品一品国产午夜福利视频| 久久人人爽av亚洲精品天堂| 亚洲精品粉嫩美女一区| 亚洲av成人一区二区三| 五月开心婷婷网| 亚洲情色 制服丝袜| 90打野战视频偷拍视频| 久久国产精品人妻蜜桃| www.999成人在线观看| 99久久99久久久精品蜜桃| 国产午夜精品久久久久久| 真人做人爱边吃奶动态| 91精品三级在线观看| 欧美乱码精品一区二区三区| 69av精品久久久久久| 97人妻天天添夜夜摸| 免费观看a级毛片全部| 国产高清视频在线播放一区| 人成视频在线观看免费观看| 女性被躁到高潮视频| a在线观看视频网站| 亚洲熟女毛片儿| 黄色片一级片一级黄色片| 12—13女人毛片做爰片一| 日本vs欧美在线观看视频| 黄色女人牲交| 亚洲欧洲精品一区二区精品久久久| 久热这里只有精品99| 黄色怎么调成土黄色| 老司机影院毛片|