• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Analysis of Drilling Riser in Re-entry Operation Under Complex Currents

    2019-12-30 06:45:52-,-,
    船舶力學(xué) 2019年12期

    -,-,

    (1.Logistics Engineering College,Shanghai Maritime University,Shanghai 201306,China;2.School of Naval Architecture,Ocean and Civil Engineering,Shanghai Jiao Tong University,Shanghai 200240,China)

    Abstract: In order to complete the operation accurately and safely, the dynamic characteristics of risers in re-entry, especially the riser deformation and the distance from lower-end to wellhead, should be studied precisely.Although the re-entry operation generally occurs when the destructive sea condition turns slightly better, there most likely exists a complex current due to the great operating water depth. However, the dynamics calculation for re-entry in previous research ignored the influence of currents. In this paper, a more accurate model is provided to describe the dynamic behavior of risers in re-entry operation considering three different currents (uniform, skewed, bilateral) that may occur in real sea-conditions.We adopted the Finite Difference Approximation (FDA)method to simplify the original partial differential equations into a linear equation set. According to the characteristics of the riser in re-entry, the special initial state and the boundary conditions are set up to make the calculation more efficient. The riser deformation (shape), horizontal distance from lower-end to wellhead and the velocity of lower-end were investigated under different currents with Newton iteration scheme. In addition, we compared the effect of different currents on the re-entry operation considering possible swings based on the velocity of lower-end.From the results,some interesting and meaningful information about the riser’s features and behaviors were obtained, which is quite useful for the riser’s control scheme constitution in its practical re-entry and also can offer reference for precise and safe operations.

    Key words:riser;re-entry;complex currents;dynamics calculation;FDA;Newton iteration scheme

    0 Introduction

    In drilling operations, the drilling riser was a key component required to connect its bottom end to the blowout preventer at the seabed with both its top connected angle and its deformation controlled. The riser re-entry operation[1]means when the sea condition is getting worse or the complex current coming,the drilling risers will be pulled out of wellheads and moved to a safe location to avoid the destruction, while the sea condition gets better, the risers need to be moved and connected to the wellhead again. Fig.1 conceptually depicted the re-entry process of a drilling riser. The upper-end of riser is attached to the surface vessel and follows its motion, and the lower-end is completely free. Under the action of currents, the free lower-end would be positioned within the re-entry operation area above the wellhead located in the seabed though the movement of surface vessel,then the drilling riser installation begins. So,the horizontal distance from lower-end to wellhead directly affects the accuracy of re-entry operation.

    Fig.1 The re-entry process of a drilling riser

    However, due to the free-hanging of lower-end, the re-entry operation of drilling riser is becoming increasingly difficult with increasing water depth and now it is one of the major operations regarding deep sea drilling because manual re-entry becomes difficult in such a water depth. In addition, influence factors, especially marine environment with non-uniform currents (shear current, stratified current), could also have significant effect on the riser in re-entry operation, hydro-dynamical drag forces and the flexibility of riser also make it more difficult for them to operate it correctly. In order to accomplish the operation correctly and safely, dynamics analysis of the riser in re-entry urgently needs to be studied to predict the riser deformation and locate the lower end.

    For a long time,some studies are carried out for the free-hanging riser dynamic behaviors.Patel[2]presented a theoretical and experimental investigation of the lateral dynamics of freehanging marine risers, and the in-plane behavior had been investigated through a finite element analysis of the riser and its hydrodynamic loading.Hong[3]carried out numerical investigations on dynamics of flexible free-hanging riser with the equations of motion of riser derived based on Hamilton’s principle.Besides,Kuiper[4-5]studied the stability of a vertically suspended, fully submerged water-conveying pipe (water riser). However, for the re-entry of riser, as a particular and actual operation of free-hanging riser, there have been few study works being carried out. Suzuki[6-7]presented active control for deep-water riser’s re-entry operating systems based on previous research work about the riser,and carried out a basin experiment to investigate the coupled dynamic behaviors of the riser model.Ohtsubo[8-9]considered the entry/reentry control problem of the flexible marine riser applying LPV (Linear Parameter Varying)technique,and carried out the re-entry experiment in the towing tank to verify the results.Kajiwara[10]built and calculated the re-entry riser model considering a constant current on the upper half based on motion equation together with the mode shapes,and applied LQI(Linear Quadratic with Integral action)control methodology to obtain an appropriate re-entry controller.Recently,Wang and Xu[11]adopted specific boundary conditions to simplify the modeling of re-entry riser,and calculated the dynamics response of re-entry risers.

    Although the re-entry operation generally occurs when the destructive sea condition turns slightly better,there most likely exists a complex current due to the great operating water depth in re-entry, so we cannot ignore the influence of currents. However, most of studies mentioned above did not consider current during analyzing the dynamics of re-entry riser, the hydrodynamic drag force was thought to be entirely caused by the movement of the riser, or the steady current was only considerd, it clearly does not accurately reflect the actual operation. In order to control the horizontal distance from lower-end to wellhead, studying precisely the dynamic characteristics of risers in re-entry considering actual currents needs to be carried out.

    Hence, what is different from the conventional riser modeling in re-entry is that the current forces are added into the model in this work. The governing equations of re-entry riser were derived from the force equilibriums of external forces at node and an efficient time-domain analysis scheme was developed in this work based on finite difference approximation.The dynamic response of riser in re-entry was investigated considering uniform,skewed and bilateral currents. The riser deformation and the horizontal distance from lower-end to wellhead for re-entry were investigated under each current.Considering possible swings based on the velocity of lower-end, the advantages and disadvantages of different currents in re-entry operation were compared.

    1 Modeling of riser

    In the re-entry process, we assume that the riser is completely vertical in starting without velocity in any direction,with the upper-end hinged by a fixed connection to the surface vessel,and the riser is moved in horizontal direction,the vertical motion of riser caused by mother ship is very small, and the tension of riser is mainly caused by its self-weight. The aim of this process is to make the riser positioned accurately within the re-entry operation area above the wellhead located in the seabed.

    Here,we treat the dynamic model of riser as a beam located in the vertical plane and subjected to the tension force, the gravities of the riser and the lateral force (current force), as shown in Fig.2(a). The global coordinate system is set with thex-axis parallel to the horizontal plane and thez-axis pointing to the sea floor. The local inertial coordinate system is set along the tangential direction(t)and the normal direction(n)of the riser.

    Fig.2 Mechanical diagram of riser assumed(a)and schematic diagram of discrete model(b)

    The analysis model is established in a local inertial coordinate system based on simple Euler-Bernoulli beam theory applying the discrete analysis scheme[12]. As shown in Fig.2(b),the riser can be divided intoNnumber of discrete rigid segments withN+1 nodes, and the length of each segment is ds(L/N),whereLis the total length of riser in the re-entry process.

    Then, the differential control equations for a segment are established according to the dynamic force balance,and expressed in the tangential and normal directions,as shown in Eqs.(1-2).

    wheremis the mass of a segment,uandvare the tangential and normal velocities,respectively,Tis the dynamic tension force distribution in the tangential direction,Eis Young’s modulus,Iis the moment of inertia,wis the submerged weight of the segment,θis the angle of the node between the tangential direction and the vertical direction,fDtandfDnare the drag forces of currents in the tangential and normal directions respectively, andfMis the inertia force of currents in the normal direction.

    In addition,Eq.(3)defines the tensions and shear forces.

    We assume that the main external forces act on the nodes.fDtandfDnare the drag forces in the tangential and normal directions,respectively,andfMis the inertia force in the normal direction.The drag forces acting on riser is the result of motion of riser and current.

    whereCDtis the drag coefficient in the tangential direction,CDnis the drag coefficient in the normal direction,ρis the density of sea water,dis the outer diameter of the riser,UtandUnare the current velocities in the tangential and normal directions respectively,andCmrefers to the inertial coefficient.

    Here,u,v,UtandUnare variable in local coordinates, it is essential to simplify the representation of the results. In order to calculate expediently, their local inertial coordinates are transformed into global fixed coordinates.

    whereVxandVzare velocities of node of riser in thex- andy-directions of the global coordinate system respectively, andUis the current velocity in thex-directions of the global coordinate system.

    Introducing Eqs.(3-8)into Eqs.(1-2),we obtain the equation set for the dynamic motion of riser.

    Due to the fixed connection of the upper-end with the surface vessel,the upper-end is determined by the motion of vessel.Here,we can assume the surface vessel only sails in thex-directions.

    whereVx(1) andVz(1) represent the velocity of the first node of riser at any iteration time inxandz- directions, respectively,Pvis the velocity of surface vessel, and here it is relative to the velocity of the currents.

    And,considering boundary conditions of lower-end,there is an equation as shown in Eq.(11).

    whereM(n+ 1)represents the bending moment of then+1 node of riser.

    2 Calculation method

    To simplify the original partial differential equations to a linear equation set, a Finite Difference Approximation (FDA) method is adopted. The approximations of partial differentiations ofΘwith respect tolandtare written in Eq.(12). Then, introducing Eq.(12) into Eqs.(9-11),the linear equation set of 4N+1 nodes can be set up.

    whenΘifor the iteration timetiis obtained,Θi+1for the next iteration timeti+1could be calculated using the Newton iteration algorithm.According to this theory,the initial state (i=1)needs to be set:riser is vertically located in the water without lateral displacement and vertical velocity,as followed in Eq.(13).The setting may cause a certain deviation in the initial condition,but in contrast with large calculation depth and duration,such a deviation can be neglected.

    whereVx1andVz1are the velocity of each node at iteration time 1 inx-andz-directions respectively,θ1is the rotation angle of each node at iteration time 1,is the tension of nodej(j∈{1,2,3, …,N-1,N,N+1}) at iteration time 1,is the weight of segmentj(j∈{1, 2, 3, …,N-1,N})of riser at iteration time 1 andWeis the weight of equipment hanging at the lower-end of riser.

    We firstly assumeΘ2=Θ1to calculateΘ2via the Newton iteration algorithm.Θidenotes an approximate value in thei-th iteration for the solution of the unknown variablesΘ, and the estimated value ofΘi+1for the initial guess is obtained withΘi:

    The correction value ofΘi+1can be calculated usingΘiand the initial guess ofΘi+1:

    where ΔΘi+1is found by solving the linear equations.

    And,Ji+1is the Jacobian matrix of equationsG,

    whereG(Θi,Θi+1)=0

    If the reference variableλ≤10-10, the calculation could continue to the next iteration time step(i+2).

    Otherwise,the correction valueΘi+1(new)needs to beΘi+1(guess)to obtain a more accurate value via calculating Eqs.(14)-(17).

    3 Simulation and results

    In re-entry, the riser needs to be moved horizontally from the initial position to the target position. Now, the excellent simulation based FDA method can be done in re-entry for marine riser to predict the dynamics trajectory of riser.

    3.1 An example

    Taking an actual re-entry of riser as an example,a specific flexible marine riser is chosen as the simulation object, and the starting position of re-entry operation is about 135 meters from the target wellhead in horizontal direction.The riser is hinged vertically to the drilling vessel initially,and its features are shown in Tab.1

    The environments are selected from the combined extreme (100 year return period) for loop currents and bottom currents, containing a combination of wind,waves and currents.Thedata provide indicative values for metocean parameters which can be suitable for conceptual studies. In re-entry analysis, the governing parameter is the current velocity profile. For this thesis, three distinctive profiles are considered: uniform, skewed and bilateral. The profiles are illustrated in Fig.3.

    Tab.1 Properties of the marine riser

    Fig.3 Current profiles used in the simulations(a:uniform;b:skewed;c:bilateral)

    And these current profiles can be presented as Eqs.(19)-(21).

    With the surface vessel traveling in forward direction with a prearranged velocity, the dynamic behaviors of marine riser are simulated. The vessel’s velocity (relative to the currents) and upperend’s velocity are changing as shown in Fig.4. In the initial 30 s,the vessel moves with 0.05 m/s2acceleration forward, and with the velocity from -0.5 to 1 m/s. And then, the vessel travels at a steady speed of 1 m/s for 60 s. Finally, the vessel slows down to -0.5 m/s with 0.05 m/s2deceleration for the last 30 s. Due to the relative velocityPv, the vessel remained static at 0 s and 120 s. On the side,because the upper-end’s velocity is the superposition of vessel’s velocity and current velocity, the changing trends of it are similar to those of vessel’s velocity. And the maximum velocity of upper-end runs up to 1.5 m/s in global coordinate system.

    During the simulation time of 120 s, we mainly want to see the riser’s shape and the horizontal distance from lower-end to wellhead when the surface vessel travels with changing velocities.The riser is divided intoN=70 rigid segments with 71 nodes for calculations.The time intervals are chosen as Δt= 0.05 s. Although hydrodynamic coefficients are dependent on Reynolds number, Keulegan-Carpenter number and roughness, here, the values ofCDt,CDnandCmare taken as 0.01, 1.2, and 2, respectively, as suggested by Techet[13]for Morrison’s equations.Then,the numerical simulations of re-entry of riser under complex currents can be carried out.

    Fig.4 The time history of vessel’s and upper-end’s velocities

    3.2 Riser deformation

    In view of the re-entry operation of the free-hanging riser, the deformation of riser is of the utmost importance.With the upper-end movement,the smoother the riser shape,the smaller the bending deformation,not only to avoid the bending failure of the riser,but also to restore the riser as soon as possible to increase the efficiency of the re-entry process. There are three subfigures in Fig.5, respectively showing the simulation results of riser displacement over time under different currents of uniform, skewed, bilateral. There are 11 curves in each subfigure,and each curve presents the riser shape at a particular moment.The time interval between adjacent curves is determined by the movement of the surface vessel.In the first 30 s of the simulation time,the time interval is 10 s. In the ship’s uniform movement within 60 s, the time interval is 15 s.In the last 30 s,the time interval is 10 s.

    From Fig.5, we can see that there is a large difference of deformation between the upperend and lower-end of the riser. The movement of lower-end was visibly lagging behind that of upper-end. The reason of motion lag may be that the length of the flexible riser was too long and the dynamic effects of the surface vessel’s movement on the lower-end were relatively small. With the increase of water depth, this lag is more obvious. In addition, we found that, in the uniform current, the deformation trend of riser is very similar in the first 90 s, following gradually change of this trend. This phenomenon also appears in the results of the skewed current and the bilateral current,which explains the deceleration movement of the vessel has a relatively large impact on the deformation of the riser.

    Fig.5 Riser shape over time due to three simulated current profiles

    In uniform current (Fig.5a) and skewed (Fig.5b) current, the deformation trend of the riser is similar in the corresponding stage. In 0-90 s, with the increase of water depth, the left displacement of riser gets greater. And as time increases, the left displacement of the same position of the riser is also increasing. After 90 s, as the water depth increases, the riser offsets to the right first and then to the left.And as the time increases,the displacement of the same position of the riser is also increasing.In spite of these similarities,the deformation trend of the upper part of the riser is more pronounced and the bending degree is greater under the action of skewed current. However, in the bilateral current (Fig.5c), the deformation of the riser is more complicated. In the first 100 s, the shape of the riser presents‘S’. And in the first 80 s, as the time increases,‘S’shape gets more obvious. In 80 s-100 s, this trend is increasingly weakened.After 100 s,the‘S’shape of the riser completely fades away instead of a shape (offsets to the right first and then to the left) which is similar to that in the other two currents. Moreover,we found that,in the bilateral current,there is a greater displacement of the same position of riser than the other two currents, which is a result of the superposition of upper skewed current and lower skewed current.

    3.3 Lower-end motion

    In the re-entry operation of riser, the movement of the lower-end of the riser is more important,which directly affects the accuracy and efficiency of the re-entry process.When the upper-end of riser completes the displacement of 135 m within a specified time, the shorter the horizontal distance from the lower-end to the wellhead, the more favorable the re-entry operation of the riser. In this paper, the horizontal distance from the lower-end to the wellhead, the velocity and offset of the lower-end are analyzed and compared under three different currents respectively,as shown in Figs.6-8.

    According to Figs.6 and 7,it can be seen that the movement of the lower-end is very similar under uniform and skewed currents. In the acceleration phase of surface vessel, the velocity of the lower-end has been slowly raised and the lower-end only slowly moves a little toward the wellhead (uniform: about 10 m, skewed: about 5 m), which results from the initial state of riser and the motion lag of the lower-end of riser.At the stage of uniform motion of vessel (30~90 s),the lower-end moves quickly and steadily towards the wellhead. However, the inflection point of enhancing velocity of lower-end in uniform current predates obviously the time (as shown in Fig.7), and this is mainly because the lower-end subjects to the same current force as the upper-end in uniform current so that the velocity of lower-end increases faster. In addition, we can see the difference of the inflection point of the two distance curves in Fig.6.During the deceleration phase of vessel (90~120 s), the lower-end continues to move toward the wellhead with a reduced velocity,which is caused by the motion deceleration of surface vessel.Moreover,due to the motion lag of the lower-end, the inflection point time of starting to reduce velocity is >90 s(uniform:about 100 s,skewed:about 110 s).

    Fig.6 Distance changes

    Fig.7 Velocity changes

    Fig.8 Offset Changes

    We also found that the motion of the lower-end of riser is relatively complex due to the opposite effect in the upper and lower parts of the riser under bilateral currents.In the 30 s of accelerated motion, the lower-end moves away from the wellhead with the skewed current in the opposite direction although the upper-end moves toward the wellhead (as shown in Fig.6). The velocity of lower-end increases from 0 to 0.25 m/s,and then decreases to 0 m/s.At this point,it is just at uniform motion stage with the upper-end at a speed of 1.5 m/s.Since then,the lowerend begins to move toward the wellhead with a increasing speed.After 90 s,although the vessel has begun to slow down, there is still no significance for the lower-end to slow down under the effect of reverse current.

    In addition, we can see some of the more important information. At the same time, the distances between the lower-end and the wellhead are very different under different currents. The distance in the uniform current is the smallest which is only about 6 m at 120 s, and it is the largest in the bilateral current, which reaches 55 m at 120 s. But the velocity of lower-end is the largest in the uniform current,which reaches 1.1 m/s at 120 s,and it will cause a relatively large swing at the lower-end when the vessel stops moving above the wellhead, which is very detrimental to the re-entry operation. With these two considerations combined, we believe that the skewed current is relatively suitable for the re-entry operation.

    Finally, we study the offset of the lower-end to the upper-end of riser under the three currents, as shown in Fig.8. The bigger the offset, the bigger the bending degree of the riser, and the greater the bending stress on the riser,which is detrimental to the safety of the structure.By analyzing,we find a similar law for the offset of the lower-end under these currents.During the acceleration and uniform motion of the vessel, the offset at the lower-end increases with the time increased. At about 90 s, the vessel in deceleration phase, the offset curves present obvious inflection points. After that, the offset gradually reduces with the time increased. In addition, at the same time point, the offset of lower-end in bilateral current has always been relatively maximum, which reaches 70 m at 90 s. And at this time, the shape of riser is an obvious‘S’. In this case, it will cause not only relatively larger bending stress but also stronger shear stress in the middle of the riser, which is prone to cause the structure damage of riser. Therefore,we should try to avoid re-entry operation when there are bilateral currents.

    4 Conclusions

    Considering three different currents that may occur in real sea-conditions, an accurate model is provided to describe the dynamic behavior of risers in re-entry operation.The riser deformation (shape), horizontal distance from lower-end to wellhead and the velocity of lowerend were investigated under different currents (uniform, skewed and bilateral). Combining the horizontal distance of lower-end and the possible swings, we compared the effect of different currents on the re-entry operation, and some interesting and meaningful results were obtained that can offer references for precise and secure re-entry operation.

    (1) The deceleration movement of the surface vessel has a relatively large influence on the riser deformation. After 90 s of motion deceleration stage of vessel, the shape of riser gradually changes.

    (2)In uniform and skewed current,the deformation trend of the riser is similar in the corresponding stage. In 0-90 s, the left-displacement gets greater with the increase of water depth.After 90 s, the riser offsets to the right first and then to the left. However, in bilateral currents,the shape of riser shows a complicated‘S’.

    (3) Although the distance from lower-end to wellhead is the smallest in the uniform current, the velocity of lower-end is the largest, which may cause a large swing at the lower-end when the vessel stops moving above the wellhead. Considering the two aspects, we believe that the skewed current is relatively suitable for the re-entry operation compared with the other two currents.

    (4)The offset of lower-end to upper-end has always been relatively larger in bilateral currents,causing relatively larger bending stress and shear stress.The actual re-entry operation of riser should try to avoid the sea conditions with bilateral currents.

    国产精品国产三级专区第一集| 老女人水多毛片| 国产国拍精品亚洲av在线观看| 丰满人妻一区二区三区视频av| 日韩欧美精品v在线| 国产亚洲5aaaaa淫片| 久久99蜜桃精品久久| 亚洲成人av在线免费| 免费看光身美女| www.av在线官网国产| 日韩一区二区视频免费看| 亚洲在线自拍视频| 精品人妻一区二区三区麻豆| 乱系列少妇在线播放| 欧美激情在线99| av在线播放精品| 18禁在线无遮挡免费观看视频| 成人无遮挡网站| 男女视频在线观看网站免费| 高清日韩中文字幕在线| 久久精品久久久久久噜噜老黄 | 国产成年人精品一区二区| 亚洲精品色激情综合| 国产欧美另类精品又又久久亚洲欧美| 99久久中文字幕三级久久日本| 日本猛色少妇xxxxx猛交久久| 国产精品日韩av在线免费观看| 亚洲成人中文字幕在线播放| 亚洲av中文av极速乱| 天堂中文最新版在线下载 | 亚洲国产欧美人成| 99九九线精品视频在线观看视频| 最近中文字幕高清免费大全6| 美女内射精品一级片tv| 午夜精品在线福利| 欧美xxxx性猛交bbbb| 欧美xxxx性猛交bbbb| 嘟嘟电影网在线观看| 久久久久久久久久久丰满| 国产淫语在线视频| 国产午夜精品一二区理论片| 久久久久久久久久成人| 黄色一级大片看看| 在线天堂最新版资源| 国产高潮美女av| 日韩欧美精品v在线| 菩萨蛮人人尽说江南好唐韦庄 | 午夜免费激情av| 亚洲婷婷狠狠爱综合网| 亚洲高清免费不卡视频| 欧美色视频一区免费| 少妇熟女欧美另类| 99久久人妻综合| 亚洲丝袜综合中文字幕| 久久久久免费精品人妻一区二区| .国产精品久久| 两个人的视频大全免费| 久久99精品国语久久久| 日韩欧美精品v在线| 色吧在线观看| 色综合站精品国产| 91精品伊人久久大香线蕉| 乱系列少妇在线播放| 亚洲av不卡在线观看| 国产精品永久免费网站| 99久久精品一区二区三区| 国产精品人妻久久久久久| 白带黄色成豆腐渣| 九九在线视频观看精品| 亚洲精品亚洲一区二区| 国产一区二区在线观看日韩| 精品一区二区免费观看| 床上黄色一级片| 精品免费久久久久久久清纯| 久久午夜福利片| 在现免费观看毛片| 成人二区视频| 观看免费一级毛片| 中国美白少妇内射xxxbb| 国产老妇女一区| 日韩精品青青久久久久久| 少妇丰满av| 日韩欧美三级三区| 丰满乱子伦码专区| 亚洲国产精品成人综合色| 国产精品一区www在线观看| 晚上一个人看的免费电影| 国产免费又黄又爽又色| 中文资源天堂在线| 午夜福利在线观看免费完整高清在| 美女大奶头视频| 日韩欧美三级三区| 日本爱情动作片www.在线观看| 午夜免费激情av| 青春草国产在线视频| 精品人妻一区二区三区麻豆| 中国美白少妇内射xxxbb| 小说图片视频综合网站| 天天躁夜夜躁狠狠久久av| 久久99蜜桃精品久久| 国产精品一区二区三区四区久久| 丰满人妻一区二区三区视频av| 嫩草影院精品99| 性插视频无遮挡在线免费观看| 日韩欧美精品免费久久| 毛片女人毛片| 建设人人有责人人尽责人人享有的 | 全区人妻精品视频| 大话2 男鬼变身卡| 91午夜精品亚洲一区二区三区| 日韩一本色道免费dvd| 亚洲av中文av极速乱| 日韩精品有码人妻一区| 国产av在哪里看| 搡女人真爽免费视频火全软件| 国产亚洲91精品色在线| 麻豆国产97在线/欧美| 欧美一区二区亚洲| 在现免费观看毛片| 老司机影院成人| 禁无遮挡网站| 国产单亲对白刺激| 国产精品久久电影中文字幕| 久久人妻av系列| 国产又色又爽无遮挡免| 日韩一区二区视频免费看| 久久鲁丝午夜福利片| 欧美日韩一区二区视频在线观看视频在线 | av在线蜜桃| 欧美日本亚洲视频在线播放| www.色视频.com| 亚洲国产欧美人成| av卡一久久| 久久精品国产亚洲网站| 中文在线观看免费www的网站| 18+在线观看网站| 成人亚洲欧美一区二区av| 男人舔奶头视频| 亚洲精品乱久久久久久| av在线天堂中文字幕| 欧美xxxx黑人xx丫x性爽| 国产精品一区www在线观看| 国产91av在线免费观看| 国产色爽女视频免费观看| 91狼人影院| 亚洲国产高清在线一区二区三| av在线观看视频网站免费| eeuss影院久久| 色哟哟·www| 女人十人毛片免费观看3o分钟| 日本一二三区视频观看| 在线免费观看的www视频| 淫秽高清视频在线观看| 国模一区二区三区四区视频| 三级国产精品片| 老师上课跳d突然被开到最大视频| 久久久欧美国产精品| 欧美+日韩+精品| 你懂的网址亚洲精品在线观看 | 久久人人爽人人片av| 又黄又爽又刺激的免费视频.| 97超碰精品成人国产| 看十八女毛片水多多多| 欧美一区二区精品小视频在线| 久久国产乱子免费精品| 婷婷六月久久综合丁香| 我要看日韩黄色一级片| 国产成人a∨麻豆精品| 欧美xxxx性猛交bbbb| 国产大屁股一区二区在线视频| 欧美日本视频| 欧美三级亚洲精品| 2021天堂中文幕一二区在线观| 九九久久精品国产亚洲av麻豆| 国产精品精品国产色婷婷| 一区二区三区乱码不卡18| 国产亚洲精品久久久com| 五月玫瑰六月丁香| 国产熟女欧美一区二区| 国产亚洲一区二区精品| 亚洲精品色激情综合| 在线天堂最新版资源| 麻豆av噜噜一区二区三区| 国内精品宾馆在线| 九九爱精品视频在线观看| 18+在线观看网站| 亚洲国产高清在线一区二区三| 久久亚洲精品不卡| 免费大片18禁| 久久久久网色| 国产又黄又爽又无遮挡在线| 色综合色国产| 精品人妻视频免费看| 色哟哟·www| 久久久久网色| 久久久精品大字幕| 精品国产露脸久久av麻豆 | 九九在线视频观看精品| 最新中文字幕久久久久| 丰满乱子伦码专区| 99在线视频只有这里精品首页| 十八禁国产超污无遮挡网站| 人人妻人人澡人人爽人人夜夜 | 老司机影院毛片| 色噜噜av男人的天堂激情| 亚洲av电影在线观看一区二区三区 | 国产日韩欧美在线精品| 亚洲经典国产精华液单| 黄片wwwwww| 免费看美女性在线毛片视频| 欧美xxxx性猛交bbbb| 亚洲天堂国产精品一区在线| 国产毛片a区久久久久| 91aial.com中文字幕在线观看| 国国产精品蜜臀av免费| 国产精品熟女久久久久浪| 亚洲图色成人| 久久鲁丝午夜福利片| 哪个播放器可以免费观看大片| 在线观看美女被高潮喷水网站| 免费黄色在线免费观看| 亚洲丝袜综合中文字幕| 天堂中文最新版在线下载 | 91精品伊人久久大香线蕉| 日韩一区二区三区影片| av专区在线播放| 国产极品精品免费视频能看的| 久久99热这里只有精品18| 最近中文字幕高清免费大全6| 麻豆乱淫一区二区| 亚洲在线自拍视频| 全区人妻精品视频| 美女黄网站色视频| 精品久久久久久久末码| 国产av一区在线观看免费| .国产精品久久| 午夜a级毛片| 女人十人毛片免费观看3o分钟| 中文字幕制服av| 少妇熟女aⅴ在线视频| 久久99蜜桃精品久久| 国产精品女同一区二区软件| 中文字幕精品亚洲无线码一区| 99热精品在线国产| 国产高潮美女av| 在线免费观看的www视频| 久久久久九九精品影院| 中文字幕人妻熟人妻熟丝袜美| 三级男女做爰猛烈吃奶摸视频| 亚洲伊人久久精品综合 | 国产久久久一区二区三区| 国内精品一区二区在线观看| 亚洲欧美日韩无卡精品| 免费观看性生交大片5| 99久国产av精品| 欧美日韩国产亚洲二区| 日韩欧美精品v在线| 深爱激情五月婷婷| 国产精品久久久久久久久免| 欧美激情久久久久久爽电影| 97人妻精品一区二区三区麻豆| 亚洲av熟女| 久99久视频精品免费| 99热全是精品| 国产精品99久久久久久久久| 国产一区二区在线观看日韩| 91在线精品国自产拍蜜月| 中文字幕免费在线视频6| 国产白丝娇喘喷水9色精品| 在线观看一区二区三区| 一夜夜www| 国产精品一二三区在线看| 亚洲av中文字字幕乱码综合| 国产女主播在线喷水免费视频网站 | 大香蕉久久网| 26uuu在线亚洲综合色| 男女视频在线观看网站免费| 中文字幕制服av| av天堂中文字幕网| 99久久精品热视频| 一区二区三区乱码不卡18| 十八禁国产超污无遮挡网站| 欧美三级亚洲精品| 最近最新中文字幕免费大全7| 成人无遮挡网站| 亚洲av成人精品一区久久| 国产成人精品久久久久久| 日韩大片免费观看网站 | 日本三级黄在线观看| 老司机影院毛片| 国产私拍福利视频在线观看| 久久久久九九精品影院| 亚洲丝袜综合中文字幕| 日韩av不卡免费在线播放| 国产高清国产精品国产三级 | 丝袜喷水一区| 亚洲第一区二区三区不卡| 有码 亚洲区| 三级国产精品片| 久久鲁丝午夜福利片| 国产伦精品一区二区三区视频9| 一个人观看的视频www高清免费观看| 久久久久久久国产电影| 精品熟女少妇av免费看| 亚洲精品色激情综合| 麻豆精品久久久久久蜜桃| 免费av观看视频| 日韩中字成人| 国语对白做爰xxxⅹ性视频网站| 国产探花在线观看一区二区| 亚洲欧美精品自产自拍| 九九热线精品视视频播放| 一级av片app| 久久久久久久久久久免费av| 日日撸夜夜添| 国产精品一区www在线观看| 小蜜桃在线观看免费完整版高清| 免费看a级黄色片| 精品免费久久久久久久清纯| 亚洲精品一区蜜桃| 国产极品精品免费视频能看的| 综合色av麻豆| 久久人人爽人人片av| 九草在线视频观看| 美女国产视频在线观看| 亚洲成人久久爱视频| 97超碰精品成人国产| 成人国产麻豆网| 最近手机中文字幕大全| 麻豆一二三区av精品| 五月伊人婷婷丁香| 丝袜美腿在线中文| 色尼玛亚洲综合影院| 欧美日韩一区二区视频在线观看视频在线 | 最近最新中文字幕免费大全7| av女优亚洲男人天堂| 国产成人freesex在线| 久久99热这里只有精品18| 一本一本综合久久| 亚洲精华国产精华液的使用体验| 91午夜精品亚洲一区二区三区| 日韩成人av中文字幕在线观看| 国产精品久久电影中文字幕| 国产免费一级a男人的天堂| 国产视频首页在线观看| 午夜精品国产一区二区电影 | 免费大片18禁| 国产亚洲av片在线观看秒播厂 | 男女那种视频在线观看| 午夜福利高清视频| 午夜亚洲福利在线播放| 精品久久久久久久久久久久久| 中文天堂在线官网| 免费观看人在逋| 中文字幕人妻熟人妻熟丝袜美| 亚洲精品aⅴ在线观看| 观看美女的网站| 乱码一卡2卡4卡精品| 久久久久久九九精品二区国产| 嫩草影院新地址| 日本一本二区三区精品| 91午夜精品亚洲一区二区三区| 女人十人毛片免费观看3o分钟| 国产日韩欧美在线精品| 日产精品乱码卡一卡2卡三| 六月丁香七月| 亚洲丝袜综合中文字幕| 黄片wwwwww| 一二三四在线观看免费中文在 | av福利片在线| 高清欧美精品videossex| 中国美白少妇内射xxxbb| av片东京热男人的天堂| 国产亚洲一区二区精品| 欧美日韩综合久久久久久| 久久热在线av| 在线观看人妻少妇| 欧美日韩成人在线一区二区| 久久精品国产综合久久久 | 国产精品欧美亚洲77777| 国产欧美日韩一区二区三区在线| 满18在线观看网站| 午夜免费鲁丝| 丝袜喷水一区| 丝袜人妻中文字幕| 成人无遮挡网站| 另类亚洲欧美激情| 亚洲国产精品专区欧美| 亚洲五月色婷婷综合| 人体艺术视频欧美日本| 国产日韩一区二区三区精品不卡| 亚洲美女搞黄在线观看| 精品卡一卡二卡四卡免费| 久热这里只有精品99| 国产欧美日韩综合在线一区二区| 亚洲国产色片| 亚洲经典国产精华液单| 久久ye,这里只有精品| videos熟女内射| 黄片无遮挡物在线观看| 在现免费观看毛片| 黄色配什么色好看| 五月玫瑰六月丁香| 久久久久久人妻| 亚洲精品久久久久久婷婷小说| 一级毛片我不卡| 亚洲在久久综合| 免费久久久久久久精品成人欧美视频 | 国产精品一二三区在线看| 99视频精品全部免费 在线| 久久热在线av| 夜夜爽夜夜爽视频| 99热国产这里只有精品6| 亚洲国产精品成人久久小说| 久久精品人人爽人人爽视色| 一级片'在线观看视频| 成年av动漫网址| 超色免费av| 欧美国产精品va在线观看不卡| 看免费成人av毛片| 国产男人的电影天堂91| 九九爱精品视频在线观看| 一区二区三区精品91| 一本大道久久a久久精品| 久久精品国产亚洲av涩爱| 有码 亚洲区| 狠狠精品人妻久久久久久综合| 亚洲精品aⅴ在线观看| 好男人视频免费观看在线| 欧美+日韩+精品| 黑人猛操日本美女一级片| 老熟女久久久| 久久99精品国语久久久| 夜夜骑夜夜射夜夜干| 欧美+日韩+精品| 日韩av免费高清视频| 亚洲美女搞黄在线观看| 亚洲精品,欧美精品| 最近2019中文字幕mv第一页| 熟女电影av网| 天堂8中文在线网| 久久这里有精品视频免费| 色吧在线观看| 在线亚洲精品国产二区图片欧美| 日韩一本色道免费dvd| 又黄又粗又硬又大视频| 国产在线免费精品| 在线观看国产h片| 国产成人精品一,二区| 69精品国产乱码久久久| 精品一区二区三区视频在线| 国产精品一区二区在线观看99| 黄色怎么调成土黄色| 国产av一区二区精品久久| 中文精品一卡2卡3卡4更新| 国产精品久久久av美女十八| 99香蕉大伊视频| 久久99热6这里只有精品| 中文天堂在线官网| 婷婷色综合www| 人人妻人人澡人人爽人人夜夜| 欧美日韩视频高清一区二区三区二| 男女无遮挡免费网站观看| 日日撸夜夜添| 中文字幕亚洲精品专区| 欧美精品一区二区免费开放| 国产精品一区www在线观看| 全区人妻精品视频| 国产1区2区3区精品| 18+在线观看网站| 亚洲内射少妇av| 久久久久久人人人人人| 高清不卡的av网站| 久久精品国产亚洲av天美| 五月伊人婷婷丁香| 一边摸一边做爽爽视频免费| 中文字幕另类日韩欧美亚洲嫩草| 久久97久久精品| 欧美老熟妇乱子伦牲交| 日本猛色少妇xxxxx猛交久久| 亚洲欧美色中文字幕在线| 色婷婷av一区二区三区视频| 国产精品久久久久久精品古装| 一级,二级,三级黄色视频| av女优亚洲男人天堂| 永久网站在线| 美国免费a级毛片| 女人久久www免费人成看片| av国产精品久久久久影院| 人人妻人人爽人人添夜夜欢视频| 成人影院久久| 另类亚洲欧美激情| 精品久久国产蜜桃| 亚洲三级黄色毛片| 日韩大片免费观看网站| 纯流量卡能插随身wifi吗| 在线观看免费日韩欧美大片| 亚洲精品第二区| 日韩一本色道免费dvd| 国产老妇伦熟女老妇高清| 亚洲欧美一区二区三区黑人 | videossex国产| 大香蕉久久网| 91在线精品国自产拍蜜月| 熟女av电影| 青春草亚洲视频在线观看| 国产又爽黄色视频| 亚洲精品色激情综合| 新久久久久国产一级毛片| 亚洲综合色惰| av线在线观看网站| 久久久久精品久久久久真实原创| 亚洲国产成人一精品久久久| 国产精品偷伦视频观看了| 秋霞在线观看毛片| 亚洲av中文av极速乱| 秋霞在线观看毛片| 国产黄色免费在线视频| 99热6这里只有精品| 日韩一本色道免费dvd| 国产精品99久久99久久久不卡 | 亚洲伊人色综图| 最新中文字幕久久久久| 久久久久久久大尺度免费视频| 一区二区三区精品91| 99热这里只有是精品在线观看| 大香蕉久久成人网| 黄网站色视频无遮挡免费观看| 亚洲av国产av综合av卡| 在线观看www视频免费| 日本与韩国留学比较| 久久99热6这里只有精品| 大香蕉久久成人网| 亚洲av综合色区一区| 香蕉国产在线看| 晚上一个人看的免费电影| 成人国产麻豆网| 老熟女久久久| 99久久中文字幕三级久久日本| 国产高清三级在线| 色吧在线观看| 日本91视频免费播放| 十分钟在线观看高清视频www| 国产一区有黄有色的免费视频| 亚洲av.av天堂| 在线观看人妻少妇| 国产精品人妻久久久影院| 巨乳人妻的诱惑在线观看| 国产国拍精品亚洲av在线观看| 秋霞伦理黄片| 国产在线免费精品| 啦啦啦中文免费视频观看日本| 国产欧美亚洲国产| 精品卡一卡二卡四卡免费| 香蕉丝袜av| 大香蕉97超碰在线| 日本免费在线观看一区| 欧美国产精品va在线观看不卡| 22中文网久久字幕| 韩国高清视频一区二区三区| 国产精品无大码| 亚洲精品456在线播放app| 26uuu在线亚洲综合色| 韩国精品一区二区三区 | 极品少妇高潮喷水抽搐| 少妇人妻久久综合中文| 一级爰片在线观看| 国产亚洲午夜精品一区二区久久| 亚洲欧美成人精品一区二区| 欧美日韩视频高清一区二区三区二| 少妇高潮的动态图| 日韩欧美精品免费久久| 日本黄大片高清| 九色亚洲精品在线播放| 亚洲精品,欧美精品| 国产欧美日韩一区二区三区在线| 亚洲美女视频黄频| 成年av动漫网址| 国产成人免费观看mmmm| 免费少妇av软件| 亚洲欧洲日产国产| kizo精华| 中文字幕av电影在线播放| 亚洲成人av在线免费| 国产精品嫩草影院av在线观看| 1024视频免费在线观看| 999精品在线视频| 日韩制服骚丝袜av| 一级爰片在线观看| 国产精品三级大全| 欧美激情 高清一区二区三区| 亚洲 欧美一区二区三区| 国产白丝娇喘喷水9色精品| 最近手机中文字幕大全| 国产女主播在线喷水免费视频网站| 三级国产精品片| 久久久久精品久久久久真实原创| tube8黄色片| 国产亚洲最大av| 深夜精品福利| 好男人视频免费观看在线| 天堂中文最新版在线下载| 狂野欧美激情性bbbbbb| 欧美日韩视频精品一区| 久久精品国产a三级三级三级| 亚洲精品色激情综合| 国产av一区二区精品久久| 欧美日韩视频高清一区二区三区二| 国产白丝娇喘喷水9色精品| 又黄又粗又硬又大视频| 亚洲精品日韩在线中文字幕| 亚洲国产欧美日韩在线播放| 国产成人免费观看mmmm| 欧美变态另类bdsm刘玥| 久久精品久久精品一区二区三区|