• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Influence of shaped charge structure parameters on the formation of linear explosively formed projectiles

    2022-10-17 03:45:48TianbaoMaJingLiuQiWang
    Defence Technology 2022年10期

    Tian-bao Ma,Jing Liu,Qi Wang

    State Key Laboratory of Explosion Science and Technology,Beijing Institute of Technology,Beijing,100081,China

    Keywords:LEFP Numerical simulation Shaped charge Structure optimization

    ABSTRACT The research of LEFP (linear explosive forming projectile) is of great value to the development of new warhead due to its excellent performance.To further improve the damage ability of the shaped charge warhead,a special shell overhanging structure was designed to increase the charge based on the traditional spherical charge,in which case the crushing energy of LEFP could be guaranteed.LS-DYNA was used to simulate different charge structures obtained by changing the number of detonation points,the length of shell platform,the radius of curvature and the thickness of liner.The RSM(response surface model) between the molding parameters of LEFP and the structural parameters of charge was established.Based on RSM model,the structure of shaped charge was optimized by using multi-objective genetic algorithm.Meanwhile,the formation process of jet was analyzed by pulsed X-ray photography.The results show that the velocity,length-diameter ratio and specific kinetic energy of the LEFP were closely related to the structural parameters of the shaped charge.After the optimization of charge structure,the forming effect and penetration ability of LEPP had been significantly improved.The experimental data of jet velocity and length were consistent with the numerical results,which verifies the reliability of the numerical results.

    1.Introduction

    With the improvement of the protection capabilities of modern military equipment,traditional shaped charges are facing great challenges.In the field of active protection,a new type of shaped energy warhead named linear explosively formed projectiles(LEFP)have been proposed in recent years,which is developed on the basis of traditional Explosively Formed Projectile (EFP).Compared with traditional EFP,it has higher speed,quality and hit rate.

    Payman[1] first proposed a structure similar to EFP in 1935.At the end of the 20th century,EFP was widely concerned by researchers [2-4].The study found that the shape of the EFP was main affected by the shape and material of the liner,the type and detonation method of the explosive,the structure and geometric parameters of the shaped charge.Weickert[5]studied the process of seven different shapes of liner penetrating targets of different materials,and found that the penetration ability of EFP was greatly affected by the shape of the liner.Houman[6]used a shape function with a correction term to optimize the shape of the EFP,the measured speed and profile of EFP were in good agreement with the optimization results.In addition,Jacek [7] compared the formation process of the EFP with conical charge and spherical charge,and the experiments of penetrating steel target were carried out.Pappu [8] and Zhu [9] used AUTODYN to study the residual microstructure characteristics and geometric parameters of EFP formed by liner in different materials.They found that tantalum material is more conducive to the formation of EFP.While Wu[10],Hu[11,12]and Zaki[13]studied the influence of different explosive materials and liner shapes on the penetration capability of EFP,the best combination of liner and explosive was obtained.Meanwhile,Li [14] found that annular multi-point initiation was more conducive to the improvement of EFP&apos;s penetration ability,but the multipoint synchronized initiation deviation needed to be less than 200 μs.In terms of the structure of shaped charge,the penetration performance of EFP was mainly improved by connecting two liners in series [15] or multi-stage ammunition [16].

    In order to further enhance the penetration capability of projectile,scholars were committed to exploring new shaped charge warhead.Literature [17-19] proposed an appropriate model to study the dynamic response of structure driven by explosion from a theoretical perspective.Liu [20] conducted penetration tests of a new type of multi-explosively formed projectile warhead (MEFP)with seven arc-cone liners against 45#steel target.In addition,the influence of the structural parameters of MEFP warhead on the formation of EFPs was studied in literature [21].Bohanek [22]determined the effects of different qualities and materials of explosive on the penetration ability of LEFP through experiments.Cheng[23]designed a new bi-apex-angle linear shaped charge,the effects of different liner thickness and explosive type on jet penetration performance were studied.

    Ning [24] and Ma [25] proposed a special evolvable warhead structure as illustrated in Fig.1.This evolvable warhead was symmetrical and consists of four similar parts,which would be expanded under explosion loading and the fragments with a directional distribution were generated to increase the damage effect.To further enhance the penetration performance to thicker targets,a linear shaped charge warhead was proposed in this paper based on the reference [25].The forming process of LEFP was numerically simulated by LS-DYNA,and the influence of initiation method,the length of shell platform,the radius of curvature and the thickness of the liner on the forming of LEFP were analyzed.Moreover,an optimization scheme was designed to optimize the geometric parameters of the shaped charge to improve the penetration ability of LEFP.This will have a certain impetus for future research on LEFP.

    2.Material model and parameters

    2.1.The calculation model

    In this paper,the forming of LEFP and penetration into the target were studied.The calculation model consists of four parts: shell,explosive,liner and air.The structure of shaped charge is shown in Fig.2.

    The appearance of the shaped charge designed is cylindrical,with a diameter of 20 cm and a height of 30 cm.Four identical linear liners are symmetrically distributed around.The linear liner is divided into 10 segments,the outermost two segments have a height of 2.0 cm,the middle eight segments have a height of 3.0 cm,and the cover have a thickness of 1.0 cm.Due to the symmetry of the structure,a quarter model is used for calculation.The size of the air domain,meanwhile,is 200 mm × 400 mm × 550 mm with continuous boundary condition.Fig.3 shows the internal structure of the model.The structure is composed of shell,cover,explosive and a liner.Where L is the length of shell platform,and δ are the radius of curvature and thickness of the liner,respectively.

    Fig.1.The structure of evolvable warhead.

    Fig.2.The structure of shaped charge.

    Fig.3.The internal structure of the model.

    The calculation model was simulated by LS-DYNA software.The grid size of the shell and air is 1.5 mm,while the liner and explosive are 1.0 mm.The numerical Algorithm is ALE(Arbitrary Lagrangian-Eulerian),in which the shell and liner are Lagrangian grids,explosive and air are Euler grids.

    2.2.Material model and parameters

    The materials of the shell,liner and target involved in this paper are aluminum,copper and 45# steel.They are modeled by the Johnson-Cook material model which is widely used in the research of penetration.The yield stress σis defined as:

    To describe the material at a high strain rate,the equation of state of Gruneisen is used in the above three parts.The pressureis defined as:

    where ρis the initial density.is the intercept of the v-vcurve.,andare the coefficients of the slope of the v-vcurve where vand vare shock-velocity and particle-velocity,respectively.γis the Gruneisen gamma.The first order volume correction for γis.And μ =ρ/ρ-1.represents internal energy.

    Explosive studied in this paper is Comp-B,high-energy material model and JWL equation of state are adopted,in which the pressureis expressed as:

    where,,,and ω are parameters related to the explosive.is the specific volume.is the specific internal energy.

    Numerical computation is carried out in the air domain,and the equation of state of air is Linear-Polynomial.The pressis given by:

    where,…are the coefficients of polynomial equation.μ =ρ/ρ-1,and ρ/ρis the ratio of current density to initial density.is the internal energy.

    The material parameters of copper and aluminum are determined by separate Hopkinson pressure bar (SPHB) experiments,the parameters of different material models are listed in Table 1.

    2.3.Numerical algorithm and experimental verification of shaped charge jet

    (a) The model of shaped charge jet

    The calculation model is shown in Fig.4,where the explosive is Comp-B,the length of the charge is 110 mm,the diameter is 60 mm.The thickness of the liner is 2.4 mm,with a diameter of 60 mm,with a conical angle of 60.Numerical calculations are carried out in the air domain.The calculation domain is cylindrical with a length of 280 mm,and its diameter is 100 mm.The axis of the explosive and the liner is the same as the calculation domain due to the symmetry of the model.

    LS-DYNA was used for numerical calculation,the calculation method was ALE,in which the liner was Lagrangian grid,the explosive and air were Euler grid.The size of the Lagrangian grid is 0.3 mm,while the Euler grid is 0.4 mm.Such grid size could ensure the accuracy of calculation effectively.

    Fig.4.3D structure of shaped charge jet.

    Fig.5.The jet of shaped charge.

    To ensure the reliability of numerical results,the experiment of jet flow was carried out.Pulsed X-ray photography could measure the process of high-speed movement,which was widely used in explosion experiments.It was used to observe the formation process of the jet,obtain the velocity of the jet tip and measure the length of the jet.Both experiment and numerical calculation were single-point initiation,and which was located in the center of the end face of the explosive.In experiments and numerical calculations,it could be clearly seen that the liner was crushed by the detonation products,and finally a pestle body and a metal jet were formed.At=26 μs and=42 μs,the images taken by pulse X-ray photography were shown in Fig.5(a),and the numerical results were shown in Fig.5(b).The results data were listed in Table 2.

    Table 1 Parameters of each material.

    Table 2 Material model in the table.

    Analyzing the data in the table,the error of the jet length was 1.0%when=26 μs,which was 1.4%when=42 μs.The error forboth the diameter of the jet and the velocity of the jet tip was less than 6.0%.When the jet becomes stable,the shape of the jet was in good agreement with the experimental result.This showed that the numerical method was very effective for the simulation of the jet and could be used to simulate the experimental results.

    3.Numerical simulations on the forming of LEFP

    3.1.Analysis of the formation process of LEFP

    Numerical results showed that in the process of being crushed of the 10-segment liner,the two segments at the edge with a large scattering angle had poor forming effect as shown in Fig.6.The eight segments at the middle had better forming effect,especially the two segments in the middle.On the basic of this,the middle two segments were used to be analyzed.

    Fig.6.The forming of LEFP: (a) R =10 cm,δ =4.5 mm, L =3 cm;(b) R =10 cm,δ =4 mm, L =3 cm.

    The forming process and the overall velocity curve of the intermediate EFP were shown in Fig.7 and Fig.8.The crushing,overturn and closing of EFP could be clearly seen in Fig.7.About=170 μs,the shape of LEFP had been stabilized,and then it kept the same shape to fly.From Fig.8,the velocity increased dramatically in the first 20 μs,and then it flattened out in the next 80 μs.The curve tended to stabilize after 80 μs which suggested that the velocity reached a stable value.

    The control variable method was used to design the structure parameters of the shaped charge and the number of detonation points.The stable velocity (),the specific kinetic energy () and the length-diameter ratio(=/)of LEFP were used as indicators to assess penetration ability.The stable velocityrefers to the subsequent stable value of the velocity curve in Fig.8,and the specific kinetic energy=/,whereis the kinetic energy of EFP andis the projected area in the flight direction of the EFP.Fig.9 was a schematic diagram of the definition of parametersand.

    3.2.The influence of the number of detonation points on LEFP molding

    The model=10 cm,δ =4.5 mm,=3 cm was selected,and six groups of samples with the number of detonation pointsranging from 3 to 8 were designed.When=200 μs,in which moment the LEFP had been formed stable,the curves of velocity,specific kinetic energy and the length-diameter ratio varying with the number of detonation points were obtained,as illustrated in Fig.10.

    According to Fig.10,it could be found that as the number of detonation pointsincreases,the velocity and specific kinetic energy of LEFP had a little change.They had a small growth when the number of detonation points increased from 3 to 4,and then the curves flattened out.The length-diameter ratio of LEFP increased slowly when the number of detonation points was no more than 6,while increased obviously whenexceeded 6.The results showed that with the increase of the detonation points,it was close to the line detonation,the impact of the detonation wave on the liner was more balanced.This led to the liner being crushed better,which led to a better molding effect of the LEFP.

    3.3.The influence of the length of shell platform on LEFP molding

    Choosing L =2.0,2.125,2.25,2.375,2.5,2.625,2.75 and 3.0 cm when=10 cm,δ =4.5 mm and=8,eight groups of samples were designed.The curves of velocity,specific kinetic energy and the length-diameter ratio varying with the length of shell platform were obtained at=200 μs,as shown in Fig.11.

    According to Fig.11,asincreased from 2.0 cm to 3.0 cm,the velocity of LEFP increased steadily,with an increase of 17.9 %.Nevertheless,the specific kinetic energy fluctuated around 40 kJ/cm.The reason was that with the increase of,the mass of the explosive also increased,which led to a certain increase in the velocity.Due to the particularity of the structure,the mass of the liner will decrease,and there was little difference in the kinetic energy of the LEFP,which led to a small increase in the specific kinetic energy.Before L reaches 2.5 cm,the length-diameter ratio decreased with the increase of,and then it fluctuated around 2.9 asincreased.It could be seen from No.7-14 in Table 3,when2.5 cm,the shape of LEFP was long,while≥2.5 cm,the length of LEFP was close to the same.When L is less than 2.5 cm,the velocity of LEFP was small although the length-diameter ratio was large.In comparison,the molding of LEFP was better whenwas around 3.0 cm.

    Fig.7.The forming process of LEFP: (a) R =15 cm,δ =4.5 mm, L =3 cm;(b) R =10 cm,δ =4.5 mm, L =3 cm.

    Fig.8.The velocity curve of LEFP in model R =10 cm,δ =4.5 mm,L =3 cm.

    Fig.9.Definition of parameters of LEFP.

    3.4.The influence of the radius of curvature of the liner on LEFP molding

    Ten calculation examples were designed with=5,7.5,10,12.5,15,17.5,20,22.5,25 and 30 cm when δ =4.5 mm,=3 cm and=8.The velocity,specific kinetic energy,and length-diameter ratio curves with the radius of curvature of the liner were obtained when=200 μs,as shown in Fig.12.

    From Fig.12,as the radius of curvatureof the liner increased,the velocity increased significantly and specific kinetic energy of LEFP went up and then it went down.Whenincreased from 5 cm to 10 cm,the velocity increased greatly,and then it tended to be flat whenreached 10 cm.The specific kinetic energy reached its maximum whenwas around 10 cm.The length-diameter ratio decreased as the radius of curvature of the liner increased.As can be seen from No.15-24 in Table 3,with the increased of,the bending of the liner decreased as same as being stretched.Therefore,the length of the LEFP was shorter and the thickness was larger,which was not conducive to the penetration of the LEFP.It could be found that when the radius of curvature of the liner was around 10 cm,it was beneficial to improve the penetration ability of LEFP.

    Fig.10.The curves of v, ek and i varying with n.

    Fig.11.The curves of v, ek and i varying with L.

    3.5.The influence of the thickness of the liner on LEFP molding

    Nine numerical examples of δ =3.5,3.75,4.0,4.25,4.5,4.75,5.0,5.25 and 5.5 mm were selected when=10 cm,=3 cm and=8.The curves of the velocity and specific kinetic energy and length-diameter ratio varied with the thickness of the liner(δ)was obtained at=200 μs as Fig.13.

    From the analysis in Fig.13,the mass of the liner increased with the thickness of the liner increased,which led to a significant downward trend in the velocity and specific kinetic energy of LEFP.During the change of δ from 3.5 mm to 5.5 mm,the velocity decreased from 2371.8 m/s to 1761.3 m/s and the specific kinetic energy of LEFP reduced from 64.17 kJ/cmto 34.76 kJ/cm,which was adverse to the penetration of LEFP.The length-diameter ratio of LEFP first increased and then decreased with the increase of δ,reaching the maximum value when δ was near 4.5 mm.According to No.25-32 in Table 3,it was found that when δ was around 4.5 mm,the shape of LEFP was longer and thinner.For comprehensive comparison,it was good for the formation of LEFP when δ was in the vicinity of 4.5 mm.

    3.6.Analysis and discussion of numerical simulation results

    Analyzing the above numerical calculation results and combined with the final molding effect of middle EFP as shown in Table 3,it could be concluded that when=10 cm,δ =0.45 cm,=3.0 cm and=8,the molding effect of the LEFP were optimal.Meanwhile,it had a higher velocity,a relatively large specific kinetic energy and length-diameter ratio.

    4.Structural parameter optimization design

    4.1.Establishment of response surface model

    According to the numerical results,the number of initiating points was kept at 8.In order to obtain a more accurate mathematical model,10 additional points created by Optimal Latin-Hypercube Design [26,27] were added to build the model.The length of shell platform,the radius of curvatureand the thickness δ of the liner were regarded as input variables.Based on the numerical results in the previous section,the range of input variables was further refined as Table 4.The middle LEFP was used for analysis,and the numerical results of the increased sample points were shown in Table 5.

    Table 3 Forming results of LEFP.

    Table 3 (continued)

    Table 4 Design scope of parameters.

    Table 5 The numerical simulation results.

    Correspondingly,the velocity,specific kinetic energy and length-diameter ratio of the LEFP were regarded as output variables.Third-order response surface models of three output variables with respect to input variables were established by Matlab software as Eqs.(5)-(7).This method used polynomials to fit the sample points,which was more accurate in the local scope and simple to calculate.

    4.2.Error analysis of the model

    There are three indicators for evaluating model accuracy: Coefficient of Multiple Correlation (),Relative Average Absolute Error () and Relative Maximum Absolute Error ().They are expressed as equations 8-11:

    Fig.12.The curves of v, ek and i varying with R.

    Fig.13.The curves of v, ek and i varying with δ.

    ,andare used to jointly evaluate the accuracy of the model.andevaluate the accuracy of the model globally,andevaluates the accuracy of the model locally.The closeris to 1,the smaller the value ofand,and the more accurate the model is.The reference ranges of,andare 0.9-1,0 to 0.2,and 0 to 0.3 respectively.Five points were randomly selected for error analysis of the model,and the error was shown in Table 6.

    To further verify the accuracy of the model,a test point far from the center of the sample were selected for numerical simulation.The test point was=10 cm,δ =0.35 cm,=2.5 cm.The numerical results and calculation results were shown in Table 7.

    It could be found from Table 7 that the model calculation results were in good agreement with the numerical results,and the mathematical model could reflect the numerical simulation results very well.

    4.3.Optimization scheme design

    Sequential Quadratic Programming (NLPQL) [28,29] is an algorithm widely used in optimization design.It expands the objective function with a second-order Taylor series,and linearizes the constraints.The original nonlinear problem is transformed into a quadratic programming problem,and this algorithm is very stable.The mathematical model is as

    whereand()are input and output variables,andare the numbers of them.()and()are equality constraints andinequality constraints,andare the numbers of them.andindicate the lower and upper bounds of the input variable as listed in Table 4.The input variablein this paper were the length of shell platform,the radius of curvatureand the thickness δ of the liner,and the output variable()were the velocity,specific kinetic energyand length-diameter ratioof EFP.Inequality constraints()were applied in optimization scheme,and()were designed as≥2000 m/s,≥50 kJ/cm,and≥3.5.

    Table 6 The error analysis.

    Table 7 The test point results.

    Table 8 The results before and after optimization.

    Fig.14.Optimization process.

    Based on iSight software,the sequential quadratic programming method was carried out in this paper for iterative optimization,the number of iteration steps was set to 100.The length-diameter ratio and specific kinetic energy became the main optimization goal,and the velocity became the auxiliary optimization goals by assigning weighting coefficients.The structure parameters of the shaped charge based on the maximum value of the objective function were obtained.The process was shown in Fig.14.The initial parameter was=10 cm,δ =4.5 mm,=3.0 cm.The optimized result was=11.75 cm,δ =3.66 mm,=2.0 cm.

    Fig.15.Forming of LEFP before and after optimization: (a) Before optimization;(b) After optimization.

    Fig.16.The effect of penetration.

    4.4.Numerical simulation results of penetrating steel target

    Numerical simulation of the optimized model was compared with the initial model.Analysis of intermediate EFP found that the velocity,kinetic energy and length-diameter ratio of LEFP had been greatly improved.The forming process of LEFP before and after optimization was shown in Fig.15,and Table 8 showed the numerical results.

    It could be seen from Fig.15 that the optimized liner was crushed by the detonation product and turned faster,which was more conducive to the formation of LEFP with a large lengthdiameter ratio.It also could be found from Table 6 that compared with initial model,the length-diameter ratio of LEFP had increased by 77.55 % after optimization,and the velocity and specific kinetic energy had also increased by 2.5%and 49.86%,respectively.Which was due to the large length-diameter ratio and specific kinetic energy as the main optimization goal.

    Fig.17.The residual velocity of LEFP.

    Table 9 The results before and after optimization.

    Based on the results before and after optimization,the process of penetrating the steel target with a thickness of 3 cm was simulated.The penetration effect of the middle EFP was shown in Fig.16.

    Fig.16 illustrated the length-diameter ratio of LEFP was relatively small before optimization,and the pits of the target were large,which was caused by the serious deformation of LEFP during the penetration.After optimization,the length-diameter ratio of LEFP increased,the deformation of the LEFP decreased during the penetration,and the target had smaller pits,which ensured the remaining penetration capability of the LEFP.

    The fragments of the LEFP were collected for residual velocity analysis as shown in Fig.17.Where vand vwere the velocities before and after optimization.It could be concluded that the decay time of vwas shorter than v,which indicated that the penetration process took less time and retained a higher residual velocity after optimization.

    The data of velocity decay was listed in Table 9.Analysis of Table 9 showed that compared with before optimization,the absolute velocity decay of LEFP was reduced by 190 m/s,the relative velocity decay was reduced by 10.86 % after optimization.The penetration ability of LEFP had been greatly improved.

    5.Conclusion

    In this paper,a series of numerical simulations on shaped charges of different structural sizes were carried out by using LSDYNA.The RSM of the velocity,the kinetic energy and the lengthdiameter ratio of LEFP with respect to the number of detonation points,the length of shell platform,the radius of curvature and the thickness of the liner were obtained.An optimization method was designed to optimize the better model.The main conclusions are as follows:

    (1) Compared with the pulse X-ray experiment,the numerical results were in good agreement with the experimental results.The numerical simulation results can be used to approximate the experimental results within a certain range.

    (2) Analysis of numerical simulation results,when the number of initiation points is more than six,it has little effect on the forming of LEFP.Within the scope of the research,the velocityand specific kinetic energyof LEFP increase with the length of shell platformincreases,and decrease with the increase of the thickness of the liner δAs the radius of curvatureof the liner increases,the velocity increases but the specific kinetic energy increases first and then decreases.The length-diameter ratiodecreases whenandincrease,it increases first and then decreases with the increase of δWhen L exceeds a certain value,the length-diameter ratio tends to be stable.

    (3) The sequential quadratic programming method is used to optimize the established third-order response surface model,and accurate result is obtained.Numerical simulations of penetrating steel target are carried out before and after optimization.The results show that the velocity,specific kinetic energy and length-diameter ratio of LEFP have improved,especially the specific kinetic energy and lengthdiameter ratio have increased greatly.Based on the analysis of the residual velocity of fragments,both the absolute velocity decay and relative velocity decay of the optimized LEFP are reduced,which is conducive to the improvement of the penetration performance of the LEFP.It illustrates the reliability of the optimization method.

    The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

    This work was supported by the National Natural Science Foundation of China (Grant No.11772061).

    久久久久精品国产欧美久久久| 国产亚洲av高清不卡| 亚洲中文字幕日韩| 国内揄拍国产精品人妻在线| 听说在线观看完整版免费高清| 黄片大片在线免费观看| 成年女人毛片免费观看观看9| 亚洲精品av麻豆狂野| 成年版毛片免费区| 亚洲成人精品中文字幕电影| 99国产综合亚洲精品| 最近在线观看免费完整版| 熟女少妇亚洲综合色aaa.| 黄色毛片三级朝国网站| 欧美成人午夜精品| 在线永久观看黄色视频| 久久天躁狠狠躁夜夜2o2o| 国产精品亚洲av一区麻豆| 日本一本二区三区精品| 在线观看免费视频日本深夜| 久久婷婷人人爽人人干人人爱| 丝袜美腿诱惑在线| 又爽又黄无遮挡网站| 一区二区三区国产精品乱码| 男人舔女人的私密视频| 欧美性猛交黑人性爽| 欧美成狂野欧美在线观看| svipshipincom国产片| 日韩国内少妇激情av| 老司机靠b影院| 国产欧美日韩一区二区三| 99久久无色码亚洲精品果冻| 亚洲第一电影网av| 黑人巨大精品欧美一区二区mp4| 国产野战对白在线观看| 51午夜福利影视在线观看| 亚洲欧美激情综合另类| 欧美 亚洲 国产 日韩一| ponron亚洲| 亚洲国产看品久久| 久久精品国产亚洲av香蕉五月| 免费在线观看完整版高清| 欧美一区二区国产精品久久精品 | 一个人免费在线观看的高清视频| 一夜夜www| 欧美成人一区二区免费高清观看 | 女警被强在线播放| 中出人妻视频一区二区| 黄色a级毛片大全视频| 亚洲午夜理论影院| 国产精品一区二区精品视频观看| 少妇粗大呻吟视频| 亚洲成人精品中文字幕电影| 欧美黑人巨大hd| 国产久久久一区二区三区| 岛国在线观看网站| 国产精品一及| 国产熟女午夜一区二区三区| 精品国内亚洲2022精品成人| 欧美精品啪啪一区二区三区| 国产精品98久久久久久宅男小说| 不卡一级毛片| 国内少妇人妻偷人精品xxx网站 | 三级男女做爰猛烈吃奶摸视频| 看黄色毛片网站| 国产亚洲欧美98| 首页视频小说图片口味搜索| 亚洲天堂国产精品一区在线| 日韩欧美在线乱码| 黄色成人免费大全| 男人舔女人的私密视频| 久久99热这里只有精品18| 色综合站精品国产| 亚洲黑人精品在线| 麻豆成人午夜福利视频| 中出人妻视频一区二区| 亚洲精品av麻豆狂野| 国语自产精品视频在线第100页| 精品国产超薄肉色丝袜足j| 精品乱码久久久久久99久播| 久99久视频精品免费| 亚洲av片天天在线观看| 亚洲美女黄片视频| cao死你这个sao货| 久久国产精品人妻蜜桃| 国产精品久久久久久久电影 | 亚洲成人中文字幕在线播放| 又大又爽又粗| 精品国产乱子伦一区二区三区| 三级国产精品欧美在线观看 | 国产麻豆成人av免费视频| 9191精品国产免费久久| 精品久久久久久,| 亚洲精品美女久久久久99蜜臀| 久久九九热精品免费| 午夜精品一区二区三区免费看| 色哟哟哟哟哟哟| 久久久水蜜桃国产精品网| 午夜老司机福利片| 天天一区二区日本电影三级| 国产精品香港三级国产av潘金莲| 久久久久九九精品影院| 国产亚洲精品av在线| 2021天堂中文幕一二区在线观| 久久人妻福利社区极品人妻图片| √禁漫天堂资源中文www| 国产精品99久久99久久久不卡| 他把我摸到了高潮在线观看| 麻豆成人午夜福利视频| 天天一区二区日本电影三级| 宅男免费午夜| 在线观看免费午夜福利视频| 搡老熟女国产l中国老女人| 日韩欧美精品v在线| 精品免费久久久久久久清纯| 久久午夜综合久久蜜桃| 日本免费一区二区三区高清不卡| 欧美成人性av电影在线观看| 夜夜躁狠狠躁天天躁| 此物有八面人人有两片| 丝袜美腿诱惑在线| 黑人欧美特级aaaaaa片| 女人高潮潮喷娇喘18禁视频| 国产高清有码在线观看视频 | 午夜福利在线在线| 母亲3免费完整高清在线观看| 日本在线视频免费播放| 欧美高清成人免费视频www| 18禁观看日本| 老汉色av国产亚洲站长工具| 18禁裸乳无遮挡免费网站照片| 亚洲人成网站高清观看| 国产精品综合久久久久久久免费| 天天添夜夜摸| 黄色丝袜av网址大全| 欧美日韩黄片免| 久久精品综合一区二区三区| 欧美另类亚洲清纯唯美| 伊人久久大香线蕉亚洲五| 91av网站免费观看| xxx96com| 午夜影院日韩av| 精品久久久久久久末码| 男男h啪啪无遮挡| 天天躁狠狠躁夜夜躁狠狠躁| 高清毛片免费观看视频网站| 黑人操中国人逼视频| 国产一区在线观看成人免费| 毛片女人毛片| 国产精品亚洲美女久久久| 日韩 欧美 亚洲 中文字幕| 久久精品91无色码中文字幕| 一区二区三区国产精品乱码| 午夜福利欧美成人| 国产av又大| 香蕉久久夜色| 国产精品,欧美在线| 麻豆成人午夜福利视频| 午夜激情av网站| 国产av不卡久久| av片东京热男人的天堂| 国产亚洲av高清不卡| 色噜噜av男人的天堂激情| 国产成人影院久久av| 国产精品电影一区二区三区| 亚洲精品久久成人aⅴ小说| 在线观看免费日韩欧美大片| 日本熟妇午夜| 床上黄色一级片| 国产69精品久久久久777片 | 99热只有精品国产| 中出人妻视频一区二区| 色哟哟哟哟哟哟| 日韩欧美免费精品| 国产又黄又爽又无遮挡在线| 婷婷精品国产亚洲av在线| 99久久无色码亚洲精品果冻| netflix在线观看网站| 国产精品香港三级国产av潘金莲| 精品一区二区三区四区五区乱码| 国产精品一区二区精品视频观看| 亚洲中文av在线| 一卡2卡三卡四卡精品乱码亚洲| 午夜两性在线视频| 日本免费a在线| 天堂影院成人在线观看| 搡老岳熟女国产| 午夜福利视频1000在线观看| 欧美性长视频在线观看| 波多野结衣高清作品| 夜夜夜夜夜久久久久| 亚洲精品一卡2卡三卡4卡5卡| 国产av不卡久久| 久久久久国产一级毛片高清牌| 午夜两性在线视频| 国产黄色小视频在线观看| 黄色丝袜av网址大全| 神马国产精品三级电影在线观看 | 国产高清视频在线播放一区| 久久精品国产亚洲av高清一级| 两个人看的免费小视频| 国产男靠女视频免费网站| av超薄肉色丝袜交足视频| 成人一区二区视频在线观看| 成人三级黄色视频| 亚洲国产欧美一区二区综合| 国产成人一区二区三区免费视频网站| 国产又黄又爽又无遮挡在线| 亚洲欧美日韩东京热| 大型黄色视频在线免费观看| 黄片小视频在线播放| 欧美成狂野欧美在线观看| 日韩有码中文字幕| 成年女人毛片免费观看观看9| 久久精品国产综合久久久| 妹子高潮喷水视频| 黄片小视频在线播放| 亚洲五月婷婷丁香| 最近最新中文字幕大全电影3| 中文亚洲av片在线观看爽| 99精品欧美一区二区三区四区| av超薄肉色丝袜交足视频| svipshipincom国产片| 亚洲精品一卡2卡三卡4卡5卡| 男人舔女人下体高潮全视频| 69av精品久久久久久| 人妻久久中文字幕网| 在线十欧美十亚洲十日本专区| 啦啦啦免费观看视频1| 免费观看人在逋| 热99re8久久精品国产| 白带黄色成豆腐渣| 国产精品av久久久久免费| 国产在线精品亚洲第一网站| 亚洲精品久久成人aⅴ小说| 热99re8久久精品国产| 亚洲午夜理论影院| 999久久久国产精品视频| 国产精品1区2区在线观看.| 中出人妻视频一区二区| 全区人妻精品视频| 两个人免费观看高清视频| 男插女下体视频免费在线播放| 人人妻人人看人人澡| 日韩免费av在线播放| 亚洲av电影在线进入| 一进一出抽搐动态| 国产亚洲精品综合一区在线观看 | 给我免费播放毛片高清在线观看| 9191精品国产免费久久| 久久婷婷人人爽人人干人人爱| 给我免费播放毛片高清在线观看| 亚洲中文日韩欧美视频| 欧美日本亚洲视频在线播放| 亚洲精品久久国产高清桃花| 99国产精品99久久久久| 97人妻精品一区二区三区麻豆| a在线观看视频网站| 淫妇啪啪啪对白视频| 人人妻,人人澡人人爽秒播| 人成视频在线观看免费观看| 亚洲人成网站高清观看| 国产精品影院久久| 性色av乱码一区二区三区2| 欧美大码av| 一进一出抽搐gif免费好疼| 久久精品综合一区二区三区| 国产精品亚洲av一区麻豆| 欧美成人午夜精品| 成在线人永久免费视频| 久久精品国产99精品国产亚洲性色| 香蕉久久夜色| 午夜福利高清视频| 叶爱在线成人免费视频播放| www.精华液| 神马国产精品三级电影在线观看 | av中文乱码字幕在线| 在线观看免费日韩欧美大片| 一边摸一边做爽爽视频免费| 人成视频在线观看免费观看| 亚洲国产精品合色在线| 亚洲无线在线观看| 国产99久久九九免费精品| 国产精品av视频在线免费观看| 欧美色欧美亚洲另类二区| 妹子高潮喷水视频| 毛片女人毛片| 欧美三级亚洲精品| 日韩大码丰满熟妇| 在线观看免费视频日本深夜| 99国产精品一区二区蜜桃av| 99国产精品一区二区三区| 国产精品九九99| 中文字幕最新亚洲高清| 久久婷婷人人爽人人干人人爱| 久久精品国产99精品国产亚洲性色| 欧美+亚洲+日韩+国产| 一本一本综合久久| 国产一区二区三区视频了| 麻豆av在线久日| 欧美激情久久久久久爽电影| 性色av乱码一区二区三区2| 午夜日韩欧美国产| 亚洲无线在线观看| 看黄色毛片网站| 天堂√8在线中文| 级片在线观看| 国产91精品成人一区二区三区| 精品久久久久久成人av| 一级a爱片免费观看的视频| 99久久国产精品久久久| ponron亚洲| 亚洲黑人精品在线| 中文在线观看免费www的网站 | 免费在线观看视频国产中文字幕亚洲| 国产精品综合久久久久久久免费| 欧美黄色片欧美黄色片| 丝袜人妻中文字幕| 50天的宝宝边吃奶边哭怎么回事| 三级男女做爰猛烈吃奶摸视频| 久久中文看片网| 国产成人欧美在线观看| 国产在线观看jvid| 亚洲成a人片在线一区二区| 一二三四在线观看免费中文在| 日本精品一区二区三区蜜桃| 国产精品99久久99久久久不卡| 国产99白浆流出| 亚洲人成77777在线视频| 免费看日本二区| 女同久久另类99精品国产91| 波多野结衣高清作品| 悠悠久久av| 一个人免费在线观看的高清视频| 香蕉国产在线看| 亚洲精品av麻豆狂野| 婷婷六月久久综合丁香| 夜夜夜夜夜久久久久| 国产一级毛片七仙女欲春2| 国产高清有码在线观看视频 | 九色国产91popny在线| 日韩欧美 国产精品| 一个人观看的视频www高清免费观看 | 日韩国内少妇激情av| 国产精品一及| 亚洲免费av在线视频| 亚洲av成人一区二区三| 国产真人三级小视频在线观看| bbb黄色大片| 国产精品亚洲一级av第二区| 亚洲av成人av| 欧美中文日本在线观看视频| 精品福利观看| 久久久水蜜桃国产精品网| 成人三级做爰电影| 在线观看www视频免费| 久久久国产精品麻豆| 丰满人妻熟妇乱又伦精品不卡| 国产三级中文精品| 久久天躁狠狠躁夜夜2o2o| 国产亚洲精品综合一区在线观看 | 久久伊人香网站| 午夜视频精品福利| 最近最新中文字幕大全免费视频| 99精品在免费线老司机午夜| 亚洲精品一区av在线观看| 国产精品久久视频播放| 中文字幕最新亚洲高清| 国产亚洲av高清不卡| 国产精品九九99| 精品第一国产精品| 免费av毛片视频| 久久九九热精品免费| 久久 成人 亚洲| 国产精品一及| 国产成人aa在线观看| 日韩国内少妇激情av| 欧美黄色片欧美黄色片| 久久精品国产99精品国产亚洲性色| 啦啦啦观看免费观看视频高清| www.自偷自拍.com| 18禁裸乳无遮挡免费网站照片| 国产亚洲精品一区二区www| 国产91精品成人一区二区三区| 亚洲一区高清亚洲精品| 妹子高潮喷水视频| 免费人成视频x8x8入口观看| 久久久久久久久中文| 午夜a级毛片| 男插女下体视频免费在线播放| 免费在线观看视频国产中文字幕亚洲| 久久精品影院6| 亚洲av电影不卡..在线观看| 18禁观看日本| 成人手机av| 婷婷亚洲欧美| 免费人成视频x8x8入口观看| 中文亚洲av片在线观看爽| 毛片女人毛片| 久久精品人妻少妇| 国产区一区二久久| 日本 av在线| 国产人伦9x9x在线观看| 男女床上黄色一级片免费看| 国产激情欧美一区二区| 国产一区二区三区在线臀色熟女| 亚洲专区字幕在线| 亚洲五月天丁香| 亚洲精品一卡2卡三卡4卡5卡| a在线观看视频网站| 亚洲中文字幕一区二区三区有码在线看 | 一本一本综合久久| 午夜视频精品福利| 久久久久久亚洲精品国产蜜桃av| 一区福利在线观看| 99热这里只有是精品50| 亚洲国产欧美人成| 亚洲自偷自拍图片 自拍| 久久久久久久精品吃奶| 国产亚洲av高清不卡| 在线观看免费日韩欧美大片| 欧美+亚洲+日韩+国产| 最新在线观看一区二区三区| 一区福利在线观看| 夜夜躁狠狠躁天天躁| 久久精品综合一区二区三区| 黑人操中国人逼视频| 亚洲七黄色美女视频| 国产精品1区2区在线观看.| 男插女下体视频免费在线播放| 99久久久亚洲精品蜜臀av| 国内精品久久久久久久电影| 亚洲成人精品中文字幕电影| 成人18禁在线播放| 日韩三级视频一区二区三区| 欧美日本视频| 母亲3免费完整高清在线观看| svipshipincom国产片| 18禁观看日本| 狂野欧美激情性xxxx| 国产又色又爽无遮挡免费看| 男女那种视频在线观看| 欧美性猛交黑人性爽| 老司机深夜福利视频在线观看| 两个人视频免费观看高清| 又紧又爽又黄一区二区| 可以在线观看的亚洲视频| 国产亚洲精品第一综合不卡| 99热这里只有精品一区 | 欧美性猛交黑人性爽| 国产精品亚洲美女久久久| 国产成人精品久久二区二区91| 国产精品1区2区在线观看.| 欧美乱妇无乱码| ponron亚洲| 两人在一起打扑克的视频| 欧美在线黄色| 成人18禁高潮啪啪吃奶动态图| 国产一区二区激情短视频| 一本大道久久a久久精品| 亚洲国产精品成人综合色| 欧美三级亚洲精品| 日本撒尿小便嘘嘘汇集6| 男人舔女人下体高潮全视频| 50天的宝宝边吃奶边哭怎么回事| 99国产综合亚洲精品| 亚洲色图av天堂| 久久午夜亚洲精品久久| 伊人久久大香线蕉亚洲五| 91麻豆av在线| 国产91精品成人一区二区三区| 91老司机精品| 国产私拍福利视频在线观看| 狂野欧美白嫩少妇大欣赏| 国产精品亚洲av一区麻豆| 18禁观看日本| 欧美日韩福利视频一区二区| 一区二区三区激情视频| 亚洲av熟女| 少妇熟女aⅴ在线视频| 国产黄色小视频在线观看| 真人做人爱边吃奶动态| 国产精品免费一区二区三区在线| 免费在线观看成人毛片| 精品一区二区三区视频在线观看免费| 欧美成人性av电影在线观看| 中文字幕高清在线视频| 国产精品一区二区三区四区久久| 国产精品 欧美亚洲| 中文字幕人成人乱码亚洲影| www国产在线视频色| 精品久久久久久,| 欧美丝袜亚洲另类 | 精品久久久久久成人av| 亚洲自拍偷在线| 久久久国产成人精品二区| 99国产极品粉嫩在线观看| 国产成人一区二区三区免费视频网站| 国内少妇人妻偷人精品xxx网站 | 非洲黑人性xxxx精品又粗又长| 少妇粗大呻吟视频| 麻豆成人午夜福利视频| 精品人妻1区二区| 蜜桃久久精品国产亚洲av| 日韩三级视频一区二区三区| 国产午夜精品论理片| 丝袜人妻中文字幕| 亚洲av成人不卡在线观看播放网| 99热这里只有精品一区 | 精品免费久久久久久久清纯| 全区人妻精品视频| 桃色一区二区三区在线观看| 免费av毛片视频| 99精品在免费线老司机午夜| 18禁美女被吸乳视频| 精品一区二区三区视频在线观看免费| xxxwww97欧美| 久久中文看片网| 亚洲av片天天在线观看| 在线观看午夜福利视频| 女人高潮潮喷娇喘18禁视频| 久久久久精品国产欧美久久久| 淫秽高清视频在线观看| 国产精品乱码一区二三区的特点| 国产欧美日韩一区二区精品| 国产三级在线视频| 精品第一国产精品| 欧美性猛交黑人性爽| av免费在线观看网站| 欧美色视频一区免费| 啦啦啦免费观看视频1| 最近最新中文字幕大全电影3| 久久中文字幕人妻熟女| 在线a可以看的网站| 黄色片一级片一级黄色片| 国产真人三级小视频在线观看| 99热这里只有是精品50| 亚洲精品中文字幕一二三四区| 精品国产亚洲在线| 久久久久国产一级毛片高清牌| 亚洲av美国av| 国产精品乱码一区二三区的特点| 一本一本综合久久| 国产精品久久久av美女十八| 观看免费一级毛片| 一夜夜www| 亚洲中文字幕一区二区三区有码在线看 | 可以免费在线观看a视频的电影网站| 国产主播在线观看一区二区| 窝窝影院91人妻| 老鸭窝网址在线观看| 999久久久国产精品视频| 国产久久久一区二区三区| 精品久久久久久久毛片微露脸| 老熟妇乱子伦视频在线观看| 非洲黑人性xxxx精品又粗又长| 一区福利在线观看| 国产亚洲精品综合一区在线观看 | 一区二区三区激情视频| 操出白浆在线播放| 在线永久观看黄色视频| 国产午夜精品论理片| 最近最新免费中文字幕在线| av中文乱码字幕在线| 一本精品99久久精品77| 国产伦人伦偷精品视频| 日本黄大片高清| 熟女少妇亚洲综合色aaa.| 亚洲激情在线av| 中文字幕最新亚洲高清| 99热只有精品国产| 午夜精品一区二区三区免费看| 国产一区二区激情短视频| 特级一级黄色大片| 在线观看日韩欧美| av在线播放免费不卡| 国产精品野战在线观看| 亚洲精华国产精华精| 欧美日本亚洲视频在线播放| 亚洲第一电影网av| 91av网站免费观看| 人妻夜夜爽99麻豆av| 亚洲国产精品久久男人天堂| 99国产综合亚洲精品| 欧美成人午夜精品| 久久久久国产一级毛片高清牌| 99精品欧美一区二区三区四区| 国产精品一区二区三区四区免费观看 | 日韩欧美三级三区| 欧美日韩国产亚洲二区| tocl精华| av欧美777| 欧美乱码精品一区二区三区| 午夜福利视频1000在线观看| 午夜福利欧美成人| 欧美高清成人免费视频www| 黄片大片在线免费观看| 国产不卡一卡二| 亚洲成av人片在线播放无| 桃红色精品国产亚洲av| 国产不卡一卡二| 久久久久久久久中文| 成年人黄色毛片网站| 日韩 欧美 亚洲 中文字幕| 一级毛片高清免费大全| 日本一二三区视频观看| 美女免费视频网站| 色综合婷婷激情| 精品欧美国产一区二区三| 国内揄拍国产精品人妻在线| 好看av亚洲va欧美ⅴa在| 国产真实乱freesex| 在线永久观看黄色视频| 又黄又粗又硬又大视频| 国产麻豆成人av免费视频|