• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Evolution of limestone fracture permeability under coupled thermal, hydrological, mechanical, and chemical conditions*

    2014-06-01 12:30:00LIFengbin李鳳濱SHENGJinchang盛金昌ZHANMeili詹美禮XULimeng徐力猛WUQiang吳強JIAChunlan賈春蘭
    關鍵詞:吳強金昌春蘭

    LI Feng-bin (李鳳濱), SHENG Jin-chang (盛金昌), ZHAN Mei-li (詹美禮), XU Li-meng (徐力猛), WU Qiang (吳強), JIA Chun-lan (賈春蘭)

    College of Conservancy and Hydropower Engineering, Hohai University, Nanjing 210098, China, E-mail: lanxue151@163.com

    Evolution of limestone fracture permeability under coupled thermal, hydrological, mechanical, and chemical conditions*

    LI Feng-bin (李鳳濱), SHENG Jin-chang (盛金昌), ZHAN Mei-li (詹美禮), XU Li-meng (徐力猛), WU Qiang (吳強), JIA Chun-lan (賈春蘭)

    College of Conservancy and Hydropower Engineering, Hohai University, Nanjing 210098, China, E-mail: lanxue151@163.com

    (Received March 12, 2013, Revised July 3, 2013)

    The effect of temperature on the rock fracture permeability is a very important factor in the prediction of the permeability of enhanced geothermal systems and in reservoir engineering. In this study, the flow-through experiments were conducted on a single limestone fracture at different temperatures of 25oC, 40oC and 60oC, and with differential pressures of 0.3 MPa and 0.4 MPa. The experimental results suggest a complex temporal evolution of the fracture aperture. The aperture increases considerably with increasing temperature and reduces gradually to a steady value at a stable temperature. The results of three short-term experiments (QT-1, QT-2, QT-3) indicate an exponential relationship between the permeability and the temperature change ratio (ΔT/ T), which provides a further evidence that the rising temperature increases the aperture. It is shown that the changing temperature has its influence on two possible accounts: the chemical dissolution and the pressure dissolution. These two processes have opposite impacts on the fracture permeability. The chemical dissolution increases the permeability with a rising temperature while the pressure dissolution reduces the permeability with a stable temperature. These make a very complex picture of the permeability evolution. Our results show that the fracture permeability reduces 39.2% when the temperature increases by 15oC (during the 25oC-40 C interval) and 42.6% when the temperature increases by 20oC (during the 40oC-60oC interval). It can be concluded that the permeability decreases to a greater extent for larger increases in temperature.

    permeability, temperature, fracture aperture, rock fracture

    Introduction

    In underground engineering, particularly, in the petroleum reservoirs, the geological sequestration of CO2, and the reservoirs used for the sequestration of energy by-products such as radioactive waste, the permeability evolution law in fractured rocks coupled by thermal-hydrologic-mechanical-chemical processes is very important. The temperature, in particular, has considerable effects on the flow and transport behavior in fractured rocks coupled by thermal-hydrologicmechanical-chemical processes[1,2]. At moderate temperatures and wet environment, resulting of chemical reaction and stress, the subcritical crack growth takes place in the rocks[3], and the removal of the mineral mass as a result of the occurrence of bridging asperities within the fracture[4], leading to a decrease of the fracture aperture. At high temperatures, the rock fracture heals and seals microcracks and reduces the permeability, and especially at long time of elevated stress and temperature[5], caused by violent chemical reactions impacted on the process of the dissolution and the precipitation on the fracture surface[6]. The flowthrough tests were conducted at moderate temperatures of 20oC, 80oC, 90oC, 120oC and 150oC[4,7]to study the evolution of the fracture permeability, but not at 40oC and 60oC.

    Both at moderate temperatures, and at high temperatures[6], the fracture permeability in the quartz-domain rock, all decreases with increasing time, and monotonically at stepped-temperatures[7]. However, for different components, the effects of temperature, stre-ss, and chemical have different responses in the limestone, leading to more complicated flow and transport behaviors in the fracture. The dissolution on the fractured surface in the limestone is sensitive to aqueous conditions[8,9]. The changing temperature has a great effect on the chemical reaction, the fracture aperture is controlled by the competition of stress and reactivity, leading to greater complexity.

    In the present study, a flow-through experiment was conducted on a single rock fracture in the limestone at temperatures of 25oC, 40oC and 60oC under differential pressures of 0.3 MPa and 0.4 MPa. The fracture aperture was evaluated from the measured flow rate. The results of the experiments are complicated, thus, two different methods are employed to analyze the experimental results. First, three other temperature-dependent experiments were conducted to allow a detailed study of the effects of rising temperature on the permeability characteristics. Then, a more detailed analysis of the influence of temperature on the fluid flow is made to help elucidate the influence of the temperature on the fracture permeability at higher and more stable temperatures.

    Fig.1 Experimental equipment and rock sample

    1. Experimental method

    In order to study the behavior of the rock fracture permeability characteristics during heating and at constant moderate temperatures (25°C-60°C), a water flow-through experiment was conducted based on a multifield coupling system for rock fractures. The tap water was used as the permeant fluid to replicate the characteristics of the natural fluid in deep rock fractures under complex environmental conditions. The rock used is a cylindrical sample of limestone (0.05 m diameter, 0.1 m length) containing a single diametral fracture along the cylindrical axis (Fig.1). This sample was collected from a mountain in Jiaxiang Country, Jining City, Shandong Province, China. The fracture was induced using the Brazilian test by tensile stress within the sample. The same fractured rock sample was used throughout the test, and the measured flow rates yield a continuous record of the average fracture transmissivity, which can be converted to obtain the average hydraulic aperture. The ion concentration in the effluent flow is also examined after the experiment, but will not be discussed in this paper.

    1.1 Experimental system

    The fluid flow system is illustrated in Fig.1. The rock sample is saturated according to the operational standard. After gently washing the fracture surfaces with distilled water, the two half-rock samples are fitted together carefully to avoid introducing small debris into the fracture. Then, the fitted core is coated with a thin silicone gel layer of 704. The fitted core is again wrapped with a double heat-shrink tube. Such a careful treatment is applied to avoid the flow of the fluid through the existing void in the outside wall of the rock, and to prevent the confining-pressure leakage occurring as a result of punching or rupturing of the sleeve under high temperature and pressure conditions. After the silicone consolidation, the core is placed inside a pressure cell to be adequately jacketed. The confining pressure, the axial compression, and the osmotic pressure are controlled by computer, with dynamic accuracies within ±0.15 MPa, ±7.5 kN and ±0.002 MPa , respectively. A casting body composed of the founded aluminum stainless steel heating pipe is used to heat the cell and complete the heating process, from room temperature to 150oC, within 3 h. The flow rates are evaluated by weighing the effluent water flowing out of the pressure cell directly, the rates are recorded every minute throughout the flowthrough experiments.

    1.2 Experimental procedure

    The flow-through experiment was conducted in four stages (1-4), under the confining pressure of 2.5 MPa, the axial compression of 15 MPa, the differential water pressure of 0.3 MPa or 0.4 MPa, and the temperatures of 25°C, 40°C and 60°C (Table 1). Two of the experimental stages (1 and 2) were conducted under the confining pressure of 2.5 MPa and at 25°Cin order to compare the hydraulic aperture under different differential water pressures.

    Table 1 Experimental conditions

    After being jacketed, the rock sample was constrained within the pressure cell and pressurized to 3 MPa (or more) by axial compression to ensure an adequate connection between the porous plate and the force transmission column, and to prevent the water pathway from becoming immersed by the confining pressure oil. Then, the antiwear hydraulic oil was injected into the cell, the confining fluid was pressurized to a specified confining pressure, and the axial compression was modulated accordingly. The flow-through experiment was initiated at a controlled water pressure differential and at room temperature; the flow rate intervals were measured and the water samples were kept for the ion concentration measurement. In each experiment, a stable flow rate was reached and maintained for at least one day before the subsequent experiment.

    Experiments last nearly one month, to measure the effluent flow rate at the outlet of the fracture rock. The fluid flow could be considered as the laminar flow for the small flux in the rock fracture. The cubic law for seepage through rock fractures, proposed by Boussinesq (1868) for the description of the movement of liquid in the gap between parallel plates, is suitable for describing the laminar flow movement. The measured flow rate, q, is formulated as follows:

    where A is the cross-sectional area of the rock fracture, V is the flow velocity across the rock fracture, K is the hydraulic conductivity, J is the hydraulic gradient, D is the diameter of the rock, b is the hydraulic aperture, g is the gravity acceleration, L is the length of the rock sample, Δp is the differential water pressure, k is the fracture permeability, and ν and ρ are the kinetic viscosity and the density of the fluid, respectively (Table 2).

    Table 2 Parameters in Eqs.(1)-(3)

    Fig.2 Evolution of flow rate measured at different experimental stages

    2. Experimental results

    The results of the flow-through experiment are presented in Figs.2 and 3 where Δp is differentialpressure, T is temperature. Stage-1 starts 10 h after the loading of the differential pressure. The flow rate is stabilized during this stage and the differential pressure is increased to 0.4 MPa in about 50 h after the start of the stage, thereafter, stage-2 is initiated. In stage-2, the experiment is stabilized, the temperature is increased to 40oC and then stage-3 is initiated. Some short auxiliary experiments are conducted at the end of stage-3, resulting in a discontinuity in the experimental timeline prior to the start of stage-4. The rock cell is heated from room temperature at the beginning of stage-4. Due to some improper operation, a temperature higher than 60oC appears at initial several hours. The rock cell is cooled, and then heated to 60oC. Accordingly, the peaks of the flow rate and the fracture aperture appear at the beginning of stage-4 (Figs.2 and 3).

    Fig.3 Evolution of fracture aperture measured at 25oC (stage-1, stage-2), 40°C (stage-3), and 60oC (stage-4), and differential pressure of 0.3 MPa (stage-1) and 0.4 MPa (stage-2, stage-3, stage-4). The fracture aperture is evaluated from the recorded flow rates and the cubic law and is displayed against experimental time

    The fracture aperture exhibits a complex behavior during the four experimental stages. It decreases rapidly with time in stage-1 and then approaches a stable value, as in good agreement with the results of Yasuhara et al.[10]. The fracture aperture is decreased by 80.2% during this stage. After the differential pressure is increased to 0.4 MPa, the fracture aperture measured in stage-2 is increased considerably before it is once again decreased and approaches a more stable value. This indicates that the permeability is switched gradually from an increasing trend to a decreasing trend in response to the change in the differential pressure. During this process, the fracture aperture is increased by 17.9% in conjunction with a differential pressure increase of 33.3%. The peaks of the fracture aperture occur in response to the heating in stage-3 and stage-4, suggesting that the fracture aperture is enhanced by these increases of temperature. The promoted transmission may be helped by the process of mineral dissolution[11]. In the experiment, a constant temperature is maintained after these peaks of the fracture aperture. The fracture aperture is decreased to 1.37 μm after 140.95 h in stage-3 and to 0.94 μm after 91.6 h in stage-4. The decrease of the fracture aperture with time may be resulted from the irreversible inelastic crushing (i.e., mechanical failure) of the propping asperities, the dissolution at the contacting asperities, and the clogging of the fracture void by mineral precipitation[12]. The fracture aperture is decreased by 39.6% in stage-3 accompanied with an increase of 15oC of the temperature and by 63.7% in stage-4 accompanied with an increase of 20oC of the temperature, that is, the fracture aperture is decreased to a greater extent for a larger increase of the temperature.

    In the experiments conducted by Polak[7], the measurement of fluid and dissolved mass fluxes, the concurrent X-ray CT and imaging, and the post-test sectioning and SEM were used to constrain the progress of the mineral dissolution and its effect on the transport properties. The results of previous studies indicate a general correspondence between the mineral mass removed from the contacting asperities of a conductive fracture, the measured change in the hydraulic aperture, and the nondestructive observed removal of mass from the fracture contact area. The evolution of the fracture aperture (i.e., the hydraulic aperture) is used to describe the mean removal of mass from the fracture contact area in this study.

    The results in Fig.3 indicate that the temperature has a considerable effect on the fracture aperture, in particular, the aperture changes dramatically in response to the temperature increases at the beginning of stage-4. To some extent, the evolution of the fracture aperture can be considered to express the fracture permeability characteristics of the rock (e.g., Eq.(3)).

    3. Rising temperature and rock fracture permeability

    To study the effects of the temperature on the fracture permeability, three short-term temperature-dependent experiments (QT-1, QT-2, QT-3) were conducted under the axial compression of 15 MPa, the confining pressure of 2.5 MPa, and the differential pressure of 0.4 MPa (Fig.4). The results of these experiments suggest that the flow rate increases with the increase of the temperature. The temperature and the flow values were collected simultaneously in the experiments, the temperature was measured in the confining pressure oil by a temperature sensor and is not entirely representative of the current temperature in the fracture. However, the computer simulation indicates that, from the temperature in the confining pressure oil, the surface temperature of the rock fracture delays only seven minutes to reach that value. This lag time is considered negligible when compared with the overall experiment time.

    Fig.4 Comparison of the flow rate and temperature for QT-1, QT-2, and QT-3 under axial compression of 15 MPa, confining pressure of 2.5 MPa, and differential pressure of 0.4 MPa

    Table 3 shows the experimental results of the rising temperature sections of the experiments QT-1, QT-2, QT-3, leaving out the cooling sections. Each test case results are shown in the same row in Table 3. Temperature increment, ΔT, is the difference between the current temperature and the previous-row temperature (listed at the previous column of the same row). The data for 39.2oC is omitted

    Theoretical and experimental data are combined to illustrate the phenomena apparent in the experiments. Yasuhara[12]produced an equation describing the fracturing rate for a tensile opening mode

    where A is a pre-exponential factor, R is universal gas constant, f( KI) is a stress intensity factor, which becomes a constant under the stable confining pressure. In view of the relationship between the flow rate and the fracture aperture (i.e., Eqs.(1)-(3)), the relationship between the flow variation rate, dq/dT, and the temperature might be similar to that between the fracturing rate and the temperature, as

    where A is a pre-exponential factor related to the stress intensity factor. Table 3 illustrates the reduction of the change rate of the flow rate with increasing temperature and the change behaviors relating to the initial temperature. Accordingly, Eq.(5) is modified as follows

    The experimental data from QT-1, QT-2 and QT-3 are used to fit curves for the parameters A and B (Table 4).

    The relationship between the flow rate and the permeability is provided by Eq.(1). When the differential pressure and the cross-sectional area of the fracture are constant, the changes of the permeability resulting from increasing temperature can be described as follows

    where KTis a coefficient of the permeability related to the increasing temperature. However, it should be noted that this section discusses only the condition where all variables except the temperature are kept constant.

    Table 3 The relationship between temperature and flow rate in QT-1, QT-2 and QT-3

    Table 4 Fitting of Eq.(6) based on experimental data from QT-1, QT-2 and QT-3

    The parameters A and B are found to be greater than zero (Table 4), indicating that increasing temperature causes an increase in the coefficient of the permeability of the rock fracture, which corresponds to peaks of the flow rate and the fracture aperture during stage-3-1 and stage-4 in macroscopic observations (i.e., during the first 10 h and for 26 h-37 h, respectively). Parameter B is related to the activation enthalpy (e.g., Eq.(4)). Parameter A may be mediated by the material characteristics, the stress intensity factor, and various temperature-dependent factors, accordingly. The value of A determined from QT-3 is four orders of magnitude smaller than those derived from the other two experiments. Only two groups of experimental data from QT-1 produce less accurate results for the fitting curve, and these results are used for reference. Moreover, the flow rate through the fracture is affected in a complex way by the cooling and the effective stress during temperature decreasing (i.e., the decreasing trends illustrated in Figs.4(a) and 4(b), to show the appearance of a slow declining.

    4. Effects of temperature on the physical and chemical properties of rock fracture

    The changes of the temperature influence the fracture apertures through changes of material properties, chemical reaction rates, and flow-through characteristics, all of which are temperature-dependent processes that affect the rate of mineral dissolution.

    In particular, the critical stress of the propping particles in the fracture apertures is decreased with increasing temperature. The stress-mediated process of subcritical cracking was investigated in detail[5,13-15], and their findings were applied to describe the compaction behavior in granular aggregates[16,17]. The pressure solutions may result in a time-dependent decrease of the fracture permeability through compaction driven by the fracturing (or crushing) of the propping asperities and by the dissolution at contacting asperities. The critical stress, cσ, can be determined through the energy balance under the applied stress and temperature conditions[18], which defines the stress state where the compaction of the grain aggregate will effectively halt[12]. The variation of the critical stress on the propping particles in the fracture, Δcσ, is defined as

    According to Eq.(8),cσ decreases with increasing temperature. Before heating, the fracture closure rate is decreased, indicating a balance between σcand the asperity-contact stress,aσ, on the contact area.Conversely, after heating,aσ is greater thancσ, which drives the process of the pressure dissolution. Thus, a high stable temperature is dominated by the effects of the pressure solution mechanisms, and the fracture permeability is decreased during this process.

    It is well known that the increase of temperature can promote the chemical dissolution, on the propping particle and the free surface in the rock fracture. The transition state theory (TST) holds that the chemical reaction processes are initiated only by the collision of reactant molecules with sufficient energy (i.e., activation energy), and with appropriate collision angles. The number of molecules with activation energy is increased with increasing temperature. Moreover, according to the Arrhenius equation, the reaction rate constant is higher for a higher temperature. In such cases, the chemical dissolution of the contacting particle and the free surface are accelerated.

    The fluid viscosity is known to decrease with increasing temperature. The relationship between the dynamic viscosity of water, μ, and the temperature, t, can be expressed as follows

    where μ is calculated. ν=μρ-1, where ν is the kinetic viscosity of water. Thus, ν decreases with increasing temperature. According to Eqs.(1) and (3), the fracture permeability and the flow rate are increased with all other conditions kept unchanged.

    5. Effects of temperature changes on permeability

    Increasing temperature will increase the rate of the mineral dissolution on the free surface, and enhance the fracture permeability. The transmission in dominant fractures can be enhanced by processes such as the shear dilation, the mineral dissolution[9,11], and the strain energy driven free-face dissolution. In particular, the mineral dissolution, driven by the chemical reactions in the fracture void during compaction, is accelerated as a result of increasing temperature, this changes the morphology of the fracture surfaces and increases the hydraulic aperture. Moreover, the changes in the fracture surface result in permeability changes, such that the fracture permeability increases over time during the periods of increasing temperature in stage-3-1 and stage-4-1. Furthermore, the increasing temperature promotes the expansion of the rock fracture, opening the fracture. Under such combined action, the increasing temperature increases the fracture permeability.

    During a higher stable temperature, the fracture permeability decreases. In the stable temperature intervals in stage-3-2 and stage-4-2, the decreasing critical stress drives the pressure solution. The propping particles in the fracture are dissolved in the pressure solution process and the fracture closes slowly at compaction. However, the dissolution rate slows over time with the increase of the contact area, and the closure of the fracture decreases the permeability.

    Throughout the intervals of increasing and stable temperature, the fracture permeability decreases significantly at the end of each experimental stage. The permeability increases by 13.3% in stage-3-1, decreases by 34.7% in stage-3-2, and decreases by 39.2% in stage-3 in the lump. Conversely, the permeability increases by 59.5% in stage-4-1, decreases by 73.24% in stage-4-2, and decreases by 42.6% in stage-4 in the lump. The permeability characteristics are important in the prediction of the permeability of the earthquake-disturbed belt, the radioactive waste repositories, and the basic facilities for underground reservoir engineering, when the temperature changes.

    Table 5 Percentage changes in the permeability at different temperatures

    The values with a percent sign in Table 5 show the changing of the permeability. “+”sign means increasing, and “-” means decreasing. The change is the compared value at the end time with the value at the beginning time at the same phase. So the general trends in stage-3 and stage-4 are decreasing in the permeability.

    6. Conclusions

    Flow-through experiments were conducted to measure the evolution of the aperture in a fracture rock at different temperatures.

    (1) The experimental results indicate that the evolution of the fracture aperture with time is complex: the aperture increases significantly during the intervals of rising temperature, but reduces gradually to a steady state under stable temperature conditions.

    (2) Rising temperature can improve the rock fracture permeability. The fitting data for these three short-term experiments (QT-1, QT-2 and QT-3) confirm an exponential relationship between the permeability and the temperature change ratio, ΔT/T, which helps explain the increases of the fracture aperture during stage-3-1 and stage-4-1.

    (3)Temperature affects the transport behavior in the rock fracture in three respects. First, the increased temperature diminishes the critical stress-driven pressure solution, reducing the permeability of the fra-cture by compaction. Second, the increased temperature promotes the chemical dissolution, leading to an accelerated dissolution of the propping particles and the free surface in the fracture. Third, the increased temperature reduces the fluid viscosity, enhancing the flow rate.

    (4) The increasing temperature accelerates the chemical dissolution and opens the fracture, leading to an increased permeability; at higher stable temperatures, the enhanced pressure dissolution mechanisms reduce the fracture permeability.

    (5) Under a combined action, the permeability decreases by 39.2% for a temperature increase of 15oC (i.e., during the experimental stage of 25oC-40oC) and by 42.6% for a temperature increase of 20oC (i.e., during the experimental stage of 40oC-60oC). This result indicates that reductions of the permeability are greater for larger temperature increases.

    [1] YASUHARA H., ELSWORTH D. and POLAK A. Evolution of permeability in a natural fracture: Significant role of pressure solution[J].Journal of Geophysical Research:Solid Earth,2004,109(B3): B03204.

    [2] YASUHARA H., ELSWORTH D. and POLAK A. et al. Spontaneous switching between permeability enhancement and degradation in fractures in carbonate: Lumped parameter representation of mechanicallyand chemically-mediated dissolution[J].Transport inPorous Media,2006, 65(3): 385-409.

    [3] NARA Y., KANEKO K. Study of subcritical crack growth in andesite using the double torsion test[J].International Journal of Rock Mechanics andMining Sciences,2005, 42(4): 521-530.

    [4] YASUHARA H., KINOSHITA N. and OHFUJI H. et al. Temporal alteration of fracture permeability in granite under hydrothermal conditions and its interpretation by coupled chemo-mechanical model[J].AppliedGeochemistry,2011, 26(12): 2074-2088.

    [5] RUTQVIST J., FREIFELD B. and MIN K. B. et al. Analysis of thermally induced changes in fractured rock permeability during 8 years of heating and cooling at the Yucca Mountain Drift Scale Test[J].International Journal of Rock Mechanics and MiningSciences,2008, 45(8): 1373-1389.

    [6] MORROW C. A., MOORE D. E. and LOCKNER D. A. Permeability reduction in granite under hydrothermal conditions[J].Journal of Geophysical Research: Solid Earth,2001, 106(B12): 30551-30560.

    [7] POLAK A., YASUHARA H. and ELSWORTH D. et al. The evolution of permeability in natural fracturesthe competing roles of pressure solution and free-face dissolution[J].Elsevier Geo-Engineering Book Se-ries,2004, 2: 721-726.

    [8] POLAK A., ELSWORTH D. and LIU J. et al. Spontaneous switching of permeability changes in a limestone fracture with net dissolution[J].Water Resou-rces Research,2004, 40(3): W03502.

    [9] LIU J., SHENG J. and POLAK A. et al. A fully-coupled hydrological-mechanical-chemical model for fracture sealing and preferential opening[J].International Journal of Rock Mechanics and Mining Scie-nces,2006, 43(1): 23-36.

    [10] YASUHARA H., POLAK A. and MITANI Y. et al. Evolution of fracture permeability through fluid-rock reaction under hydrothermal conditions[J].Earth Pla-net Science Letters,2006, 244(1-2): 186-200.

    [11] TARON J., ELSWORTH D. Thermal-hydrologic-mechanical-chemical processes in the evolution of engineered geothermal reservoirs[J].International Journal of Rock Mechanics and Mining Sciences,2009, 46(5): 855-864.

    [12] YASUHARA H., ELSWORTH D. Compaction of a rock fracture moderated by competing roles of stress corrosion and pressure solution[J].Pure AppliedGeophysics,2008, 165(7): 1289-1306.

    [13] DOVE P. M. Geochemical controls on the kinetics of quartz fracture at subcritical tensile stresses[J].Journal of Geophysical Research:Solid Earth,1995, 100(B11): 22349-22359.

    [14] FENG X., CHEN S. and LI S. Effects of water chemistry on microcracking and compressive strength of granite[J].International Journal of Rock Mechanicsand Mining Sciences,2001, 38(4): 557-568.

    [15] WILTSCHKO D. V., MORSE J. W. Crystallization pressure versus ‘‘crack seal’’ as the mechanism for banded veins[J].Geology,2001, 29(1): 79-82.

    [16] KARNER S. L., CHESTER F. M. and KRONENBERG A. K. et al. Subcritical compaction and yielding of granular quartz sand[J].Tectonophysics,2003, 377(3-4): 357-381.

    [17] CHESTER J. S., LENZ S. C. and CHESTER F. M. et al. Mechanisms of compaction of quartz sand at diagenetic conditions[J].Earth Planet Science Letters,2004, 220(3-4): 435-451.

    [18] REVIL A. Pervasive pressure-solution transfer: A poro-visco-plastic model[J].Geophysical Research Letters,1999, 26(2): 255-258.

    10.1016/S1001-6058(14)60026-3

    * Project supported by the National Natural Science Foundation of China (Grant Nos. 50779012, 51009053 and 51079039).

    Biography: LI Feng-bin (1986-), Female, Ph. D. Candidate

    SHENG Jin-chang, E-mail: jinchang@hhu.edu.cn

    猜你喜歡
    吳強金昌春蘭
    我的媽媽
    張金昌簡介
    精細化健康體檢管理模式在體檢中心的應用探析
    金昌浩、王正油畫作品選
    金昌浩油畫作品選
    從機構遠離看AGM和EFB
    你有什么了不起
    對推進武鳴縣文化大發展大繁榮的幾點思考
    211282 Comparison of long-term graft patency of onpump versus off-pump coronary artery bypass grafting
    歐元危機與歐洲的未來
    新民周刊(2011年44期)2011-05-30 10:48:04
    国产成人欧美在线观看 | 亚洲av成人一区二区三| 亚洲欧洲精品一区二区精品久久久| 精品少妇久久久久久888优播| 女人爽到高潮嗷嗷叫在线视频| 国产日韩欧美视频二区| 国产一卡二卡三卡精品| 一区二区三区精品91| 免费久久久久久久精品成人欧美视频| 国产成人a∨麻豆精品| 午夜两性在线视频| 欧美黄色片欧美黄色片| 免费观看a级毛片全部| 久久ye,这里只有精品| 欧美激情久久久久久爽电影 | 国产一区二区激情短视频 | 午夜日韩欧美国产| svipshipincom国产片| 岛国在线观看网站| 一区二区日韩欧美中文字幕| 久久99一区二区三区| 亚洲av男天堂| 两性午夜刺激爽爽歪歪视频在线观看 | 岛国毛片在线播放| 日韩有码中文字幕| 男男h啪啪无遮挡| 女人被躁到高潮嗷嗷叫费观| 国产成人精品在线电影| 热99re8久久精品国产| 亚洲 欧美一区二区三区| 久久久精品区二区三区| 18禁国产床啪视频网站| 1024视频免费在线观看| 夫妻午夜视频| 一边摸一边做爽爽视频免费| 一本一本久久a久久精品综合妖精| 99国产精品一区二区蜜桃av | 免费观看a级毛片全部| 两个人看的免费小视频| 亚洲国产成人一精品久久久| 90打野战视频偷拍视频| 日韩大片免费观看网站| 手机成人av网站| 久久国产精品男人的天堂亚洲| 亚洲av电影在线进入| 久久精品久久久久久噜噜老黄| 制服人妻中文乱码| 国产成人欧美| 色94色欧美一区二区| 欧美日韩一级在线毛片| 欧美乱码精品一区二区三区| 精品亚洲成a人片在线观看| 91成年电影在线观看| 日韩有码中文字幕| netflix在线观看网站| 自线自在国产av| 国产三级黄色录像| 日韩大片免费观看网站| 免费日韩欧美在线观看| 两个人免费观看高清视频| 精品福利永久在线观看| 人人澡人人妻人| 又紧又爽又黄一区二区| 黑丝袜美女国产一区| 亚洲欧美一区二区三区黑人| 多毛熟女@视频| 下体分泌物呈黄色| 一本一本久久a久久精品综合妖精| 国产黄色免费在线视频| 久久青草综合色| 国产一级毛片在线| 国产一区二区三区综合在线观看| 国产熟女午夜一区二区三区| 精品卡一卡二卡四卡免费| www.自偷自拍.com| 肉色欧美久久久久久久蜜桃| 夫妻午夜视频| 成人av一区二区三区在线看 | 一区二区三区乱码不卡18| 亚洲av成人不卡在线观看播放网 | 欧美国产精品va在线观看不卡| 亚洲少妇的诱惑av| 狠狠狠狠99中文字幕| 一本—道久久a久久精品蜜桃钙片| 两个人看的免费小视频| 日日摸夜夜添夜夜添小说| 99国产精品99久久久久| av在线播放精品| 亚洲专区字幕在线| 午夜福利影视在线免费观看| 国产亚洲一区二区精品| 国产成人欧美| 国产又爽黄色视频| 日韩欧美一区二区三区在线观看 | 中国国产av一级| 我要看黄色一级片免费的| 亚洲中文字幕日韩| 国产亚洲av片在线观看秒播厂| 欧美午夜高清在线| 久久中文字幕一级| cao死你这个sao货| 日韩制服骚丝袜av| 久久久久久久久免费视频了| 免费日韩欧美在线观看| 国产深夜福利视频在线观看| 亚洲精品粉嫩美女一区| 国产成人欧美在线观看 | av网站在线播放免费| 极品人妻少妇av视频| 不卡一级毛片| av线在线观看网站| 午夜福利视频在线观看免费| 国产一区二区激情短视频 | 久9热在线精品视频| 国产亚洲午夜精品一区二区久久| 18禁裸乳无遮挡动漫免费视频| 大码成人一级视频| 啦啦啦在线免费观看视频4| 中文字幕精品免费在线观看视频| 亚洲精品中文字幕在线视频| 国产主播在线观看一区二区| 51午夜福利影视在线观看| 少妇的丰满在线观看| 国产精品久久久久成人av| 人人妻,人人澡人人爽秒播| 考比视频在线观看| 大型av网站在线播放| 免费在线观看黄色视频的| 淫妇啪啪啪对白视频 | 欧美成人午夜精品| 亚洲欧美色中文字幕在线| 俄罗斯特黄特色一大片| 成人国产av品久久久| 高清在线国产一区| 狂野欧美激情性bbbbbb| 青春草视频在线免费观看| www.999成人在线观看| 色精品久久人妻99蜜桃| 精品久久蜜臀av无| 亚洲av成人一区二区三| 九色亚洲精品在线播放| 国产亚洲精品第一综合不卡| 国产亚洲欧美在线一区二区| 日本wwww免费看| 久久热在线av| 丰满少妇做爰视频| 韩国高清视频一区二区三区| 亚洲av美国av| 国产色视频综合| 18禁裸乳无遮挡动漫免费视频| 搡老乐熟女国产| 一级黄色大片毛片| 青春草视频在线免费观看| 少妇裸体淫交视频免费看高清 | av天堂在线播放| 老司机影院毛片| 一区二区三区精品91| 一区二区av电影网| 黑人操中国人逼视频| 亚洲欧美激情在线| 精品人妻一区二区三区麻豆| 国产91精品成人一区二区三区 | 国产国语露脸激情在线看| 亚洲av日韩在线播放| 久久久久国内视频| 午夜精品久久久久久毛片777| 中文精品一卡2卡3卡4更新| 搡老熟女国产l中国老女人| 女人被躁到高潮嗷嗷叫费观| 欧美变态另类bdsm刘玥| 久久精品成人免费网站| 日韩大片免费观看网站| 亚洲中文日韩欧美视频| 欧美日韩国产mv在线观看视频| 丝袜脚勾引网站| 日韩欧美国产一区二区入口| 90打野战视频偷拍视频| 久久这里只有精品19| 99久久国产精品久久久| 一级毛片女人18水好多| 两性午夜刺激爽爽歪歪视频在线观看 | 亚洲国产日韩一区二区| 超色免费av| 欧美少妇被猛烈插入视频| 国产在视频线精品| 欧美成人午夜精品| 午夜福利视频在线观看免费| 女人久久www免费人成看片| 欧美精品一区二区大全| e午夜精品久久久久久久| 黄色毛片三级朝国网站| 在线观看www视频免费| 成年动漫av网址| 久久久久久久久久久久大奶| 法律面前人人平等表现在哪些方面 | 欧美另类一区| 国产精品一区二区精品视频观看| 亚洲 国产 在线| 啦啦啦 在线观看视频| 国产精品久久久久久人妻精品电影 | 欧美黄色片欧美黄色片| 天天操日日干夜夜撸| 99精品久久久久人妻精品| 正在播放国产对白刺激| 久久人人爽人人片av| 亚洲av成人不卡在线观看播放网 | av片东京热男人的天堂| 成人三级做爰电影| av不卡在线播放| 热99久久久久精品小说推荐| 亚洲精华国产精华精| 国产区一区二久久| 丝袜美足系列| 蜜桃国产av成人99| 亚洲国产精品999| 1024视频免费在线观看| 欧美大码av| 97精品久久久久久久久久精品| 国产精品香港三级国产av潘金莲| 久久女婷五月综合色啪小说| 午夜精品久久久久久毛片777| 91麻豆av在线| 免费一级毛片在线播放高清视频 | 法律面前人人平等表现在哪些方面 | 免费在线观看影片大全网站| 亚洲人成77777在线视频| 视频区图区小说| 精品少妇久久久久久888优播| 欧美日韩精品网址| 一区二区日韩欧美中文字幕| 亚洲性夜色夜夜综合| 少妇人妻久久综合中文| 亚洲精品久久午夜乱码| 免费在线观看影片大全网站| 欧美日本中文国产一区发布| 亚洲一卡2卡3卡4卡5卡精品中文| 熟女少妇亚洲综合色aaa.| 亚洲欧美精品综合一区二区三区| 国产xxxxx性猛交| 免费观看人在逋| 亚洲国产欧美在线一区| av不卡在线播放| 老司机靠b影院| 久久久久精品人妻al黑| 国产麻豆69| 精品国产国语对白av| 国产精品麻豆人妻色哟哟久久| 久久久欧美国产精品| 少妇裸体淫交视频免费看高清 | 好男人电影高清在线观看| 人妻 亚洲 视频| 69av精品久久久久久 | 亚洲激情五月婷婷啪啪| 国产激情久久老熟女| 美女国产高潮福利片在线看| 成年动漫av网址| 免费人妻精品一区二区三区视频| 国产亚洲欧美精品永久| 一区二区三区激情视频| 19禁男女啪啪无遮挡网站| 久久精品久久久久久噜噜老黄| 欧美少妇被猛烈插入视频| 欧美日韩av久久| 99国产精品免费福利视频| 久久久久久亚洲精品国产蜜桃av| 丝袜脚勾引网站| 国产三级黄色录像| 国产亚洲午夜精品一区二区久久| 美女视频免费永久观看网站| 岛国毛片在线播放| 中文欧美无线码| 国产男女内射视频| 国产精品一二三区在线看| 国产在线免费精品| 免费观看a级毛片全部| 久久人人爽av亚洲精品天堂| 天堂俺去俺来也www色官网| 另类亚洲欧美激情| 老鸭窝网址在线观看| 国产成人一区二区三区免费视频网站| 黄色毛片三级朝国网站| av在线老鸭窝| 国产亚洲精品久久久久5区| 国产成人啪精品午夜网站| 午夜免费成人在线视频| 一进一出抽搐动态| 亚洲精品中文字幕在线视频| 久久九九热精品免费| 国产在视频线精品| 成人免费观看视频高清| 丁香六月欧美| 国产在线免费精品| 窝窝影院91人妻| 精品一品国产午夜福利视频| 777米奇影视久久| 久久人人97超碰香蕉20202| 成年人黄色毛片网站| 777久久人妻少妇嫩草av网站| 成人免费观看视频高清| 9色porny在线观看| 精品乱码久久久久久99久播| 国产日韩一区二区三区精品不卡| 国产精品香港三级国产av潘金莲| 十分钟在线观看高清视频www| 国产无遮挡羞羞视频在线观看| 51午夜福利影视在线观看| netflix在线观看网站| www.999成人在线观看| 欧美精品av麻豆av| 精品人妻在线不人妻| av又黄又爽大尺度在线免费看| 老熟妇仑乱视频hdxx| 色精品久久人妻99蜜桃| 久久久久国产精品人妻一区二区| 少妇裸体淫交视频免费看高清 | 亚洲视频免费观看视频| 欧美另类一区| 两个人免费观看高清视频| 精品久久蜜臀av无| 欧美在线黄色| av又黄又爽大尺度在线免费看| 久久人人97超碰香蕉20202| 亚洲天堂av无毛| 午夜两性在线视频| 久久性视频一级片| 一区二区三区激情视频| 超色免费av| 亚洲专区国产一区二区| 电影成人av| 成年人午夜在线观看视频| 狠狠婷婷综合久久久久久88av| 久久99热这里只频精品6学生| 国产精品香港三级国产av潘金莲| 99热网站在线观看| 日本91视频免费播放| 日韩制服骚丝袜av| 国产精品影院久久| 少妇人妻久久综合中文| 极品少妇高潮喷水抽搐| 色婷婷av一区二区三区视频| 日本五十路高清| 精品国产乱码久久久久久小说| 国产精品一区二区精品视频观看| 黑丝袜美女国产一区| 亚洲中文日韩欧美视频| 天天添夜夜摸| 高清欧美精品videossex| 国产一区二区三区在线臀色熟女 | 欧美激情高清一区二区三区| 精品卡一卡二卡四卡免费| videosex国产| 精品卡一卡二卡四卡免费| videosex国产| 搡老熟女国产l中国老女人| 日韩视频一区二区在线观看| 在线观看舔阴道视频| 国产一区二区三区在线臀色熟女 | 欧美xxⅹ黑人| 久久久久网色| 精品福利永久在线观看| 久久国产精品影院| 91国产中文字幕| 久久久精品区二区三区| 麻豆国产av国片精品| 动漫黄色视频在线观看| 国产av又大| 国产一级毛片在线| 女警被强在线播放| 日韩欧美国产一区二区入口| 两人在一起打扑克的视频| 日本五十路高清| 色婷婷av一区二区三区视频| 国产一区有黄有色的免费视频| 国产精品秋霞免费鲁丝片| 久久久久久久国产电影| bbb黄色大片| 999久久久国产精品视频| 女警被强在线播放| 精品亚洲成a人片在线观看| 少妇人妻久久综合中文| 午夜影院在线不卡| 大片电影免费在线观看免费| 另类亚洲欧美激情| 人人澡人人妻人| 十八禁网站网址无遮挡| 热re99久久国产66热| 免费高清在线观看日韩| 亚洲va日本ⅴa欧美va伊人久久 | 久久国产亚洲av麻豆专区| 欧美日韩中文字幕国产精品一区二区三区 | 久久久久国产一级毛片高清牌| 极品少妇高潮喷水抽搐| 大码成人一级视频| 午夜福利一区二区在线看| 多毛熟女@视频| 国产精品久久久人人做人人爽| 欧美另类亚洲清纯唯美| 91麻豆精品激情在线观看国产 | www.av在线官网国产| 日日夜夜操网爽| 性高湖久久久久久久久免费观看| 真人做人爱边吃奶动态| 久久人妻福利社区极品人妻图片| 丰满少妇做爰视频| 日本a在线网址| 一区二区三区乱码不卡18| 黄频高清免费视频| 手机成人av网站| 亚洲一区二区三区欧美精品| 久久久久久免费高清国产稀缺| 久久性视频一级片| 狠狠精品人妻久久久久久综合| 69精品国产乱码久久久| 极品少妇高潮喷水抽搐| 久久久国产一区二区| 国产主播在线观看一区二区| 久久久久久久久免费视频了| 久久久国产精品麻豆| 亚洲欧美一区二区三区久久| 69av精品久久久久久 | 他把我摸到了高潮在线观看 | 一级黄色大片毛片| 后天国语完整版免费观看| 午夜精品国产一区二区电影| 最新在线观看一区二区三区| 久久狼人影院| 两个人看的免费小视频| 久久久国产精品麻豆| 国产成人a∨麻豆精品| 亚洲国产精品999| 欧美另类一区| 午夜福利一区二区在线看| 亚洲avbb在线观看| 欧美精品高潮呻吟av久久| 精品一区二区三区四区五区乱码| 秋霞在线观看毛片| cao死你这个sao货| 欧美人与性动交α欧美软件| 精品久久久久久久毛片微露脸 | 伊人久久大香线蕉亚洲五| 中文字幕另类日韩欧美亚洲嫩草| 人妻人人澡人人爽人人| 老鸭窝网址在线观看| 天堂俺去俺来也www色官网| 成年人黄色毛片网站| 午夜精品国产一区二区电影| 少妇的丰满在线观看| 久久久精品免费免费高清| 久久午夜综合久久蜜桃| 国产精品.久久久| 一本大道久久a久久精品| 国产福利在线免费观看视频| 一区二区三区激情视频| 久久这里只有精品19| 免费少妇av软件| 欧美精品av麻豆av| 亚洲中文av在线| 亚洲欧美清纯卡通| av超薄肉色丝袜交足视频| 性色av一级| 三级毛片av免费| 国产日韩欧美在线精品| 国产日韩一区二区三区精品不卡| 欧美日本中文国产一区发布| 亚洲专区字幕在线| 亚洲精品久久久久久婷婷小说| 亚洲精品在线美女| 日本vs欧美在线观看视频| 男人添女人高潮全过程视频| 制服人妻中文乱码| 国产成人精品在线电影| 欧美日韩av久久| 香蕉国产在线看| 亚洲伊人色综图| 久久久久国产一级毛片高清牌| av欧美777| 黑人猛操日本美女一级片| 国产欧美日韩精品亚洲av| 色播在线永久视频| 永久免费av网站大全| 亚洲精品成人av观看孕妇| 一区在线观看完整版| videos熟女内射| 久久久精品94久久精品| 国产精品.久久久| 欧美精品啪啪一区二区三区 | 午夜福利影视在线免费观看| 中国美女看黄片| 在线亚洲精品国产二区图片欧美| 国产成人一区二区三区免费视频网站| 丝袜喷水一区| 日本猛色少妇xxxxx猛交久久| kizo精华| 99国产精品99久久久久| 啪啪无遮挡十八禁网站| 午夜视频精品福利| 老司机福利观看| 亚洲成av片中文字幕在线观看| 国产成人a∨麻豆精品| 大型av网站在线播放| 国产精品久久久久久精品古装| 欧美日韩一级在线毛片| 国产真人三级小视频在线观看| 高清在线国产一区| 午夜福利免费观看在线| a级毛片黄视频| 波多野结衣一区麻豆| 丝袜喷水一区| 青青草视频在线视频观看| 黄色视频,在线免费观看| 亚洲专区国产一区二区| 国产精品秋霞免费鲁丝片| h视频一区二区三区| 久久久久久久精品精品| 性色av乱码一区二区三区2| 天堂俺去俺来也www色官网| 亚洲伊人久久精品综合| 久久久欧美国产精品| 丝袜美足系列| 亚洲国产欧美一区二区综合| 三上悠亚av全集在线观看| 成人三级做爰电影| 啦啦啦 在线观看视频| 在线 av 中文字幕| 中文字幕人妻熟女乱码| 亚洲国产看品久久| 久久久久久久精品精品| 国产福利在线免费观看视频| 久久久久久人人人人人| 国产男女内射视频| 欧美日韩中文字幕国产精品一区二区三区 | 人人妻人人添人人爽欧美一区卜| 亚洲精品美女久久av网站| 在线十欧美十亚洲十日本专区| 亚洲av国产av综合av卡| 午夜免费成人在线视频| 中国国产av一级| 99国产综合亚洲精品| 一级黄色大片毛片| 色婷婷av一区二区三区视频| 国产欧美日韩一区二区三 | 亚洲男人天堂网一区| 丰满少妇做爰视频| 十八禁人妻一区二区| 99国产极品粉嫩在线观看| svipshipincom国产片| 色94色欧美一区二区| 亚洲欧美日韩另类电影网站| 亚洲av男天堂| 欧美黑人欧美精品刺激| 色婷婷久久久亚洲欧美| 在线观看免费午夜福利视频| 成年动漫av网址| 中文字幕高清在线视频| 又大又爽又粗| videos熟女内射| 青青草视频在线视频观看| 亚洲精品中文字幕一二三四区 | 日本精品一区二区三区蜜桃| 亚洲专区字幕在线| 亚洲熟女精品中文字幕| 美女中出高潮动态图| 窝窝影院91人妻| av超薄肉色丝袜交足视频| 乱人伦中国视频| 亚洲国产精品一区三区| 日韩欧美免费精品| 丝袜在线中文字幕| 日本猛色少妇xxxxx猛交久久| 日韩,欧美,国产一区二区三区| 两性午夜刺激爽爽歪歪视频在线观看 | 老司机深夜福利视频在线观看 | 亚洲少妇的诱惑av| 国产精品一区二区在线不卡| 免费观看av网站的网址| 每晚都被弄得嗷嗷叫到高潮| √禁漫天堂资源中文www| 日韩视频一区二区在线观看| 精品国产超薄肉色丝袜足j| 自拍欧美九色日韩亚洲蝌蚪91| www.999成人在线观看| 老熟妇乱子伦视频在线观看 | 亚洲成人免费电影在线观看| 成人国语在线视频| 亚洲精品美女久久av网站| 黄色视频在线播放观看不卡| 精品久久久久久电影网| 99精品欧美一区二区三区四区| 中文字幕精品免费在线观看视频| 国产精品偷伦视频观看了| 天天影视国产精品| 99国产精品99久久久久| 超色免费av| 精品一区二区三卡| 午夜日韩欧美国产| 亚洲美女黄色视频免费看| 国产精品香港三级国产av潘金莲| 黄色毛片三级朝国网站| 十八禁人妻一区二区| 在线观看一区二区三区激情| 精品国内亚洲2022精品成人 | 久久亚洲精品不卡| 午夜日韩欧美国产| 久久九九热精品免费| 在线观看免费视频网站a站| 丰满少妇做爰视频| 成人黄色视频免费在线看| h视频一区二区三区| 精品久久久精品久久久| 久久久国产成人免费| 国产又色又爽无遮挡免| 不卡av一区二区三区| 国产麻豆69| 精品人妻熟女毛片av久久网站| 美女国产高潮福利片在线看|