• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Research on deformation mechanism of AZ31 magnesium alloy sheet with non-basal texture during uniaxial tension at room temperature:A visco-plastic self-consistent analysis

    2022-09-26 03:09:22LiHuHuyunLvLixinShiYuChenQingChenToZhouMingoLiMingoYng
    Journal of Magnesium and Alloys 2022年7期

    Li Hu,Huyun Lv,Lixin Shi,*,Yu Chen,Qing Chen,To Zhou,*,Mingo Li,Mingo Yng

    aCollege of Material Science and Engineering,Chongqing University of Technology,Chongqing 400054,China

    b Southwest Technology and Engineering Research Institute,Chongqing 400039,China

    Abstract The relationship between activities of involved deformation mechanisms and the evolution of microstructure and texture during uniaxial tension of AZ31 magnesium alloy with a rare non-basal texture has been thoroughly investigated in the present study by means of electron backscattered diffraction(EBSD)measurement and visco-plastic self-consistent(VPSC)modeling.These results show that except basalslip and prismaticslip,{10ˉ12}extension twin(ET)also plays a significant role during plastic deformation.With the increasing tilted angle between loading direction and rolling direction(RD)of sheet,the activity of{10ˉ12}ET possesses a decreasing tendency and its role in plastic deformation changes from the one mainly sustaining plastic strain to the one mainly accommodating local strain between individual grains.When{10ˉ12}ET serves as a carrier of plastic strain,it mainly results in the formation of basal texture component(c-axis//ND,normal direction).By comparison,when the role of{10ˉ12}ET is to accommodate local strain,it mainly brings about the formation of prismatic texture component(c-axis//TD,transverse direction).At large plastic deformation,the competition between basalslip and pyramidalslip is responsible for the concentration of tilted basal poles towards ND within all deformed samples.The larger difference is between the activities of basalslip and pyramidalslip,the smaller separation is between these two tilted basal poles.Besides,VPSC modeling overestimates volume fractions of{10ˉ12}ET in samples with angle of 0 to 30° between loading direction and RD of sheet because interactions between twin variants are not included in VPSC modeling procedure at the present form.In addition,as compatible deformation between individual grains cannot be considered in VPSC modeling,the predicted volume fractions of{10ˉ12}ET in samples with angle of 45 to 90° between loading direction and RD of sheet are smaller than the correspondingly measured results.? 2021 Chongqing University.Publishing services provided by Elsevier B.V.on behalf of KeAi Communications Co.Ltd.This is an open access article under the CC BY-NC-ND license(http://creativecommons.org/licenses/by-nc-nd/4.0/)

    Keywords:AZ31 magnesium alloy;Non-basal texture;Plastic deformation;VPSC.

    1.Introduction

    Owing to their remarkably low density,high specific stiffness and strength,magnesium alloys have long been treated as a promising light-weight material to tackle the increasingly serious energy crisis.However,the widespread applications of magnesium alloys are still hindered by industrial practitioners because of their poor formability at room temperature[1].In fact,this shortcoming originates from the intrinsic characteristics of hexagonal close-packed(HCP)structure in magnesium alloys,which leads to the limited slip systems[2].Extensive research has confirmed that basalslip{0001}<11ˉ20>and prismaticslip{10ˉ10}<11ˉ20>can only sustain the plastic strain perpendicular to thec-axis of grains and provide only two independent slip systems each.Therefore,they cannot accommodate all the strains for polycrystalline plasticity since at least five independent slip systems are needed during plastic deformation of metallic materials,which is called the von Mises condition[3].Additional deformation mode,namely pyramidalslip{11ˉ22}<11ˉ23>or{10ˉ12}extension twin(ET),has to participate in the plastic deformation and accommodate the plastic strain along thec-axis of grains[4].Moreover,{10ˉ11}compression twin(CT)has also been observed during plastic deformation of magnesium alloys and it is closely related to texture softening,reduction of work hardening rate,strain concentration and early failure or fracture of deformed samples[5,6].Given the aforementioned complex deformation mechanisms in magnesium alloys,the detailed understanding of roles of various deformation mechanisms during plastic strain is of great necessity to guide the design of ductile magnesium alloys and further broaden the correspondingly industrial applications.

    Over the past few decades,numerous investigations,especially the ones with the assistance of experimental measurement and/or crystal plasticity modeling,have attempted to identify,quantify or clarify the contribution and significance of various deformation mechanisms that lead to the complex deformation behavior of magnesium alloys under different strain paths.For instance,Chapuis et al.[7]and Wang et al.[8]confirmed that the in-plane tensile behavior of AZ31 magnesium alloy sheet is mainly accommodated by basalslip and prismaticslip.In comparison,Guo et al.[9]reported that the through-thickness tensile deformation of AZ31 magnesium alloy is sustained by not only basalslip and prismaticslip but also{10ˉ12}ET.In addition,Wang et al.[10]studied the uniaxial compression behavior of AZ31 magnesium alloy along normal direction(ND)and transverse direction(TD).Their investigation claimed that{10ˉ12}ET occurs at the onset of plastic deformation and quickly grows to consume the parent grains,whereas{10ˉ11}CT also nucleates at the early stage of plastic strain and then multiplies in the grains reoriented by{10ˉ12}ET.Besides,Agnew et al.[11]investigated the role of pyramidalslip during through-thickness compression of AZ31 magnesium alloy and confirmed that pyramidalslip serves as the second most active deformation mechanism after basalslip.However,it is worth noting that these foregoing investigations are mainly limited to magnesium alloys with typical basal texture,which is usually formed during the rolling process of fabricating sheet.As for magnesium alloys with non-basal texture,the focus of current research mainly lays on how to tailor the initial basal texture.For example,Kuang et al.[12]fabricated the AZ31 magnesium alloy sheet with TD-split bimodal texture by using single pass large strain electro-plastic rolling(LSER).He et al.[13]successfully introduced an orthogonal four-peak distribution of basal texture in the fabricated AZ31 magnesium alloy sheet by applying in-plane pre-compression,pre-stretching and annealing treatment.Study on the effects of non-basal texture on mechanical properties and/or formability of magnesium alloys are seldom reported,let along the relationship between microstructure evolution and the corresponding activities of deformation mechanisms during plastic deformation[14].

    Therefore,the current investigation aims at elucidating relationship between microstructure evolution and activities of involved deformation mechanisms in magnesium alloy with non-basal texture.The adopted material in the present study is AZ31 magnesium alloy sheet fabricated by the newly developed processing technology,viz.equal channel angular rolling and continuous bending process with subsequent annealing(ECAR-CB-A).Texture characterization convinced that this manufactured AZ31 magnesium alloy sheet is with a rare non-basal texture,whose two basal poles tilt about±40°away from ND to rolling direction(RD)[14,15].Uniaxial tension experiments along different loading directions at room temperature are then conducted and these deformed samples are characterized by means of electron backscattered diffraction(EBSD)measurement.Subsequently,numerical investigation by using the visco-plastic self-consistent(VPSC)model is performed to correlate activities of deformation mechanisms with microstructure evolution.It has been generally accepted that among these reported crystal plasticity models,VPSC model developed by Lebensohn and Toméhas been termed as a most popular one due to its high forecasting accuracy,extraordinary computation efficiency and outstanding robustness in algorithms[17,18].

    2.Experimental and modeling procedures

    2.1.Uniaxial tension experiments and microstructure characterization

    In the present study,AZ31 magnesium sheet with nonbasal texture was manufactured by the ECAR-CB-A process.The detailed processing procedures and processing parameters about the ECAR-CB-A process have been well documented in the work of Tu et al.[15].Then,dog-bone shaped specimens with the gauge length of 22.5mm and cross-section of 6mm×1.2mm were taken from the fabricated AZ31 magnesium sheet via electro-discharge machining(EDM).The corresponding sampling strategy is depicted in Fig.1,where the angles between gauge direction and RD of sheet are identified to be 0,30,45,60 and 90°.Tensile tests were hereafter performed on a SANS testing machine at a constant strain rate of 0.001s-1and at room temperature.The deformation degree was chosen to be 6 and 12%.To be concise in the following sections,these samples deformed in uniaxial tension would be called UT-0° sample,UT-30° sample,UT-45°sample,UT-60° sample and UT-90° sample,respectively.

    Evolution of microstructure and texture within all undeformed and deformed samples were characterized on the RDTD planes by means of EBSD measurement.The corresponding aspect about sample preparation is as follows:RD-TD planes of these samples are mechanically polished by using 1200-grit SiC paper and then electro-polished in ACII electrolyte.The corresponding components of this solution include 50ml C3H8O,37.5g C6H8O7·H2O,20.75g NaCNS,400ml C2H6O,5g C9H7NO,9ml H2O and 7.5ml HClO4.

    Fig.1.Schematic illustration of sampling strategy for tension specimens with different tilted angles between the gauge direction and RD of sheet.

    Fig.2.Microstructure and texture of undeformed sample:(a)Inverse pole figure(IPF)map;(b)Grain boundaries(GB)map;(c)(0002),(10ˉ10)and(10ˉ11)pole figures.

    The duration time of electrolytic polishing,polishing voltage and current were chosen to be 180s,20V and 0.03A,respectively.Afterwards,EBSD investigation was performed on a FEI Nova 400 scanning electron microscope equipped with an HKL-Nordlys Max detector.To obtain a good indexing quality,a relatively large step size of 2.0μm is adopted for the undeformed sample in the present study,while a relatively small step size of 1.5μm is applied for these deformed samples.All EBSD data were further post-processed with the assistance of Channel 5 analysis software and MTEX toolbox[19].The corresponding microstructure and texture of undeformed sample is shown in Fig.2,which includes the inverse pole figure(IPF)map,grain boundaries(GB)map and pole figures.It is obvious that the fabricated AZ31 magnesium sheet possesses a rare non-basal texture with two tilted basal poles away from ND to RD.The grain morphology in Fig.2(a)is with typical characteristic of equiaxed microstructure and the average grain size is identified to be 14.45μm.Moreover,Fig.2(b)demonstrate that the microstructure of undeformed sample is nearly twin-free and has a few low angle boundaries(LABs)whose misorientation ranges from 2 to 15°.All these aforementioned observations are quite consistent with the reported results in Chen et al.[14]and Song et al.[16].

    2.2.VPSC-based crystal plasticity modeling

    VPSC model is applied to simulate the plastic deformation behavior of AZ31 magnesium alloy with a rare non-basal texture during uniaxial tension tests.Some complete descriptions of VPSC model are available in the literature[17,20].In fact,VPSC model possesses the capability to account for not only the anisotropy of properties in single grain but also the anisotropy of properties in polycrystalline aggregate.The constitutive behavior at grain level is described by a non-linear rate-sensitivity equation as follows:

    where˙εijandσklstand for the correspondingly deviatoric strain rate and stress.˙γ0servers as a normalization factor and is set to the macroscopic strain rate of 0.001s-1.The exponent n reflects the rate-sensitivity and a value of 20 is adopted in the present study to simulate plastic deformation of HCP materials,as advised in the VPSC manual.In addition,refers to the Schmid tensor associated with slip and twinning modes,and it can be calculated on the basis of normal vector(ns)and Burgers vector(bs).τsis the critical revolved shear stress(CRSS)on specific slip/twinning mode.The corresponding evolution ofτsis associated with accumulated shear strain(Γ)for individual deformation mechanisms and can be described by the following extended Voce equation.

    whereτ0,τ1,θ0,θ1stand for adjustable parameters which control the hardening behavior of each deformation mode.In addition,VPSC model takes into account the hardening effect,which results from the interaction between different deformation mechanisms.Therefore,a coupling coefficient hss′is introduced to reflect these interactions by the following equation:

    where hss′stands for the self-hardening coefficient when s=s′,whereas hss′infers to the latent-hardening coefficient when s/=s′.Δτsequals to the increment of CRSS in a slip/twinning mode.

    To model the contribution of twin to texture development and track the evolution of twin volume fraction,the predominant twin reorientation(PTR)scheme proposed by Toméet al.[21]has been successfully embedded into VPSC code.The principle of PTR scheme is as follows:At each incremental step,by comparing the accumulated twin volume in each grain with a threshold value Vthres,whether or not a given grain should be reoriented can be determined by the following equation:

    where Ath1and Ath2are two artificial material constants and they are associated with the evolution of twin volume fraction in different twining modes.The proposal of Chapuis et al.[22]is as follows:for{10ˉ12}ET,the values of Ath1and Ath2are 0.7 and 0.1,whereas for{10ˉ11}CT,the values of Ath1and Ath2are 0.05 and 0.05.Moreover,Veffand Vaccumrefer to the effective twin fraction and the accumulative twin fraction in a grain,respectively.

    Fig.3.Comparison between experimental stress-strain curve and the correspondingly predicted one of AZ31 magnesium alloy with a rare non-basal texture under uniaxial tension along RD of sheet(The initial texture obtained by EBSD measurement and by discretizing the ODF are also included).

    In the present study,plastic deformation of AZ31 magnesium alloy is assumed to be accommodated by basalslip,prismaticslip,pyramidalslip,{10ˉ12}ET and{10ˉ11}CT.These involved deformation mechanisms would lead to great difficulty about parameter identification in VPSC model because at least 12 material parameters would be needed in simulating plastic deformation of magnesium alloy[23].Therefore,a minimum parameter approach proposed by Hutchinson et al.[23]has been adopted in the present study.Only a measured true stress-strain curve of uniaxial tension along RD of sheet,as shown in Fig.3,has been used to verify the material parameters in VPSC model.These fitted material parameters are exhibited in Table 1,where the fundamental CRSS values are obtained by taking an approximate average of reported results of single crystal tests[23–26].Obviously,the predicted true stress-strain curve agrees well with the measured result.Though only a few material parameters are included,Chen et al.[27]reported that these predicted texture evolution and activities of deformation mechanisms by using a minimum parameter approach are acceptable when simulating plastic deformation behavior of AZ31 magnesium alloy.Lastly,in order to get accurate simulation results by using VPSC model,it is important to obtain an appropriate input data of initial orientations,which can reflect the texture characteristics of as-received AZ31 magnesium alloy sheet with a rare non-basal texture.This issue can be handled by discretizing the orientation distribution function(ODF)of measured EBSD data with the help of MTEX toolbox.The specific contents about orientation discretization can be found in[28,29].From Fig.3,it is obvious that(0002)and(10ˉ10)pole figures based on the extracted 5000 orientations shows high consistency with respect to the corresponding ones on account of EBSD data.

    3.Results

    3.1.Measured and predicted texture evolution during uniaxial tension

    Fig.4 compares the measured and predicted texture evolution of various samples along different loading directions during uniaxial tension.It is obvious that these predicted(0002)pole figures show good accordance with the measured ones at both deformation degree of 6 and 12%.This aspect further confirms the validity of the fitted material parameters in the present study.In addition,it can be found that with the progression of plastic strain,a new TD-component texture(caxis//TD)marked by white dash box gradually appears within all deformed samples,especially for the UT-0° sample.Chen et al.[14]have also reported this phenomenon and concluded that this dramatic texture change surely arises from the con-tribution of activated{10ˉ12}ET within deformed samples.Moreover,along with the increase of tilted angle between loading direction and RD of sheet,there exists an apparently weakened tendency about the concentration of tilted basal poles towards ND.This observation can further be verified by comparing the correspondingly measured and predicted results about the separated angles between two points with maximum pole density in tilted basal poles,as shown Table 2.On the one side,the predicted results show minor differences by comparison with the correspondingly measured ones.For example,the measured and predicted results about separated angles are 71.3 and 70.5° at deformation degree of 6%,55.6 and 56.2° at deformation degree of 12%.On the other side,these measured differences(Δθ)between the separated angles in the case of deformation degree of 6 and 12% decrease from 15.7 to 4.7°,while the correspondingly predicted ones also decrease from 14.3 to 2.2°.These observations apparently show a decreasing tendency about the difference(Δθ)with the increasing tilted angle between loading direction and RD of sheet.

    Table 1Material parameters of VPSC model with a minimum parameter approach.

    Table 2The measured and predicted results about separated angles between two points with maximum pole density in tilted basal poles at different deformation degree and the corresponding difference(Δθ).

    3.2.Measured and predicted microstructure evolution during uniaxial tension

    Figs.5 and 6 are composed of IPF maps and depict the microstructure evolution of all 6%-deformed samples and 12%-deformed samples along different loading directions during uniaxial tension.As Chen et al.[14]have reported that{10ˉ12}ET is identified to be the dominant twinning mechanism during plastic deformation of AZ31 magnesium alloy sheet with a rare non-basal texture,in the present study{10ˉ12}ETs are also be focused on and are highlighted by bright color,while the rest is being partly greyed out.It is obvious that loading direction has an important influence on the activation of{10ˉ12}ET during uniaxial tension.The amount of{10ˉ12}ET possesses a decreasing tendency along with the increasing tilted angle between loading direction and RD of sheet.This aspect can further be verified by the correspondingly calculated volume fractions of{10ˉ12}ET within deformed samples,as shown in Table 3.As for UT-0° sample,it contains the largest volume fractions of{10ˉ12}ET within both 6%-deformed sample(0.161)and 12%-deformed sample(0.204).By comparison,UT-90° sample only possesses the minimal volume fractions of{10ˉ12}ET at both 6%-deformed sample(0.045)and 12%-deformed sample(0.068).Moreover,the predicted evolution of volume fraction about{10ˉ12}ET is calculated and shown in Fig.7,where these experimental values are also included and plotted by polygons with different colors.In all deformed samples,the predicted volume fractions of{10ˉ12}ET overall increase with the progression of plastic strain.However,the larger is the tilted angle between loading direction and RD of sheet,the smaller is the predicted volume fraction of{10ˉ12}ET.In addition,it is worth noting in Fig.7 that all deformed samples can be classified into two categories:these(UT-0° sample and UT-30° sample)overestimating the volume fractions of{10ˉ12}ET in numerical investigation and these(UT-45° sample,UT-60° sample and UT-90° sample)underestimating the volume fractions of{10ˉ12}ET in numerical investigation.

    Table 3Measured volume fractions of{10ˉ12}ET within all deformed samples during uniaxial tension along different loading directions.

    4.Discussion

    4.1.Effect of loading direction on predicted activities of deformation mechanisms

    Fig.4.(0002)pole figures showing the comparison between measured and predicted texture evolution of various samples along different loading directions during uniaxial tension at room temperature:(a)UT-0° sample;(b)UT-30° sample,(c)UT-45° sample;(d)UT-60° sample,(e)UT-90° sample.(TD-component texture marked by white dash box emerges near the TD of sheet with the increasing plastic strain).

    Fig.5.IPF maps of 6%-deformed samples along various loading directions during uniaxial tension at room temperature:(a)UT-0° sample;(b)UT-30° sample;(c)UT-45° sample;(d)UT-60° sample;(e)UT-90° sample.

    Fig.8 demonstrates the predicted slip and twinning activities of various samples during uniaxial tension.As plastic strain instead of deformation degree is applied in VPSC model,translation equation ofεplasticstrain=ln(1+εengineeringstrain)is adopted for uniaxial tension deformation and the corresponding plastic strain values with respect to 6 and 12% deformation degree are calculated to be 0.058 and 0.113,respectively.It can be seen from Fig.8 that as for the twinning modes,{10ˉ12}ET largely participates in the plastic deformation at the onset of uniaxial tension(to plastic strain of 0.03),afterwards its contribution is gradually weakening with the increasing plastic strain.It has been generally accepted that{10ˉ12}ET can accommodate plastic strain along thec-axis of grains and possesses the smallest CRSS by comparison with other deformation mechanisms except for basalslip[30,31].Consequently,it possesses a relatively large amount of activation at early stage of plastic deformation.Moreover,as the tilted angle between thec-axis of most grains and loading direction increases from about 50° in UT-0° sample to nearly 90° in UT-90° sample,the elongation along thec-axis is extensively prohibited[18].This aspect leads to the reduced contribution of{10ˉ12}ET,as shown in Fig.8.In terms of{10ˉ11}CT,its activities only maintain at a low level and contribute very small to the plastic deformation within all deformed samples.

    As for the slip modes,with the progression of plastic strain,the predicted activities of prismaticslip are gradually enhanced,while the predicted activities of basalslip possess a decreasing tendency.This aforementioned observation can be further verified by analyzing the Schmid factor(SF)of each slip mode,which indicates the difficulty of activation during plastic deformation.Based on the EBSD data of all samples,the corresponding results of statistical analysis about SF are shown in Fig.9 and Table 4.As for basalslip,during deformation the percentage of SF value in the rage of 0.3–0.5 and the average SF value both possess a decreasing tendency along with the increasing tilted angle between loading direction and RD of sheet.With respect to prismaticslip,the percentage of SF value in the rage of 0.3–0.5 and the average SF value both exhibit an increasing tendency along with the increasing tilted angle between loading direction and RD of sheet.Besides,Fig.8 demonstrates that basalslip and prismaticslip are two dominant deformation mechanisms for AZ31 magnesium alloy with a rare non-basal texture during uniaxial tension along different loading directions.This phenomenon also occurs in AZ31 magnesium alloy with typical basal texture during in-plane uniaxial tension,as reported by Agnew et al.[11]and Chapuis et al.[22].However,the loading direction has an obvious impact on the contribution of basalslip and prismaticslip to plastic strain.Fig.8 depicts that in UT-0°sample,basalslip is the most important slip mode during plastic deformation,and prismaticslip serves as the secondary one.However,along with the increasing tilted angle between loading direction and RD of sheet,prismaticslip begins to sustain more plastic strain by comparison with basalslip.Clearly,prismaticslip,not basalslip,has been turned into the prominent deformation mechanism in UT-90° sample.Lastly,it is interesting to find in Fig.8 that the predicted activities of pyramidalslip grow gradually with the increasing tilted angle between loading direction and RD of sheet.This issue seems to be contradictory to the correspondingly statistical analysis of SF value in Fig.9 and Table 4,where there only exists minor change about the percentage of SF value in the rage of 0.3–0.5 and the average SF value.Generally speaking,pyramidalslip would be activated with difficulty at room temperature due to its large CRSS and it mainly serves as a compatibility deformation mechanism for magnesium alloys[32,33].In the present study,along with the increasing tilted angle between loading direction and RD of sheet,the reduced activities in{10ˉ12}ET would hinder the plastic strain along thec-axis of grains.Consequently,pyramidalslip has to be activated more frequently in order to satisfy the necessity of deformation along thec-axis of grains.

    Fig.6.IPF maps of 12%-deformed samples along various loading directions during uniaxial tension at room temperature:(a)UT-0° sample;(b)UT-30°sample;(c)UT-45° sample;(d)UT-60° sample;(e)UT-90° sample.

    Table 4The average SF values of basalslip,prismaticslip and pyramidalslip within five samples during uniaxial tension.

    Fig.7.Predicted volume fractions of{10ˉ12}ET for all tensile samples.(Experimental volume fractions of{10ˉ12}ET at deformation degree of 6 and 12% are included and plotted by polygons with different colors).

    4.2.Contribution of involved deformation mechanisms to texture evolution

    To date numerous investigations have been conducted in order to elucidate the roles of various deformation mechanisms to texture evolution of magnesium alloys during uniaxial tension and a consensus has been arrived over this issue[14,33–35]:the activities of basalslip and{10ˉ12}ET are beneficial for rotating ofc-axis of grains towards ND,whereas the motion of pyramidalslip leads to the rotation ofc-axis of grains towards loading direction during uniaxial tension.Moreover,prismaticslip mainly results in a rotation of grains around theirc-axis and{10ˉ11}CT only provides slight contribution to the plastic strain as well as texture evolution.Consequently,the observed phenomenon about texture evolution shown in Fig 4 should be collectively ascribed to the activities of basalslip,{10ˉ12}ET and pyramidalslip.To more precisely assess the relationship between the activities of involved deformation mechanisms and the corresponding texture evolution in the present study,grain orientations obtained from VPSC modeling are further divided into two classes.One of them possesses misorientations(larger than 60°)with respect to the correspondingly initial orientations.The other contains the remaining orientations in the predicted results.Clearly,the former class is mainly ascribed to the activation of{10ˉ12}ET which could result in the rotation around its<1ˉ210>axis by about 86.3°.In addition,the latter class is attributed to the joint action of remaining deformation mechanisms,especially for basalslip and pyramidalslip.Finally,the corresponding(0002)pole figures,which are based on these two groups of orientations,are constructed and shown in Fig.10 and Fig.11,respectively.It is obvious in Fig.10(a)that at deformation degree of 6%,{10ˉ12}ETs within UT-0° sample mainly contribute to the formation of basal texture component(c-axis//ND)and its role in the formation of prismatic texture component(c-axis//TD)is negligible.Along with the increasing tilted angle between loading direction and RD of sheet,the density of basal texture component is gradually reduced and the density of prismatic texture component is gradually enhanced.Especially in UT-90° sample,{10ˉ12}ETs mainly bring about the formation of prismatic texture component.Meanwhile,Fig.11(a)depicts that the collective action of involved deformation mechanisms except for{10ˉ12}ET actually results in a negligible change of texture.This observation is mainly ascribed to the fact that dislocation slip would only result in a gradual change of texture[14].Considering that at early stage of plastic deformation,there exists relatively large amount of activities of{10ˉ12}ET within UT-0°sample and UT-30° sample,as shown in Fig.8,it can be concluded that the concentration of tilted basal poles towards ND within these samples should be mainly ascribed to the contribution of{10ˉ12}ET.With the progression of plastic strain,the role of{10ˉ12}ET to the formation of prismatic texture component are gradually enhanced within all deformed samples.Fig.10(c)shows that at deformation degree of 21%,{10ˉ12}ET apparently results in a strong prismatic texture component and a weak basal texture component within all deformed samples.These observations provide strong evidence that in the case of large plastic deformation,{10ˉ12}ET has little influence on the concentration of tilted basal poles towards ND in(0002)pole figure.However,Fig.11(b)and(c)demonstrate that within UT-0° sample and UT-30° sample there still exists observable phenomenon about the concentration of tilted basal poles towards ND,while these exists negligible change about the separation of two tilted basal poles within the remaining samples.Given consideration that the activity of basalslip is substantially larger than the one of pyramidalslip within UT-0° sample and UT-30° sample,as shown in Fig.8,the concentration effect resulted from basalslip should be far better than the splitting effect derived from pyramidalslip.This aspect finally results an observable concentration of tilted basal poles towards ND in(0002)pole figure at large plastic strain.In terms of UT-90° sample,Fig.8 depicts that there exists relatively small difference between the activities of basalslip and pyramidalslip.Accordingly,the concentration effect resulted from basalslip should be largely offset by the splitting effect derived from pyramidalslip.This aspect finally brings about a negligible concentration of tilted basal poles towards ND in(0002)pole figure.

    Fig.8.Predicted slip and twinning activities of various samples during uniaxial tension:(a)UT-0° sample;(b)UT-30° sample,(c)UT-45° sample;(d)UT-60°sample,(e)UT-90° sample.

    4.3.Effect of twin variant on predicted volume fraction of{101ˉ2}ET

    From Figs.5 and 6,it can be seen that{10ˉ12}ET plays an important role on the microstructure evolution of AZ31 magnesium alloy with a rare non-basal texture during uniaxial tension.Although its role on texture evolution can be effectively predicted,there exists some difference between the measured volume fractions of{10ˉ12}ET and the correspondingly predicted ones,as shown in Fig.7.In fact,it is well known that there are six twin variants of{10ˉ12}ET in magnesium alloys during plastic deformation and the selective activation of various twin variants is extensively dependent on the strain path[36].To further investigate the twinning behavior and explore the cause of difference between the predicted volume fractions of{10ˉ12}ET and the correspondingly measured ones,eight representative grains per deformed sample are selected from Fig.5 and they are then thoroughly analyzed by using IPF maps and(0002)pole figures,as shown in Fig.12.In the present study,the selected eight grains per deformed sample could be further divided into two groups:(i)four grains with theirc-axis inclined about 20°–60° towards ND and(ii)four grains with theirc-axis tilted about 60°–90° towards ND.

    Fig.9.Statistical analysis of SF values on basalslip,prismaticslip and pyramidalslip during uniaxial tension:(a)UT-0° sample;(b)UT-30° sample,(c)UT-45° sample;(d)UT-60° sample,(e)UT-90° sample.

    Fig.10.Predicted(0002)pole figures based on the activities of{10ˉ12}ET within deformed samples during uniaxial tension:(a)At deformation degree of 6%;(b)At deformation degree of 12%;(c)At deformation degree of 21%.

    Fig.11.Predicted(0002)pole figures based on the activities of deformation mechanisms other than{10ˉ12}ET within deformed samples during uniaxial tension:(a)At deformation degree of 6%;(b)At deformation degree of 12%;(c)At deformation degree of 21%.

    Fig.12.IPF maps and(0002)pole figures of selected eight grains per deformed sample at deformation degree of 6%:(a)UT-0° sample;(b)UT-30° sample,(c)UT-45° sample;(d)UT-60° sample,(e)UT-90° sample.

    As for grains with theirc-axis inclined about 20°–60° towards ND,IPF maps demonstrate that only one or two twin variants occur during plastic deformation and they mainly rotate their initial orientations to the region near TD.In terms of grains with theirc-axis tilted about 60°–90° towards ND,the number of activated twin variants is gradually decreasing along with the increasing tilted angle between loading direction and RD of sheet.For example,there exist up to four twin variants within UT-0° sample,while only one twin variant emerges within UT-90° sample.Moreover,the corresponding(0002)pole figures depict that these twin variants mainly rotate their initial orientations to the area close to RD.Guo et al.[9]have claimed that as for{10ˉ12}ET during plastic deformation,the role of sustaining plastic strain means the activation of more twin variants,whereas the role of accommodating plastic strain between individual grains indicates the activation of less twin variants.Consequently,we have reason to believe that compare to the role of accommodating plastic strain,{10ˉ12}ETs in UT-0° sample and UT-30° sample prefer to sustain plastic strain.Meanwhile,{10ˉ12}ETs within UT-90° sample are inclined to accommodate plastic strain between individual grains.Based on the aforementioned analysis,the reason leading to the overestimation of predicted volume fractions of{10ˉ12}ET in UT-0° sample and UT-30° sample,as shown in Fig.7,can be disclosed.Because many twin variants tend to activate within a grain,twin-twin interactions occur more frequently,and thus hinder the twin growth[37].However,this“barrier effect”is not included in the VPSC modeling procedure at the present form,where all self-hardening coefficients and latent-hardening coefficients are set to unity.One potential access to tackle this issue is that this“barrier effect”would be considered indirectly by modifying the self-hardening coefficient of{10ˉ12}ET.With respect to the rest samples,although the aforementioned“barrier effect”is relatively weak and can be neglected in the VPSC modeling because there are much less interactions between twin variants,activation of{10ˉ12}ET is mainly ascribed to be the compatible deformation between individual grains.Unfortunately,this aspect has not been appropriately considered in the present form of VPSC code,and finally results in the underestimation of predicted volume fractions of{10ˉ12}ET in UT-45° sample,UT-60° sample and UT-90°sample,as shown Fig.7[17].

    5.Conclusions

    Through the combination of experimental investigation and numerical simulation,the relationship between the activities of involved deformation mechanisms and evolution of microstructure and texture during uniaxial tension of AZ31 magnesium alloy with a rare non-basal texture has been thoroughly investigated in the present study.The following conclusions can be obtained.

    (1)Except for basalslip and prismaticslip,{10ˉ12}ET deeply participates in the plastic deformation.With the increasing tilted angle between loading direction and RD of sheet,the activity of{10ˉ12}ET reduces gradually and its role in plastic deformation changes from the one mainly sustaining plastic strain to the one mainly accommodating local strain between individual grains.

    (2)The formation of TD-component texture during uniaxial tension is mainly ascribe to the activities of{10ˉ12}ET.For UT-0°sample and UT-30°sample,the concentration of tilted basal poles towards ND is observable at early stage of plastic deformation.This aspect is mainly attributed to the activities of{10ˉ12}ET.At large plastic deformation,the competition between basalslip and pyramidalslip is responsible for the concentration of tilted basal poles towards ND within all deformed samples.The larger difference is between the activities of basalslip and pyramidalslip,the smaller separation is between these two tilted basal poles.

    (3)Because of taking no account of interaction between twin variants in the VPSC modeling,the predicted volume fractions of{10ˉ12}ET in UT-0° sample and UT-30° sample are larger than the correspondingly measured ones.In addition,as compatible deformation between individual grains can not be modeled in the VPSC modeling,the predicted volume fractions of{10ˉ12}ET in the remaining samples are smaller than the correspondingly measured ones.

    Declaration of Competing Interest

    None.

    Acknowledgments

    This work was supported by the National Natural Science Foundation of China(Grant Nos.51805064,51701034,51822509),the Scientific and Technological Research Program of Chongqing Municipal Education Commission(Grant Nos.KJQN201801137),the Basic and Advanced Research Project of CQ CSTC(Grant Nos.cstc2017jcyjAX0062,cstc2018jcyjAX0035).

    国精品久久久久久国模美| 亚洲熟女精品中文字幕| 91久久精品国产一区二区三区| 欧美日韩视频高清一区二区三区二| 国产精品久久久久久精品电影小说| 欧美成人精品欧美一级黄| 中文字幕制服av| 黑人巨大精品欧美一区二区蜜桃 | 精品人妻偷拍中文字幕| 这个男人来自地球电影免费观看 | 大香蕉久久网| 纵有疾风起免费观看全集完整版| 国内揄拍国产精品人妻在线| 免费av中文字幕在线| 婷婷色综合www| 国产精品国产三级国产专区5o| 久久精品国产亚洲av天美| 80岁老熟妇乱子伦牲交| 性高湖久久久久久久久免费观看| 久久久久久久久久久久大奶| 日韩伦理黄色片| 国产精品人妻久久久影院| 国产精品一区二区在线不卡| 午夜福利网站1000一区二区三区| 亚洲精品亚洲一区二区| 亚洲国产欧美在线一区| av卡一久久| 国产精品熟女久久久久浪| 99热全是精品| 日本91视频免费播放| 麻豆成人av视频| 交换朋友夫妻互换小说| 欧美bdsm另类| 精品久久久久久久久av| 美女福利国产在线| 国产精品国产三级国产专区5o| 欧美 日韩 精品 国产| 国产av一区二区精品久久| 夫妻性生交免费视频一级片| 国产av码专区亚洲av| 午夜日本视频在线| 女人精品久久久久毛片| 国产伦精品一区二区三区视频9| 久久久久久伊人网av| 我要看日韩黄色一级片| 毛片一级片免费看久久久久| 人妻人人澡人人爽人人| 最后的刺客免费高清国语| 婷婷色综合www| 国产中年淑女户外野战色| 久久久a久久爽久久v久久| 久久久欧美国产精品| 亚洲久久久国产精品| 亚洲av日韩在线播放| 亚洲欧美精品专区久久| 婷婷色综合大香蕉| 男女国产视频网站| 大片免费播放器 马上看| 国语对白做爰xxxⅹ性视频网站| 能在线免费看毛片的网站| 青春草国产在线视频| 午夜精品国产一区二区电影| 国产高清三级在线| 国产成人精品福利久久| 国产精品一区二区性色av| 久久女婷五月综合色啪小说| 少妇高潮的动态图| 黄色一级大片看看| 欧美日韩综合久久久久久| 男女啪啪激烈高潮av片| 爱豆传媒免费全集在线观看| 国产av国产精品国产| 久久精品久久久久久久性| 久久这里有精品视频免费| 黄色日韩在线| 免费观看a级毛片全部| 日韩中文字幕视频在线看片| 人人妻人人添人人爽欧美一区卜| 日韩大片免费观看网站| 欧美国产精品一级二级三级 | 男人和女人高潮做爰伦理| 成人二区视频| 国产伦精品一区二区三区四那| av天堂中文字幕网| 日韩av在线免费看完整版不卡| 国产精品成人在线| 一本—道久久a久久精品蜜桃钙片| 偷拍熟女少妇极品色| 婷婷色综合www| 亚洲国产欧美日韩在线播放 | 中文精品一卡2卡3卡4更新| av国产精品久久久久影院| 国产美女午夜福利| av黄色大香蕉| 国产av一区二区精品久久| 99精国产麻豆久久婷婷| 亚洲精品久久久久久婷婷小说| 一区二区三区乱码不卡18| 伊人久久国产一区二区| 亚洲激情五月婷婷啪啪| 卡戴珊不雅视频在线播放| 高清在线视频一区二区三区| 日韩av在线免费看完整版不卡| 美女xxoo啪啪120秒动态图| 国产精品久久久久久久久免| 日本-黄色视频高清免费观看| 国产精品免费大片| 国产精品久久久久久精品古装| 五月开心婷婷网| 久久久久久伊人网av| 男人和女人高潮做爰伦理| 午夜视频国产福利| 一区二区av电影网| 高清欧美精品videossex| 久久久国产欧美日韩av| 蜜臀久久99精品久久宅男| 国产黄片视频在线免费观看| 中文字幕人妻熟人妻熟丝袜美| 我的老师免费观看完整版| 国产亚洲最大av| 亚洲精品456在线播放app| 亚洲成色77777| 日韩三级伦理在线观看| 国产无遮挡羞羞视频在线观看| 性高湖久久久久久久久免费观看| 国产精品三级大全| 欧美成人午夜免费资源| 亚洲激情五月婷婷啪啪| 美女内射精品一级片tv| 免费看不卡的av| 亚洲天堂av无毛| 好男人视频免费观看在线| 夜夜爽夜夜爽视频| 日本午夜av视频| 精品卡一卡二卡四卡免费| 免费少妇av软件| 亚洲av国产av综合av卡| 最后的刺客免费高清国语| 久久婷婷青草| 精品国产一区二区久久| 日韩 亚洲 欧美在线| 内射极品少妇av片p| 菩萨蛮人人尽说江南好唐韦庄| 日本欧美国产在线视频| 不卡视频在线观看欧美| 最近最新中文字幕免费大全7| 国产美女午夜福利| 国产高清不卡午夜福利| 免费av中文字幕在线| 亚洲成人一二三区av| 久久久久久久久久人人人人人人| 丰满迷人的少妇在线观看| 内地一区二区视频在线| 婷婷色麻豆天堂久久| 日日摸夜夜添夜夜爱| 一级爰片在线观看| 国产精品福利在线免费观看| 免费观看的影片在线观看| 午夜视频国产福利| 最黄视频免费看| av不卡在线播放| 国产成人午夜福利电影在线观看| 久久久久久久久大av| 最近2019中文字幕mv第一页| 国产男女超爽视频在线观看| 9色porny在线观看| 国产免费又黄又爽又色| 亚洲精品,欧美精品| 亚洲婷婷狠狠爱综合网| 日日摸夜夜添夜夜添av毛片| 久久久久视频综合| 亚洲av综合色区一区| 在线天堂最新版资源| 亚洲欧洲精品一区二区精品久久久 | 国产精品久久久久久av不卡| 男女无遮挡免费网站观看| 中文欧美无线码| 精品久久久精品久久久| 不卡视频在线观看欧美| 国产精品三级大全| 伊人久久国产一区二区| 国产一区二区三区av在线| 亚洲综合精品二区| 日本黄色日本黄色录像| 多毛熟女@视频| 国产欧美日韩一区二区三区在线 | 久久久国产一区二区| 色视频www国产| 国产精品久久久久久久电影| 久久97久久精品| 精品一区二区三卡| 精品国产一区二区久久| 啦啦啦啦在线视频资源| 男的添女的下面高潮视频| 人人妻人人添人人爽欧美一区卜| 午夜免费观看性视频| av福利片在线| 人妻系列 视频| 久久久久久久久久人人人人人人| 色视频在线一区二区三区| 精品亚洲成a人片在线观看| 这个男人来自地球电影免费观看 | 国产乱人偷精品视频| 男人舔奶头视频| av国产久精品久网站免费入址| 成人午夜精彩视频在线观看| 日韩三级伦理在线观看| 91精品国产九色| 久久人妻熟女aⅴ| 亚洲情色 制服丝袜| 国产高清三级在线| 搡女人真爽免费视频火全软件| 女性被躁到高潮视频| 亚洲三级黄色毛片| 久久精品国产亚洲av涩爱| 日韩视频在线欧美| h日本视频在线播放| 国产永久视频网站| 日本猛色少妇xxxxx猛交久久| av女优亚洲男人天堂| 99热这里只有精品一区| 在线天堂最新版资源| 欧美精品国产亚洲| 精品人妻熟女av久视频| 美女中出高潮动态图| av.在线天堂| 亚州av有码| 五月天丁香电影| 亚洲三级黄色毛片| 国产有黄有色有爽视频| 国产精品国产三级国产av玫瑰| 99久久精品国产国产毛片| 亚洲第一av免费看| 夜夜看夜夜爽夜夜摸| 日韩三级伦理在线观看| 五月天丁香电影| 精品一品国产午夜福利视频| 男女边摸边吃奶| 欧美另类一区| 免费看日本二区| 国产在线免费精品| 国产亚洲一区二区精品| 91成人精品电影| 亚洲精品aⅴ在线观看| 午夜久久久在线观看| 一级黄片播放器| 国产毛片在线视频| 少妇的逼好多水| 久久精品国产a三级三级三级| 国产极品天堂在线| 日本欧美国产在线视频| 欧美区成人在线视频| 观看美女的网站| 三上悠亚av全集在线观看 | 日本午夜av视频| 免费不卡的大黄色大毛片视频在线观看| 一级毛片我不卡| 人人妻人人看人人澡| 日韩伦理黄色片| 欧美 亚洲 国产 日韩一| 国产精品国产av在线观看| 久久久久精品久久久久真实原创| 一本一本综合久久| 成年女人在线观看亚洲视频| 一区二区三区精品91| 国产精品女同一区二区软件| 中文字幕亚洲精品专区| 日韩熟女老妇一区二区性免费视频| 日本wwww免费看| 女性被躁到高潮视频| 亚洲三级黄色毛片| 亚洲天堂av无毛| 国产高清有码在线观看视频| 日本黄色片子视频| 国产成人freesex在线| 精品久久久久久电影网| 中文字幕精品免费在线观看视频 | 久久97久久精品| 新久久久久国产一级毛片| 国产成人精品无人区| 亚洲av电影在线观看一区二区三区| 极品教师在线视频| 精品国产一区二区三区久久久樱花| 国产男人的电影天堂91| 日韩一区二区三区影片| 性高湖久久久久久久久免费观看| 国产精品国产三级国产av玫瑰| 水蜜桃什么品种好| 十八禁网站网址无遮挡 | 中文字幕人妻熟人妻熟丝袜美| 交换朋友夫妻互换小说| 91在线精品国自产拍蜜月| 国产日韩欧美亚洲二区| 精品少妇黑人巨大在线播放| 视频区图区小说| 亚洲婷婷狠狠爱综合网| 美女中出高潮动态图| 日韩av在线免费看完整版不卡| 91久久精品国产一区二区三区| 国产伦精品一区二区三区视频9| 在线观看www视频免费| 亚洲av欧美aⅴ国产| 高清欧美精品videossex| 久久女婷五月综合色啪小说| 免费观看无遮挡的男女| 五月开心婷婷网| 午夜免费鲁丝| 亚洲在久久综合| av天堂久久9| 精品一品国产午夜福利视频| av播播在线观看一区| 日本欧美国产在线视频| av专区在线播放| 91午夜精品亚洲一区二区三区| 久久久久久久精品精品| 韩国av在线不卡| 日本黄大片高清| 91精品伊人久久大香线蕉| a级片在线免费高清观看视频| 99久久中文字幕三级久久日本| 亚洲精品成人av观看孕妇| 夫妻性生交免费视频一级片| 26uuu在线亚洲综合色| 夜夜骑夜夜射夜夜干| 久久久久久久久久成人| 亚洲国产精品专区欧美| 精品一区二区三区视频在线| 免费大片黄手机在线观看| 自拍欧美九色日韩亚洲蝌蚪91 | 黄色配什么色好看| 欧美国产精品一级二级三级 | 亚洲av.av天堂| 性色av一级| 日韩熟女老妇一区二区性免费视频| 3wmmmm亚洲av在线观看| 久久99热这里只频精品6学生| 免费看日本二区| 九草在线视频观看| 亚洲欧洲日产国产| 亚洲av综合色区一区| 亚洲经典国产精华液单| 丰满乱子伦码专区| 中文在线观看免费www的网站| 国产亚洲5aaaaa淫片| 久久国内精品自在自线图片| 欧美变态另类bdsm刘玥| 亚洲精品乱久久久久久| 美女视频免费永久观看网站| 日韩人妻高清精品专区| 亚洲欧美清纯卡通| 久久鲁丝午夜福利片| 成人漫画全彩无遮挡| 99久久人妻综合| 国产午夜精品久久久久久一区二区三区| 中文字幕精品免费在线观看视频 | 国产精品99久久99久久久不卡 | 亚洲欧洲精品一区二区精品久久久 | 秋霞伦理黄片| 日韩中字成人| 久久精品国产亚洲网站| 日本-黄色视频高清免费观看| 免费观看性生交大片5| 国产成人精品一,二区| 国产极品粉嫩免费观看在线 | 国产免费视频播放在线视频| 乱码一卡2卡4卡精品| 美女主播在线视频| 啦啦啦啦在线视频资源| 成人毛片a级毛片在线播放| av卡一久久| 91精品一卡2卡3卡4卡| 亚洲综合色惰| 免费黄色在线免费观看| 色94色欧美一区二区| 日韩强制内射视频| 欧美日韩亚洲高清精品| 亚洲精品亚洲一区二区| 好男人视频免费观看在线| 久久鲁丝午夜福利片| 国产日韩一区二区三区精品不卡 | 亚洲人成网站在线播| av播播在线观看一区| 国产精品嫩草影院av在线观看| 看免费成人av毛片| 精品一区在线观看国产| 观看免费一级毛片| 美女主播在线视频| 久久人人爽人人片av| 国产免费一级a男人的天堂| 婷婷色综合www| 伦理电影大哥的女人| 天美传媒精品一区二区| 日日摸夜夜添夜夜添av毛片| 午夜激情久久久久久久| 亚洲美女搞黄在线观看| 91aial.com中文字幕在线观看| 国产老妇伦熟女老妇高清| 国产在线视频一区二区| 国国产精品蜜臀av免费| 亚洲人成网站在线播| freevideosex欧美| 精品少妇内射三级| 亚洲精华国产精华液的使用体验| 我的女老师完整版在线观看| 久热久热在线精品观看| 男女啪啪激烈高潮av片| 热99国产精品久久久久久7| av在线老鸭窝| 五月伊人婷婷丁香| 丰满饥渴人妻一区二区三| 制服丝袜香蕉在线| 日本wwww免费看| 亚洲精品国产av蜜桃| 成人午夜精彩视频在线观看| 成人国产麻豆网| 国产精品久久久久久精品古装| a级毛片在线看网站| 国模一区二区三区四区视频| 国产欧美亚洲国产| 青青草视频在线视频观看| av视频免费观看在线观看| 免费播放大片免费观看视频在线观看| 免费在线观看成人毛片| 国产免费福利视频在线观看| 午夜福利视频精品| 80岁老熟妇乱子伦牲交| 欧美精品国产亚洲| 少妇精品久久久久久久| 中国三级夫妇交换| 内地一区二区视频在线| 亚洲av中文av极速乱| videossex国产| 国产成人freesex在线| 午夜激情久久久久久久| 久久久久久久亚洲中文字幕| 男人舔奶头视频| 国产片特级美女逼逼视频| 夜夜看夜夜爽夜夜摸| 免费观看无遮挡的男女| 欧美老熟妇乱子伦牲交| 又粗又硬又长又爽又黄的视频| 九九爱精品视频在线观看| 亚洲美女黄色视频免费看| 91精品伊人久久大香线蕉| 欧美激情国产日韩精品一区| 亚洲欧洲国产日韩| 青春草国产在线视频| 大陆偷拍与自拍| 一级二级三级毛片免费看| 久久久国产欧美日韩av| 日韩伦理黄色片| 日韩亚洲欧美综合| 99精国产麻豆久久婷婷| 天美传媒精品一区二区| 精品视频人人做人人爽| 如日韩欧美国产精品一区二区三区 | 男女免费视频国产| 春色校园在线视频观看| 美女脱内裤让男人舔精品视频| 好男人视频免费观看在线| 成人亚洲欧美一区二区av| 亚洲国产最新在线播放| 极品少妇高潮喷水抽搐| 只有这里有精品99| 日韩 亚洲 欧美在线| 欧美区成人在线视频| 嫩草影院入口| 国产高清不卡午夜福利| 成人无遮挡网站| kizo精华| 多毛熟女@视频| 久久久精品免费免费高清| 丰满人妻一区二区三区视频av| 黑人巨大精品欧美一区二区蜜桃 | 亚洲丝袜综合中文字幕| 精品一区二区免费观看| 91成人精品电影| 日日撸夜夜添| 亚洲国产精品国产精品| 亚洲伊人久久精品综合| 亚洲精品国产av蜜桃| 日本色播在线视频| 在线观看www视频免费| 欧美精品一区二区免费开放| 国产日韩欧美亚洲二区| 日韩强制内射视频| 人人妻人人澡人人爽人人夜夜| 久久久久网色| av免费观看日本| 国产高清三级在线| 亚洲情色 制服丝袜| 久久久久久久久久人人人人人人| 最近2019中文字幕mv第一页| 久久久久精品久久久久真实原创| 国产淫语在线视频| 啦啦啦中文免费视频观看日本| 肉色欧美久久久久久久蜜桃| 韩国高清视频一区二区三区| 七月丁香在线播放| 久久亚洲国产成人精品v| 精品卡一卡二卡四卡免费| 美女大奶头黄色视频| 晚上一个人看的免费电影| 亚洲精品色激情综合| 中国美白少妇内射xxxbb| 久久午夜福利片| 男女啪啪激烈高潮av片| 高清毛片免费看| 国产亚洲午夜精品一区二区久久| 免费大片黄手机在线观看| 亚洲四区av| 欧美精品一区二区免费开放| av在线老鸭窝| 色视频在线一区二区三区| av.在线天堂| 丰满饥渴人妻一区二区三| 亚洲av.av天堂| 欧美高清成人免费视频www| 中文字幕人妻丝袜制服| 丰满少妇做爰视频| 九九在线视频观看精品| 一区二区三区乱码不卡18| 中文字幕人妻丝袜制服| 在线 av 中文字幕| 伊人亚洲综合成人网| 在线免费观看不下载黄p国产| 亚洲精品,欧美精品| 在线观看www视频免费| 亚洲美女黄色视频免费看| 久久久久久久大尺度免费视频| 日韩精品有码人妻一区| 久久久久久久久久久丰满| 成人特级av手机在线观看| 人人妻人人澡人人爽人人夜夜| 狂野欧美白嫩少妇大欣赏| 国产伦精品一区二区三区视频9| 午夜视频国产福利| videossex国产| 亚洲精品久久久久久婷婷小说| 国产乱人偷精品视频| 搡老乐熟女国产| 国产av码专区亚洲av| 国产亚洲一区二区精品| 日韩三级伦理在线观看| 免费看光身美女| 国产淫片久久久久久久久| 26uuu在线亚洲综合色| 午夜免费观看性视频| 在线观看免费高清a一片| 日韩av不卡免费在线播放| 久久精品国产鲁丝片午夜精品| av天堂久久9| 熟女电影av网| 亚洲精品中文字幕在线视频 | 欧美成人精品欧美一级黄| 高清av免费在线| 成人免费观看视频高清| 午夜激情福利司机影院| 十分钟在线观看高清视频www | 成人特级av手机在线观看| 国产男女超爽视频在线观看| 韩国高清视频一区二区三区| 大码成人一级视频| 少妇高潮的动态图| 日韩欧美精品免费久久| 亚洲欧美一区二区三区黑人 | 亚洲国产精品专区欧美| 久久久久久久久久久丰满| 中文精品一卡2卡3卡4更新| 91精品一卡2卡3卡4卡| 亚洲,一卡二卡三卡| 夫妻性生交免费视频一级片| 亚洲国产最新在线播放| 亚洲欧美精品自产自拍| 国产美女午夜福利| 国产精品成人在线| 99热这里只有精品一区| 亚洲av男天堂| 国产一区有黄有色的免费视频| 在线观看三级黄色| a级一级毛片免费在线观看| 18禁在线播放成人免费| 国产精品.久久久| 欧美 亚洲 国产 日韩一| 天天躁夜夜躁狠狠久久av| 一级黄片播放器| 看非洲黑人一级黄片| 涩涩av久久男人的天堂| 高清av免费在线| 国产毛片在线视频| 嫩草影院入口| 国产女主播在线喷水免费视频网站| 人妻系列 视频| 亚洲欧洲国产日韩| 国产色爽女视频免费观看| 97在线视频观看| 伊人久久精品亚洲午夜| 插阴视频在线观看视频| 天天躁夜夜躁狠狠久久av| 嘟嘟电影网在线观看| 亚洲av男天堂| 国产午夜精品一二区理论片| av国产精品久久久久影院| 欧美日韩综合久久久久久| 精品一区二区三区视频在线| 成年人免费黄色播放视频 | 日韩av免费高清视频| 亚洲精品一二三| 啦啦啦中文免费视频观看日本| 欧美区成人在线视频| 水蜜桃什么品种好| 一区在线观看完整版| 精品亚洲成a人片在线观看| 丰满乱子伦码专区| av有码第一页|