• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Review of 4Pi Fluorescence Nanoscopy

    2022-06-11 09:03:00XingHoYimingLiShungFuYnghuiLiYingkeXuCuifngKungXuLiu
    Engineering 2022年4期

    Xing Ho*, Yiming Li, Shung Fu, Ynghui Li, Yingke Xu, Cuifng Kung Xu Liu

    a State Key Laboratory of Modern Optical Instrumentation, College of Optical Science and Technology, Zhejiang University, Hangzhou 310027, China

    b Department of Biomedical Engineering, Southern University of Science and Technology, Shenzhen 518055, China

    c College of Optical and Electronic Technology, China Jiliang University, Hangzhou 310018, China

    d Key Laboratory for Biomedical Engineering of Ministry of Education & Zhejiang Provincial Key Laboratory of Cardio-Cerebral Vascular Detection Technology and Medicinal Effectiveness Appraisal, College of Biomedical Engineering and Instrument Science, Zhejiang University, Hangzhou 310027, China

    Keywords:Fluorescence nanoscopy Super-resolution imaging 4Pi nanoscopy IsoSTED 4Pi-SMLM

    ABSTRACT Since the 1990s, continuous technical and scientific advances have defied the diffraction limit in microscopy and enabled three-dimensional(3D)super-resolution imaging.An important milestone in this pursuit is the coherent utilization of two opposing objectives(4Pi geometry)and its combination with superresolution microscopy. Herein, we review the recent progress in 4Pi nanoscopy, which provides a 3D,non-invasive,diffraction-unlimited,and isotropic resolution in transparent samples.This review includes both the targeted and stochastic switching modalities of 4Pi nanoscopy.The schematics,principles,applications, and future potential of 4Pi nanoscopy are discussed in detail.

    1. Introduction

    Since the discovery of the diffraction limit by Abbe et al.in 1873[1], the resolution of far-field optical microscopy has been constrained by the diffraction of light for over a century. However,the pursuit of higher resolution has been in progress[2],and major breakthroughs have been achieved since the early 1990s [3].Diffraction limits the resolution of visible light microscopy in resolving objects no closer than 250 nm; however, nanoscopy has overcome this fundamental limit and improved the achievable resolution by up to a factor of ten in the xy-plane and a factor of six along the z-axis. The development of far-field fluorescence nanoscopy has progressed significantly in the past two decades. Notably, fluorescence nanoscopy does not refer to a specific technique. Instead, scientists use this term to describe several different modalities as the common underlying basis is the switching effect on fluorescence emission. All fluorescence nanoscopy concepts realized hitherto involve the bright (‘‘on”) and dark (‘‘off”)states of fluorophores to record subdiffraction-limited features sequentially in time [4,5], and the molecular probability of being either in the bright or in dark state depends nonlinearly on the light intensity applied [4]. By either the coordinate-targeted or stochastic temporal switching of fluorophores, these techniques remarkably visualize cellular structures specifically labeled with fluorophores at the subdiffraction-limited scale and thus have enabled the investigation of many fundamental biological phenomena with light microscopy for the first time [6].

    As most biological structures are arranged three-dimensionally,extending super-resolution imaging to three dimensions is desirable to unambiguously visualize these structures and/or their motions.Hence, several innovative approaches have been developed in this regard. For single-molecule localization microscopy (SMLM) techniques,such as photoactivated localization microscopy(PALM)[7],stochastic optical reconstruction microscopy [8], and fluorescence PALM[9],methods for extending imaging from two to three dimensions primarily include the simultaneous imaging of two different focal planes [10] or point-spread function (PSF) engineering [11–14].For coordinate-targeted nanoscopy techniques,such as stimulated emission depletion(STED)microscopy[15]and reversible saturable optical fluorescence transition (RESOLFT) microscopy [16],the most commonly used strategy is to employ two-phase masks simultaneously to create a three-dimensional (3D) intensity minimum in the center of the STED/RESOLFT focus[17,18].

    For both techniques,the resolution can be unlimited.However,diffraction is still critical in these ‘‘diffraction-unlimited”approaches because their resolution benefits significantly from the sharp focusing of light. If light can be focused/collected from only one side of the focal plane, then the diffractive nature of the light stretches the PSF more along the propagation direction of the beam. Consequently, it is more challenging to enhance the resolution in the axial direction when using single-objective microscopes. In practice, the lateral resolution of a nanoscope can be between 20 and 40 nm in the focal plane, whereas the axial resolution is always ~2.5 times greater.

    A 3D isotropic resolution is preferred because it offers more natural vision and yields a more precise image-based data analysis.However, as a conventional lens can collect only hemispherical wavefronts,it is extremely difficult to achieve isotropic 3D resolution using a single-objective system without sacrificing the lateral resolution. If an imaging system can collect the other half of the wavefront on the ‘‘back side” of the focal plane, producing a(nearly) complete spherical wavefront, then the PSF will be(almost)spherical owing to the restored symmetry. Consequently,isotropic 3D resolution can be achieved. Based on this idea, in the early 1990s, Hell et al. [19,20] introduced a 4Pi microscope equipped with two opposing objectives. One objective can only encompass a maximum semi-aperture angle of approximately 65°, whereas two opposing objectives virtually mimic an aperture with a nearly full solid angle of 4π (2.5π–3π in practice). In 4Pi microscopy, the counter-propagating wavefronts of the illumination from opposing objectives form interference fringes at the common focal spot (4Pi type A), as shown in Fig. 1. Alternatively, the collected fluorescence may interfere at the detector (4Pi type B).This additional interference around the focal region, which is the essence of scanning 4Pi microscopy, significantly sharpens the PSF along the optical axis. If only excitation (4Pi type A) or emission (4Pi type B) photons are coherent, then this approach can improve the resolution by three to four folds. Sharpening both the excitation and emission PSFs (4Pi type C) further improves the axial resolution up to approximately seven folds [21]. In addition, the 4Pi arrangement can facilitate the doubling of the detected fluorescence, thereby improving the signal-to-noise ratio(SNR)of the image.Similarly,incoherent interference illumination image interference microscopy[22] applies an axial-structured light field to illuminate the sample and coherently collects fluorescence photons through both objectives,thereby attaining a resolution comparable to that of spot-scanning 4Pi microscopy in a widefield, camera-based imaging architecture.

    When combined with fluorescence nanoscopy methods, 4Pi microscopy can acquire images with further improved resolution in three dimensions,particularly in the z-direction.Similar to conventional nanoscopes with one objective, 4Pi nanoscopes can be classified as targeted switching (isoSTED [23]/4Pi-RESOLFT [24])or stochastic switching(interferometric photoactivated localization microscopy(iPALM)[25]/4Pi-single molecule switching microscopy(SMS) [26]/4Pi-SMLM [27]) modalities, as shown in Fig. 2(a) [23–27].In the case of the targeted switching modality,the destructive interference of counter-propagated wavefronts allows a much sharper central minimum to be created in the axial direction of the STED/RESOLFT focus (Fig. 2(b) [25–27]); subsequently, the fluorescence emission is confined to the immediate vicinity of the focal spot.The major technical difference that distinguishes 4Pi-RESOLFT from isoSTED is that the former typically uses reversibly switchable fluorescent proteins (RSFPs) to provide mandatory bright and dark states. In the case of the stochastic switching modality, enhanced resolution is realized by converting the phase information hidden in the interference fringes to precise z localization (Fig. 2(b)).Depending on the design of the interference cavity, both three(iPALM [25]) and four (4Pi-SMS [26], 4Pi-SMLM [27]) interference phase images can be recorded simultaneously.

    In the following sections, we discuss both the concepts of 4Pi nanoscopy and their applications in detail. By contrast, imageinterference and incoherent-illumination-interference structured illumination microscopy (I5S) [28] is beyond the scope of this review. I5S expands the application of structured illumination in the lateral direction, compressing the effective PSF both laterally and axially. However, it does not rely on any switching fluorescence effects, either targeted switching or stochastic illumination.This is advantageous because it makes I5S compatible with almost all types of fluorophores.However,theoretically,I5S can only double the resolution when using wide-field microscopes as a reference. To further improve the resolution, nonlinear effects such as fluorescence saturation[29–31]are still necessary.However,saturated I5S (denoted as ‘‘I5SS”) is yet to be realized.

    2. Targeted switching of 4Pi nanoscopy

    Fig.1. Simplified schematic and principle of 4Pi microscopy.(a)Simplified schematic of 4Pi microscopy.(b)PSFs in 4Pi nanoscopy in axial(xz)plane.Coherent superposition of PSFs from the upper and lower objectives sharpens focal spot size in z-axis. (c) Effective PSFs of different 4Pi types. From left to right: 4Pi type A, excitation beams are coherent;4Pi type B,emission beams(fluorescence)are coherent;4Pi type C,both are coherent. APD:avalanche photodiode;BS: 50/50 beam splitter;DM:dichroic mirror;L: lens; M: mirror; SM: scanning mirror.

    STED nanoscopy is based on a scheme developed in 1994[15]and was first demonstrated in material science in 1999[32]and subsequently in biology in 2000[33]; since then, it has revolutionized fluorescence imaging.It is the first developed nanoscopy technique operating in the targeted switching mode; it restricts fluorescence to a subdiffraction-sized region at known positions by depleting excited fluorophores surrounding it through stimulated emissions.A peak-centered excitation focal spot,nested by a ring-shaped depletion focus,is scanned across the sample,and the image is generated by reading out signals from a point detector conjugated to the focus. To improve the resolution of the STED method, fluorescence emission must be inhibited everywhere except at the center of the depletion focus;therefore,a high quality‘‘zero”-intensity point in the center of the ring-shaped depletion pattern is mandatory[34].

    Fig.2. Simplified schematic and principle of 4Pi nanoscopy.(a)Simplified schematic of isoSTED/4Pi-RESOLFT(left)and 4Pi-SMLM nanoscopes(right).For both modalities,the sample is mounted between two opposing objectives.The polarization states at indicated points(I–XI in circles)are displayed around the beam path.Specifically,in VII,VIII,and XI,dashed arrows represent an additional π/2 phase(introduced by quartz wedges)delay with respect to the solid arrows along the same direction.Left:In an isoSTED/4Pi-RESOLFT nanoscope,the beams for STEDxy(lateral)and STEDz(axial)are combined by a polarizing beam splitter(PBS)and then fed through a scanning mirror unit into a 4Pi cavity.STEDxy and STEDz beams are incoherent and orthogonal in the polarization direction.Incoming beams are further split by the second PBS and generate STEDxy and STEDz depletion patterns(the first and the second panels from left in(b),respectively)at the common focus of the opposing objectives.These two patterns feature the same focal zero in terms of intensity. Their superimposition enables isotropic fluorescence compression by stimulated emission (the third panel from left in (b)), for which the fluorophores underneath the STED patterns are forced to reside in the dark(‘‘off”)state.The fluorescence from the immediate vicinity of the focus is inversely collected by the same objectives,reflected by a dichroic mirror,and finally collected by the detector(s).Right:In a 4Pi-SMLM nanoscope,the fluorescence is split and recombined by a set of beam splitters to create partial wavefronts with different interference phases. The interference wavefronts are then simultaneously detected by the cameras after the interference cavity. Whereas the exact beam path and number of detectors may vary in different designs[25–27],the principle for molecule localization is identical: As the fringe-like interference 4Pi-PSF contains more high-frequency information,the resulting localization precision of 4Pi-PSF is higher than that of single-objective PSF.(b)PSFs in 4Pi nanoscopy in axial(xz)plane.From left to right:STEDxy,STEDz,combined STED(red)and effective(green)PSFs in isoSTED/4Pi-RESOLFT nanoscopy;fluorescence PSFs with φ=0,90°,270°,and 180°in 4Pi-SMLM nanoscopy.For a clear depiction of the effective PSF in isoSTED/4Pi-RESOLFT nanoscopy and fluorescence PSFs in 4Pi-SMS nanoscopy,the detected images on the detectors(APD or cameras)in the focal(xy)plane are presented on the top-right corners of the corresponding PSFs.GW:glass window;HWP:half wave plate; Q: quartz wedge; VP: 0–2π vortex phase plate; s/p: s-/p-polarization.

    Technical advances in the past 15 years have enabled a new era of 3D imaging in STED nanoscopy. In particular, using two opposing objectives in a 4Pi geometry allows a sharp central minimum to be created in the axial direction of the depletion focus. It has enabled a 33 nm z-resolution[35] despite the insufficient resolution improvement in ‘‘STED-4Pi microscopy”[35,36] in the focal plane. An improved version of this method, isoSTED nanoscopy[23], has demonstrated 3D isotropic resolution (Fig. 2(a)). To isotropically compress fluorescence, isoSTED nanoscopy utilizes two depletion patterns featuring a common focal zero:one for lateral (STEDxy) and another for axial depletion (STEDz), as shown in Fig. 2(b). Adjusting the power allocation between these two patterns enables a precise control of the PSF size and hence the resolution. Specifically, the formation of the STEDzdepletion profile relies on the superposition of the waves emerging from the two objectives propagating in opposite directions. Owing to the highly symmetric intensity and phase distribution of the single-objective PSF with respect to the focal plane, in addition to the central‘‘zero”-intensity point, the destructive interference of the waves yields axially repetitive minima above and below the focal plane in the STEDzprofile,overlapping with the excitation and detection PSFs. These minima,which theoretically correspond to zero intensity, prevent fluorescence depletion at their locations, resulting in side-lobes in the effective PSF. These side-lobes create artifacts,that is,‘‘ghost images,”which deteriorate the image quality significantly.Furthermore,when the sample is scanned in the axial direction, the positions of the maxima shift under the PSF envelope;thus, any deconvolution procedure based on a spatially invariant PSF is rendered futile. In principle, deconvolution with a variable PSF[37] can mitigate this phenomenon; however, the method relies on accurate knowledge regarding the PSF and is only applicable to images with good SNRs. To eliminate axial side-lobes in an effective PSF, an effective strategy is to apply defocusing to shift the foci of both objectives and create an axial misalignment between the two opposing STEDzfocal spots[38]. By performing the proposed phase manipulation using a phase mask, the disadvantages of an alternative method involving misaligning the two opposing objectives can be avoided, namely, reduced fluorescence signal and poor lateral resolution[38].Similar to the STEDzpattern,the STEDxypattern is generated by the opposing propagating beams in a constructive interference manner. Remarkably,although the intensity profile and total STED power are generally unchanged with respect to the single-objective modality,the additional interference can double the peak intensity, equivalent to a resolution enhancement of√---2times based on the modified Abbe’s equation[39].

    The ability of isoSTED nanoscopy in confining the fluorescence to the immediate vicinity of the focus creates an effective PSF that is 1500 times smaller than that of the confocal one,implying a resolution of 20–50 nm in three dimensions[23]. The significant gain over the confocal PSF renders isoSTED nanoscopy a powerful noninvasive methodology for the 3D imaging of transparent samples at the nanoscale. The applications of isoSTED nanoscopy have been demonstrated in multiple disciplines.Immediately after invention,an isoSTED nanoscope was applied in material science to image self-assembled nanostructures[40]. These structures are formed by a block copolymer system (styrene-block-2-vinylpyridine,Fig. 3(a) [40]), in which the vinylpyridine phase is specifically labeled with Atto 647N to provide fluorescence contrast.The resultant image of the confocal microscope (Fig. 3(b) [40]) does not show any features of the swelling-induced morphology, whereas,the isoSTED nanoscope provides more underlying information(Fig. 3(c) [40]). In particular, the unique strength of the isoSTED nanoscope enables a noninvasive visualization of the complete 3D structure within the sample bulk, which was previously inaccessible via electron microscopes.

    In addition to material science, the emerging importance of isoSTED nanoscopy is exemplified in cell biology. Mitochondrion,an organelle with a fundamental role in energy production, is the first imaging target of the isoSTED nanoscope. Mitochondria are bounded by two different membranes and have a typical diameter of 200–400 nm, as first revealed by electron microscopy (EM) in the 1950s [41] (Fig. 4(a) [42]). The development of isoSTED nanoscopy has enabled scientists to analyze nanoscale biological structures. By scanning a ~35 nm-diameter PSF throughout the mitochondria, isoSTED nanoscopy has successfully mapped the distribution of both F1F0-adenosine triphosphate synthase(ATPase)(Fig.4(b)[42,43])and translocase of the outer mitochondrial membrane member 20 (TOMM20) (Fig. 4(c) [23,42,43]). In another demonstration, scientists focused on synaptic vesicles[42], that is, small, electron-lucent vesicles with an average diameter of 39.5 nm[44].These synaptic vesicles,which reside in presynaptic terminals, store neurotransmitters and are essential for propagating nerve impulses between neurons. Benefitting from the ability of isoSTED nanoscopy,the spatial distribution of the surface pool in the periactive zone of the hippocampal boutons was successfully resolved.

    Despite the stronger sectioning capability of isoSTED nanoscopy over ordinary STED nanoscopy, the power level of the depletion laser required by isoSTED nanoscopy is extremely high for most living specimens.To enable live-cell imaging using 4Pi nanoscopy,4Pi-RESOLFT was developed[24]. As an isoSTED-derivative, 4Pi-RESOLFT typically replaces fluorescent dyes with RSFPs to provide‘‘on”and‘‘off”states.RSFP-based RESOLFT is particularly attractive because it operates at a low laser power(approximately two orders of magnitude lower than that required for isoSTED nanoscopy[24]), rendering it more compatible for living cells.

    3. Stochastic switching of 4Pi nanoscopy

    The optical resolution of SMLM has reached a few nanometers,thus enabling the optical analysis of nanobiostructures[45].It utilizes wide-field excitation and detection to stochastically excite and precisely localize single molecules, achieving superresolution capability. This approach is currently widely used as it is easy to implement in conventional wide-field setups[46]. The 3D-SMLM is typically implemented by evaluating the PSF with lateral information as well as with the PSF shape[11–14].Alternatively, the axial position of individual molecules can be retrieved by simultaneously imaging multiple focal planes [10]. Depending on the detected photons,this technique can achieve a lateral resolution of 20–30 nm, whereas the axial resolution is typically several-fold worse.

    Fig. 3. Application of isoSTED nanoscopy in material science. (a) Transmission electron micrograph (TEM) of solvent-annealed thin film showing lamellar structure. (b) Confocal image of block copolymer is featureless, whereas (c) isoSTED image clearly reveals the underlying morphology. a.u.:arbitrary unite.Reproduced form Ref. [40] with permission of American Chemical Society, ? 2009.

    Fig.4. Application of isoSTED nanoscopy in cell biology.(a)Dimensions of mitochondrial tubule.IsoSTED image of(b)F1F0-ATPase and(c)TOMM20 in wild-type PtK2 cells.Reproduced form Ref. [43] with permission of ACS, ? 2009.

    Compared with the conventional single-objective 3D-SMLM system, 4Pi-SMLM uses the interference of fluorescence signals detected by two opposing objectives to increase the z-resolution significantly. The two opposing objectives collect the (almost)complete spherical wavefront, thereby doubling the number of detected photons and increasing the aperture angle. Furthermore,overlaying both detection paths can result in the self-interference of individual photons when the optical path length of the two axial imaging paths is within the coherent length.Single molecules with three[25] or four[26,27] interference phases are then simultaneously recorded. As the interference phase is highly sensitive to the fluorophore’s axial position, the resulting axial resolution is approximately six to ten times higher than the axial resolution achievable using the single-objective system,surpassing the lateral resolution in some cases.

    The axial resolution for single-objective nanoscopy can reach~60 nm[11], but bright synthetic fluorophores are required. The performance obtained using dimmer fluorescent proteins (FPs) is typically poorer[47]. By contrast, 3D sub-10 nm resolution is theoretically achievable in 4Pi-SMLM with only 250 photons collected in each objective for an individual fluorophore[48].Therefore,4Pi-SMLM is suitable for imaging biological samples labeled with dimmer photoactivatable fluorescent proteins (PA-FPs). Endogenously expressed PA-FPs offer several key advantages over synthetic fluorophores[49], particularly in live-cell imaging. They can be fixed more gently as only mild fixation is required, and the cells are returned to the physiological media. In contrast to synthetic fluorophores, oxygen scavenging imaging buffers, potentially perturbative detergents, or treatments are not required to control the photophysics of single molecules.

    With an overall resolution of < 20 nm in three dimensions for dimmer PA-FPs, 4Pi-SMLM enables biologists to observe more detailed biological samples in three dimensions. Cell focal adhesions(FAs)that link the extracellular matrix to the actin cytoskeleton are crucial in morphogenesis, immunity, and wound healing[50].FAs form small(<250 nm)clustered integrins,focal adhesion kinase, and paxillin during cell edge protrusion. The multilaminar protein architecture of FAs is critical for understanding their functions. Combining 4Pi-SMLM with PA-FP-labeled FAs is an ideal approach for imaging the 3D architecture of different protein composites in FAs. Utilizing the 3D isotropic nanometer resolution capability of 4Pi-SMLM, Kanchanawong et al. [50] discovered that the vertical distributions of each FA component are highly consistent across FAs of different sizes and shapes, suggesting that the position of proteins within FAs regulates their activity and function. Using a similar strategy, Case et al. [51] regulated vinculin activation and function.

    Furthermore, 4Pi-SMLM offers quantitative biological insights into many different biological systems,particularly those requiring ultrahigh resolutions[52–56].The nanoscale organization of endosomal sorting complexes required for transport (ESCRT) machinery, which is hijacked by the human immunodeficiency virus(HIV), was resolved at the virus budding site. The spatial architecture of the ESCRT subunits suggests that the driving force for HIV release may be derived from the initial scaffolding of ESCRT subunits within the viral bud interior [54]. Two discrete barrel structures, each composed of dozens of individual Nup188 clusters,were resolved at the cilium base. The structural details support the concept that Nup199 encapsulates the centrioles within a barrel-like structure [56]. Furthermore, the 3D 4Pi-SMLM image was applied to quantify the number of proteins in the secretion machinery[52].Zhang et al.[52]demonstrated 3D molecular clusters of various sizes formed by a secretion system protein, PrgH,near the cell membrane of a bacterium (Fig. 5 [52]). Recently,4Pi-SMLM has been successfully used to resolve the 3D organization of heterogeneous nanoscale crosslinks,providing insights into the kinetics of microgel formation [57].

    In addition to the application in biology and material science,4Pi-SMLM has evolved progressively and currently offers more imaging capabilities. When the 4Pi-SMLM concept was initially realized,the imaging depth was limited to the z range of one interference period (half of the emission wavelength, ~250 nm). This is because the intensity of the interference is periodic, and intensity peaks belonging to the adjacent interferometric fringes cannot be distinguished. Two methods have been applied to solve this problem.The first method addresses this by introducing astigmatism to the 4Pi-PSF[58].Therefore,the overall shape of the PSF can be used to unwrap the interference phases in different periods, extending the imaging z depth to the extent afforded by the astigmaticbased 3D-SMLM method (~1 μm). The second method utilizes the concept wherein the emitted wavefronts are spherical rather than planar, and different oscillations of the zeroth and third central moments are investigated to precisely determine the z-position in different periods[26].Recently,adaptive optics have been introduced to 4Pi-SMLM, enabling whole-cell imaging (Fig. 6 [27]).Additionally, multicolor imaging has been introduced in 4Pi-SMLM;two-color 4Pi-SMLM imaging was first realized by attributing fluorophore color identity with the ratio of s-polarized versus p-polarized emission components[27]. Recently, three-color 4Pi-SMLM was realized using salvaged fluorescence reflected by an excitation dichroic mirror[59]. Another exciting development is correlative 4Pi-SMLM-EM imaging. The high resolution and high molecular specificity of 4Pi-SMLM combined with EM substantially reduced the resolution gap between fluorescence microscopy and EM, providing a much better overlaying of fluorescence signals with EM images[60,61].

    In contrast to single-objective 3D-SMLM,in which the theoretical limited resolution is achieved by maximum likelihood estimation using a bead-calibrated experimental PSF model[62], the conventional photometry-based 4Pi-SMLM data analysis workflow fails to reach the theoretical resolution limit[25–27].This is because the photometry-based method does not exploit the resolution gain from high-frequency information in the fringe-like interference 4Pi-PSF. The development of the cubic-spline-interpolated phaseretrieved 4Pi-PSF model can potentially reach the theoretical resolution limit presented in Ref. [63]. However, 4Pi-PSF is intrinsically four dimensional (x, y, z, and phase). A simple multichannel 3DPSF model is not well suited for describing the 4Pi-PSF. A recent 4Pi-PSF model proposed by Li et al.[64]decoupled the phase term from the 3D position of the 4Pi-PSF. Instead of using a fourdimensional 4Pi-PSF,three 3D-matrices in combination with a simple phase term were used to fully describe the four-dimensional 4Pi-PSF, rendering the calibration of an experimental 4Pi-PSF much easier in practice.Therefore,it can potentially reach the full potential of 4Pi-SMLM.

    Fig. 5. Ultrahigh resolution 3D imaging of different biological samples using 4Pi-SMLM. (a) 3D imaging of molecular clusters formed by secretion system protein PrgH near bacterial cell membrane. (b) Accumulated 4Pi-SMLM images of PrgH clusters from 58 bacterial cells. Reproduced form Ref. [52] with permission of National Academy of Science, ? 2017.

    Fig.6. 4Pi-SMLM imaging of synaptonemal complexes in whole-mouse spermatocyte. (a) Overview images of whole cell reconstructed from 21 optical sections. 4Pi-SMLM images of (b) top and (c) bottom locations inside the spermatocyte. (d) x–z view of (a). Reproduced form Ref. [27] with permission of Elsevier, ? 2016.

    4. Discussion and outlook

    Optical nanoscopy has proven to be an effective technique for investigating the molecular details of subcellular structures via specifically targeted fluorescent labels[45].It has evolved continually to provide multicolor, 3D, and live-cell imaging with nanometer-scale resolution.In particular,the highlights of all milestones in 4Pi microscopy and nanoscopy are shown in Fig. 7. Most conventional optical nanoscopes offer a resolution in the range of 50–100 nm;however,a further resolution improvement by a factor of ten would enable the 3D imaging of the molecular basis of macromolecular assemblies. This would enable biologists to directly visualize the structure and composition of molecular machinery of cells in situ; for example, 3D observations of DNA conformation at such resolutions would be critical for understanding chromosomal DNA packaging and gene regulation[65]. This can be realized by a two-order increase in the number of photons from single fluorescent emitters in stochastic switching nanoscopy or two orders of increase in depletion laser intensity in targeted switching nanoscopy. However, such a large increase in photons/intensity is typically unfavorable for practical biological experiments. By contrast, dual-objective 4Pi microscopy can substantially augment the 3D resolution of almost all single-objective far-field optical nanoscopy techniques by a three- to ten-fold improved z-resolution.It may be feasible to improve the resolution by an order of magnitude without additional requirements to satisfy the stringent properties of fluorescent labels or harsh imaging conditions.

    In addition to 4Pi nanoscopy, other schemes can be used to improve the axial resolution to the sub-50 nm level. For example,point accumulation may be employed for imaging nanoscale topography (PAINT)[66] or its extension, DNA-PAINT[67,68],which replaces the stochastic photoactivation of a permanently bound fluorophore with the stochastic binding of a fluorescent ligand during sample preparation.Another approach that improves the final resolution via sample preparation is expansion microscopy (ExM)[69,70]. By physically enlarging an organism using an expandable polymer network,ExM allows investigators to identify small structures within specimens. In terms of instrumentation, minimal photon fluxes (MINFLUX) is the cutting-edge method for precisely localizing fluorophore molecules[71,72]. In contrast to the classic SMLM that establishes molecule locations by obtaining the centroid or maximum of sparse diffraction-limited emission spots, MINFLUX probes each location with an excitation minimum. Alternatively, the recent development of artificial intelligence offers another route for transforming diffraction-limited input images into super-resolved ones[73] or to significantly reduce the illumination light doses for superresolution live-cell imaging[74].

    Fig. 7. Instrumental milestones in 4Pi microscopy and 4Pi nanoscopy.

    To date,the effects of these newly emerging techniques are primarily verified on single-objective arrangements via both microscopy and nanoscopy[71,75–79]. Notably, a fundamental barrier that rejects their integration into setups with two opposing objectives does not exist. One may expect them to provide benefits(higher 3D resolution, better SNR, etc.) similar to those of isoSTED or 4Pi-SMLM by using the 4Pi architecture. However, the major challenge is the increased system complexity:The 4Pi architecture requires a meticulous alignment with a large number of parameters in parallel, in addition to the additional system optimization required specifically for these new concepts. This issue severely compromises the system performance if it is not addressed appropriately. In fact, most 4Pi microscopes/nanoscopes are accessible only in advanced laboratories.A blue print of the 4Pi microscopes,together with open-source software and more operation protocols[80], will enable non-experts to use 4Pi nanoscopy to achieve a substantial resolution enhancement. Scientists endeavoring to simplify the setup of 4Pi nanoscopes have achieved remarkable progress. For example, in the initial setup design of the isoSTED nanoscope, two independent STED beams were implemented to generate STEDxyand STEDzprofiles. Apparently, an isoSTED setup with one STED beam can potentially reduce the complexity and improve the mechanical robustness. Hence, two ideas were proposed: One is to introduce a double-pass spatial light modulator configuration to encode separate phase profiles for each polarization component[81], and another option is to insert a segmented and chromatic wave plate[82]. Both designs have been realized and proven to facilitate routine isoSTED imaging effectively.

    Regarding the high symmetry of the 4Pi interference cavity, a more ‘‘a(chǎn)ggressive” idea is to completely remove the opposing objectives and use a flat mirror to replace the slide behind the sample in mirror-enhanced super-resolution microscopy (MEANS)

    [83]. Therefore, the incident and reflected light can mimic the opposing propagating beams in 4Pi nanoscopes, creating local interference on the mirror surface and confine the PSF in the axial direction. Initially, MEANS improved the z-resolution only in a two-dimensional (2D)-STED nanoscope. However, its importance is highlighted by its potential in benefitting both targeted and switching nanoscopies [84]. It provides a general strategy to improve the axial resolution of a single-objective nanoscope, providing access to 4Pi nanoscopy to more laboratories in a virtual manner.

    As different 4Pi super-resolution instruments have been well established, the next research focus will be on their applications to address scientific questions. The coherent use of two opposing objectives is the most effective approach if the sample is transparent and accessible from both sides. To maintain a stable interference pattern within the entire imaging process, 4Pi nanoscopy responds sensitively to aberrations induced by refractive index inhomogeneities within the sample. Although 4Pi nanoscopy is scarcely reported for cell imaging,its applications to thick samples,for example, tissues, are almost unexplored. To fully understand aberrations effects, a mathematical model that can describe aberrations in the 4Pi system with two noncontiguous circular pupils[85] is required. Hence, adaptive optics[86] should be introduced to compensate for sample-induced aberrations. This concept has inspired several researchers to conduct pioneering studies to demonstrate 4Pi imaging in whole cells[27] and tissue slices[81]. Although the applications of 4Pi imaging for thick specimens have begun, the full realization of their potential is yet to be realized. The extension of 4Pi imaging to living specimens will be critical to this process.

    Acknowledgments

    This work was financially supported by the grants from National Key Research and Development Program of China(2018YFA0701400 and 2018YFE0119000), the Fundamental Research Funds for the Central Universities (2019QNA5006), ZJUSunny Photonics Innovation Center (2019-01), Zhejiang Provincial Natural Science Foundation of China (LR18H180001), and startup grant from Southern University of Science and Technology.

    Compliance with ethics guidelines

    Xiang Hao,Yiming Li,Shuang Fu,Yanghui Li,Yingke Xu,Cuifang Kuang, and Xu Liu declare that they have no conflict of interest or financial conflicts to disclose.

    国产精品麻豆人妻色哟哟久久| 老熟妇乱子伦视频在线观看 | 新久久久久国产一级毛片| 丝袜喷水一区| 久久久水蜜桃国产精品网| 国产精品 国内视频| 免费不卡黄色视频| 精品一区二区三区av网在线观看 | 欧美黄色片欧美黄色片| 免费女性裸体啪啪无遮挡网站| 青草久久国产| 欧美另类亚洲清纯唯美| av免费在线观看网站| 国产高清视频在线播放一区 | www.999成人在线观看| 美女主播在线视频| 久久精品国产亚洲av香蕉五月 | 国产亚洲欧美精品永久| 十八禁网站免费在线| 欧美97在线视频| 日本91视频免费播放| 欧美精品高潮呻吟av久久| 久久天堂一区二区三区四区| a级片在线免费高清观看视频| 91成年电影在线观看| 大香蕉久久网| 黑丝袜美女国产一区| 亚洲一码二码三码区别大吗| 18在线观看网站| 免费在线观看黄色视频的| 日韩制服骚丝袜av| 9191精品国产免费久久| av在线app专区| 桃红色精品国产亚洲av| 欧美精品av麻豆av| 亚洲欧美日韩另类电影网站| 国产有黄有色有爽视频| a在线观看视频网站| 国产男女内射视频| 国产精品国产三级国产专区5o| 久久久欧美国产精品| 久久天躁狠狠躁夜夜2o2o| 久久久国产一区二区| 亚洲专区字幕在线| 日韩精品免费视频一区二区三区| 亚洲精品中文字幕一二三四区 | 丝袜脚勾引网站| 久久国产精品男人的天堂亚洲| 叶爱在线成人免费视频播放| 亚洲avbb在线观看| 欧美成人午夜精品| 岛国毛片在线播放| 免费不卡黄色视频| 老司机在亚洲福利影院| 欧美老熟妇乱子伦牲交| 免费观看a级毛片全部| 50天的宝宝边吃奶边哭怎么回事| 999久久久国产精品视频| 高清视频免费观看一区二区| 欧美成狂野欧美在线观看| 久久ye,这里只有精品| 一边摸一边做爽爽视频免费| 制服诱惑二区| 日韩大片免费观看网站| 老司机在亚洲福利影院| 亚洲,欧美精品.| 超色免费av| 国产精品一区二区在线不卡| 另类精品久久| 国产精品一区二区在线观看99| 18禁黄网站禁片午夜丰满| 欧美日韩福利视频一区二区| 午夜91福利影院| 精品卡一卡二卡四卡免费| 少妇 在线观看| 婷婷成人精品国产| 久久久精品免费免费高清| 大陆偷拍与自拍| 天天操日日干夜夜撸| 最新在线观看一区二区三区| 两人在一起打扑克的视频| 国产精品一区二区在线不卡| 欧美精品av麻豆av| 日日摸夜夜添夜夜添小说| 女人爽到高潮嗷嗷叫在线视频| 免费黄频网站在线观看国产| 最近最新免费中文字幕在线| 婷婷丁香在线五月| 一本久久精品| 亚洲精品一区蜜桃| 亚洲av美国av| 制服诱惑二区| 少妇人妻久久综合中文| 50天的宝宝边吃奶边哭怎么回事| 一级a爱视频在线免费观看| 免费少妇av软件| 日韩视频一区二区在线观看| 欧美成狂野欧美在线观看| 久久久久精品国产欧美久久久 | 亚洲一区中文字幕在线| 日韩 亚洲 欧美在线| 国产精品久久久av美女十八| 久久天躁狠狠躁夜夜2o2o| 欧美黄色片欧美黄色片| av网站免费在线观看视频| 97精品久久久久久久久久精品| 免费高清在线观看视频在线观看| 免费观看a级毛片全部| 久久久久视频综合| 亚洲欧美日韩另类电影网站| 婷婷色av中文字幕| 国产精品麻豆人妻色哟哟久久| 99re6热这里在线精品视频| 日韩欧美免费精品| 香蕉国产在线看| av网站在线播放免费| 日本av手机在线免费观看| 高清欧美精品videossex| 老司机在亚洲福利影院| 窝窝影院91人妻| 国精品久久久久久国模美| 九色亚洲精品在线播放| 欧美国产精品一级二级三级| 久久国产亚洲av麻豆专区| 男人爽女人下面视频在线观看| 国产精品一二三区在线看| 波多野结衣av一区二区av| 国产伦理片在线播放av一区| 色婷婷av一区二区三区视频| 亚洲avbb在线观看| 亚洲成人手机| 亚洲精品在线美女| 男人爽女人下面视频在线观看| 国产日韩欧美亚洲二区| 自拍欧美九色日韩亚洲蝌蚪91| 99久久99久久久精品蜜桃| 午夜福利视频在线观看免费| 99国产精品一区二区蜜桃av | 色老头精品视频在线观看| 成年av动漫网址| 亚洲av日韩精品久久久久久密| 精品一区二区三区四区五区乱码| 97人妻天天添夜夜摸| 久久久欧美国产精品| 久9热在线精品视频| 咕卡用的链子| 亚洲精品一二三| 亚洲一卡2卡3卡4卡5卡精品中文| 女性被躁到高潮视频| av福利片在线| 99国产精品一区二区三区| 80岁老熟妇乱子伦牲交| 美女主播在线视频| 亚洲欧美精品综合一区二区三区| 国产在线视频一区二区| 成人国语在线视频| 妹子高潮喷水视频| 90打野战视频偷拍视频| 国产成人啪精品午夜网站| 老汉色∧v一级毛片| 久久国产精品大桥未久av| 日本猛色少妇xxxxx猛交久久| 妹子高潮喷水视频| 亚洲欧美一区二区三区黑人| 一级毛片女人18水好多| 人妻 亚洲 视频| 两性夫妻黄色片| 热re99久久国产66热| 国产一区二区激情短视频 | 午夜福利乱码中文字幕| 精品熟女少妇八av免费久了| 下体分泌物呈黄色| 久久精品人人爽人人爽视色| 免费久久久久久久精品成人欧美视频| 欧美+亚洲+日韩+国产| 51午夜福利影视在线观看| 欧美久久黑人一区二区| 日韩 欧美 亚洲 中文字幕| 如日韩欧美国产精品一区二区三区| 99久久99久久久精品蜜桃| 美女国产高潮福利片在线看| 丝袜在线中文字幕| 日韩人妻精品一区2区三区| 看免费av毛片| h视频一区二区三区| 波多野结衣一区麻豆| 美国免费a级毛片| 91麻豆精品激情在线观看国产 | 亚洲第一av免费看| 99香蕉大伊视频| 两性午夜刺激爽爽歪歪视频在线观看 | 国产精品二区激情视频| 亚洲国产av新网站| 亚洲三区欧美一区| 久久精品国产亚洲av高清一级| 欧美 亚洲 国产 日韩一| 精品亚洲成国产av| 中文字幕人妻熟女乱码| 一级黄色大片毛片| 亚洲av电影在线进入| 免费av中文字幕在线| 午夜精品国产一区二区电影| 亚洲精品自拍成人| 咕卡用的链子| 欧美激情极品国产一区二区三区| 久久久精品94久久精品| 国产成人精品久久二区二区91| svipshipincom国产片| 中文字幕制服av| 夜夜夜夜夜久久久久| 日韩,欧美,国产一区二区三区| 美女主播在线视频| 在线 av 中文字幕| 俄罗斯特黄特色一大片| 日日夜夜操网爽| av欧美777| 视频区图区小说| 老司机在亚洲福利影院| 美女脱内裤让男人舔精品视频| 亚洲av电影在线观看一区二区三区| 一本综合久久免费| 久久久久久免费高清国产稀缺| 午夜福利免费观看在线| 老司机午夜十八禁免费视频| 中国国产av一级| 国产成人a∨麻豆精品| 国产亚洲一区二区精品| 欧美黄色片欧美黄色片| 黄片大片在线免费观看| 91麻豆av在线| 搡老熟女国产l中国老女人| 三上悠亚av全集在线观看| 日本黄色日本黄色录像| 亚洲五月婷婷丁香| 人人澡人人妻人| 热re99久久精品国产66热6| 久久中文看片网| 亚洲人成电影观看| 久久久久久久久免费视频了| 亚洲精品第二区| 久热这里只有精品99| 黄片大片在线免费观看| 狂野欧美激情性bbbbbb| 亚洲欧美一区二区三区黑人| 91九色精品人成在线观看| 人人妻人人爽人人添夜夜欢视频| 久久久国产一区二区| 自线自在国产av| 亚洲精品自拍成人| 男人爽女人下面视频在线观看| videosex国产| 日日爽夜夜爽网站| 久久av网站| 色综合欧美亚洲国产小说| 伊人久久大香线蕉亚洲五| 免费高清在线观看视频在线观看| 水蜜桃什么品种好| 狠狠婷婷综合久久久久久88av| 50天的宝宝边吃奶边哭怎么回事| 1024香蕉在线观看| 国产激情久久老熟女| 乱人伦中国视频| 日本av免费视频播放| 丝袜脚勾引网站| 俄罗斯特黄特色一大片| 一区二区日韩欧美中文字幕| 人妻久久中文字幕网| 三上悠亚av全集在线观看| 日韩人妻精品一区2区三区| 国产在视频线精品| 亚洲中文av在线| 中国美女看黄片| 亚洲精品日韩在线中文字幕| 欧美人与性动交α欧美软件| 精品国产一区二区三区久久久樱花| 久久热在线av| 亚洲成人国产一区在线观看| 欧美另类亚洲清纯唯美| 日韩视频在线欧美| 18禁黄网站禁片午夜丰满| 亚洲中文字幕日韩| 国产黄色免费在线视频| 色老头精品视频在线观看| 久久国产精品大桥未久av| 日本av手机在线免费观看| 国产精品久久久人人做人人爽| 国产成人欧美在线观看 | 亚洲va日本ⅴa欧美va伊人久久 | 亚洲精品av麻豆狂野| 国产91精品成人一区二区三区 | 老司机在亚洲福利影院| 男女下面插进去视频免费观看| 真人做人爱边吃奶动态| 国产在线免费精品| 91老司机精品| 日韩欧美一区视频在线观看| 中文精品一卡2卡3卡4更新| 日韩制服丝袜自拍偷拍| bbb黄色大片| 久久久精品区二区三区| 亚洲av日韩在线播放| 中文字幕高清在线视频| 国产精品.久久久| 黄色怎么调成土黄色| 两个人免费观看高清视频| 亚洲免费av在线视频| 亚洲 国产 在线| 免费观看a级毛片全部| 午夜两性在线视频| 亚洲人成电影观看| 亚洲中文字幕日韩| 国产精品偷伦视频观看了| av免费在线观看网站| 久久人妻熟女aⅴ| 亚洲欧美一区二区三区久久| 亚洲人成77777在线视频| 精品少妇久久久久久888优播| 蜜桃在线观看..| 2018国产大陆天天弄谢| 国产精品香港三级国产av潘金莲| 汤姆久久久久久久影院中文字幕| 久久久久国产一级毛片高清牌| 亚洲全国av大片| 亚洲美女黄色视频免费看| 水蜜桃什么品种好| 男女边摸边吃奶| 免费日韩欧美在线观看| 香蕉丝袜av| 亚洲国产欧美网| 啦啦啦 在线观看视频| 我的亚洲天堂| 亚洲国产日韩一区二区| 久久 成人 亚洲| 欧美日本中文国产一区发布| 亚洲欧美日韩高清在线视频 | 日韩人妻精品一区2区三区| 在线 av 中文字幕| 伊人亚洲综合成人网| 老司机亚洲免费影院| 91av网站免费观看| 亚洲精品国产av成人精品| 亚洲性夜色夜夜综合| 色播在线永久视频| 最近中文字幕2019免费版| 真人做人爱边吃奶动态| 免费高清在线观看日韩| 午夜91福利影院| 免费高清在线观看日韩| 一本久久精品| 亚洲欧美一区二区三区黑人| 热99国产精品久久久久久7| 最近中文字幕2019免费版| 王馨瑶露胸无遮挡在线观看| 免费高清在线观看日韩| 无限看片的www在线观看| 欧美日韩亚洲综合一区二区三区_| 王馨瑶露胸无遮挡在线观看| 久久人妻福利社区极品人妻图片| 亚洲av片天天在线观看| 99精国产麻豆久久婷婷| 一本综合久久免费| 亚洲精品中文字幕一二三四区 | 搡老岳熟女国产| 亚洲免费av在线视频| 亚洲中文字幕日韩| 国产成人精品久久二区二区91| 超碰成人久久| 国产免费现黄频在线看| 男女国产视频网站| 国产真人三级小视频在线观看| 国产男人的电影天堂91| 久久国产精品男人的天堂亚洲| 99久久精品国产亚洲精品| av在线播放精品| 久久久久国内视频| 91精品国产国语对白视频| 国产主播在线观看一区二区| av超薄肉色丝袜交足视频| 99九九在线精品视频| 欧美激情 高清一区二区三区| 自拍欧美九色日韩亚洲蝌蚪91| 天天躁夜夜躁狠狠躁躁| 日韩人妻精品一区2区三区| 久久精品国产综合久久久| 男女床上黄色一级片免费看| 中文字幕色久视频| 999久久久国产精品视频| 久久性视频一级片| 国产精品1区2区在线观看. | 91老司机精品| 一区二区日韩欧美中文字幕| av片东京热男人的天堂| 免费在线观看影片大全网站| 男女边摸边吃奶| 欧美乱码精品一区二区三区| 亚洲精品美女久久av网站| 国产精品一区二区在线不卡| 免费少妇av软件| 国产成人av教育| 国产无遮挡羞羞视频在线观看| 亚洲国产欧美一区二区综合| 免费在线观看视频国产中文字幕亚洲 | 最近最新免费中文字幕在线| 夜夜骑夜夜射夜夜干| 亚洲av日韩精品久久久久久密| 国产99久久九九免费精品| www.999成人在线观看| 两个人看的免费小视频| 宅男免费午夜| av天堂久久9| 国产av一区二区精品久久| 欧美中文综合在线视频| 成年动漫av网址| 国产精品免费大片| 国产亚洲午夜精品一区二区久久| 午夜老司机福利片| 精品福利观看| 纵有疾风起免费观看全集完整版| 无限看片的www在线观看| 久久人妻福利社区极品人妻图片| 丰满少妇做爰视频| 精品国产一区二区三区久久久樱花| 在线观看免费午夜福利视频| 男人爽女人下面视频在线观看| 19禁男女啪啪无遮挡网站| 国产高清videossex| 亚洲第一av免费看| 桃花免费在线播放| 黑人巨大精品欧美一区二区蜜桃| 亚洲色图 男人天堂 中文字幕| 精品少妇一区二区三区视频日本电影| 欧美xxⅹ黑人| 亚洲国产欧美网| 国产精品.久久久| 亚洲色图综合在线观看| 99精品欧美一区二区三区四区| 国产激情久久老熟女| 在线观看一区二区三区激情| 中文字幕人妻熟女乱码| 亚洲精品一卡2卡三卡4卡5卡 | 亚洲人成电影免费在线| 黄色视频在线播放观看不卡| 久久中文字幕一级| 一级毛片精品| 久久毛片免费看一区二区三区| 成人国语在线视频| 午夜精品国产一区二区电影| 超色免费av| 老司机影院成人| www.999成人在线观看| 黑人猛操日本美女一级片| av在线app专区| 欧美日韩视频精品一区| 黄色视频在线播放观看不卡| 中文字幕另类日韩欧美亚洲嫩草| 国产一区二区 视频在线| 欧美+亚洲+日韩+国产| 一级,二级,三级黄色视频| 国产成+人综合+亚洲专区| 亚洲国产日韩一区二区| 日韩 欧美 亚洲 中文字幕| 99久久精品国产亚洲精品| 91字幕亚洲| 桃红色精品国产亚洲av| 国产精品免费视频内射| 肉色欧美久久久久久久蜜桃| 午夜日韩欧美国产| 91成年电影在线观看| 少妇猛男粗大的猛烈进出视频| 欧美午夜高清在线| 免费久久久久久久精品成人欧美视频| 日本五十路高清| 亚洲人成电影观看| 亚洲精品第二区| av网站免费在线观看视频| 夜夜骑夜夜射夜夜干| 久久国产精品大桥未久av| 国产免费视频播放在线视频| 一二三四社区在线视频社区8| 国产片内射在线| 美女中出高潮动态图| 精品久久蜜臀av无| 亚洲国产毛片av蜜桃av| e午夜精品久久久久久久| 亚洲伊人色综图| 中文字幕人妻熟女乱码| 午夜激情av网站| 最近中文字幕2019免费版| 亚洲av成人一区二区三| 国产成人精品在线电影| 亚洲中文日韩欧美视频| 五月开心婷婷网| 啦啦啦中文免费视频观看日本| 人人妻人人爽人人添夜夜欢视频| 黑人欧美特级aaaaaa片| 久久av网站| 制服人妻中文乱码| 人妻 亚洲 视频| 窝窝影院91人妻| 国产欧美日韩精品亚洲av| 99国产精品99久久久久| 免费高清在线观看日韩| 亚洲五月色婷婷综合| 亚洲熟女精品中文字幕| 在线观看一区二区三区激情| 青青草视频在线视频观看| 国产精品av久久久久免费| 老熟妇乱子伦视频在线观看 | 国产在视频线精品| 国产黄频视频在线观看| 97在线人人人人妻| 国产人伦9x9x在线观看| 成在线人永久免费视频| 一二三四在线观看免费中文在| 国产极品粉嫩免费观看在线| 国产成人系列免费观看| 色视频在线一区二区三区| 亚洲性夜色夜夜综合| 亚洲五月色婷婷综合| 亚洲国产av新网站| 亚洲视频免费观看视频| 精品高清国产在线一区| av有码第一页| 精品第一国产精品| 成在线人永久免费视频| 国产日韩欧美视频二区| av片东京热男人的天堂| 黄片小视频在线播放| 国产免费一区二区三区四区乱码| 亚洲欧美精品自产自拍| 久久精品亚洲熟妇少妇任你| 久久国产精品大桥未久av| 久久久久久久久久久久大奶| 曰老女人黄片| 一级片免费观看大全| 亚洲专区国产一区二区| 日韩大码丰满熟妇| 婷婷成人精品国产| 免费高清在线观看视频在线观看| 亚洲精品第二区| 国产成人影院久久av| 欧美日韩精品网址| 亚洲精华国产精华精| 欧美成人午夜精品| 久久精品亚洲av国产电影网| 每晚都被弄得嗷嗷叫到高潮| 日本一区二区免费在线视频| 亚洲 国产 在线| 亚洲av男天堂| 欧美精品高潮呻吟av久久| 老司机午夜福利在线观看视频 | 日日爽夜夜爽网站| 久久女婷五月综合色啪小说| 黄色视频,在线免费观看| 久久热在线av| 亚洲国产精品999| 精品第一国产精品| 国产欧美日韩精品亚洲av| 久久久久久久精品精品| 欧美日韩中文字幕国产精品一区二区三区 | 久久精品亚洲熟妇少妇任你| 欧美在线一区亚洲| 99热全是精品| 久久久国产成人免费| 在线亚洲精品国产二区图片欧美| 丝袜人妻中文字幕| 国产日韩欧美视频二区| 成年人黄色毛片网站| 国产精品久久久久久精品古装| 亚洲人成电影观看| 老司机靠b影院| 免费在线观看黄色视频的| 涩涩av久久男人的天堂| 菩萨蛮人人尽说江南好唐韦庄| 天天影视国产精品| 国产高清videossex| 精品人妻熟女毛片av久久网站| 亚洲成人手机| 国产成人精品无人区| 久热爱精品视频在线9| 成人手机av| 老熟女久久久| 国产一区二区激情短视频 | 少妇粗大呻吟视频| 日本a在线网址| 水蜜桃什么品种好| 亚洲美女黄色视频免费看| 午夜精品国产一区二区电影| 日韩大片免费观看网站| 精品人妻在线不人妻| 久久久久久久久免费视频了| 91成年电影在线观看| www日本在线高清视频| 一级片免费观看大全| 黄网站色视频无遮挡免费观看| 99精品久久久久人妻精品| 欧美日韩黄片免| 别揉我奶头~嗯~啊~动态视频 | 亚洲人成电影观看| 日韩制服丝袜自拍偷拍| 国产亚洲欧美精品永久| 亚洲精品美女久久久久99蜜臀| 午夜福利影视在线免费观看| 汤姆久久久久久久影院中文字幕| 自线自在国产av| 2018国产大陆天天弄谢| 精品人妻熟女毛片av久久网站| netflix在线观看网站| 人成视频在线观看免费观看| 不卡一级毛片| 国产成人免费观看mmmm| 欧美精品高潮呻吟av久久| 亚洲综合色网址| 精品人妻一区二区三区麻豆| 自拍欧美九色日韩亚洲蝌蚪91|