• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    3D聚氨酯/聚乙烯醇縮丁醛納米纖維海綿的制備

    2021-10-23 01:05:00TavongaTrevorChadyagondo陳強施靜雅李妮
    絲綢 2021年10期
    關鍵詞:丁醛結果多孔結構

    Tavonga Trevor Chadyagondo 陳強 施靜雅 李妮

    摘要: 文章制備了具有海綿結構的聚氨酯(PU)/聚乙烯醇縮丁醛(PVB)三維(3D)納米纖維多孔結構。通過SEM、XRD和FTIR對其形貌和結構進行表征,并通過拉伸和壓縮實驗對其力學性能進行研究。SEM結果顯示,不同PU和PVB質量比的三維結構在纖維形態和纖維間交聯方面存在差異。XRD和FTIR結果證明了3D納米纖維海綿中PU和PVB聚合物分子的存在,并明確了PU分子和PVB分子間存在交聯。實驗表明,當PU和PVB質量比為7︰3時,3D納米纖維海綿中纖維形貌好,結構穩定,斷裂強力為2.2 MPa,斷裂伸長為175.5%。該多孔纖維輕質海綿具有優異的壓縮回復性能,可應用于不同的領域。

    關鍵詞:

    聚氨酯;聚乙烯醇縮丁醛;三維結構;多孔海綿;力學性能

    中圖分類號: TS102.5

    文獻標志碼: A

    文章編號: 1001-7003(2021)10-0036-08

    引用頁碼: 101107

    DOI: 10.3969/j.issn.1001-7003.2021.10.007(篇序)

    Preparation of 3D polyurethane/polyvinylbutyral nanofiber sponge

    CHADYAGONDO Tavonga Trevor, CHEN Qiang, SHI Jingya, LI Ni

    (College of Textile Science and Engineering(International Institute of Silk), Zhejiang Sci-Tech University, Hangzhou 310018, China)

    Abstract:

    In this study, a polyurethane(PU) and polyvinyl butyral(PVB) three-dimensional(3D) nanofiber porous sponge structure was prepared. Its morphology and structure were characterized by SEM, XRD and FTIR, and the mechanical properties were investigated by tensile and compressing tests. SEM results revealed that for the three-dimensional structure of different PU︰PVB ratios, there existed differences in fibre morphology and the interfibrous crosslinking. As proved by XRD and FTIR results, PU and PVB polymeric molecules existed in the 3D nanofiber sponge, and it was clarified that there exited crosslinking between PU molecules and PVB molecules. Experiments showed that when the mass ratio of PU and PVB was 7︰3, the fiber morphology of the 3D nanofiber sponge was good, the structure was stable, a breaking strength of 2.2 MPa, and a breaking elongation of 175.5%. The porous fiber lightweight sponge has excellent compression and resilience performance, and it can be applied in different fields.

    Key words:

    polyurethane; polyvinyl butyral; three-dimensional structure; porous sponge; mechanical property

    收稿日期: 2021-04-06;

    修回日期: 2021-09-14

    基金項目:

    作者簡介: Tavonga Trevor Chadyagondo(1990),男,碩士研究生,研究方向為3D納米纖維多孔結構。通信作者:李妮,副教授,lini@zstu.edu.cn。

    Electrospinning has attracted extensive attention due to its production of nanofibrous mats[1] with controllable and feasible mechanical[2] or biological properties[3-4] and its ability to change the combination of polymers to fabricate specific fibers[5]. Meanwhile, in view of some advantages of electrospun nanofibrous mats, such as large surface-to-volume ratios[6], the diversity of available materials, and the ease of surface modifications[7-8], they have been used as the substrates for various purposes[4-6].

    A sponge-like three-dimensional network structure, characterized by reversible compressibility[9], high porosity[9-10], low density, flexibility and other attractive properties, shows promising application prospect as filters[9-11], thermal insulation materials and drug delivery[3,4,9,12-13].Several papers have reported the practical approaches for producing lightweight sponge polymeric materials[14-16]. Ding Bin reported the construction of mechanically robustfibrous networks from Polyacrylonitrile(PAN) and SiO2unbonded aerogels by heating to form bonded 3Dfibrous networks, which also disclosed problems of heat shrinkage and the relaxation of orientedmolecular chains[17]. Other information explained the shortcomings of the brittleness of traditionalcolloidal aerogels[18]. Conclusions were drawn based on inherentfragility of aerogel monoliths, limiting their applications in which they were not affected by any load[19]. The mesoporoussilica structure of an aerogel was cross-linked by the reaction of di-isocyanates withsilanols on the surfaceofwet gels before supercriticaldrying[20], thereby developing a silica sponge material.

    Polyurethane(PU) is a thermoplastic elastomer withexcellent performance of wear resistance,flexibility, hydrolyticstability, stretchability, and workability at low cost[21-24]. In recentyears, PU has been studied in some literaturesin relation to its production for electrospun waterproof andbreathable functions[8,22,25-26]. Polyvinyl butyral(PVB) has been often adopted as the crosslinker/binder because of itswell-knowngood adhesion, film-forming and excellent flexibility, as well as outstanding UV resistance[27-28].

    In this paper, electrospinning and freeze-drying of dispersions of short electrospun fibers were employed to fabricate ultra-light PU/PVB sponges. The morphology and structure were examined, the tensile and compression properties of PU/PVB sponges were evaluated systematically in this study, aiming to prepare a kind of 3D nanofiber sponge with stable structure.

    1 實 驗

    1 Experiment

    1.1 材 料

    1.1 Materials

    PU(Mw=120,000 g/mol) and PVB(Mw=40 000-70 000 g/mol) were purchased from Shanghai Macklin Biochemical Co., Ltd and used without further purification. Dimethylformamide(DMF) and ethanol were bought from Hangzhou Gaojing Fine Chemical Industry Co., Ltd.

    1.2 PU/PVB納米纖維膜

    1.2 Electrospinning of PU/PVB nanofiber mat

    Several PU/PVB blends with mass ratiosranging from 8︰2, 7︰3, 6︰4 were prepared and weighed on a Mettler Toledo AL204 Balance. Then homogeneous 12% PU/PVB solution was prepared by dissolving 2.4 g of PU and PVB in DMF and stirredconstantly with amagnetic stirrer(IKA C-MAG HS7) at standard room temperature for 24 hours. In order to quantify the changes in viscosity with the alternating ratios of PU︰PVB, a rotational viscometer(NDJ-9S) was used to couple with a disc spindle to measure the dynamic viscosity. During electrospinning, the solution flow rate from the syringe pumps(KDS100) was 1 mL/hr. The applied voltage was 15 kV. Electrospinning was performed on a rotating aluminium collector plate for 10 hrs using dual needles. The distance from the tip of the needle to the rotating collector was 15 cm. The collected electrospun matwith the aluminium foil were put into a vacuum dryer at standard room temperature for at least 30 hours.

    1.3 三維PU/PVB納米纖維海綿

    1.3 Fabrication of 3D PU/PVB nanofiber sponge

    The prepared PU/PVB nanofiber mats were cut into short pieces and deposited into ethanol, and then homogenised in a high speed FJ200-SH dispersing homogeniser at a rotation speed of about 15 000 r/min for 30 min. Different short fibre dispersions were prepared by controlling the weight ratio of fibre nonwoven in the dispersion and the volume of the dispersion solvent. Then the fibre dispersion was centrifuged(Anke DZ-267-32), put into a mould and frozen at 0 ℃, and then was dried using a freeze-drier(Labonco RS232) for 48 h under a vacuum of 0.35 mbar. These steps were shown in Fig.1. The mass of the sponge was measured by a precise balance, and the volume of the sponge was calculated from the relative dimension of the fibrous 3D sponge. The density of the rectangular sponge obtained was determined by dividing the mass with the volume.

    1.4 表 征

    1.4 Characterization

    To investigate the morphology and structure of PU/PVB nanofiber mat and 3D PU/PVB nanofiber sponge, the membranes were observed using a Scanning Electron Microscope(SEM, vltra55, Germany). The microstructure of the mat and nano-sponge were evaluated using X-ray diffraction(XRD, ARL XTRA, SWISS) and Fourier Transform Infrared spectroscopy(FTIR, AVATAR5700, USA). To determine the mechanical properties of the 3D sponge, universaltensile and compression tests were performed in the paper. The tensile tests were conducted by cutting out a 4 cm by 1.5 cm strips, which were then clamped onto the test apparatus. A force was applied to the

    specimen by separating the testing machine crossheads. Data from the test were used to determine tensile strength and elongation of elasticity. The compression of 3D nano-sponge was investigated by a self-assembly experiment.

    2 結果與分析

    2 Results and analysis

    2.1 PU/PVB納米纖維膜

    2.1 PU/PVB nanofibre mats

    The general morphologies of PU/PVB nanofiber mats with mass ratios of PU/PVB blends ranging from 8︰2, 7︰3, 6︰4 were shown in Fig.2.

    The morphology of the fibre mats did not change much when varying the PVB/PU massratio 8︰2 to 7︰3. However, when the ratio reached 6︰4, the nanofiber cluttering style changed significantly, as shown in Fig.2(c). At this time, nanofibers were inhomogeneous lengthwise and they adhered together. Studies have shown that among all parameters, the viscosity of solution had a significant impact on fibre formation during spinning[29-30]. Increasing the PVB content while keeping the spinning solution at 12% would affect the spinnability of the solution because the viscosity of the solution dropped significantly(Tab.1).

    At this time, the fibre diameter reduced with the increase of PVB, which could be explained by the reduction in viscosity of the solutions[30]. In general, the reduction of viscosity results in thinner fibres though it is very difficult to then eliminate the possibility of beading when the ratio of PU to PVB is 6︰4. Meanwhile, it was found that the obtained membranes changed from soft handle to a moderately rough at higher proportion of PVB, and the 40% PVB had the toughest handle.

    2.2 納米纖維海綿

    2.2 Fibrous nano-sponge

    After building a PVB/PU short nanofiber dispersion in ethanol and setting it into a fibrous sponge via freeze drying, a self-assembled typical low weight nano-sponge was formed with significant pores, as illustrated by the images in Fig.3 and Fig.4, indicating the porosity of the sponges. PVB played a significant role in connecting short fibres with rarely short pieces of undispersed fibrous mats[31]. The optical photographand electron micrographsclearly showed points where bonds were formed between fibres and mats, forming a 3D nano-sponge complex structure. The self-assembling of the fibres was proved by the random distribution of the pores of different sizes across the nano-sponge structure. During the preparation of the 3D sponge, it was found out that when PVB content was less than 20%(PU︰PVB>8︰2), the 3D sponge with stable structure could not be formed, and short nanofibers or pieces were still separated with each other after freeze drying. At this time, it was concluded that the loose structure was due to the absence of PVB and the fact that short nanofibers or pieces could not be bound together. However, when PVB content was higher than 40%(PU︰PVB<6︰4), it was found that the nanofibers adhered together more significantly, while the characteristics of sponge porosity were weakened notably.

    A significant property elaborated by the presence of PVB was that the PU/PVB sponge could resist the disintegration from manual handle, and can in fact stretch without breaking and show impressive recovery rates even compression strength. Due to the uniform fibre diameter and desirable pore structure, PVB/PUnanofibre matswith a PU and PVB ratio of 7︰3 were used in the following XRD and FTIR discussions.

    During the preparation of 3D nano sponge, it was also found that the use of ethanol enhanced the bonding abilityof the PVB to the PU fibre structures, and yet the PU maintained the structural stability of the sponge, also highly promoted the elastic and compressional properties of the 3D nano-sponge. The 3D fibre showed a clear and strong tendency to bond across different sections due to PVB "crystallisation" during freeze drying. In this case, the the bond strength was strong enough to ignore heating, which nevertheless could be used to further improve the mechanical strength of PVBs at the glass transition temperature.

    2.3 XRD分析

    2.3 XRD analysis

    X-ray diffraction(XRD) characterization provides information about structural parameters, such as crystallinity, strain, and crystal defects, as well as many other parameters[32]. Fig.5 shows the curving graph of PU and PU/PVB fibrous material and the different PVB to PU peaks. The graph had a sharp peak, indicating a diffraction at an angle approximately 2θ=20°.

    The peak at 20° corresponded to the regular interplanar spacing corresponding to aromatic rings hard segment listed in the International Centre for Diffraction Data(ICDD). There was a shift in the position of the peak at 20°, indicating a decrease in the chain spacing. These effects indicated an increase in the crosslink that promoted the reduction of the d-spacing and the shift of the peak at 20°[33]. These peak shifts suggested there were some cross-linking patterns induced by the presence of PVB because of the general aromatic rings in PU diffract around 19°.

    PVB is completely amorphous in nature[34], which has been proved by the X-ray diffraction pattern of PU/PVB obtained and shown in Fig.5 above. This X-ray diffraction patternexhibited the characteristics of amorphous PVB. In the XRD pattern of pure PU, there was a crystalline peak around 45°, but more peaks appeared as broadened peaks at approximately 43°, indicating the presence of highly amorphous clay structure in PVB.

    2.4 FTIR結果

    2.4 FTIR results

    Fig.6 showed a full representation of the FTIR spectrum for PU, PVB and PU/PVB fibrous materials used in this research paper. The spectrum showed that the absorption bands and stretching vibrations were consistent with those of PU and PVB functional groups available in literatures[33-36]. These peaks were described and explained as follows.

    At the absorption peak between 800 cm-1 to 1 500 cm-1, there was a peak for stretching vibration of C—O—C around 1 138 cm-1 in PVB(Fig.7), which also had peaks at 1 390 cm-1 and 1 635 cm-1, indicating the band stretching for O—H and CO respectively. Another band could be observed around 1 120 cm-1, while another was seen near 1 231 cm-1, indicating that the presence of C—N and C—H bands was consistent with the PU spectrum. Furthermore, there was an absorption band at 1 721 cm-1, representing the CO stretch in PU. The curves in Fig.6 strongly showed the presence of asymmetrical and symmetrical stretching vibration of C—H bonds at around 2 866 cm-1, 2 964 cm-1 and 2 983 cm-1. These were important absorption bands because their changing intensity which explained the crosslinking physical bonding of the overall 3D structure. Finally, there were two peaks as shown in Fig.8 at between 3 300 cm-1 to 3 450 cm-1, showing the stretching vibrations of N—H and O—H functional groups in PVB and PU. The peak intensities varied with the change in content of PU and PVB during the construction of the 3D edifice due to the presence of the polarity of functional groups at such band stretches in the PU, PVB and or PU/PVB polymers[33-36].

    A notable manifestation of peak differences on the curves signaling interaction between PVB and PU could be seen in Fig.8, which differed in intensity ranging from 2 866 cm-1 to 2 983 cm-1. Despite the presence of the peaks at this range on the PVB spectrum, there was an interchanged peak size for asymmetric and symmetric C—H vibrations, which was also a prominent difference. PU/PVB membrane showed longer peaks while PU/PVB 3D model and PU membrane manifested shorter ones respectively. The peaks for PU/PVB(both membrane and 3D model) were analyzed, and the spectrum showed that the concentration of the C—H stretching vibration increased significantly, as shown by the increase in spectra intensity between 2 800 cm-1-3 000 cm-1 when compared to the PU membrane. The increase in the intensity proved that both PU and PVB existed in the fibrous membrane and 3D sponge. PU was the backbone of the structure, while PVB mainly functioned as a crosslinking agent.

    The transformation of the PU/PVB membrane into a 3D structure with ethanol as a dispersing agent reduced the amount of PVB within the fibrous matrix, and yet controlled the dispersion. The subsequent washing and freeze dry method ensured that the dissolved PVB became a crosslinking agent when dried. The spectrum for PU/PVB 3D sponge showed that the peaks in the range of 2 800 cm-1-3 000 cm-1 were still in a range comparable to those of the PU/PVB membrane, showing noteworthy difference in peak intensity. There was a decrease in intensity when comparing fibrous 3D sponge to the fibrous membrane, yet still above the peak intensity of PU only membrane, suggesting that some PVB was lost along with the ethanol solvent during the washing process, but the remaining PVB was essential for the new strongly crosslinked fibre sponge. In contrast, the curves at 3 300 cm-1 to 3 450 cm-1 changed their shape by broadening or rather increasing the area under the curve in this case. This attribute was caused by the formation of strong hydrogen bonds between N—H and O—H molecules present in both PU and PVB polymers. The change in shape also explained a weakened polarity there in came due to the interactions between functional groups.

    2.5 拉伸性能

    2.5 Stretching performance

    In a bid to understand how the sponge would react to different external forces in the form of stress and strain, PVB/PU nano-sponges with different mass ratios of PVB and PU were subjected to these forces on a tensiometer. The samples resembled strength as would be expected from their nature just as reported in other papers for aerogels and pure PVB and pure PU[17]. The main difference was that the depiction of strengths altered due to the presence of different mass ratios of PVB and PU used for sponge moulding.

    The sponge with a PU/PVB ratio of 7︰3 exhibited the highest yield point to stress, as shown in Tab.2. A measurement of over 2 MPa for this model was recorded as it showed different deformations along its length. It exhibited a significant break above 100% strain, which would be consistent with the reported resistance of either PU or PVB electrospun membrane[11,23,27]. However, the breaking points of the models was less than the fibre mats[7], which was attributed to the presence of many randomly entangled short fibres in the sponge structure. The intensified test for 40% PVB model showedthat the plastic deformation indentations were less significant, while the yield stress was lower, which was attributed to the decreased PU and strengthened bonding between fibres.

    2.6 壓縮實驗

    2.6 Compression test

    A manual compression recovery test was performed on the 3D fibrous sponges to show their recovery capabilities after being compressed by a force(Fig.9). The sample in Fig.9 had a weight of 0.076 5 g and an approximated volume of above 0.5 cm-3. Fig.9 showed that as soon as the fore was removed from the compressed sponge, it immediately recovered to original height. This phenomenon of instantaneous recovery to approximately the initial length could be observed even after repeated compressions. compared to other organic and inorganic building blocks for 3D sponge materials, the use of electrospun nanofibrous materials played a major role because of a better distribution of stress and strain on nanosized fibres.

    3 結 論

    3 Conclusions

    The combination of polymeric compound for the fabrication of a stable and useful structure by taking advantage of their different properties is an extensive research field among many polymers. This research work provided a versatile 3D nano-sponge, which was prepared with the ratio of PVB to PU of 7︰3, presenting uniform nanofiber and desirable morphology. Meanwhile, the nano-sponge exhibited a high tensile strength of 2.2 MPa and notable extensibility with 175.5% elongation. It also could recover instantly after compression.

    參考文獻:

    [1]FATHONA I W, KHAIRURRIJAL, YABUKIA. One-step fabrication of short nanofibers by electrospinning: effect of needle size on nanofiber length[J]. Advanced Materials Research, 2014, 896: 33-36.

    [2]TEO W E, RAMAKRISHNA S. A review on electrospinning design and nanofibre assemblies[J]. Nanotechnology, 2006, 17(14): R89.

    [3]LU W, SUN J, JIANG X. Recent advances in electrospinning technology and biomedical applications of electrospun fibers[J]. Journal of Materials Chemistry B, 2014, 2(17): 2369.

    [4]SILL T J, VON RECUM H A. Electrospinning: applications in drug delivery and tissue engineering[J]. Biomaterials, 2008, 29(13): 1989-2006.

    [5]BHARDWAJ N, KUNDU S C. Electrospinning: a fascinating fiber fabrication technique[J]. Biotechnology Advances, 2010, 28(3): 325-347.

    [6]MISHRA R, MILITKY J, VENKATARAMAN M. Electrospun nanofibers[J]. Nanotechnology in Textiles, 2019, 2: 35-161.

    [7]DONG Y, ZHENG Y, ZHANG K, et al. Electrospun nanofibrous materials for wound healing[J]. Advanced Fiber Materials, 2020, 2: 212-227.

    [8]LI P, ZHANG Q, CHADYAGONDO T T, et al. Designing waterproof and breathable fabric based on polyurethane/silica dioxide web fabricated by electrospinning[J]. Fibers and Polymers, 2020, 21(7): 1444-1452.

    [9]KIM, JONG, GIL, et al. Homogenized electrospun nanofiber reinforced microporous polymer sponge[J]. Chemical Engineering Journal, 2016, 306: 242-250.

    [10]CHEN Z, JIN L, HAO W, et al. Synthesis and applications of three-dimensional graphene network structures[J]. Materials Today Nano, 2019, 5: 100027.

    [11]WU Y, YI N, HUANG L, et al. Three-dimensionally bonded spongy graphene material with super compressive elasticity and near-zero Poissons ratio[J]. Nature Communications, 2015, 6: 6141.

    [12]CHEN D R, CHANG X H, JIAO X L. Aerogels in the environment protection[J]. The Role of Colloidal Systems in Environmental Protection, 2014: 573-591.

    [13]INGAVLE G C, LEACH J K. Advancements in electrospinning of polymeric nanofibrous scaffolds for tissue engineering[J]. Tissue Engineering Part B-Reviews, 2014, 20(4): 277-293.

    [14]CHEONG J Y, MAFI M, BENKER L, et al. Ultralight, structurally stable electrospun sponges with tailored hydrophilicity as a novel material platform[J]. ACS Applied Materials & Interfaces, 2020, 12(15): 18002.

    [15]JI H, ZHAO R, ZHANG N, et al. Lightweight and flexible electrospun polymer nanofiber/metal nanoparticle hybrid membrane for high-performance electromagnetic interference shielding[J]. NPG Asia Materials, 2018, 10(8): 749-60.

    [16]DUAN G, JIANG S, JEROME V, et al. Ultralight, soft polymer sponges by self-assembly of short electrospun fibers in colloidal dispersions[J]. Advanced Functional Materials, 2015, 25(19): 2850-2856.

    [17]YANG S, YU J, TANG X, et al. Ultralight nanofibre-assembled cellular aerogels with superelasticity and multifunctionality[J]. Nature Communications, 2014, 5: 5802.

    [18]MALEKI H, WHITMORE L, HSING N. Novel multifunctional polymethylsilsesquioxane-silk fibroin aerogel hybrids for environmental and thermal insulation applications[J]. Journal of Materials Chemistry A, 2018, 6(26): 12598-612.

    [19]MEADOR M A B, CAPADONA L A, ORKLE L, et al. Structure property relationships in porous 3D nanostructures as a function of preparation conditions: isocyanate cross-linked silica aerogels[J]. Chemistry of Materials, 2007, 19(9): 2247-2260.

    [20]MEADORMAB, VIVODSL, MCCORKLE L, et al. Reinforcing polymer cross-linked aerogels with carbon nanofibers[J]. Journal of Materials Chemistry, 2008, 18(16): 1843-1852.

    [21]AKDUMAN C, KUMBASAR E. Electrospun Polyurethane Nanofibers[M]. United Kingdom: In Tech Open, 2017.

    [22]RUI C, CHEN H, KE Q, et al. Preparation and characterization of coaxial electrospun thermoplastic polyurethane/collagen compound nanofibers for tissue engineering applications[J]. Colloids & Surfaces B Biointerfaces, 2010, 79(2): 315-325.

    [23]CHUNG Y C, CHOI J W, MOON S, et al. Effect of cross-linking agent structure on the shape memory property of polyurethane block copolymer[J]. Fibers and Polymers, 2009, 10(4): 430-436.

    [24]PENG L, ZHOU L, LI Y, et al. Synthesis and properties of waterborne polyurethane/attapulgite nanocomposites-science direct[J]. Composites Science and Technology, 2011, 71(10): 1280-1285.

    [25]XU Y, SHENG J, YIN X, et al. Functional modification of breathable polyacrylonitrile/polyurethane/TiO2 nanofibrous membranes with robust ultraviolet resistant and waterproof performance[J]. Journal of Colloid and Interface Science, 2017, 508: 508-516.

    [26]GU X, LI N, LUO J, et al. Electrospun polyurethane microporous membranes for waterproof and breathable application: the effects of solvent properties on membrane performance[J]. Polymer Bulletin, 2018, 75(8): 3539-53.

    [27]PEER P, STENICKA M, PAVLINEK V, et al. An electrorheological investigation of PVB solutions in connection with their electrospinning qualities[J]. Polymer Testing, 2014, 39: 115-21.

    [28]ZHANG Min, SHENG Junlu, YIN Xia, etal. Polyvinyl butyral modified polyvinylidene fluoride breathable-waterproof nanofibrous membranes with enhanced mechanical performance[J]. Macromolecular Materials and Engineering, 2017, 302(8): 1600272.

    [29]CHANG F C. The Effect of processing parameters on formation of lignosulfonate fibers produced using electrospinning technology[J]. Bioresources, 2016, 11(2): 4705-4717.

    [30]RAY S S, CHEN S S, NGUYEN N C, et al. Electrospinning: aversatile fabrication technique for nanofibrous membranes for use in desalination[J]. Nanoscale Materials in Water Purification, 2019, 9: 247-273.

    [31]LANGNER M, GREINER A. Wet-laid meets electrospinning: nonwovens for filtration applications from short electrospun polymer nanofiber dispersions[J]. Macromolecular Rapid Communications, 2016, 37(4): 351-355.

    [32]BUNACIU A A, UDRITIOIU E G, ABOUL-ENEIN H Y. X-ray diffraction: instrumentation and applications[J]. Critical Reviews in Analytical Chemistry, 2015, 45(4): 289-299.

    [33]TROVATI G, SANCHES E A, NETO S C, et al. Characterization of polyurethane resins by FTIR, TGA, and XRD[J]. Journal of Applied Polymer Science, 2010, 115(1): 263-268.

    [34]PISTEK D, MERINSKA D, DUJKOVA Z, et al. The mechanical and optical properties of the PVB nanocomposites[C]//Proceedings of the 3rd WSEAS International Conference on Advances in Sensors, Signals and Materials. Faro, Portugal: World Scientific and Engineering Academy and Society(WSEAS), 2010: 26-29.

    [35]BINTI K, HAJI BADRI K, MAISARA S, et al. FTIR spectroscopy analysis of the prepolymerization of palm-based polyurethane[J]. Solid State Technology, 2010, 18: 1-8.

    [36]MARTN M, CENTELLES X, SOL A, et al. Polymeric interlayer materials for laminated glass: a review[J]. Construction and Building Materials, 2020, 230: 116897.

    猜你喜歡
    丁醛結果多孔結構
    The Ways Of Studying
    不同梯度變化方式的不規則多孔結構設計與力學性能分析
    I-WP型極小曲面空心多孔結構設計與力學性能分析
    不規則多孔結構鈦合金人體植入物的制備和性能研究
    丁醇裝置聯產異丁醛的分析與模擬
    山東化工(2020年5期)2020-04-07 09:59:32
    3DP法三維打印金屬多孔結構基本打印單元的研究
    跟蹤導練(三)2
    合理表示“等可能事件”的所有結果
    刷碗
    錳離子催化臭氧氧化氣相丁醛
    av国产久精品久网站免费入址| 天堂俺去俺来也www色官网| 美女国产视频在线观看| 美女脱内裤让男人舔精品视频| 性高湖久久久久久久久免费观看| 人妻制服诱惑在线中文字幕| 国产无遮挡羞羞视频在线观看| 久久综合国产亚洲精品| 3wmmmm亚洲av在线观看| 亚洲熟女精品中文字幕| 亚洲精品视频女| 国产精品偷伦视频观看了| 欧美日韩视频精品一区| 国产高清有码在线观看视频| 成人亚洲欧美一区二区av| 直男gayav资源| 热99国产精品久久久久久7| 少妇人妻久久综合中文| 亚洲精品日韩av片在线观看| av视频免费观看在线观看| 精品一区在线观看国产| 又大又黄又爽视频免费| 蜜臀久久99精品久久宅男| 亚洲国产高清在线一区二区三| 亚洲成色77777| www.av在线官网国产| 一个人看视频在线观看www免费| 日韩在线高清观看一区二区三区| av专区在线播放| 联通29元200g的流量卡| 男女无遮挡免费网站观看| 午夜免费男女啪啪视频观看| 久久国产精品男人的天堂亚洲 | 黄片无遮挡物在线观看| 国产欧美亚洲国产| av女优亚洲男人天堂| 亚洲高清免费不卡视频| 精品少妇久久久久久888优播| 丰满乱子伦码专区| 97在线视频观看| 欧美另类一区| 亚洲精品国产色婷婷电影| 国产精品爽爽va在线观看网站| 少妇的逼好多水| 国产成人精品婷婷| 一级毛片 在线播放| 成人国产麻豆网| 日韩大片免费观看网站| 嫩草影院新地址| 亚洲精品中文字幕在线视频 | 久久久久久久久久成人| 婷婷色综合大香蕉| 成人无遮挡网站| av线在线观看网站| 天堂中文最新版在线下载| 我的女老师完整版在线观看| 国产精品嫩草影院av在线观看| 精品亚洲成a人片在线观看 | 免费看日本二区| 国产毛片在线视频| 精华霜和精华液先用哪个| 嫩草影院新地址| 如何舔出高潮| 午夜视频国产福利| 1000部很黄的大片| 国产国拍精品亚洲av在线观看| 男男h啪啪无遮挡| 如何舔出高潮| 成人高潮视频无遮挡免费网站| 色网站视频免费| 菩萨蛮人人尽说江南好唐韦庄| 国产精品久久久久久av不卡| 国产 一区 欧美 日韩| 人体艺术视频欧美日本| 丰满人妻一区二区三区视频av| 国产在视频线精品| 另类亚洲欧美激情| 少妇丰满av| 毛片一级片免费看久久久久| 少妇精品久久久久久久| 天天躁夜夜躁狠狠久久av| 精品久久国产蜜桃| 国产精品久久久久久精品古装| 伦精品一区二区三区| 国产午夜精品久久久久久一区二区三区| 成人漫画全彩无遮挡| 黄色视频在线播放观看不卡| 麻豆成人av视频| 亚洲欧美精品专区久久| 男男h啪啪无遮挡| av在线app专区| 国产有黄有色有爽视频| 国产亚洲午夜精品一区二区久久| 超碰97精品在线观看| 久久久久国产网址| 色吧在线观看| 国产黄色视频一区二区在线观看| 国产精品99久久久久久久久| 菩萨蛮人人尽说江南好唐韦庄| av国产久精品久网站免费入址| 老女人水多毛片| 免费观看在线日韩| 男女边吃奶边做爰视频| 久久久久久久国产电影| 午夜福利在线观看免费完整高清在| 啦啦啦在线观看免费高清www| 中国美白少妇内射xxxbb| 小蜜桃在线观看免费完整版高清| 男人舔奶头视频| 美女xxoo啪啪120秒动态图| 国产无遮挡羞羞视频在线观看| 久热这里只有精品99| 亚洲一区二区三区欧美精品| 久久精品久久精品一区二区三区| 国产成人a区在线观看| 我的老师免费观看完整版| 国产男女内射视频| 国产精品伦人一区二区| 久久久久久久久久人人人人人人| 日韩制服骚丝袜av| 日本午夜av视频| 秋霞伦理黄片| 在线亚洲精品国产二区图片欧美 | 最近最新中文字幕大全电影3| 大香蕉97超碰在线| 男人和女人高潮做爰伦理| 婷婷色综合www| 亚洲国产精品成人久久小说| 免费看日本二区| 乱码一卡2卡4卡精品| 熟妇人妻不卡中文字幕| 国产精品久久久久久精品古装| 性色av一级| 亚洲精品中文字幕在线视频 | 国产男女内射视频| av免费在线看不卡| 免费av中文字幕在线| 王馨瑶露胸无遮挡在线观看| 亚洲精品乱久久久久久| 高清日韩中文字幕在线| 久久99热这里只有精品18| 少妇丰满av| 在线看a的网站| 尾随美女入室| 五月开心婷婷网| 视频区图区小说| 最后的刺客免费高清国语| 亚洲三级黄色毛片| 自拍偷自拍亚洲精品老妇| 久久国产亚洲av麻豆专区| 国产日韩欧美亚洲二区| 男的添女的下面高潮视频| 国产精品一区二区在线不卡| 99久久人妻综合| 大话2 男鬼变身卡| 日日摸夜夜添夜夜爱| 国产乱人偷精品视频| 日韩欧美 国产精品| 国产高清国产精品国产三级 | www.色视频.com| 日韩亚洲欧美综合| 中文资源天堂在线| 18禁裸乳无遮挡动漫免费视频| 黄色视频在线播放观看不卡| 人人妻人人澡人人爽人人夜夜| 欧美精品国产亚洲| 国产91av在线免费观看| 天堂中文最新版在线下载| 久久ye,这里只有精品| 91精品国产九色| 黑丝袜美女国产一区| 国产成人精品婷婷| 亚洲美女搞黄在线观看| 国产高潮美女av| 综合色丁香网| 精品一品国产午夜福利视频| 成人国产麻豆网| 成年人午夜在线观看视频| 国产毛片在线视频| 国产亚洲欧美精品永久| 在线免费观看不下载黄p国产| 高清视频免费观看一区二区| 久久久久视频综合| 美女视频免费永久观看网站| 午夜福利网站1000一区二区三区| 欧美一区二区亚洲| 成年av动漫网址| 99国产精品免费福利视频| 日本vs欧美在线观看视频 | 另类亚洲欧美激情| 亚洲一级一片aⅴ在线观看| 少妇熟女欧美另类| 三级经典国产精品| 成人18禁高潮啪啪吃奶动态图 | 亚洲欧美清纯卡通| 内射极品少妇av片p| 精品一区二区免费观看| 成年免费大片在线观看| 人妻夜夜爽99麻豆av| 欧美日韩视频高清一区二区三区二| 亚洲美女搞黄在线观看| 亚洲欧美精品专区久久| 夜夜骑夜夜射夜夜干| 久久久欧美国产精品| 国内揄拍国产精品人妻在线| 亚洲精品成人av观看孕妇| 成人免费观看视频高清| 国产精品女同一区二区软件| 成人一区二区视频在线观看| 精品一区二区免费观看| 蜜桃亚洲精品一区二区三区| 精品人妻偷拍中文字幕| 免费观看的影片在线观看| 麻豆成人av视频| 爱豆传媒免费全集在线观看| 亚洲不卡免费看| 男女啪啪激烈高潮av片| 亚洲成人手机| 日韩国内少妇激情av| 国产成人精品婷婷| 又爽又黄a免费视频| 男人舔奶头视频| 欧美成人一区二区免费高清观看| 欧美人与善性xxx| av又黄又爽大尺度在线免费看| 色视频www国产| 你懂的网址亚洲精品在线观看| 噜噜噜噜噜久久久久久91| 亚洲av在线观看美女高潮| 男女啪啪激烈高潮av片| 日韩亚洲欧美综合| 亚洲成人av在线免费| av一本久久久久| 高清毛片免费看| 日日啪夜夜撸| 国产片特级美女逼逼视频| 久久鲁丝午夜福利片| 亚洲内射少妇av| 国产欧美日韩一区二区三区在线 | 国产有黄有色有爽视频| 午夜福利视频精品| 十八禁网站网址无遮挡 | 国产 精品1| 免费av不卡在线播放| 丰满乱子伦码专区| av在线老鸭窝| 国产成人91sexporn| 人妻少妇偷人精品九色| 国产日韩欧美亚洲二区| 欧美日韩综合久久久久久| 只有这里有精品99| 国产亚洲欧美精品永久| 国产高清有码在线观看视频| 久久人人爽人人片av| 中文字幕人妻熟人妻熟丝袜美| 大香蕉久久网| 久久国产乱子免费精品| 中国国产av一级| 蜜桃亚洲精品一区二区三区| 麻豆成人av视频| 这个男人来自地球电影免费观看 | 高清在线视频一区二区三区| 亚洲成色77777| 九九久久精品国产亚洲av麻豆| 高清不卡的av网站| 女的被弄到高潮叫床怎么办| 人人妻人人爽人人添夜夜欢视频 | .国产精品久久| 美女国产视频在线观看| 欧美成人a在线观看| 亚洲国产精品国产精品| 亚洲久久久国产精品| 欧美xxⅹ黑人| 99热国产这里只有精品6| 国产综合精华液| 人妻少妇偷人精品九色| 中文字幕免费在线视频6| 插逼视频在线观看| 一级片'在线观看视频| 在现免费观看毛片| 精品99又大又爽又粗少妇毛片| 看十八女毛片水多多多| 美女国产视频在线观看| 99久国产av精品国产电影| 精品久久久噜噜| 91午夜精品亚洲一区二区三区| 精品久久久久久久久av| 国产淫片久久久久久久久| 国产在线男女| 国产极品天堂在线| 天美传媒精品一区二区| 在线亚洲精品国产二区图片欧美 | 欧美xxxx性猛交bbbb| 国产伦在线观看视频一区| 日本与韩国留学比较| 搡老乐熟女国产| 亚洲三级黄色毛片| 亚洲精品色激情综合| 老熟女久久久| 一区二区av电影网| 纯流量卡能插随身wifi吗| 婷婷色麻豆天堂久久| 亚洲va在线va天堂va国产| 在线播放无遮挡| 免费播放大片免费观看视频在线观看| 搡老乐熟女国产| 黄色视频在线播放观看不卡| 午夜视频国产福利| 午夜福利高清视频| 久久99热这里只频精品6学生| 国产亚洲一区二区精品| h视频一区二区三区| 交换朋友夫妻互换小说| av一本久久久久| 18禁动态无遮挡网站| 成人亚洲精品一区在线观看 | 大香蕉97超碰在线| av视频免费观看在线观看| 国内少妇人妻偷人精品xxx网站| 国产综合精华液| 国产高潮美女av| 26uuu在线亚洲综合色| 在线观看免费高清a一片| 久久久久久久久久久丰满| 三级国产精品欧美在线观看| 久久人人爽av亚洲精品天堂 | 国产高清有码在线观看视频| 亚洲国产日韩一区二区| 高清不卡的av网站| 成人免费观看视频高清| 美女内射精品一级片tv| 国产黄片美女视频| 六月丁香七月| 人体艺术视频欧美日本| 视频中文字幕在线观看| 精品久久久噜噜| 日本色播在线视频| 91在线精品国自产拍蜜月| 久热久热在线精品观看| 免费观看av网站的网址| 麻豆国产97在线/欧美| 天堂俺去俺来也www色官网| 色综合色国产| av又黄又爽大尺度在线免费看| 秋霞在线观看毛片| 国产一区二区三区综合在线观看 | 性色avwww在线观看| 青春草视频在线免费观看| 国产黄频视频在线观看| 最近手机中文字幕大全| 天堂中文最新版在线下载| 春色校园在线视频观看| 三级国产精品欧美在线观看| 人妻少妇偷人精品九色| 亚洲av中文av极速乱| 熟女人妻精品中文字幕| 91午夜精品亚洲一区二区三区| 国产 精品1| 久久久久久九九精品二区国产| av女优亚洲男人天堂| 国产免费一级a男人的天堂| 国产精品嫩草影院av在线观看| 亚洲欧美精品自产自拍| 亚洲国产精品成人久久小说| 亚洲精品亚洲一区二区| 性色av一级| 91aial.com中文字幕在线观看| 久久精品久久久久久久性| av在线观看视频网站免费| 51国产日韩欧美| 中文天堂在线官网| 亚洲精品成人av观看孕妇| 日日啪夜夜撸| 妹子高潮喷水视频| 看非洲黑人一级黄片| 欧美极品一区二区三区四区| 久久99蜜桃精品久久| 国产淫片久久久久久久久| 亚洲久久久国产精品| 欧美日韩在线观看h| 91精品伊人久久大香线蕉| 精品一品国产午夜福利视频| 一区二区av电影网| 久久久久国产精品人妻一区二区| 亚洲最大成人中文| 18禁裸乳无遮挡动漫免费视频| 国产一级毛片在线| 国产一区二区三区综合在线观看 | 婷婷色麻豆天堂久久| 日本爱情动作片www.在线观看| 老女人水多毛片| 国产精品偷伦视频观看了| 丰满少妇做爰视频| 国产伦理片在线播放av一区| 色婷婷av一区二区三区视频| 99热全是精品| 高清午夜精品一区二区三区| 欧美精品国产亚洲| 干丝袜人妻中文字幕| 欧美xxⅹ黑人| 亚洲精品久久午夜乱码| 欧美97在线视频| 欧美bdsm另类| 国产淫片久久久久久久久| 国产黄片美女视频| 中国国产av一级| 欧美一级a爱片免费观看看| 亚洲真实伦在线观看| 亚洲欧美日韩卡通动漫| 秋霞伦理黄片| av免费观看日本| 日韩欧美精品免费久久| 人妻一区二区av| 亚洲欧洲国产日韩| 2021少妇久久久久久久久久久| 80岁老熟妇乱子伦牲交| av在线观看视频网站免费| 国产高清有码在线观看视频| 少妇精品久久久久久久| 国产真实伦视频高清在线观看| 久久久色成人| 99re6热这里在线精品视频| av免费在线看不卡| 日本黄色片子视频| 国产免费福利视频在线观看| 日日摸夜夜添夜夜爱| 小蜜桃在线观看免费完整版高清| 亚洲av.av天堂| 人妻系列 视频| 精品熟女少妇av免费看| 亚洲,一卡二卡三卡| 精品久久久噜噜| 99热国产这里只有精品6| 一本一本综合久久| 亚洲在久久综合| 国国产精品蜜臀av免费| 少妇精品久久久久久久| 看非洲黑人一级黄片| 少妇 在线观看| 99国产精品免费福利视频| 亚洲国产欧美在线一区| 久久精品久久久久久久性| 国产熟女欧美一区二区| 男女边吃奶边做爰视频| 国产v大片淫在线免费观看| 欧美精品一区二区大全| 国产精品欧美亚洲77777| 在线观看人妻少妇| 久久国产乱子免费精品| 亚洲精品日本国产第一区| 欧美+日韩+精品| 国产精品欧美亚洲77777| 中文字幕制服av| 三级国产精品欧美在线观看| 国产成人a∨麻豆精品| 国产成人一区二区在线| 欧美国产精品一级二级三级 | 国产日韩欧美亚洲二区| av在线观看视频网站免费| 国产精品国产三级国产专区5o| 最黄视频免费看| 美女高潮的动态| 黄片wwwwww| 国产在视频线精品| 久久人妻熟女aⅴ| 欧美精品亚洲一区二区| 只有这里有精品99| 麻豆乱淫一区二区| 日韩av在线免费看完整版不卡| a 毛片基地| 中文天堂在线官网| 国产 精品1| 男的添女的下面高潮视频| 麻豆精品久久久久久蜜桃| 久久精品久久久久久噜噜老黄| 十八禁网站网址无遮挡 | 欧美成人午夜免费资源| 亚洲av福利一区| 亚洲av中文字字幕乱码综合| 一区二区三区四区激情视频| 国产有黄有色有爽视频| 一级黄片播放器| 亚洲天堂av无毛| 伊人久久国产一区二区| 欧美少妇被猛烈插入视频| 十八禁网站网址无遮挡 | 观看免费一级毛片| av一本久久久久| 色综合色国产| 久久久久精品性色| av免费观看日本| 国产色爽女视频免费观看| 欧美国产精品一级二级三级 | 日韩精品有码人妻一区| 日韩电影二区| 国产av国产精品国产| 午夜福利在线观看免费完整高清在| 久久久久性生活片| 26uuu在线亚洲综合色| 精品久久久噜噜| 天堂8中文在线网| av天堂中文字幕网| 国产中年淑女户外野战色| 美女主播在线视频| 日本欧美视频一区| 少妇裸体淫交视频免费看高清| 国产男女超爽视频在线观看| 黄色视频在线播放观看不卡| 在线观看一区二区三区| 成人一区二区视频在线观看| 国精品久久久久久国模美| 大话2 男鬼变身卡| 91精品国产九色| 日韩三级伦理在线观看| 亚洲久久久国产精品| 中文字幕精品免费在线观看视频 | 免费不卡的大黄色大毛片视频在线观看| 中文字幕免费在线视频6| 欧美精品一区二区免费开放| 欧美丝袜亚洲另类| 身体一侧抽搐| 亚洲av免费高清在线观看| 久久人妻熟女aⅴ| 丰满少妇做爰视频| 亚洲色图av天堂| 久久国产亚洲av麻豆专区| 女人久久www免费人成看片| 天美传媒精品一区二区| 亚洲最大成人中文| 高清不卡的av网站| 亚洲色图av天堂| 亚洲高清免费不卡视频| 少妇高潮的动态图| 男男h啪啪无遮挡| 美女脱内裤让男人舔精品视频| 美女cb高潮喷水在线观看| 日本免费在线观看一区| 2021少妇久久久久久久久久久| 高清黄色对白视频在线免费看 | 亚洲人与动物交配视频| 汤姆久久久久久久影院中文字幕| 性色av一级| 精品久久久久久久久亚洲| 精品99又大又爽又粗少妇毛片| www.色视频.com| av在线老鸭窝| 日韩av免费高清视频| 久久毛片免费看一区二区三区| 欧美一区二区亚洲| 亚洲在久久综合| 亚洲高清免费不卡视频| 国产av码专区亚洲av| 国产乱来视频区| 18禁裸乳无遮挡动漫免费视频| 亚洲无线观看免费| 热99国产精品久久久久久7| 国产精品无大码| 亚洲人成网站在线播| 亚洲真实伦在线观看| a 毛片基地| 日韩av不卡免费在线播放| av国产久精品久网站免费入址| 少妇的逼水好多| 日韩av免费高清视频| 少妇的逼水好多| 亚洲精品国产色婷婷电影| 不卡视频在线观看欧美| 国产黄片视频在线免费观看| 成人高潮视频无遮挡免费网站| 久久久久久久精品精品| 在线精品无人区一区二区三 | 久久久精品免费免费高清| 2018国产大陆天天弄谢| 久久久精品免费免费高清| 99九九线精品视频在线观看视频| 伊人久久精品亚洲午夜| 91精品伊人久久大香线蕉| 夜夜看夜夜爽夜夜摸| 国产精品一区www在线观看| 边亲边吃奶的免费视频| 97精品久久久久久久久久精品| 久久99精品国语久久久| 久热久热在线精品观看| 少妇人妻久久综合中文| 亚洲丝袜综合中文字幕| 久久综合国产亚洲精品| 亚洲成色77777| 国产片特级美女逼逼视频| 国产亚洲5aaaaa淫片| 嘟嘟电影网在线观看| 美女国产视频在线观看| 精品一品国产午夜福利视频| 偷拍熟女少妇极品色| 成人亚洲精品一区在线观看 | 久久这里有精品视频免费| 天美传媒精品一区二区| 国产av精品麻豆| 毛片女人毛片| 22中文网久久字幕| 黄色视频在线播放观看不卡| 国产午夜精品久久久久久一区二区三区| 妹子高潮喷水视频| 日韩制服骚丝袜av| 青春草视频在线免费观看| 成人影院久久| 伦理电影大哥的女人| 在现免费观看毛片| 亚洲精品,欧美精品| 久久精品国产a三级三级三级| 国产男女内射视频| 国产探花极品一区二区| 欧美成人a在线观看| 午夜福利网站1000一区二区三区| 少妇熟女欧美另类| 99热国产这里只有精品6|