艾月霞,陳紅藝,李景鎮,吳慶陽,蔡 懿
深圳微納光子信息技術重點實驗室,深圳大學電子科學與技術學院,廣東深圳 518060
?
高速掃描攝影中光學偏轉加速技術研究
艾月霞,陳紅藝,李景鎮,吳慶陽,蔡懿
深圳微納光子信息技術重點實驗室,深圳大學電子科學與技術學院,廣東深圳 518060
摘要:分析并設計了一種新型的光學偏轉加速裝置,可以對入射光束偏轉角度進行倍數放大.該裝置利用曲面反射原理,當入射光束發生很小的原始偏轉時,其反射光束隨之發生偏轉且其偏轉角度被放大.可通過調節曲面反射鏡的曲率來實現微小光學偏轉角度放大1~2個數量級.該種技術主要用于非管掃描相機,比如轉鏡相機、電光晶體偏轉相機及其他光學掃描器件,無機械裝置,更適合小角度的電光偏轉以及古斯-漢欣位移等光學偏轉加速.
關鍵詞:掃描相機;電光偏轉;光學偏轉加速;高速攝影;古斯-漢欣位移;掃描器件
In the field of microsecond imaging, the interest is back to high speed rotating mirror cameras. To date, in fact, there has been no electronic camera yet that can match a rotating mirror camera with film, which possesses a bigger frame format of 102mm2order, more frame count than a hundred frames, higher spatial resolution, larger dynamic range of 103or more, and so on. Lai et al[1-2]have done the innovative and valuable researches on it. This kind of camera is predominantly used in the field of shock waves and detonation physics[3-5]. In the Shardin formula, optical information capacity which is the product of imaging frequency ν, spatial resolution N and the size of frame B in the time direction depends on the rotating mirror edge line-speed νpand the wavelength of light λ. Having considered the optical accelerating, the Shardin’s formula is perfected by
BNν=2βνp/λ
(1)
where β, the most important parameter in the optical accelerating circle, is an optical accelerating factor of 2~200 usually.
1Multi-reflection accelerating
The multi-reflection accelerating can multiply the deflection speed of the incident light-beam on the reflective surface of rotational mirror and can be divided into two schemes[6-9]: multi-reflection with wadge-gap-shaped retroreflector and multi-reflection with rotating polyhedron mirror. According to the law of reflection, the factor β for this kind of optical accelerating can be expressed by
β=2n
(2)
where n is the number of reflection on rotational reflecting surfaces of the wadge-gap-shaped retroreflector or the rotating polyhedron mirror. And the angular velocity Ω of the outgoing beam after reflecting can be written as Ω=2nω, where ω is the angular velocity of the retroreflector or the rotating polyhedron mirror.
The multi-reflection with wadge-gap-shaped retroreflector has especially promoted the rotating mirror streak camera with temporal resolution of nanosecond. As is shown in Fig.1[10], the deflection mode of galvanometer with the wedge-gap-shaped retroreflector is the combination of a rotational mirror and a stationary mirror, or two rotational mirrors with opposite directions. The streak camera prototype, based on this retroreflector, is an important breakthrough in the rotating mirror imaging field, and has a lot of excellent performances such as higher sensitivity, broader linear dynamic region, finer spatial contrast (a spatial resolution of 10 lp/mm), high temporal resolution (11.4 ns at 3.8 ns/pixel), larger information capacity and better adaptability, compared with the electronic camera, side-by-side testing.
Fig.1 Optical accelerating with wadge-gap-shaped retroreflector圖1 楔形縫隙回射器光學加速
The version of the galvanometer mentioned above, the wadge-gap-shaped retroreflector formed by a pair of rotating mirrors of two cones with opposite direction, is one of classical cameras and available in operation[11].
In this scheme, the number of reflection n, directly dominating the angular velocity of the outgoing beam which determines the optical information capacity for the framing imaging or the temporal resolution for streak imaging, is 16 for the double rotational mirrors with opposite direction and additional stationary folding mirror. The number of reflection n which is dependent upon the incident angle ψ of the imaging beam, the inclination δ between two deflecting mirrors, and the reflectivity of the mirrors, can be written by
n=2(ψ/δ+1)-1
(3)
Another multi-reflection with rotating polyhedron mirror has several models of combination of polyhedron mirrors with static mirrors to give birth to different accelerating factors. For example, as shown in Fig.2[11], the accelerator is composed of a rotating nine-sided mirror polyhedron 1, a collimating lens 2 and a triple prism 3, which is a typical arrangement with the optical accelerating factor β of 4 which means that as the polyhedron rotates by an angle of θ, the light beam rotates by an angle of 4θ.
Fig.2 Optical accelerating with combinations of polyhedron mirrors and stationary triple prism圖2 多面體鏡和三棱鏡復合光學加速
Both the multi-reflection with wadge-gap-shaped retroreflector and the multi-reflection with rotating polyhedron mirror, practically applied to the rotating mirror cameras, should meet two conditions. One condition is to be provided with a very exact rotating device, and the other one is to make the relative locations between the multiple reflecting light-beam and the reflective mirrors accurate. Therefore, the multi-reflection accelerating should be performed by accurately calculating and designing, and its device is complicated in structure and high in cost.
2Deflection amplification accelerating
The deflection amplification accelerating, different from that mentioned above and carried out by a curved surface mirror, is a new optical accelerating technique in which the small deflecting angle is to be amplified, continuously.
The key point of the accelerating is to mainly make the incident light-beam with tiny deflecting angles or tiny displacements sequentially be projected on different locations of a spatially curved surface to form different incident angles during the deflecting period. Based upon the law of reflection, the reflective angle and its incident angle are equal and continuously changing. The change range of the reflective angles is limited by the incident light-beam locations on the curved surface and the curvature of the curved surface which can both be designed according to requirements. Therefore, both scanning of the incident light-beam and amplifying deflection angles can be performed. The optical accelerating factor β is related to structural parameters, such as the relative location of the system configured for generating the original tiny deflections and displacements, and the curvatures of the curved surface.
As a rule, in this situation, the optical accelerating equation can be expressed by
(4)
where, as shown in Fig.3, φ is an original tiny deflection angle, γ is formed by the outgoing beam with the incident beam, Ω is the accelerated angular velocity and ω is the original angular velocity generated by an electro-optical deflector. Here, the optical accelerating factor β is around 2 to 200 usually. The optical information capacity of this kind of imaging technique which is now with advantage in the nanosecond and sub-nanosecond imaging field, can be increased by 1 to 2 orders of magnitude.
Fig.3 Schematic diagram of optical deflecting amplification accelerating圖3 光學偏轉加速示意圖
As shown in Fig.3, r is a radius of the cylindrical reflector and its curvature is ρ=1/r. Its normal crossesx-axis at point C. An incident angle at an incident point T is θ, thus its deflection angle relative to an incident optical axis is γ=2θ+φ, and θ=φ+α. Now the optical accelerating factor β can be deduced as follows
(5)
As shown, β is not a constant from Eq.(5) for this reflective mirror. When the original deflection angle φ is tiny,α and θ are small enough, β can be approximately written by
β=dγ/dφ=2ρL+1
(6)
where L is a distance between an original deflection point and a vertex of the cylindrical-surface reflective mirror. As it is seen from Eq.(6) , the optical accelerating factor is determined by ρ and L, and β is a constant in this supposed condition.
Now we can further study the optical accelerating factor β. As it is shown, β is not a constant from Eq.(5) for the cylindrical reflector. In general, if the reflective curved mirror is some transcendental curved cylindrical-surface, described by the following differential Eq.(7) , the optical accelerating factor could be a constant:
(7)
where the initial condition is (L,0). And as tan-1(y/x)~y/x, then Eq.(7) can be deduced to
(8)
The analytic solution of Eq.(8) is
x2-y2(β-1)/2=L2
(9)
As shown in Fig.4, the blue curve for the analytic solution of Eq.(9) is in very good agreement the black curve for the numeric solution of Eq.(7) near y=0 when β=50.
Fig.4 The analytic solution of Eq.(9) and the numeric solution of Eq.(7) (x-axis normalized by length L)圖4 方程(9)的解析解和方程(7)的數值解 (橫坐標軸長度L已歸一化處理)
According to Eq.(6), the optical accelerating factor β can be increased more if ρ increases. However, when ρ increases, the radius of the curved-surface reflective mirror will be decreased. Thus the curced-surface mirror is difficult to process and apply. Generally speaking, the light-beam deflection angle or the deflection speed can be improved by one to two orders of magnitude. In addition, no mechanical moving device is found in this accelerating device, such as the rotating polyhedron mirror and the retroreflector. Thus it is simple and more suitable for cooperating with the electro-optical deflection and the Goos-H?nchen displacement[12-13]to accelerate the light-beam deflection.
It is found that the deflection amplification accelerating can be used to improve the temporal resolution of the crystal-streak camera[14]20.0 ps to 2.5 ps[15]at least.
Conclusion
Two kinds of accelerating principle, mentioned above, are very useful and available in the ultra high speed rotating mirror cameras, framing and streak, and electro-optical deflecting recording devices. Both the multi-reflection accelerating and the deflecting amplification accelerating can effectively accelerate the deflecting speed of the incident light-beam for greatly increasing the optical information capacity. However, the former is complicated in structure and high in cost. The latter, different from the former, is a newly invented optical deflecting technique, in which the small deflecting angle can be amplified by one to two orders of magnitude. Its device, moreover, may have not any mechanical rotating parts, so it is simple and more suitable for cooperating with the electro-optical deflection and the Goos-H?nchen displacement to accelerate the light-beam deflection.As having simultaneously considered both the multi-reflection accelerating and the deflecting amplification accelerating, the optical accelerating factor β should be expressed by
β=2ndγ/dφ
(10)
On the understanding that n=16,dγ/dφ=16, which are reasonable and reliable, the factor β=512, which suggests an attractive prospect.
At last, the optical deflection accelerating techniques, upgrading the optical information capacity, can be applied to the ultra-high speed rotating polyhedron mirror devices and other scanning devices. Especially, the optical-deflection amplification accelerating, useful and available, may have a great perspective.
引文:艾月霞,陳紅藝,李景鎮,等. 高速掃描攝影中光學偏轉加速技術研究[J]. 深圳大學學報理工版,2016,33(2):134-137.(英文版)
References / 參考文獻:
[1] Lai C C, Goosman D R, Wade J T, et al. Design and field test of a galvanometer deflected streak camera[C]// The 25th International Congress on High Speed Photography and Photonics. Proceedings of SPIE. Beaune, Finland: SPIE, 2003, 4948:330-335.
[2] Frank A M, Bartolick J M. Solid state replacement of rotating mirror cameras[C]// The 27th International Congress on High Speed Photography and Photonics. Proceedings of SPIE. Xi’an, China: SPIE, 2007: 62791U-1-62791U-9.
[3] Held M. Simultaneously gained streak and framing records offer a great advantage in the field of detonics[J]. Propellants Explosives Pyrotechnics, 2001, 26(3): 148-155.
[4] Liang Lingliang, Tian Jinshou, Wang Tao, et al. Theotrtical and static experiment research on all optical solid state streak camera[J]. Acta Physica Sinica, 2014,63(6):060702-1-060702-7.(in Chinese)
梁玲亮, 田進壽, 汪韜, 等. 全光固體條紋相機的理論及其靜態實驗研究[J]. 物理學報, 2014,63(6): 060702-1-060702-7.
[5] Wang Feng, Wei Huiyue, Wei Xin, et al. Design and experimental research of all-optical scanning device[J]. High Power Laser and Particle Beams, 2013, 25(9):2213-2217.(in Chinese)
王峰,魏惠月,韋欣,等. 全光掃描裝置設計及實驗研究[J]. 強激光與粒子束, 2013, 25(9):2213-2217.
[6] Li Jingzhen. Time amplifying techniques towards atomic time resolution[J]. Science in China, 2009, 52(12): 3425-3446 .
[7] Li Jingzhen. Handbook of optics[M]. Xi’an: Shaanxi Science and Technology Press,2010:2195-2199.(in Chinese)
李景鎮. 光學手冊[M]. 西安:陜西科學技術出版社,2010:2195-2199.
[8] Liu Chunping,Li Shuang, Li Jingzhen, et al. A shutter pulse generator for high speed camera[J]. Journal of Shenzhen University Science and Engineering, 2013,30(2):133-137.(in Chinese)
劉春平,李爽,李景鎮. 一種用于高速攝影儀的快門脈沖發生器[J]. 深圳大學學報理工版,2013,30(2):133-137.
[9] Li Chunbo, Yu Chunhui, Li Jingzhen, et al. Structure design of rotating mirror based on the topology optimization theory for ultra-high speed camera[J]. Journal of Shenzhen University Science and Engineering, 2012, 29(4):304-310.(in Chinese)
李春波,余春暉,李景鎮,等. 基于拓?fù)淅碚摰某咚贁z影儀轉鏡結構設計[J]. 深圳大學學報理工版,2012, 29(4):304-310.
[10] Lai C C, A new tubeless nanosencond streak camera based on optical deflection and direct CCD imaging[C]// The 20th International Congress on High Speed Photography and Photonics. Proceedings of SPIE. Columbia, Canada: SPIE, 1992, 1801:454-469.
[11] Dubovik A S. The photographic recording of high-speed processes[M]. New York, USA: John Wiley, 1981:227-240.
[12] Liu Xuanbin, Cao Zhuangqi, Zhu Pengfei, et al. Simultaneously large and opposite lateral beam shifts for TE and TM modes on a double metal-cladding slab[J]. Chinese Physics Letters, 2006, 23(8): 2077-2079.
[13] Liu Xuanbin, Cao Zhuangqi, Zhu Pengfei, et al. Large positive and negative lateral optical beam shift in prism waveguide coupling system[J]. Physical Review E: Statistical Nonlinear & Soft Matter Physics, 2006, 73(5 Pt 2):88-101.
[14] Ireland C L M. A 20 ps resolution crystal streak camera[J]. Optics Communications, 1979,30(1): 99-103.
[15] Ai Yuexia, Li Jingzhen. Study on a new crystal streak camera with ~ 2.5 ps resolution[C]//The international Symposium on Photonics and Optoelectronics. Shanghai, China:IEEE,2012:580-582.
【中文責編:晨兮;英文責編:木南】
Optical-deflection accelerating techniques in streak camera
Ai Yuexia, Chen Hongyi?, Li Jingzhen, Wu Qingyang, and Cai Yi
Shenzhen Key Laboratory of Micro-Nano Photonic Information Technology, College of Electronic Science and Technology,Shenzhen University, Shenzhen 518060, Guangdong Province, P.R.China
Abstract:To get more precise high-speed streak cameras, we analyze a novel optical-deflection accelerating technique for light-beam. When the incident light-beam is deflected with a tiny initial deflection angle, according to the law of curved surface reflection, the reflective light-beam is deflected therewith and the deflection angle is enlarged. The deflecting amplification accelerating device can amplify the small deflecting angle by one to two orders of magnitude through adjust the curvature of the curved-surface. This device dominates the optical information capacity in tubeless streak camera, such as rotating mirror cameras, electro-optic crystal deflector cameras, and other light-beam scanning devices. Because there is no mechanical moving part in the new-developed device, this technique is suitable for cooperating with electro-optical deflection and the Goos-H?nchen displacement.
Key words:streak camera; electro-optic deflector; optical-deflection accelerating device; high-speed imaging; Goos-H?nchen displacement; scanning devices
作者簡介:艾月霞(1980—),女,深圳大學助理研究員. 研究方向:瞬態光電技術. E-mail:69116560@qq.com
基金項目:國家自然科學基金資助項目(61027014)
doi:CLC number: TN 312Document code: A10.3724/SP.J.1249.2016.02134
Received:2015-12-25;Accepted:2016-01-10
Foundation:National Natural Science Fundation of China (61027014)
? Corresponding author:Associate professor Chen Hongyi. E-mail: chenhy@szu.edu.cn
Citation:Ai Yuexia, Chen Hongyi, Li Jingzhen, et al. Optical-deflection accelerating techniques in streak camera[J]. Journal of Shenzhen University Science and Engineering, 2016, 33(2): 134-137.
【Optoelectronic Engineering / 光電工程】