• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Prediction of the Mooring Force of a 2-D Floating Oil Storage Tank

    2014-04-26 10:54:33CHUXinjieDONGShengandZHAOXizeng
    Journal of Ocean University of China 2014年6期

    CHU Xinjie, DONG Sheng, and ZHAO Xizeng

    1) College of Engineering, Ocean University of China, Qingdao 266100, P. R. China

    2) Drilling Technology Research Institute of Shengli Petroleum Engineering Corporation Limited, SINOPEC, Dongying 257017, P. R. China

    3) Ocean College, Zhejiang University, Hangzhou 310058, P. R. China

    Prediction of the Mooring Force of a 2-D Floating Oil Storage Tank

    CHU Xinjie1,2), DONG Sheng1),*, and ZHAO Xizeng3),*

    1) College of Engineering, Ocean University of China, Qingdao 266100, P. R. China

    2) Drilling Technology Research Institute of Shengli Petroleum Engineering Corporation Limited, SINOPEC, Dongying 257017, P. R. China

    3) Ocean College, Zhejiang University, Hangzhou 310058, P. R. China

    A Constrained Interpolation Profile (CIP)-based model is developed to predict the mooring force of a two-dimensional floating oil storage tank under wave conditions, which is validated against to a newly performed experiment. In the experiment, a box-shaped floating oil storage apparatus is used. Computations are performed by an improved CIP-based Cartesian grid model, in which the THINC/SW scheme (THINC: tangent of hyperbola for interface capturing; SW: Slope Weighting), is used for interface capturing. A multiphase flow solver is adopted to treat the water-air-body interactions. The Immersed Boundary Method (IBM) is implemented to treat the body surface. Main attention is paid to the sum force of mooring line and velocity field around the body. It is found that the sum force of the mooring line increases with increasing wave amplitude. The body suffers from water wave impact and large body motions occur near the free surface. The vortex occurs near the sharp edge, i.e., the sharp bottom corners of the floating oil storage tank and the vortex shedding can be captured by the present numerical model. The present model could be further improved by including turbulence model which is currently under development. Comparison between the computational mooring forces and the measured mooring forces is presented with a reasonable agreement. The developed numerical model can predict the mooring line forces very well.

    floating oil storage; mooring line force; CIP method; numerical method; Immersed Boundary Method

    1 Introduction

    Marine oil spills will lead to ecological disasters. It causes serious concerns for the marine life and ecological environment, especially in the coastal area. It is necessary to make quick response to this kind of marine accident. An alternative way is to choose floating oil storage tanks, which is the best way to maximise oil storage capacity when dealing with an offshore oil spill.

    Offshore structures have been widely used in many areas of engineering, such as ships, platforms, wind turbines, oil productions and temporary storage of recovered liquids. So far, most of the offshore structures have been limited to fixed platforms in shallow-water areas. In deeper water, floating structures may be more feasible. However, the design of floating structures to survive extreme events is more complicated than that with fixed platforms. It requires knowledge and methods to treat complex problems of fluid-structure interactions in severe seas with large wave-induced motions and distorted free surface. Therefore, it is important to carry out an integrated analysis for floating structures. However, thus far only limited studies have been performed (Greco et al., 2009; Hong et al., 2004; Koo and Kim, 2005). In the present study, a Computational Fluid Dynamics (CFD) model is developed for the coupled dynamic analysis of an offshore floating oil storage tank in waves.

    To model interactions between floating structures and environmental conditions, numerical models have been well developed based on linear and nonlinear theories. The model based on linear theory is sufficient for routine design in which the motions of the fluid and/or structure body are small. In many cases, the nonlinear-theory based model has to be used when considering flow with extremely distorted free surface and/or body responses with large amplitudes. Models based on nonlinear theory are usually divided into two groups: the potential theory model and the Navier-Stokes (NS) model (Ma and Yan, 2009). The major difficulty in numerical simulation is that the topology of free surface may be largely distorted or broken up, which makes it impossible to apply the conventional model such as potential flow model. Therefore, the NS-based model, instead of the Laplace model, should be preferred when considering violent wave-body interactions. The NS-based models are further classified into mesh method (FDM: Finite difference method, FVM: Finite volume method and FEM; Finite element method, etc.) and meshless method (SPH: Smoothed Particle Hy-drodynamics; MPS: Moving-particle semi-implicit method; PFEM: Particle Finite Element Method, etc.) according to the discretization approaches. The NS-based method is usually called CFD method. CFD methods are developing fast in many areas of engineering, widely used as one of the powerful tools to resolve complicated offshore engineering problems and prevent offshore disasters. The advantage of the numerical study is the low cost, the ease to re-build the experiments and the ability to provide detailed information on the hydrodynamics of fluid- structure interactions, not suffering from the scaling problems present in physical models. Great progress has been made on meshless methods in recent years. However, fewer studies on interaction between wave and floating structure have been performed because the computational efficiency and accuracy is still a big problem for meshless method (Vandamme et al., 2011).

    FDM is the oldest one and still widely used in CFD at present. In computational fluid dynamics, using an upwind differencing technique for the advection term in Navier-Stokes equations is necessary for a stable numerical calculation. The use of upwind scheme introduces excessive numerical diffusion and associated inaccuracies because it only uses grid point values to approximate a function profile. Great efforts to reduce such numerical diffusion have resulted in many high order upwind schemes, e.g., QUICK, TVD, etc. About 27 years ago, CIP emerged as a high order upwind scheme (Takewaki et al., 1985). In the CIP method, a cubic polynomial is used to approximate the value of a function within a grid cell. It uses the grid point values and its spatial derivatives in two grid points to form a cubic polynomial to approximate the profile (Yabe et al., 2001). The CIP method has been used not only for convection problems but also for free surface/interface capturing calculation, but suffers from low accuracy and mass non-conservative (Hu and Kashiwagi, 2004, 2009). To improve the accuracy through relatively simple implementation, several free surface/interface capturing schemes have been proposed. Xiao et al. (2005) developed a THINC scheme similar to the CIP method. It uses a smoothed Heaviside function as characteristic function instead of a cubic polynomial and is derived from a conservative form of advection equation. As a result, it shows better performance and conservativeness of mass than previous schemes (Zhao, 2011). Yokoi (2007) proposed the WLIC (Weighed Line Interface Calculation) scheme to improve the VOF-type methods, like the original VOF method, THINC scheme and so on. It works by simple weighting procedure and dimension splitting for simple implementation. Xiao et al. (2011) revisited the THINC scheme and proposed the THINC/SW scheme. In the THINC/SW method, a variable steepness parameter is adopted instead of the constant steepness parameter in the original THINC scheme, which helps maintain the thickness of the jump transition layer. In the present study, the THINC/SW scheme is adopted for the free surface/interface capturing calculations.

    The objective of the present paper is to predict the mooring line force of the floating oil storage tank due to regular waves. Here a multi-phase flow model, which solves the flow associated with the air, water and solid simultaneously, has been developed for modeling wave and floating body interactions. In the following, we introduce briefly the numerical implementations for the governing equations and the free surface representations. The improved interface capturing method, THINC/SW method, is outlined. Then, the experimental set-up is presented. Finally, the computational results are presented about the interaction between regular waves and a floating oil storage tank. Main attention is paid to the mooring line force and flow velocity around the floating oil tank. The numerical results are compared with experimental data. The article ends with some general conclusions.

    2 Governing Equations

    The computations are performed by means of a CIP-based model (Hu and Kashiwagi, 2004, 2009; Zhao and Hu, 2012) for predicting strongly nonlinear wave-structure interactions. The method is based on the solution of the Navier-Stokes equations with the Constrained Interpolation Profile (CIP) adopted as the basic numerical scheme to obtain a robust flow solver in a Cartesian grid, where the THINC/SW scheme is used for free surface/ interface capturing; an immersed boundary method is used for wave-structure interaction treatment (Peskin, 1972).

    To solve the wave-body interactions, we consider a two-dimensional viscous and incompressible flow. The governing continuity equations and Navier-Stokes equations are:

    where viscous stress is expressed by

    In the above equations, p is hydrodynamic pressure, ui(i=1, 2) are the velocity components along xithe axes, t is time; ρ and μ are the water density and viscosity, respectively. The third term on the right of Eq. (2) is the external force, including the gravitational force. The numerical model considers the fluid-body interaction as a multiphase problem involving water, air and structure. A major advantage of a multi-phase model is that the boundary conditions for the velocities at the free surface, which have a large influence on the robustness and accuracy of the method, are not needed anymore. A fixed Cartesian grid that covers the whole computation domain is used. We use a volume fraction fieldmφ(m=1, 2, and 3 indicate water, air and solid, respectively) to represent and trackthe interface. The total volume function for water and body is solved by using the following advection equation:

    where, φ13=φ1+φ3. We assume that the density and viscosity of the solid phase are the same as those of a liquid phase to ensure stability. This set of our CFD code is different from most other existing CFD models. The volume function for solid body φ3is determined by a Lagrangian method in which a rigid body is assumed. The position of water is calculated by φ1=φ13-φ3, where the position of liquid and solid phase φ13is captured by a VOF-typed free surface/interface capturing method. The volume function for air φ2is then determined by φ2= 1.0-φ1-φ3. After all volume functions have been calculated, the physical property λ, such as the density and viscosity, are calculated by the following formula:

    The drawback of the averaging process is that the computational accuracy is reduced to the first order in terms of cell size at the interfaces. More details can be found in Zhao (2011) and Zhao and Hu (2012).

    3 Numerical Methods

    3.1 Fractional Step Method

    Following Zhao and Hu (2012), the governing equations are discretized using a high-order finite difference method on a Cartesian grid system. A staggered grid configuration is used to discretize the dependent variables. In each cell, the pressure p is computed at the cell center, the velocity component v is computed at the middle of the horizontal edge, and the velocity component u is computed at the middle of the vertical edge. A fractional step scheme is used to solve the N-S equations. The numerical solution of the governing equations is divided into three steps: one advection phase and two non-advection phases. In the advection phase the spatial derivatives of the velocities are needed to apply the CIP method for this phase. In the first non-advection phase, the terms of diffusion and external forces are solved by explicit method and renewed intermediate velocities are obtained. In the final phase, the velocities are updated and coupled with pressure field (Zhao and Hu, 2012).

    3.2 CIP Method

    In the advection step, the calculation is done by the CIP scheme. The basic idea of the CIP method is to reconstruct the profile of a variable advected by flows by using not only the variable itself, but also its spatial gradient g=?f/?x:

    In the CIP method, the profile of a variable is considered as a cubic polynomial between two grid points, xiand xi-1. For simplicity we assume a constant advection velocity. Then Eq. (7) has the same form as Eq. (6). For the case of u> 0 we may approximate a profile for fninside the upwind cell [xi-1, xi] as

    From the obtained profile of the position xiand n-th time step, the profile at the time step n+1 is obtained by shifting the profile with -uΔt, i.e., the time evolution of the function f and g can be obtained by using the following Lagrangian invariants:

    The two unknown coefficients in Eq. (8) can be determined by using known quantities. It is not difficult to obtain

    For the two-dimensional CIP method, the polynomial below was used by Yabe and Wang (1991):

    The ten coefficients of the above polynomial are determined from four known physical values at grid points and six derivative values at the cell corners. Detailed coefficients of the polynomial for 2D case can be found in Hu and Kashiwagi (2004).

    3.3 Free Surface Treatment

    In a physical problem the gas-liquid interface (free surface) is with zero thickness. However, when we solve the density function of liquid1φ by Eq. (4), we obtain a free surface with finite thickness, i.e., a smeared interface due to numerical diffusion associated with the finite difference scheme. To avoid this, we use an accurate interface capturing scheme, the THINC/SW scheme (Xiao et al., 2011) to calculate the free surface. The THINC/SW scheme is also a VOF type method (Hirt and Nichols, 1981). In the THINC/SW method, a variable steepness parameter is adopted instead of the constant steepness parameter used in the original THINC scheme, which helps maintain the thickness of the jump transition layer. A 1-D THINC scheme is described in the following. Multi-dimensional computations are performed by a directional splitting method.

    The one-dimensional advection equation for a density function φ can be written in conservation form

    Eq. (12) is descretized by a finite volume method. For a known velocity field un, integrating Eq. (12) over a computational cell [xi-1/2, xi+1/2] and a time interval [tn, tn+1], we have

    gi±1/2is the flux across the cell boundary (x=xi±1/2), and φ is the cell-averaged density function defined at the cell center (x=xi). The fluxes are calculated by a semi-Lagrangian method. Similar to the CIP method, the profile of φ inside an upwind computation cell is approximated by an interpolation function. Instead of using a polynomial in the CIP scheme, the THINC scheme uses a hyperbolic tangent function in order to avoid numerical smearing and oscillation at the interface. Since 0≤ χ ≤ 1, and the variation of χ across the free surface is step-like, a piecewise modified hyperbolic tangent function is used to approximate the profile inside a computation cell, which is shown as follows:

    where α, γ, δ and β are parameters to be specified. α and γ are parameters used to avoid interface smearing as given by

    Parameter δ is used to determine the middle point of the hyperbolic tangent function, and is calculated by solving the following equation:

    Parameter β is used to control the sharpness of the variation of the color function. In the original THINC scheme, a constant β=3.5 is usually used, which may result in ruffling the interface which aligns nearly in the direction of the velocity (Xiao et al., 2011). Therefore, a refined THINC scheme, the THINC/SW, by determining adaptively according to the orientation of the interface is proposed by Xiao et al. (2011).

    In the two-dimensional case, parameters β could be determined by the following equations:

    where n=(nx, ny) is the unit norm vector of the interface.

    After χi(x) is determined, the flux at the cell boundary can be calculated by Eq. (14). In Fig.1, gt+1/2is indicated by the dashed area for ui+1/2>0. After all of the fluxes across the cell boundaries have been computed, the cellintegrated value at the new time step can be obtained by Eq. (13). This cell-integrated value is used to determine the free surface position; therefore, mass conservation is automatically satisfied for the liquid.

    Fig.1 Concept of the THINC/SW scheme.

    A validation test, known as Zalesak’s problem (Zalesak, 1979), is performed with the THINC/SW scheme and the original THINC scheme. The two cases with different grid sizes are addressed. This test is one of the most popular scalar advection tests. A velocity field is given by u=(y-0.5, 0.5-x) with Δt=2π/628. One revolution is completed in 628 time steps. Numerical error is defined as

    Table 1 Errors for Zalesak’s test problem

    Fig.2 Numerical results of Zalesak’s problem after one rotation.

    3.4 Body Surface Treatment

    For simplicity, calculations are performed for a rigid body. To accurately predict the body position, the hydrodynamic force acting on the body is needed. It can be obtained as follows:

    where nkis the k-th component of the outward unit normal vector.

    Comparing to Eq. (2), we have added a forcing term in Eq. (19). Since in the present numerical solution procedure, the method of imposing the velocity distribution inside and on the body boundary is equivalent to adding a forcing term to the momentum equation, an alternative way is to do the following updating after the velocity-pressure calculation:

    In a boundary cell Eq. (20) is a volume fraction weighting treatment for velocity interpolation. The idea for the treatment of the fluid-structure interaction is derived from an immersed boundary method (Peskin, 1972).

    4 Experimental Setup

    The experiment was carried out in a two-dimensional wave tank at Drilling Technology Research Institute, Shengli Petroleum Administrative Bureau, China. The glass-walled flume is 62 m long, 1.5 m wide and 2.0 m high, with a still water depth of 0.75 m. It is equipped with a piston-type wave generator at one end and a wave absorbing device at the other. The photo of the wave flume is shown in Fig.3 and a photo of the floating oil storage tank is shown in Fig.4. Table 2 gives the size of the body. In Fig.4, the solid rectangle body on the left is used in the present paper for initial purpose. The floating oil storage tank is anchored to the bottom of the wave flume with four rope mooring lines aligned vertically. Four strain gauges are used to measure the line strainforce. Fig.5 shows the photo of the strain gauge. Main attention is paid to the sum strain force. In the next section, the predicted strain sum force is compared with the measured data. The dynamics of the body at any instantaneous position is shown in Fig.6.

    Fig.3 The physical wave flume.

    Fig.4 Physical model of the oil storage tank.

    Table 2 Main parameter of the body model

    Fig.5 The strain gauge.

    In this study, the floating oil storage tank is moored with fibre rope mooring lines aligned vertically as shown in Fig.6. Three different line lengths are chosen as L=0.25 m, 0.50 m and 0.70 m. We will illustrate the instantaneous position of the floating body during its interaction with incoming waves theoretically. Before get the instantaneous position of the body, we should know the force acting on the body. An assumption is made that there is no slack state in the mooring lines during its work time. This also means that only sway and heave displacements of the body are considered, with no rotational motion of the body occurring. Based on the above considerations, the dynamics of the floating oil storage tank is calculated using the following equations:

    where m is the mass of the body, axand aythe horizontal and vertical accelerations of the body, respectively. ΣFxand ΣFyare the resultant horizontal and vertical forces acting on the body, respectively. ΣMcx, ΣMcyand ΣMcTrepresent the summation of moment by the forces acting on the body in the x and y-directions and the mooring line tensile forces, respectively. Also, referring to Fig.6, considering no slack state, the geometry of the mooring line gives the following equation:

    There are four unknown parameters ax, az, and the offshore and onshore side mooring strain forces T1and T2in the above four equations (Eqs. (21–24)). The hydrodynamic forces P1, P2, P3and P4, as shown in Fig.6, are obtained numerically by surface integration of the water pressure around the floating body as shown in Eq. (18). By solving Eqs. (21–24), the unknown parameters ax, az, T1and T2can be obtained. After that, it is not difficult to update the body position at new time step using equations of motion.

    Fig.6 Instantaneous position of the floating body during its interaction with wave.

    5 Results

    In this section, numerical prediction of the mooring line forces with waves acting on the floating oil storage tank is carried out for three different mooring line lengths. Our main interest is the sum of the mooring line forces. Numerical results are compared with experimental measurements for each case.

    Cases were carried out using a different numerical wave tank from the physical flume with the floating body center placed at x= 6 m, as shown in Fig.7. Several simplified set-ups were installed in order to save CPU time. Waves were generated by prescribing an inflow velocity similar to a piston-like wavemaker, where the real wavemaker motion is not necessary. A smaller numerical tank (12.3 m) than the physical flume (62.0 m) was used with a damping zone at the end of the wave tank.

    In the computation, a stationary Cartesian grid was employed with grid numbers of 515(x)×196(y), 515(x) ×220(y) and 515(x)×172(y) for three different mooring line lengths of L=0.25 m, L=0.5 m and L=0.7 m. The minimum grid spacing was Δx=Δy=0.003 m around the body and the free surface. The time step was dynamically determined to satisfy the criterion of a CFL number of 0.1 and the total simulation time up to 25 s. Detailed information about the effect of both the grid spacing and time step can be found in Zhao et al. (2010). Wave period Twwas chosen to be 1.0 s for regular waves. Input wave amplitude of A=0.02 m and 0.03 m were chosen for the input wave conditions.

    Fig.7 Initial set-up of the floating oil storage tank in the numerical model.

    Fig.8 shows the computed sum force of the mooring lines for the cases of L=0.25 m A=0.02 m and A=0.03 m. The time series of the free-surface elevation measured in the experiment are also shown for comparison in Fig.8. We can notice that for the case of A=0.02 m the sum force of the mooring line shows linear response to the regular wave. The numerical results show reasonable agreement with the measurements. For the case of A=0.03 m, discrepancy can be found between the numerical results and the experimental data. The reason for this can be that the floating body shows nonlinear response to the increased wave amplitude. Look closely, the main trend of the sum force of the mooring line can be predicted using this model. It can be noted that the sum force of the mooring line increases with increasing wave amplitude.

    The comparison of the sum force of the mooring line between the calculated results and the experimental data is presented in Fig.9 for the case of mooring line length L=0.5 m and amplitude A=0.3 m. For this case, the numerical results agree well with the experimental data. Comparing with Fig.9(a), it can be noted that the sum force of the mooring line is a little larger. The reason for this may be the effect of the free surface. For the case of L=0.5 m, the floating body is closer to the free surface than in the case of L=0.25 m.

    Fig.10 presents the comparison of the sum force of the mooring line between the calculated results and the experimentally measured values for the case of mooring line length L=0.7 m. The input wave amplitude is set to be 0.02 m. As the weight of the floating body is almost the same as the buoyancy force acting on it, there acts no initial tensile force on each mooring line under the still water condition. It can be noted that there has occurred slack state in the mooring line and as a result there is impulsive forces acting on it. However, the numerical result represents well the measured data. From above comparisons, it can be concluded that the proposed numerical method is effective to predict the sum forces acting on the mooring lines.

    Fig.8 Sum force of mooring lines with mooring line length L=0.25 m: (a) A=0.02 m; (b) A=0.03 m.

    Fig.9 Sum force of mooring lines with mooring line length L=0.5 m A=0.03 m.

    Fig.10 Sum force of mooring lines with mooring line length L=0.7 m, A=0.02 m.

    The time series of numerical results of the sway motion of the oil storage are also presented in Fig.11. Results for two mooring line lengths L=0.5 m and L =0.7 m are presented in Figs.9(a) and (b), respectively. The positive sway represents the offshoreward horizontal displacement of the floating oil storage, i.e., along the direction of positive x-axis. On the other hand, the negative sway represents the onshoreward horizontal displacement of the floating oil storage, which is along the direction of negative x-axis. We can find that the sway motion is much smaller than the mooring line length. The heave motion is too small and not presented here. For the case of L= 0.5 m, A=0.02 m, the body suffers linear response to the regular waves. The averaged magnitudes of sway displacement of the body are seen zero. As for the case of L=0.5 m and A= 0.03 m, the averaged magnitudes of sway displacement of the body are seen nonzero. The average value increases in the positive direction. It can be also noted that the amplitude of the body sway motion increases with the increasing input wave amplitude. For the case of L=0.7 m, the body shows nonlinear response and oscillates about its positive position. It can be explained by the slack state of the mooring line. For this case, the magnitude of the body sway motion is about 5 times as large as the case of L= 0.5 m. We can conclude that the body suffers from the water wave impact near the free surface.

    In order to illustrate the details of the flow-body interaction, velocity-vector corresponding to a typical case of oscillation t (17 s – 18 s) is shown here. Fig.12 illustrates the numerical simulation of the water particle velocity field around the moored floating oil storage tank along the channel length for different stages of a wave cycle. The corresponding wave height and wave period are 0.03 m and 1.0 s, respectively. The mooring line length L=0.5 m is used here. The results for t=17.0 s and t=17.1 s reveal that the progressive wave collides with the right return flow from the left face of the oil storage tank and the direction of the water particle velocity changes from horizontally to downward. Also, a vortex appears under the left side bottom corner face of the breakwater at t=17.2 s and t=17.3 s, which disappears at t=17.5 s. It again appears under the left side bottom corner of the oil storage tank at t=17.7 s and at t=17.8 s, respectively. It has been shown that the vortex occurs near the sharp edge, i.e., the sharp bottom corners of the floating oil storage tank and the vortex shedding can be captured by the present numerical model.

    Fig.11 Time series values of the simulated sway motion of floating oil tank: (a) L=0.5 m; (b) L=0.7 m.

    6 Conclusions

    Fig.12 Numerical results of water particle velocity (m s-1) field around the floating oil storage (L=0.5 m, A=0.03 m).

    In this study, interaction between regular wave and a 2-D floating oil storage tank is investigated by a Constrained Interpolation Profile (CIP)-based model. The computational results are validated by comparing with those of a newly performed experiment. In the experiment, a box-shaped floating oil storage tank is used. Computations are performed by an enhanced CIP-based Cartesian grid method based on the solution of the Navier-Stokes equations with the CIP method adopted as the basic numerical scheme to obtain a robust flow solver. A multi-phase flow solver is adopted to treat the water-air-body interactions. An Immersed Boundary method is introduced to couple them together. A more accurate and mass conservative VOF-typed scheme, the THINC/SW scheme, is used for interface capturing. A benchmark problem, known as Zalesak’s problem, is addressed by comparing the THINC/SW scheme with the original THINC scheme. It is found that the accuracy of THINC/SW scheme is higher than that of the original THINC scheme. Studies of interaction between the 2-D floating oil storage tank and regular wave are carried out considering different wave amplitudes and mooring line lengths. Main attention is paid to the sum force of mooring line and velocity field around the body. It is found that the sum force of the mooring line increases with increasing wave amplitude and the body suffers from the water wave impact and the large body motions near the free surface. The vortex occurs near the sharp edge, i.e., the sharp bottom corners of the floating oil storage tank and the vortex shedding can be captured by the present numerical model. The present model could be further improved by including turbulence model which is currently under development.

    Acknowledgements

    The study is supported by the National Natural Science Foundation of China (51209184, 51279186, 51479175).

    Greco, M., Colicchio, G., and Faltinsen, O. M., 2009. Bottom slamming for a very large floating structure: Coupled global and slamming analyses. Journal of Fluids and Structures, 25 (2): 420-430.

    Hirt, C. W., and Nichols, B. D., 1981. Volume of Fluid (VOF) method for the dynamics of free boundaries. Journal of Computational Physics, 39 (1): 201-225.

    Hong, D. C., Hong, S. Y., and Hong, S. W., 2004. Numerical study of the motions and drift force of a floating OWC device. Ocean Engineering, 31 (2): 139-164.

    Hu, C. H., and Kashiwagi, M., 2004. A CIP-based method for numerical simulations of violent free surface flows. Journal of Marine Science and Technology, 9 (4): 143-157.

    Hu, C. H., and Kashiwagi, M., 2009. Two-dimensional numerical simulation and experiment on strongly nonlinear wavebody interactions. Journal of Marine Science and Technology,

    14 (2): 200-213.

    Koo, B. J., and Kim, M. H., 2005. Hydrodynamic interactions and relative motions of two floating platforms with mooring lines in side-by-side offloading operation. Applied Ocean Research, 27 (6): 292-310.

    Ma, Q. W., and Yan, S., 2009. QALE-FEM for numerical modeling of non-linear interaction between 3D moored floating bodies and steep waves. International Journal for Numerical Methods in Engineering, 78 (6): 713-75.

    Peskin, C. S., 1972. Flow patterns around heart valves: A numerical study. Journal of Computational Physics, 10 (2): 252-271.

    Takewaki, A., Nishiguchi, A., and Yabe, T., 1985. Cubic interpolated Pseudo-particle method (CIP) for solving hyperbolictype equations. Journal of Computational Physics, 61 (2): 261-268.

    Vandamme, J., Zou, Q., and Reeve, D., 2011. Modeling floating object entry and exit using Smoothed Particle Hydrodynamics. Journal of Waterway, Port, Coastal, and Ocean Engineering, 137 (5): 213-224.

    Xiao, F., Honma, Y., and Kono, T., 2005. A simple algebraic interface capturing scheme using hyperbolic tangent function. International Journal for Numerical Methods in Fluids, 48 (9): 1023-1040.

    Xiao, F., Satoshi, I., and Chen, C. G., 2011. Revisit to the THINC scheme: A simple algebraic VOF algorithm. Journal of Computational Physics, 230 (19): 7089-7092.

    Yabe, T., and Wang, P. Y., 1991. Unified numerical procedure for compressible and incompressible fluid. Journal of the Physical Society of Japan, 60 (7): 2105-2108.

    Yabe, T., Xiao, F., and Utsumi, T., 2001. The constrained interpolation profile method for multiphase analysis. Journal of Computational Physics, 169 (2): 556-593.

    Yokoi, K., 2007. Efficient implementation of THINC scheme: A simple and practical smoothed VOF algorithm. Journal of Computational Physics, 226 (2): 1985-2002.

    Zalesak, S. T., 1979. Fully multi-dimensional flux-corrected transport algorithm for fluid flow. Journal of Computational physics, 31 (3): 335-362.

    Zhao, X. Z., 2011. Validation of a CIP-based tank for numerical simulation of free surface flows. Acta Mechanica Sinica, 27 (6): 877-890.

    Zhao, X. Z., and Hu, C. H., 2012. Numerical and experimental study on a 2-D floating body under extreme wave conditions. Applied Ocean Research, 35 (1): 1-13.

    Zhao, X. Z., Hu, C. H., and Sun, Z. C., 2010. Numerical simulation of focused wave generation using CIP method. In: The Proceedings of the Twentieth International Offshore and Polar Engineering Conference. Beijing, 596-603.

    (Edited by Xie Jun)

    (Received March 17, 2013; revised March 29, 2013; accepted August 30, 2013)

    ? Ocean University of China, Science Press and Springer-Verlag Berlin Heidelberg 2014

    * Corresponding authors. E-mail: dongsh@ouc.edu.cn;

    xizengzhao@zju.edu.cn

    netflix在线观看网站| 亚洲成人精品中文字幕电影| 天堂√8在线中文| 午夜福利在线观看吧| 国产区一区二久久| 亚洲在线自拍视频| 欧美日韩黄片免| 国产主播在线观看一区二区| 岛国在线免费视频观看| 三级毛片av免费| 欧美最黄视频在线播放免费| 亚洲色图av天堂| 12—13女人毛片做爰片一| 国产私拍福利视频在线观看| 91国产中文字幕| 伦理电影免费视频| 成人特级黄色片久久久久久久| av欧美777| 黄色视频,在线免费观看| 1024手机看黄色片| 国产av麻豆久久久久久久| 欧美日韩黄片免| 岛国视频午夜一区免费看| 中亚洲国语对白在线视频| 成熟少妇高潮喷水视频| 国产精品1区2区在线观看.| 日韩 欧美 亚洲 中文字幕| 国内毛片毛片毛片毛片毛片| av片东京热男人的天堂| 一本综合久久免费| 丁香欧美五月| a级毛片在线看网站| 亚洲男人的天堂狠狠| 少妇熟女aⅴ在线视频| 欧美日本亚洲视频在线播放| а√天堂www在线а√下载| av片东京热男人的天堂| 欧美性长视频在线观看| 亚洲成人中文字幕在线播放| 母亲3免费完整高清在线观看| 精品久久蜜臀av无| 婷婷精品国产亚洲av| 亚洲国产看品久久| 国产精品久久视频播放| 91大片在线观看| 精品少妇一区二区三区视频日本电影| 免费高清视频大片| 久久久国产成人免费| 黄色a级毛片大全视频| 亚洲熟女毛片儿| 久久天堂一区二区三区四区| 香蕉国产在线看| 午夜久久久久精精品| av免费在线观看网站| av欧美777| 啪啪无遮挡十八禁网站| 欧洲精品卡2卡3卡4卡5卡区| 亚洲熟女毛片儿| 久久中文看片网| 1024视频免费在线观看| xxx96com| 97碰自拍视频| 亚洲av日韩精品久久久久久密| 在线观看免费午夜福利视频| 黄色毛片三级朝国网站| av中文乱码字幕在线| 亚洲av日韩精品久久久久久密| а√天堂www在线а√下载| 日韩欧美在线乱码| 成人高潮视频无遮挡免费网站| 国产视频一区二区在线看| 久久久久亚洲av毛片大全| 十八禁网站免费在线| 色播亚洲综合网| 欧美中文日本在线观看视频| 午夜精品一区二区三区免费看| 色老头精品视频在线观看| av福利片在线观看| 亚洲精品在线美女| 亚洲真实伦在线观看| 久久久水蜜桃国产精品网| 一本久久中文字幕| 亚洲国产精品久久男人天堂| 757午夜福利合集在线观看| 2021天堂中文幕一二区在线观| videosex国产| 免费看十八禁软件| 免费在线观看亚洲国产| 免费观看精品视频网站| 不卡av一区二区三区| 18禁观看日本| 黄色 视频免费看| 丰满人妻一区二区三区视频av | 午夜福利视频1000在线观看| 免费在线观看成人毛片| xxxwww97欧美| 久久久久久久久免费视频了| 国产精品一区二区精品视频观看| 白带黄色成豆腐渣| 人妻夜夜爽99麻豆av| 三级国产精品欧美在线观看 | 亚洲精品中文字幕在线视频| 欧美日本亚洲视频在线播放| 欧美3d第一页| 国产成人精品久久二区二区91| 日韩有码中文字幕| 制服人妻中文乱码| 欧美精品啪啪一区二区三区| 免费在线观看影片大全网站| 成人特级黄色片久久久久久久| 国产午夜福利久久久久久| 久久精品夜夜夜夜夜久久蜜豆 | x7x7x7水蜜桃| 久久热在线av| 老熟妇乱子伦视频在线观看| 大型黄色视频在线免费观看| 午夜免费观看网址| 极品教师在线免费播放| 国产成人av教育| 可以在线观看毛片的网站| 三级男女做爰猛烈吃奶摸视频| 欧美一区二区精品小视频在线| 99re在线观看精品视频| 女生性感内裤真人,穿戴方法视频| 99国产综合亚洲精品| 精品一区二区三区四区五区乱码| 精品高清国产在线一区| 国产精品1区2区在线观看.| 草草在线视频免费看| 亚洲一码二码三码区别大吗| 91麻豆av在线| 搡老熟女国产l中国老女人| 99国产极品粉嫩在线观看| 国产精品久久久人人做人人爽| 变态另类丝袜制服| 一进一出抽搐动态| 国产精品电影一区二区三区| 成人特级黄色片久久久久久久| 亚洲成人精品中文字幕电影| 欧美一区二区国产精品久久精品 | 级片在线观看| 午夜激情av网站| 久久精品夜夜夜夜夜久久蜜豆 | 狂野欧美白嫩少妇大欣赏| 亚洲国产中文字幕在线视频| 亚洲在线自拍视频| 午夜久久久久精精品| 久久久久国产精品人妻aⅴ院| 国产三级中文精品| 十八禁人妻一区二区| 99热这里只有精品一区 | www.www免费av| 久久精品国产99精品国产亚洲性色| 国产av麻豆久久久久久久| 国产99白浆流出| 久久欧美精品欧美久久欧美| 国产主播在线观看一区二区| 国产亚洲精品久久久久5区| 桃红色精品国产亚洲av| 好男人在线观看高清免费视频| 精品国内亚洲2022精品成人| 亚洲午夜精品一区,二区,三区| 久久欧美精品欧美久久欧美| 麻豆国产97在线/欧美 | 非洲黑人性xxxx精品又粗又长| 国产成人精品久久二区二区免费| av中文乱码字幕在线| 1024香蕉在线观看| 丝袜人妻中文字幕| 性欧美人与动物交配| 女人爽到高潮嗷嗷叫在线视频| 国产精品一区二区三区四区免费观看 | 欧美一级毛片孕妇| 国产激情偷乱视频一区二区| 亚洲熟女毛片儿| 国产私拍福利视频在线观看| 久久性视频一级片| 午夜激情福利司机影院| 成人18禁高潮啪啪吃奶动态图| 亚洲精品一卡2卡三卡4卡5卡| 国产亚洲精品第一综合不卡| 99在线人妻在线中文字幕| 99riav亚洲国产免费| 国产激情久久老熟女| 久久久久国产精品人妻aⅴ院| 国产爱豆传媒在线观看 | 校园春色视频在线观看| 国产熟女xx| 国产av在哪里看| 久久久久久大精品| 久9热在线精品视频| 精品一区二区三区av网在线观看| 欧美日韩瑟瑟在线播放| 成人国产一区最新在线观看| 亚洲片人在线观看| 最近最新中文字幕大全免费视频| 久久久久国产一级毛片高清牌| 色老头精品视频在线观看| 啦啦啦免费观看视频1| 免费看美女性在线毛片视频| 国产真实乱freesex| 国产精品久久久久久精品电影| 一级片免费观看大全| 国产片内射在线| 熟女电影av网| 国产欧美日韩一区二区三| 又大又爽又粗| 久久伊人香网站| 欧美日韩瑟瑟在线播放| 色综合亚洲欧美另类图片| 午夜亚洲福利在线播放| av片东京热男人的天堂| 91在线观看av| 日本五十路高清| 亚洲九九香蕉| 狂野欧美激情性xxxx| www.熟女人妻精品国产| 午夜精品一区二区三区免费看| 变态另类成人亚洲欧美熟女| 国产精品影院久久| 国产精品精品国产色婷婷| 1024手机看黄色片| 成人精品一区二区免费| 男人舔女人的私密视频| 欧美性猛交╳xxx乱大交人| 精品欧美一区二区三区在线| 搞女人的毛片| 国产真人三级小视频在线观看| 日韩大码丰满熟妇| 最新美女视频免费是黄的| 久久久久国产精品人妻aⅴ院| 亚洲男人天堂网一区| 一本久久中文字幕| 久久国产精品人妻蜜桃| 老汉色∧v一级毛片| 长腿黑丝高跟| 十八禁人妻一区二区| 麻豆一二三区av精品| 免费在线观看影片大全网站| 欧美性猛交╳xxx乱大交人| 色尼玛亚洲综合影院| av免费在线观看网站| 国产蜜桃级精品一区二区三区| 日韩有码中文字幕| 曰老女人黄片| 99热只有精品国产| aaaaa片日本免费| 亚洲成av人片在线播放无| 日韩 欧美 亚洲 中文字幕| 精品欧美国产一区二区三| 老司机深夜福利视频在线观看| 在线永久观看黄色视频| 操出白浆在线播放| 99国产精品一区二区三区| 黄片小视频在线播放| bbb黄色大片| 激情在线观看视频在线高清| 男人舔女人下体高潮全视频| a级毛片在线看网站| 国产探花在线观看一区二区| 麻豆久久精品国产亚洲av| 国产主播在线观看一区二区| 国产黄色小视频在线观看| 国产成人一区二区三区免费视频网站| 99国产精品99久久久久| 午夜影院日韩av| 国产高清有码在线观看视频 | 国产熟女xx| 丁香欧美五月| 欧美黑人巨大hd| √禁漫天堂资源中文www| 中文亚洲av片在线观看爽| 哪里可以看免费的av片| 欧美日韩一级在线毛片| 真人做人爱边吃奶动态| 日本五十路高清| 岛国在线免费视频观看| 欧美大码av| 一区二区三区高清视频在线| 亚洲无线在线观看| 91大片在线观看| 亚洲国产看品久久| 特大巨黑吊av在线直播| 国产野战对白在线观看| xxxwww97欧美| 精品人妻1区二区| 欧美成狂野欧美在线观看| 亚洲av五月六月丁香网| 18禁美女被吸乳视频| 免费一级毛片在线播放高清视频| 国产欧美日韩精品亚洲av| 黄色丝袜av网址大全| 巨乳人妻的诱惑在线观看| 精品无人区乱码1区二区| 999久久久精品免费观看国产| 亚洲精华国产精华精| 亚洲国产日韩欧美精品在线观看 | 国产精品亚洲一级av第二区| 国产主播在线观看一区二区| 1024视频免费在线观看| 国产激情偷乱视频一区二区| 日韩精品青青久久久久久| 成人午夜高清在线视频| 成年女人毛片免费观看观看9| 不卡av一区二区三区| 精品人妻1区二区| 精品免费久久久久久久清纯| 法律面前人人平等表现在哪些方面| 亚洲专区国产一区二区| 中文字幕人妻丝袜一区二区| 免费在线观看黄色视频的| 韩国av一区二区三区四区| av中文乱码字幕在线| 日韩av在线大香蕉| 欧美久久黑人一区二区| 99久久久亚洲精品蜜臀av| 国产精品精品国产色婷婷| √禁漫天堂资源中文www| 国产午夜福利久久久久久| 听说在线观看完整版免费高清| 国产精品永久免费网站| 男人舔奶头视频| 国产熟女午夜一区二区三区| 国产视频一区二区在线看| 母亲3免费完整高清在线观看| 天天一区二区日本电影三级| 亚洲av第一区精品v没综合| 99久久99久久久精品蜜桃| 天堂动漫精品| 一级毛片女人18水好多| 国产高清视频在线观看网站| 日韩大尺度精品在线看网址| 国产av不卡久久| 99热这里只有是精品50| 国产精品一区二区三区四区久久| 一本精品99久久精品77| 久久精品夜夜夜夜夜久久蜜豆 | 麻豆久久精品国产亚洲av| 男插女下体视频免费在线播放| 国产精品1区2区在线观看.| 人成视频在线观看免费观看| 亚洲午夜精品一区,二区,三区| 性色av乱码一区二区三区2| 搡老熟女国产l中国老女人| 一个人免费在线观看的高清视频| 五月玫瑰六月丁香| 丰满人妻熟妇乱又伦精品不卡| 日韩 欧美 亚洲 中文字幕| 中出人妻视频一区二区| 天天躁狠狠躁夜夜躁狠狠躁| www国产在线视频色| 国产野战对白在线观看| 久久精品国产99精品国产亚洲性色| 2021天堂中文幕一二区在线观| 非洲黑人性xxxx精品又粗又长| 日韩免费av在线播放| 久9热在线精品视频| 黄色 视频免费看| 国产欧美日韩一区二区精品| 天天躁夜夜躁狠狠躁躁| 久久久久性生活片| 久久人人精品亚洲av| 免费在线观看成人毛片| 天天躁狠狠躁夜夜躁狠狠躁| 成人三级做爰电影| av欧美777| 亚洲男人的天堂狠狠| 一区福利在线观看| 亚洲国产中文字幕在线视频| 精品国产美女av久久久久小说| 亚洲精品国产一区二区精华液| 国产又色又爽无遮挡免费看| 99热这里只有精品一区 | 长腿黑丝高跟| 男男h啪啪无遮挡| 久久香蕉国产精品| 欧美日本视频| 精品免费久久久久久久清纯| 精品福利观看| 久久久久国内视频| 欧美三级亚洲精品| 欧美日韩福利视频一区二区| 波多野结衣高清无吗| 无人区码免费观看不卡| 人人妻人人澡欧美一区二区| 成年女人毛片免费观看观看9| 巨乳人妻的诱惑在线观看| 老司机福利观看| 国产一区在线观看成人免费| 法律面前人人平等表现在哪些方面| 久久精品国产亚洲av香蕉五月| 法律面前人人平等表现在哪些方面| 婷婷六月久久综合丁香| 欧美大码av| 男女床上黄色一级片免费看| 久久 成人 亚洲| 露出奶头的视频| 国产亚洲精品一区二区www| 久久中文字幕一级| 亚洲av五月六月丁香网| 高清毛片免费观看视频网站| 少妇粗大呻吟视频| 97超级碰碰碰精品色视频在线观看| 亚洲自拍偷在线| 精品久久蜜臀av无| 少妇被粗大的猛进出69影院| 欧美一级a爱片免费观看看 | 国语自产精品视频在线第100页| 中亚洲国语对白在线视频| 日本成人三级电影网站| 国产熟女午夜一区二区三区| 人人妻,人人澡人人爽秒播| 最新在线观看一区二区三区| av在线播放免费不卡| 高清在线国产一区| 亚洲精品美女久久av网站| 国产激情欧美一区二区| 久久中文字幕一级| 国产精品99久久99久久久不卡| 国产精品久久视频播放| 老汉色∧v一级毛片| 狂野欧美白嫩少妇大欣赏| 午夜福利在线在线| 中出人妻视频一区二区| 久久精品国产清高在天天线| 怎么达到女性高潮| av在线天堂中文字幕| 日韩国内少妇激情av| 99国产精品一区二区蜜桃av| 一区二区三区激情视频| 免费在线观看黄色视频的| 免费看a级黄色片| 中出人妻视频一区二区| 1024香蕉在线观看| 天堂av国产一区二区熟女人妻 | 日日爽夜夜爽网站| 免费看美女性在线毛片视频| 国产精品98久久久久久宅男小说| 成年人黄色毛片网站| 伊人久久大香线蕉亚洲五| 99久久精品国产亚洲精品| 人人妻人人看人人澡| 亚洲狠狠婷婷综合久久图片| 激情在线观看视频在线高清| 给我免费播放毛片高清在线观看| 亚洲专区中文字幕在线| 成年女人毛片免费观看观看9| 男女做爰动态图高潮gif福利片| 国产在线精品亚洲第一网站| 久久久久久久午夜电影| 欧美绝顶高潮抽搐喷水| 日韩大码丰满熟妇| 嫩草影视91久久| 国产69精品久久久久777片 | 午夜免费激情av| 国产精品综合久久久久久久免费| 欧美丝袜亚洲另类 | 久久久久久久精品吃奶| 久久精品91蜜桃| 99久久国产精品久久久| 欧美在线黄色| 国产又黄又爽又无遮挡在线| 亚洲中文av在线| 一本大道久久a久久精品| 老鸭窝网址在线观看| 日韩中文字幕欧美一区二区| 午夜激情福利司机影院| 国内揄拍国产精品人妻在线| 看免费av毛片| 一个人免费在线观看电影 | 国产真人三级小视频在线观看| 首页视频小说图片口味搜索| av中文乱码字幕在线| 好男人在线观看高清免费视频| 又黄又爽又免费观看的视频| 亚洲熟妇中文字幕五十中出| 亚洲在线自拍视频| 亚洲精品美女久久久久99蜜臀| 精品日产1卡2卡| 2021天堂中文幕一二区在线观| e午夜精品久久久久久久| 色在线成人网| 可以免费在线观看a视频的电影网站| 亚洲自拍偷在线| 欧美黄色淫秽网站| 亚洲自拍偷在线| 日本撒尿小便嘘嘘汇集6| 91字幕亚洲| 国产av又大| 欧美精品亚洲一区二区| 久久精品国产亚洲av高清一级| 久久精品国产综合久久久| 亚洲精品美女久久av网站| xxx96com| 免费av毛片视频| 亚洲国产中文字幕在线视频| 日韩 欧美 亚洲 中文字幕| 成年免费大片在线观看| 久久久久久人人人人人| 制服诱惑二区| 亚洲国产高清在线一区二区三| 免费搜索国产男女视频| 欧美日韩瑟瑟在线播放| 亚洲精品中文字幕一二三四区| 真人做人爱边吃奶动态| 久久精品影院6| 人妻丰满熟妇av一区二区三区| 免费av毛片视频| 国产av一区在线观看免费| 日韩欧美一区二区三区在线观看| 熟女少妇亚洲综合色aaa.| 88av欧美| 免费在线观看视频国产中文字幕亚洲| 毛片女人毛片| 国产成人系列免费观看| 午夜精品一区二区三区免费看| 少妇裸体淫交视频免费看高清 | 亚洲国产欧美人成| 亚洲av五月六月丁香网| 可以在线观看的亚洲视频| 国产不卡一卡二| 欧美最黄视频在线播放免费| 亚洲av熟女| 每晚都被弄得嗷嗷叫到高潮| 久久久久国产一级毛片高清牌| 99精品欧美一区二区三区四区| 国产精品亚洲美女久久久| 一本久久中文字幕| 亚洲成人精品中文字幕电影| 91老司机精品| 亚洲欧美一区二区三区黑人| 妹子高潮喷水视频| 亚洲第一欧美日韩一区二区三区| 亚洲国产欧洲综合997久久,| 欧美精品啪啪一区二区三区| 国产真实乱freesex| 国产不卡一卡二| 国产激情欧美一区二区| 夜夜爽天天搞| 国产精品久久久久久亚洲av鲁大| 99国产综合亚洲精品| 精品少妇一区二区三区视频日本电影| 亚洲欧美激情综合另类| 黄片小视频在线播放| 成人永久免费在线观看视频| 制服诱惑二区| 在线观看一区二区三区| 99国产精品99久久久久| 久久精品成人免费网站| av中文乱码字幕在线| 亚洲精品国产一区二区精华液| 19禁男女啪啪无遮挡网站| 白带黄色成豆腐渣| 美女 人体艺术 gogo| 国产欧美日韩一区二区三| 国产熟女xx| 毛片女人毛片| 中文字幕人成人乱码亚洲影| 欧美一级a爱片免费观看看 | 黄色 视频免费看| 校园春色视频在线观看| 欧美性猛交黑人性爽| 国产精品一区二区精品视频观看| 久久久久性生活片| 88av欧美| 日韩精品中文字幕看吧| 一本一本综合久久| 色噜噜av男人的天堂激情| 精品久久久久久久人妻蜜臀av| 麻豆av在线久日| 亚洲乱码一区二区免费版| 黄色a级毛片大全视频| 亚洲av熟女| 嫩草影视91久久| 最新美女视频免费是黄的| 男女之事视频高清在线观看| ponron亚洲| 色尼玛亚洲综合影院| 俄罗斯特黄特色一大片| 999精品在线视频| 国产精品久久电影中文字幕| 国产精品爽爽va在线观看网站| 婷婷亚洲欧美| 精品无人区乱码1区二区| 亚洲,欧美精品.| 国产午夜精品论理片| 真人一进一出gif抽搐免费| av欧美777| 欧美日本视频| 精品欧美国产一区二区三| 久久精品aⅴ一区二区三区四区| 亚洲av片天天在线观看| 两性夫妻黄色片| 国内揄拍国产精品人妻在线| 欧美日本视频| 99在线视频只有这里精品首页| 男女做爰动态图高潮gif福利片| 女人爽到高潮嗷嗷叫在线视频| 麻豆国产av国片精品| 99久久精品热视频| 无限看片的www在线观看| 欧美日韩福利视频一区二区| 欧美午夜高清在线| 日本熟妇午夜| 国产成人一区二区三区免费视频网站| 久久久久久久久久黄片| 少妇熟女aⅴ在线视频| 中文字幕精品亚洲无线码一区| 岛国视频午夜一区免费看| 老熟妇乱子伦视频在线观看| 97超级碰碰碰精品色视频在线观看| 天堂√8在线中文| 在线观看免费视频日本深夜| 婷婷丁香在线五月| 90打野战视频偷拍视频|