• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    3D Numerical Study on Compound Heat Transfer Enhancement of Converging-diverging Tubes Equipped with Twin Twisted Tapes*

    2012-02-14 08:25:38HONGYuxiang洪宇翔DENGXianhe鄧先和andZHANGLianshan張連山
    關鍵詞:連山

    HONG Yuxiang (洪宇翔)**, DENG Xianhe (鄧先和) and ZHANG Lianshan (張連山)

    Key Lab of Enhanced Heat Transfer and Energy Conservation of Ministry of Education, School of Chemistry and Chemical Engineering, South China University of Technology, Guangzhou 510640, China

    1 INTRODUCTION

    Heat transfer enhancement technology plays an important role in chemical industry, power engineering, air conditioning and many other industries, especially in the applications of energy saving and waste heat recovery. In general, according to whether external power is needed, the techniques for heat transfer enhancement can be divided into two categories [1].One is the active strengthening technology, which needs extra external power sources, for example, electrostatic fields, surface vibration and jet impingement,etc. The other is the passive strengthening technology,which needs no direct use of external power. Due to its less energy consumption, easier operation and higher reliability, the passive strengthening technologies, such as wall roughness (converging-diverging tube, grooved tube and corrugated tube, etc.), additives, surface coatings and swirl flow inducement(twisted tape, snail entrance and helical screw tape,etc.), are used more widely.

    Compared to a plain tube, converging-diverging tube (CD) imparts turbulence to the near wall flow which thins the boundary layer and enhances heat transfer. The geometry of a CD sketched in Fig. 1 is characterized by the pitch length (P), converging to diverging pitch ratio (δ=P1/P2) and rib height (e). Li[2] reported experimental data for two bare convergingdiverging tubes with δ=8.4︰5 and 5︰8.4 at e=0.8 mm and P=13.4 mm. He found that both Nu and f for CD with δ=8.4︰5 were higher than that for δ=5︰8.4, and the case with δ=8.4︰5 performed better overall thermal performance than that with δ=5︰8.4.Chen et al. [3] further analyzed the heat transfer enhancement mechanism of the CD by a 2D numerical simulation. Their results show that the synergy between the temperature gradient and velocity vector near the wall is one of the main parameters to control heat transfer in fully developed turbulent flow. Insertion of twisted tape is one of the effective measures to enhance heat transfer rate by creating swirling flows,mixing fluid between the mainstream zone and the near wall zone. Because of its low cost and easy manufacture, the twisted tape has been widely employed to produce compact heat exchangers and to upgrade the old heat exchangers over the past few years. Manglik and Bergles [4, 5] concluded that the tube partitioning and flow blockage, longer flow path and tape induced secondary fluid circulation were mainly the reasons for heat transfer enhancement by using the twisted tape in the plain tube. Saha et al. [6, 7]have experimentally investigated the heat transfer and friction factor characteristics of water in a plain tube equipped with regularly spaced twisted tapes in laminar and turbulent flow. It was found that the regularly spaced twisted tapes performed better than the full-length twisted tapes in laminar flow, while the variation tended to be opposite in turbulent flow. Abu-Khader [8]conducted an industrial study to investigate the effect of twist ratio and tube diameter on heat transfer coefficient and friction factor of a tube fitted with twisted tapes. It was found that the twisted tapes performed better in laminar flow than in turbulent flow, and the twist ratio had a clear effect on Nusselt number at the smaller tube diameter. Wang et al. [9] numerically revealed that the structural parameters had an important effect on the thermal performance of the tube fitted with regularly spaced twisted tapes in turbulent flow,and the thermal enhancement factor could be greater than 1.0 by the geometric optimization.

    As mentioned above, although twisted tape families perform better in laminar flow than in turbulent flow, turbulent flow is more common than laminar flow in industrial heat exchangers. Therefore, many attempts have been made to enhance turbulent thermal performance by using geometrically modified twisted tapes. For example, counter/co-swirling twin twisted tapes [10], serrated twisted tapes [11], broken twisted tapes [12], center-cleared twisted tapes [13] and squarecut twisted tapes [14] were invented to seek better overall thermal performance in turbulent flow. However, most of the twisted tapes mentioned above are very inconvenient in manufacture, leading to high costs for industry applications. Fortunately, counter-swirling twin twisted tapes [10] are a good alternative to obtain better thermal performance, since it is just modified by placing two identical counter-swirl full-length twisted tapes in the tube side, which can be easily realized in tube and shell heat exchangers, but it can’t further improve heat transfer rate.

    Aiming at compact heat exchanger design and further improving heat transfer rate as much as possible, technology of compound heat transfer enhancement simultaneously utilizing two or more heat transfer enhancement devices has increasingly attracted more and more attentions. Zimparov [15, 16] carried out a series of experiments on heat transfer and flow characteristics for corrugated tubes fitted with twisted tapes, and found that this combination leads to superimposed heat transfer enhancement compared with the bare plain tube. In other recent studies, a number of compound heat transfer enhancement devices such as micro-finned tube fitted with left-right inserts [17],plain tubes fitted with twisted tapes and wire coils [18, 19]and spirally grooved tubes fitted with twisted tapes [20]etc. have been developed to take full advantage of synergistic effect resulted from two heat transfer enhancement devices.

    From the foregoing, it is interesting to evaluate the potential of an effective compound technology with a promising geometry for heat transfer enhancement. However, to the authors’ knowledge, little attention has been focused on the turbulent heat transfer and flow behaviors in converging-diverging tubes equipped with twin twisted tapes (CDT). Despite that many studies were implemented on CDs, no sufficient knowledge about the flow mechanism and relevant correlations was available. Hence, the heat transfer and flow characteristics of bare CDs are investigated firstly, and then the synergy effect of the CD combined with the twin twisted tapes is performed to evaluate the further heat transfer enhancement over bare CDs.The motivation behind the present work is to enhance heat transfer by taking full advantage of transversal vortices generated from CDs and longitudinal vortices generated from twin twisted tapes. The effects of a series of geometry parameters are investigated.

    2 NUMERICAL SIMULATION PROCEDURE

    2.1 Physical models

    Figure 1 Structure and layout of CDTs

    Table 1 Structure parameters for the present study

    The present studied geometries and descriptions of CDTs are shown in Fig. 1 and Table 1, respectively.The bare CDs are investigated for comparison, with the identical geometric parameters to that of CDTs.The twin counter-swirling twisted tapes with twist ratio ofy=L/ware placed in the tube passageway. The length and thickness of the twisted tapes areL=22.5 mm andc=0.8 mm, respectively. A gap distance of 0.5 mm between tapes and CDs is manufactured to consider convenient practical application of assembling and disassembling. The width of twisted tape isw=(d-2e-1-b)/2. The adjacent two twisted tapes are in counter-swirl direction and the angle between them is the same. The angle between two adjacent tapes isα=360/n. The effect of different tube pitch length (P),pitch ratio (δ=P1︰P2), rib height (e), gap distance between twisted tapes (b) and tape number (n) as listed in Table 1, will be investigated in this work.

    2.2 CFD data reduction

    The CFD data is reduced in the following procedure. Firstly, the total heat transfer rate in the tube can be obtained by

    whereTwis the average wall temperature, andTbis the average bulk temperature.

    The Nusselt number can be calculated as

    Finally, the thermal enhancement factor (η) for evaluating overall thermal performance of the enhanced tubes at the constant pumping power can be determined by [21]

    2.3 Governing equations and boundary conditions

    The problem in this paper is three-dimensional,incompressible, turbulent and steady flow, and the following assumptions or conditions are made to obtain the governing equations: (1) Heat conduction of twisted tapes and natural convection in the tube are neglected; (2) The thickness of tube wall is assumed to be zero; (3) The physical properties of working fluid water is constant.

    The governing differential equations in the Cartesian tensor notation used to describe the fluid flow and heat transfer in this paper can be written in the following forms:

    Continuity equation:

    Momentum equation:

    where

    Energy equation:

    The Renormalization-group (RNG)k-εturbulence model developed by Yakhot and Orszag [22] is used in the present numerical simulation:

    wherekis the fluid turbulent kinetic energy,εis the dissipation rate of turbulent kinetic energy,Gkrepresents the generation of turbulent kinetic energy due to the mean velocity gradients,μeffis the effective viscosity as defined byμeff=μ+μt=μ+ρCμk2/ε, and the constants in the model are known asCμ=0.0845,C1ε=1.42,C2ε=1.68,αk=αε=1.393.

    No slip condition is applied on tube wall and twisted tapes. Uniform heat flux conditions are imposed on the tube wall. The twisted tapes were set as non-conductive to heat. At the computational domain of inlet and outlet, periodical fully developed condition is imposed, which indicates that the velocity,pressure and temperature gradient repeat themselves in domain as follows:

    whereuis the velocity, Δpis the local pressure drop,Θis the temperature gradient,ris the position vector andLis the periodic length vector. The fluid inlet temperature is 303 K. The Reynolds numbers varies from 10000 to 20000.

    2.4 Grid generation and numerical method

    The grid generations and numerical simulations are performed using commercial CFD software package Gambit 2.2.30 and Fluent 6.3.26, respectively.Fig. 2 presents the mesh generation of the computation domain using hybrid method of size function and boundary layer technique. Tetrahedral grid and hexahedron grid are employed to generate mesh in the interior of tube and boundary layers, respectively. In all cases, the grid is finer close to the wall and the vicinity of the twisted tapes where the temperature and velocity gradients are large. Grid independence tests of three different grid numbers (363375, 552687 and 727861) for CDT withP=11.25 mm,e=0.5 mm,δ=8︰1 andb=0.5 mm atRe=10000-20000 are shown in Fig. 3. It is found that up to 1.17% and 0.94% differences of the Nusselt number (Nu) and friction factor (f) respectively exist between the coarsest mesh and the second finer mesh, and less than 0.15% and 0.83% deviations exist between the two finer meshes, which indicate the middle mesh with grid number of 552687 is suitable for getting a gridindependent solution. Therefore, this grid is adopted in the subsequent simulation with the compromise of computational time and solution precision.

    Figure 2 Meshes generation of the CDTs

    Figure 3 Grid independence tests for different grid number■ 363375-Nu; ● 552687-Nu; 727861-Nu; □ 363375-f;○ 552687-f; 727861-f

    In the present study, the differential governing equations are solved with the finite volume method, using pressure based solver with double precision. For the convective and diffusive terms a QUICK discretization scheme is employed while the SIMPLEC algorithm is used for the pressure-velocity coupling. The solution convergence is achieved by a criterion of the residuals below 10-5for continuity and 10-6for other equations.

    2.5 Validation using the published correlations

    To check the model validity, as presented in Fig. 4,a plain tube model is first validated with the classical Gnielinski equation and Petukhov equation [23], and a model of a plain tube fitted with twin counter- swirling twisted tapes (PT,L=22.5 mm,w=8.75 mm,y=2.57,c=0.8 mm) with the similar geometric parameters is also confirmed with the experimental equations obtained by Eiamsa-ardet al. [10]. The deviation of the plain tube between numerical results and classical empirical equations forNuandfare ±4.61%and ±2.26%, respectively. The numerical results of PT are compared with the Eiamsa-ard equations with the discrepancy of less than ±15.24% forNuand ±11.83%forf. By taking into account the Eiamsa-ard equations agreeing with the experimental data within ±10% and±6% forNuandf, respectively, the present numerical and experimental results are considered in satisfactory agreement in engineering for reasonable accuracy,especially due to the comparative nature and the optimization purposes of the current investigation. The error is mainly from the constant physical properties assumption and the model intrinsic error.

    Figure 4 Verifications of the numerical results of the plain tube and PT● plain tube-Nu-numerical; ○ plain tube-f-numerical;plain tube-Nu-Gnielinski; plain tube-f-Petukhow;▲ PT-Nu-numerical; △ PT-f-numerical; ▼ PT-Nu-Eiamsa-ard;▽ PT-f-Eiamsa-ard

    3 RESULTS AND DISCUSSION

    The numerical analysis of heat and fluid-flows through the CDs and the CDTs will be discussed below,respectively. In the following text, the situation of variable geometric parameters is labeled with an abbreviation.For example, the label “CDT-11.25-0.5-8︰1-b(4.5)”means that the tube pitch length is 11.25 mm, rib height of 0.5 mm, pitch ratio of 8︰1 and the gap between twisted tapes is 4.5 mm for the CDT. The tape number isn=2 unless otherwise stated.

    3.1 Heat transfer and flow characteristics for CDs

    Figures 5 and 6 show the effect of tube pitch ratio(δ) and rib height (e) on Nusselt number (Nu) and friction factor (f) for CDs with different tube pitch length (P=11.25 mm, 22.5 mm), respectively. In addition, the thermal enhancement factors of the CDs are presented in Fig. 7. From these figures, some general tendencies can be drawn. First, the Nusselt number increases and the friction factor decreases as the Reynolds number increases. Second, the thermal enhancement factors of all CDs are greater than 1 and decrease with the increasingRefor most cases, except for CDs withP=22.5 mm,e=0.5 mm andδ=1︰8 or 5︰4.

    Figure 5 Variations of (a) Nusselt number and (b) friction factor versus Reynolds number for CDs with different P(11.25,22.5 mm) and δ (1︰8, 5︰4, 8︰1) at fixed e (0.5 mm)○ plain tube; □ CD-22.5-1︰8; ■ CD-11.25-1︰8; △ CD-22.5-5︰4; ▲ CD-11.25-5︰4; ▽ CD-22.5-8︰1; ▼ CD-11.25-8︰1

    3.1.1Effect of pitch ratio

    It is shown in Fig. 5 that the pitch ratio has a strong effect on both Nusselt number and friction factor. As indicated in Fig. 5 (a), at the same pitch length,one can see that the cases ofδ=8︰1 has the largest Nusselt number, the next is the cases ofδ=1︰8, and then the cases ofδ=5︰4. It is noted that there is only a tiny difference of the Nusselt number between the cases ofδ=1︰8 and 5︰4. Meanwhile, it is observed from Fig. 5 (b) that the friction factor decreases as the pitch ratio increases from 1︰8 to 5︰4 and increases as the pitch ratio increases from 5︰4 to 8︰1. As illustrated in Fig. 7 (a), the thermal enhancement factor increases as the pitch ratio increases from 1︰8 to 8︰1 at the same pitch length, which indicates that the longer the converging pitch is, the better the overall thermal performance.

    3.1.2Effect of tube pitch

    Figure 6 Variations of (a) Nusselt number and (b) friction factor versus Reynolds number for CDs with different P(11.25,22.5 mm) and e (0.5, 0.8, 1.1 mm) at fixed δ (8︰1)○ plain tube; □ CD-22.5-0.5; ■ CD-11.25-0.5; △ CD-22.5-0.8; ▲ CD-11.25-0.8; ▽ CD-22.5-1.1; ▼ CD-11.25-1.1

    Figure 7 Variations of η versus Reynolds number for (a) CDs with different P (11.25, 22.5 mm) and δ (1︰8, 5︰4, 8︰1) at fixed e (0.5 mm) and (b) CDs with different P (11.25, 22.5 mm) and e (0.5, 0.8, 1.1 mm) at fixed δ (8︰1)

    Figure 8 Contour plots of velocity and streamlines for CD-22.5-0.5-5︰4 and CD-11.25-0.8-8︰1 at Re=10000

    It is seen from Figs. 5, 6 that the higher Nusselt number and friction factor are obtained for the cases withP=11.25 mm, due to high turbulence intensity imparted to the flow between two ribs, while the lower ones are gained for the cases withP=22.5 mm.The increases in Nusselt number and friction factor forP=11.25 mm are in range of 10.8%-25.9% and 36%-74% aboveP=22.5 mm. Moreover, it can be observed from Fig. 7 that the shorter the tube pitch length is, the better the thermal enhancement factor becomes, except for the case ofP=11.25 mm,e=0.5 mm andδ=1︰8.

    3.1.3Effect of rib height

    Rib height is an important factor of rough surfaces using protrusions mounted on them to get heat transfer enhancement. A suitable rib height with appropriate pressure drop is in favor of improving the thermal enhancement factor. It is seen that from Fig. 6 that both Nusselt number and friction factor increase with increasing rib height in all cases. This is because,by increasing rib height, the local heat transfer near the wall is improved because the turbulence intensity induced by ribs is intensified. One can see from Fig. 7(b) that the cases ofe=0.5 mm have the best thermal enhancement factor at most of the Reynolds number withη=1.38-1.59, the next is the cases ofe=0.8 mm withη=1.34-1.59, and then the cases ofe=1.1 mm withη=1.23-1.48. Meanwhile, the cases withP=11.25 mm yield a better thermal performance than the cases withP=22.5 mm at the same rib height.

    3.1.4Flow structure

    Contour plots of velocity and streamlines for CD-22.5-0.5-5︰4 and CD-11.25-0.8-8︰1 atRe=10000 onY=0 mm plane are displayed in Fig. 8. It can be visible from Fig. 8 (a) that due to the variation of the tube cross section, the velocity increases in the converging sections and decreases in the diverging sections. Meanwhile, the pressure decreases in the converging sections and increases in the diverging sections, according to the Bernoulli equation [24].Hence, the converging section is more contributive than the diverging section to the benefit of heat transfer enhancement with the promoted flow turbulence.As seen in Fig. 8 (b), owing to the direction of fluid flow changing abruptly under the effect of the axial pressure gradient in the near wall zone, a pair of transverse vortices is generated because of flow separation in the diverging section and effectively employed in the converging section to thin the boundary layer and improve turbulence. Consequently, the CDs give higher heat transfer rate than that of the plain tube.

    Figure 9 Contour plots of turbulence intensity for plain tube and CDs with different geometric parameters at Re=10000

    Figure 10 Variations of (a) Nusselt number and (b) friction factor versus Reynolds number for CDTs with different P(11.25, 22.5 mm ) and different δ (1︰8, 5︰4, 8︰1) at fixed e (0.5 mm) and b (0.5 mm)○ plain tube; □ CDT-22.5-0.5-1︰8; ● PT; △ CDT-22.5-0.5-5︰4; ■ CDT-11.25-0.5-1︰8; ▽ CDT-22.5-0.5-8︰1;▲ CDT-11.25-0.5-5︰4; ▼ CDT-11.25-0.5-8︰1

    Contour plots of turbulence intensity onY=0 mm plane are displayed in Fig. 9 for CDs with different geometric parameters, atRe=10000. It demonstrates that the CDs can effectively enhance the turbulence intensity in the near wall zone but can’t further improve the turbulence intensity in the mainstream. In addition, higher turbulence intensity is seen in the converging sections rather than the diverging sections,which is the reason why the CDs with the longer converging pitch show higher heat transfer rate. A larger turbulence intensity zone is found in the cases with higher rib, resulting in higher heat transfer rate and larger pressure drop.

    As discussed above, when bare CDs are employed, it is concluded that the Nusselt number and friction factor of CDs are higher than that of the plain tube at around 44.4%-167.6% and 34.7%-511.6%,respectively. Moreover, the thermal enhancement factors for CDs with varying geometric parameters are in range of 1.23-1.59.

    3.2 Heat transfer and flow characteristics for CDTs

    Figures 10 and 11 illustrate the effects of tube pitch ratio (δ), rib height (e) and gap distance between twisted tapes (b) on variations of Nusselt number and friction factorversusReynolds number for CDTs withP=11.25 mm and 22.5 mm, respectively. Except for the cases of “CDT-11.25-0.5-8︰1-b(4.5)” and“CDT-11.25-0.5-8︰1-b(8.5)”, the gap distance between twisted tapes for all other cases isb=0.5 mm unless otherwise stated. Twisted tape with a smaller twist ratio has a better thermal performance than the one with a bigger twist ratio [10], so the twist ratio for all cases withb=0.5 mm approximates toy=2.5. A plain tube fitted with twin twisted tapes (PT) is also presented for comparisons. The thermal enhancement factors for the CDTs are presented in Fig. 12. In the figures, it is clearly seen that the thermal enhancement factor of all CDTs are greater than 1 but smaller than their counterparts of CDs, and the thermal enhancement factor decreases with increasing Reynolds number for most cases, except for some cases withe=0.5 mm at low Reynolds number.

    Figure 11 Variations of (a) Nusselt number and (b) friction factor versus Reynolds number for CDTs with different P(11.25, 22.5 mm ), different e (0.5, 0.8, 1.1 mm) and different b (0.5, 4.5, 8.5 mm) at fixed pitch ratio δ (8︰1)○ plain tube; □ CDT-22.5-0.5; ● PT; △ CDT-22.5-0.8; ■ CDT-11.25-0.5; ▽ CDT-22.5-1.1; ▲ CDT-11.25-0.8; ★ CDT-11.25-0.5-b(4.5);▼ CDT-11.25-1.1; ◆ CDT-11.25-0.5-b(8.5)

    Figure 12 Variations of η versus Reynolds number for (a) CDTs with different P (11.25, 22.5mm ) and different δ (1︰8, 5︰4,8︰1) at fixed e (0.5 mm) and b (0.5 mm); (b) CDTs with different P (11.25, 22.5 mm ), different e (0.5, 0.8, 1.1 mm) and different b (0.5, 4.5, 8.5 mm) at fixed pitch ratio δ (8︰1)

    3.2.1Effect of pitch ratio

    It is clearly seen from Fig. 10, at bothP=11.25 and 22.5 mm, the cases withδ=8︰1 have the largest Nusselt number than those withδ=5︰4 and 1︰8. AtP=22.5 mm, it is presented in Fig. 10 (a) that the Nusselt number of the cases withδ=5︰4 and 1︰8 almost equal to that of the PT. The reason is that the CDTs have rib structures compared with the PT, leading to a narrower width of twisted tape. Then, the heat transfer reduction resulting from the narrower twisted tape counteracts the heat transfer enhancement of the rib effect. Whereas, due to the increase of pitch number, atP=11.25 mm, one can see from Fig. 10 (a) that the cases withδ=5︰4 and 1︰8 have larger Nusselt number than the PT. As shown in Fig. 10 (b), at the same pitch length, the cases ofδ=8︰1 have the largest friction factor, the next is the cases ofδ=1︰8,and then is the cases ofδ=5︰4, and the last is the PT.As illustrated in Fig. 12 (a), whenP=22.5 mm, the case withδ=8︰1 has the best thermal performance,the second is the PT, and the last two are the cases ofδ=5︰4 and 1︰8. WhenP=11.25 mm, the thermal enhancement factor of the cases withδ=8︰1 and 5︰4 are higher than that of the PT, while the cases ofδ=1︰8 just have better performance than the PT at low Reynolds number. Generally, the longer the converging length is, the better the thermal performance.

    3.2.2Effect of tube pitch

    Figure 13 Variations of (a) Nusselt number and (b) friction factor for CDTs with different number twisted tapes versus Reynolds numbern: ● 2; ▲ 3; ▼ 4; 5; 6

    With other geometric parameters fixed, it is observed from Fig. 10 (a) and Fig. 11 (a) that the cases withP=11.25 mm show a large augment on Nusselt number over that of the cases withP=22.5 mm around 4.7% to 26.9%, especially for the cases withδ=8︰1. It is found in Figs. 10 (b) and 11 (b) that the increase in friction factor for cases withP=11.25 mm is in a range of 7.4% to 48% over the cases withP=22.5 mm. Besides, it is clearly seen from Fig. 12 that the shorter the pitch length is, the better the thermal enhancement factor behaves, except for the cases withP=11.25 mm,e=0.5 mm andδ=1︰8 atRe=20000 due to large pressure drop.

    3.2.3Effect of rib height

    It is illustrated in Fig. 11 that the Nusselt number and friction factor are found to noticeably increase with increasing rib height by fixing other geometric parameters. The increment of Nusselt number from the cases ofe=0.5 mm to the cases ofe=0.8 mm is greater than that from the cases ofe=0.8 mm to the cases ofe=1.1 mm, while the variations of friction factor tend to be opposite. Consequently, as shown in Fig. 12 (b), the cases withe=0.8 mm have the best thermal enhancement factor at most of the Reynolds number. This is because in the CDTs, the heat transfer enhancement in not only dominated by the rib configuration but also controlled by the swirl flow induced by the twin twisted tapes, so the best rib height in terms of the overall thermal performance is different from that in bare CDs. In addition, it is seen from Fig. 12 (b) that all cases of the CDTs exhibit better performance than the PT.

    3.2.4Effect of gap distance between twisted tapes

    Effect of the gap distance between twisted tapes on the heat transfer and fluid flow behaviors of the CDTs withP=11.25 mm,e=0.5 mm andδ=8︰1 is presented in Fig. 11. As the gap distance increases,both the Nusselt number and the friction factor decrease, and the decrement of the Nusselt number is lower than that of the friction factor. Hence, as seen in Fig. 12 (b), the thermal enhancement factor of the CDTs increases with the increase of gap distance. The reason is that the major thermal resistance and flow resistance in turbulent flow locate in the near wall zone and the mainstream zone, respectively. Consequently, a higher thermal performance (the maximumη=1.39) can be obtained by placing loose-fit twisted tapes in the near wall zone, reducing the thermal resistance as well as avoiding too much body resistance.

    3.2.5Effect of twisted tape number

    In order to know whether the thermal enhancement factor can be further improved by placing more twisted tapes in the near wall zone, the influence of the tape number on the heat transfer and flow resistance behaviors of CDTs withP=11.25 mm,e=0.5 mm,δ=8︰1 andb=8.5 is displayed in Figs. 13 (a)and 13 (b), respectively. It can be found that both the Nusselt number and friction factor rises with increasing tape number. This is because that the more number twisted tapes help to create more longitudinal vortices giving better mixing between the mainstream and the near wall regions and resulting in higher turbulence intensity and temperature gradient near the wall. Atn=3, 4, 5 and 6, the increases in Nusselt number are in a range of 4.5%-5%, 8.9%-9.5%, 16.4%-16.9%,22.5%-23.5%, respectively, over atn=2. However,the increments in friction factor atn=3, 4, 5 and 6,are respectively 30.7%-32.7%, 63.6%-69.7%, 102.7%-113%, 141%-157.5% over atn=2. As seen from Fig.14, atn=2, 3, 4, 5 and 6, the variation ranges of the thermal enhancement factors with Reynolds number areη=1.33-1.39, 1.27-1.32, 1.23-1.27, 1.22-1.26,1.21-1.25. This is due to the fact that the increment in flow resistance is higher than that in heat transfer rate with increasing tape number.

    Figure 14 Variations of η for CDTs with different number twisted tapes versus Reynolds numbern: ● 2; ▲ 3; ▼ 4; 5; 6

    3.2.6Flow structure

    Contour plots of velocity and streamlines for CDT-22.5-0.5-5︰4 and CDT-11.25-0.8-8︰1 are presented in Fig. 15. The figure shows that two types of flows are generated in tube. The one is straight flow near the tube wall, and the other is swirl flow induced by the twin twisted tapes which can improve fluid mixing between the mainstream zone and the near wall zone. The CDTs can simultaneously employ the transverse vortices from CDs and longitudinal vortices from twin twisted tapes to enhance heat transfer rate in a superimposed way, but they have higher pressure drop than their counterparts of CDs due to more body resistance. Consequently, compared with the bare CDs,the CDTs have higher heat transfer rate but have lower thermal enhancement factor. As Reynolds number increases, in general, the increase of pressure drop in the CDTs is much higher than that in heat transfer.Hence, generally, the overall thermal performance of the CDTs decreases as Reynolds number increases.

    Contour plots of turbulence intensity onY=0 mm plane atRe=10000 are illustrated in Fig. 16 for the CDTs with different geometric parameters. It is clearly seen that all CDTs have more intense and homogeneous turbulence intensity distribution than the plain tube, bare CDs and PT resulting from the double effect of the CDs and twin twisted tapes on the flow structure. The CDTs can not only improve turbulence intensity in the near wall zone but also in the mainstream zone. In other words, the heat transfer and flow characteristics are dominated by both the rib effect of CDs and the swirl flow effect of twisted tapes which govern the boundary layer separation and reattachment,secondary flow and flow recirculation in the tube.

    Contour plots of velocity vector and turbulence intensity for the CDTs (P1=11.25 mm,e=0.5 mm,δ=8︰1) with different gap distance (b) and tape number (n) onZ=11.25 mm plane atRe=10000 are presented in Fig. 17. One can see from Figs. 17 (a)-(c),the turbulence intensity decreases and distributes unevenly as gap distance increases, which indicates that the heat transfer deteriorates. This is because that the flow swirls on the tape decrease as the gap distance increases, and the axisymmetric swirl streams impinged to the tube wall become less and less, thus the mixing is increasingly inhomogeneous as the gap distance increases. Nonetheless, a lower pressure drop as well as a higher thermal enhancement factor can be gained for the cases with loose-fit tapes. It is observed from Figs. 17 (c)-(g) that in the near wall zone, the zones where the streams flow toward the wall have higher turbulence intensity than that in the zones where the streams flow away from the wall. In addition, the turbulence intensity increases with increasing tape number, which indicates that the heat transfer can be improved with the increase of tape number. Similarly, the more increase in pressure drop is accompanied by more tapes. Thus, the less the tape number, the better the overall thermal performance is.

    In conclusion, when the twisted tapes are used simultaneously in combination with CDs, it is observed from Figs. 10-14, the heat transfer rate and friction factor of the CDTs are higher than their counterparts of bare CDs around 6.3%-35.7% and 1.75-5.3 times, respectively. In addition, the thermal enhancement factor for the CDTs is between 1.01-1.39, which is lower than the corresponding bare CDs withη=1.23-1.59. The CDTs can make the distribution of thermal resistance and turbulence intensity to be more homogeneous to obtain a higher heat transfer rate. As a means of overcoming the shortcomings associated with the heat transfer enhancement only in the near wall zone by the bare CDs, the CDTs are promising heat exchangers aiming at enhancing heat transfer rate to the full extent with not too much pressure drop.

    Figure 15 Contour plots of velocity and streamlines at Re=10000

    3.3 Correlations

    Figure 18 presents the comparisons between the numerical values and those predicted by the respective correlations in Table 2. In the figures, the majority of the fitted values are agreeing with the numerical data within ±15 for both Nusselt number and friction factor.

    Figure 16 Contour plots of turbulence intensity for plain tube, PT and CDTs with different geometric parameters at Re=10000

    Figure 17 Plots of velocity vectors and turbulence intensity for CDTs with different b and n at Re=10000

    Figure 18 Comparisons between numerical values and predicted values○ CDs; □ CDTs

    Table 2 Summary of correlations for Nusselt number and friction factor

    4 CONCLUSIONS

    In this investigation, a numerical prediction has been conducted to study the heat transfer and flow characteristics of CDs and CDTs with varying geometric parameters in turbulent flow. The following are the conclusions of the present paper:

    (1) A finite volume method with Renormalizationgroup (RNG)k-εturbulence model is used in this study.The computations present that the predicted values are in good agreement with the results of the previous research. It is shown that the geometric parameters have an important influence on the thermal performances of both the CDs and the CDTs. By geometric optimizing, considerably enhanced heat transfer rate is achievable for both by decreasing the pitch length, by increasing the rib height, and by increasing the pitch ratio. In addition, the heat transfer rate of the CDTs increases with decreasing gap distance and increasing tape number.

    (2) The obtained results show that, for the CDs,the case withP=11.25 mm,e=0.5 mm andδ=8︰1 has the best thermal performance under the investigated geometric parameters. For the CDTs, the case withP=11.25 mm,e=0.5 mm,δ=8︰1 andb=8.5 mm has the best thermal performance. If the goal is to pursue the maximal heat transfer rate enhancement,the CDTs with tight-fit twisted tapes should be in consideration. If a better overall thermal performance is sought, the bare CDs (the largestη=1.59) or CDTs with loose-fit twisted tapes (the largestη=1.39)maybe worth of commendation.

    (3) The contour plots of predicted velocity,turbulence intensity and streamlines are presented for further understanding of the mechanism of compound heat transfer enhancement. It reveals that the CDs mainly promote turbulence intensity and heat transfer in the near wall zone. While, the simultaneous employment of the CDs and twin twisted tapes not only homogenizes turbulence intensity and enhances heat transfer rate in the near wall zone, but also does in the mainstream zone. In conclusion, the CDTs hold promise for practical applications.

    NOMENCLATURE

    bgap distance between twisted tapes, mm

    cthickness of twisted tape, mm

    cpspecific heat at constant pressure, J·kg-1·K-1dtube diameter, mm

    erib height, mm

    ffriction factor [f=2dΔp/(lρu2)]

    hheat transfer coefficient, W·m-2·K-1

    Llength of the tube section, mm

    Lperiodic length vector

    NuNusselt number (Nu=hd/λ)

    Ppitch length, mm

    PrPrandtl number (Pr=cpμ/λ)

    P1length of converging section, mm

    P2length of diverging section, mm

    ΔPpressure drop, Pa

    Qheat transfer rate, W

    ReReynolds number (Re=duρ/μ)

    rposition vector

    Ttemperature, K

    wtape width, mm

    ytwist ratio

    δpitch ratio (δ=P1/P2)

    Θ dimensionless temperature gradient

    λ fluid thermal conductivity, W·m-1·K-1

    μ fluid dynamic viscosity, kg·m-1·s-1

    ρ fluid density, kg·m-3

    Subscripts

    b bulk

    i inlet

    o outlet

    p plain tube

    w tube wall

    1 Bergles, A.E., “ExHFT for fourth generation heat transfer technology”, Exp. Therm. Fluid Sci., 26 (2-4), 335-344 (2002).

    2 Li, J., “Study on heat transfer performance and flow resistance performance of many kinds of heat transfer enhanced tube”, Master Thesis, South China University of Technology, Guangzhou (2000).(in Chinese)

    3 Chen, Y., Deng, X.H., Ding, X.J., Wang, Y.J., “Convection heat transfer of fully developed turbulent flow in shaped tubes with a new concept”, Int. Commun. Heat Mass Transfer, 31 (3), 355-364 (2004).

    4 Manglik, R.M., Bergles, A.E., “Heat transfer and pressure drop correlations for twisted-tape inserts in isothermal tubes: part I—Laminar flows”, J. Heat Transfer, 115 (4), 881-889 (1993).

    5 Manglik, R.M., Bergles, A.E., “Heat transfer and pressure drop correlations for twisted-tape inserts in isothermal tubes: part II—Transition and turbulent flows”, J. Heat Transfer, 115 (4), 890-897 (1993).

    6 Saha, S.K., Gaitonde, U.N., Date, A.W., “Heat transfer and pressure drop characteristics of laminar flow in a circular tube fitted with regularly spaced twisted-tape elements”, Exp. Therm. Fluid Sci., 2(3), 310-322 (1989).

    7 Saha, S.K., Gaitonde, U.N., Date, A.W., “Heat transfer and pressure drop characteristics of turbulent flow in a circular tube fitted with regularly spaced twisted-tape elements”, Exp. Therm. Fluid Sci., 3(6), 632-640 (1990).

    8 Abu-Khader, M.M., “Further understanding of twisted tape effects as tube insert for heat transfer enhancement”, Heat Mass Transfer, 43(2), 123-134 (2006).

    9 Wang, Y.J., Hou, M.L., Deng, X.H., Li, L., Huang, C., Huang, H.Y.,Zhang, G.F., Chen, C.H., Huang, W.J., “Configuration optimization of regularly spaced short-length twisted tape in a circular tube to enhance turbulent heat transfer using CFD modeling”, Appl. Therm.Eng., 31 (6-7), 1141-1149 (2011).

    10 Eiamsa-ard, S., Thianpong, C., Eiamsa-ard, P., “Turbulent heat transfer enhancement by counter/co-swirling flow in a tube fitted with twin twisted tapes”, Exp. Therm. Fluid Sci., 34 (1), 53-62 (2010).

    11 Eiamsa-ard, S., Promvonge, P., “Thermal characteristics in round tube fitted with serrated twisted tape”, Appl. Therm. Eng., 30 (13),1673-1682 (2010).

    12 Chang, S.W., Yang, T.L., Liou, J.S., “Heat transfer and pressure drop in tube with broken twisted tape insert”, Exp. Therm. Fluid Sci., 32(2), 489-501 (2007).

    13 Guo, J., Fan, A.W., Zhang, X.Y., Liu, W., “A numerical study on heat transfer and friction factor characteristics of laminar flow in a circular tube fitted with center-cleared twisted tape”, Int. J. Therm. Sci.,50 (7), 1263-1270 (2011).

    14 Murugesan, P., Mayilsamy, K., Suresh, S., “Turbulent heat transfer and pressure drop in tube fitted with square-cut twisted tape”, Chin.J. Chem. Eng., 18 (4), 609-617 (2010).

    15 Zimparov, V., “Enhancement of heat transfer by a combination of three-start spirally corrugated tubes with a twisted tape”, Int. J. Heat Mass Transfer, 44 (3), 551-574 (2001).

    16 Zimparov, V., “Enhancement of heat transfer by a combination of a single-start spirally corrugated tubes with a twisted tape”, Exp. Therm.Fluid Sci., 25 (7), 535-546 (2002).

    17 Nagarajan, P.K., Mukkamala, Y., Sivashanmugam, P., “Studies on heat transfer and friction factor characteristics of turbulent flow through a micro-finned tube fitted with left-right inserts”, Appl.Therm. Eng., 30 (13), 1666-1672 (2010).

    18 Promvonge, P., “Thermal augmentation in circular tube with twisted tape and wire coil turbulators”, Energy Convers. Manage., 49 (11),2949-2955 (2008).

    19 Eiamsa-ard, S., Nivesrangsan, P., Chokphoemphun, S., Promvonge,P., “Influence of combined non-uniform wire coil and twisted tape inserts on thermal performance characteristics”, Int. Commun. Heat Mass Transfer, 37 (7), 850-856 (2010).

    20 Bharadwaj, P., Khondge, A.D., Date, A.W., “Heat transfer and pressure drop in a spirally grooved tube with twisted tape insert”, Int. J.Heat Mass Transfer, 52 (7-8), 1938-1944 (2009).

    21 Webb, R.L., Eckert, E.R.G., “Application of rough surfaces to heat exchanger design”, Int. J. Heat Mass Transfer, 15 (9), 1647-1658(1972).

    22 Yakhot, V., Orszag, S.A., “Renormalised group analysis of turbulence: I. Basic theory”, J. Sci. Comput., 1 (1), 3-51 (1986).

    23 Incropera, F.P., Witt, P.D., Bergman, T.L., Lavine, A.S., Fundamentals of Heat and Mass Transfer, 6th edition, John-Wiley & Sons,Hoboken (2006).

    24 Durst, F., Fluid Mechanics, Springer, Berlin (2008).

    猜你喜歡
    連山
    相親
    賣書
    A 32-channel 100 GHz wavelength division multiplexer by interleaving two silicon arrayed waveguide gratings?
    秋游九寨溝
    異域中秋前數日漫思(新韻)
    百里臍橙連山山
    《玉函山房輯佚書·連山》佚文還原及文獻價值舉隅
    白日夫妻
    一名老警察的新追求:記葫蘆島市公安局連山分局關工委常務副主任劉春山
    中國火炬(2012年6期)2012-07-25 09:41:59
    連山縣城思源室建成開館
    源流(2012年10期)2012-04-29 14:35:23
    91麻豆精品激情在线观看国产| 一区二区三区四区激情视频 | 两个人的视频大全免费| 又黄又爽又免费观看的视频| 亚洲电影在线观看av| 蜜臀久久99精品久久宅男| 2021天堂中文幕一二区在线观| 亚洲自拍偷在线| 国产三级在线视频| 成人国产麻豆网| 亚洲av免费在线观看| 国产黄a三级三级三级人| 变态另类丝袜制服| 色综合站精品国产| 国产精品爽爽va在线观看网站| 免费看美女性在线毛片视频| 69av精品久久久久久| 性插视频无遮挡在线免费观看| 国产精品美女特级片免费视频播放器| 精品久久久久久久人妻蜜臀av| 亚洲第一区二区三区不卡| 精品国产三级普通话版| 天天躁日日操中文字幕| 国产大屁股一区二区在线视频| 欧美激情久久久久久爽电影| 搡女人真爽免费视频火全软件 | 99久久精品一区二区三区| 不卡一级毛片| 精品久久国产蜜桃| 国产视频内射| 两性午夜刺激爽爽歪歪视频在线观看| 精品不卡国产一区二区三区| 亚洲经典国产精华液单| 免费看日本二区| 人妻丰满熟妇av一区二区三区| 人人妻人人澡人人爽人人夜夜 | 美女被艹到高潮喷水动态| 免费无遮挡裸体视频| 1000部很黄的大片| 此物有八面人人有两片| 国产精品一及| 久久午夜福利片| 午夜精品国产一区二区电影 | 欧美zozozo另类| 久久久久国内视频| 男插女下体视频免费在线播放| 欧美zozozo另类| 人妻少妇偷人精品九色| 人妻久久中文字幕网| 日韩欧美在线乱码| .国产精品久久| 国产精品福利在线免费观看| 床上黄色一级片| 久久久久国内视频| 欧美成人免费av一区二区三区| av专区在线播放| 日本成人三级电影网站| 2021天堂中文幕一二区在线观| av免费在线看不卡| 淫秽高清视频在线观看| 天天躁日日操中文字幕| 熟女人妻精品中文字幕| 亚洲人成网站在线播| 亚洲人成网站在线观看播放| h日本视频在线播放| 国产一级毛片七仙女欲春2| 久久热精品热| 草草在线视频免费看| 国产成年人精品一区二区| 偷拍熟女少妇极品色| 99riav亚洲国产免费| 国产单亲对白刺激| 国产在线精品亚洲第一网站| 日韩在线高清观看一区二区三区| 网址你懂的国产日韩在线| av在线蜜桃| 美女大奶头视频| 亚洲国产欧洲综合997久久,| 综合色丁香网| 一本一本综合久久| 国产精品电影一区二区三区| 亚洲精品日韩在线中文字幕 | 午夜激情福利司机影院| 伦精品一区二区三区| 少妇人妻一区二区三区视频| 美女内射精品一级片tv| 天堂网av新在线| 成人毛片a级毛片在线播放| 成年女人永久免费观看视频| 欧美3d第一页| 国产精品一区二区三区四区免费观看 | 麻豆国产97在线/欧美| 一进一出抽搐动态| av在线亚洲专区| 日韩中字成人| 一本久久中文字幕| 干丝袜人妻中文字幕| 99久久精品国产国产毛片| 男女之事视频高清在线观看| 给我免费播放毛片高清在线观看| 99热全是精品| 麻豆成人午夜福利视频| 观看免费一级毛片| 夜夜看夜夜爽夜夜摸| 免费电影在线观看免费观看| 天美传媒精品一区二区| 嫩草影院新地址| 国产精品嫩草影院av在线观看| av在线播放精品| 午夜激情欧美在线| av在线老鸭窝| 国语自产精品视频在线第100页| 亚洲欧美精品综合久久99| 老女人水多毛片| 国产精品乱码一区二三区的特点| 两个人的视频大全免费| 国内揄拍国产精品人妻在线| 九九热线精品视视频播放| 成人无遮挡网站| 在线免费观看不下载黄p国产| av黄色大香蕉| 亚洲最大成人中文| 人人妻,人人澡人人爽秒播| 精品乱码久久久久久99久播| 男女之事视频高清在线观看| 最近2019中文字幕mv第一页| 日本三级黄在线观看| 色5月婷婷丁香| 22中文网久久字幕| 国产精品一及| 丝袜美腿在线中文| 桃色一区二区三区在线观看| 日本熟妇午夜| 久久国产乱子免费精品| 亚洲欧美清纯卡通| 伦精品一区二区三区| 久久亚洲精品不卡| 欧美色视频一区免费| 波多野结衣巨乳人妻| 国产精品无大码| 欧美成人a在线观看| 精品久久久久久久久久久久久| 不卡一级毛片| 亚洲av熟女| 亚洲第一电影网av| 国产黄片美女视频| 97碰自拍视频| 美女cb高潮喷水在线观看| 在线免费观看不下载黄p国产| 蜜桃亚洲精品一区二区三区| 国产 一区 欧美 日韩| 亚洲av五月六月丁香网| 3wmmmm亚洲av在线观看| 国产精品三级大全| 六月丁香七月| 干丝袜人妻中文字幕| 小蜜桃在线观看免费完整版高清| 久99久视频精品免费| 中文字幕久久专区| 国产白丝娇喘喷水9色精品| 少妇被粗大猛烈的视频| 69av精品久久久久久| 久久久久九九精品影院| 国产综合懂色| av福利片在线观看| 看非洲黑人一级黄片| 偷拍熟女少妇极品色| 最近的中文字幕免费完整| 中文字幕久久专区| 亚洲国产高清在线一区二区三| 欧美bdsm另类| av在线天堂中文字幕| 国产精品一区www在线观看| 十八禁国产超污无遮挡网站| 在线观看66精品国产| 美女大奶头视频| 嫩草影院精品99| 久久国内精品自在自线图片| 国产91av在线免费观看| 国产精品人妻久久久久久| 午夜福利在线观看免费完整高清在 | 日韩亚洲欧美综合| 亚洲美女搞黄在线观看 | 毛片女人毛片| 国产伦在线观看视频一区| 在线观看一区二区三区| 亚洲成人久久爱视频| 伦精品一区二区三区| 热99在线观看视频| 禁无遮挡网站| 亚洲人成网站在线观看播放| 99热只有精品国产| 午夜福利成人在线免费观看| 亚洲av中文av极速乱| 美女内射精品一级片tv| 国产精品人妻久久久久久| 久久99热这里只有精品18| 国产人妻一区二区三区在| 久久久久国产精品人妻aⅴ院| 黑人高潮一二区| 最新在线观看一区二区三区| 你懂的网址亚洲精品在线观看 | 十八禁网站免费在线| 国产精品伦人一区二区| 久久热精品热| 日本欧美国产在线视频| av天堂中文字幕网| 亚洲av第一区精品v没综合| 久久久精品大字幕| 搡女人真爽免费视频火全软件 | 麻豆久久精品国产亚洲av| 午夜亚洲福利在线播放| 国产成人a区在线观看| 欧美日本亚洲视频在线播放| 亚洲欧美中文字幕日韩二区| 国产亚洲精品久久久久久毛片| 我要看日韩黄色一级片| 啦啦啦观看免费观看视频高清| 亚洲成人中文字幕在线播放| 国产欧美日韩一区二区精品| 免费观看精品视频网站| 国产乱人视频| 床上黄色一级片| 成人漫画全彩无遮挡| 成年免费大片在线观看| 色综合色国产| 国产蜜桃级精品一区二区三区| 禁无遮挡网站| 国产精品电影一区二区三区| 麻豆久久精品国产亚洲av| 我的女老师完整版在线观看| 国产精品久久久久久av不卡| 国产91av在线免费观看| 黄色配什么色好看| 热99在线观看视频| 欧美成人a在线观看| 欧美国产日韩亚洲一区| av专区在线播放| 高清午夜精品一区二区三区 | 一级毛片电影观看 | 日韩人妻高清精品专区| 精品久久久久久久末码| 久久鲁丝午夜福利片| 亚洲内射少妇av| 日本在线视频免费播放| 久久人人精品亚洲av| 日韩亚洲欧美综合| 白带黄色成豆腐渣| 天美传媒精品一区二区| 亚洲丝袜综合中文字幕| 国产伦精品一区二区三区视频9| 一级黄片播放器| 亚洲中文字幕日韩| 日日干狠狠操夜夜爽| 99久久精品一区二区三区| 久久久久久久久大av| 桃色一区二区三区在线观看| 日韩精品青青久久久久久| 亚洲精品久久国产高清桃花| 一个人看的www免费观看视频| 狂野欧美激情性xxxx在线观看| 国产综合懂色| 色综合亚洲欧美另类图片| 最新在线观看一区二区三区| 波多野结衣高清无吗| 午夜福利视频1000在线观看| 亚洲专区国产一区二区| 免费搜索国产男女视频| 国产精品乱码一区二三区的特点| 免费看美女性在线毛片视频| 亚洲人成网站在线观看播放| 亚洲熟妇中文字幕五十中出| 久久久久久久亚洲中文字幕| 一进一出好大好爽视频| 女的被弄到高潮叫床怎么办| 91av网一区二区| 午夜激情欧美在线| 大型黄色视频在线免费观看| 国产人妻一区二区三区在| 亚洲人成网站在线播放欧美日韩| 欧美成人a在线观看| 国产午夜精品论理片| 少妇的逼好多水| 九九爱精品视频在线观看| 不卡一级毛片| 中国国产av一级| 在线播放国产精品三级| 神马国产精品三级电影在线观看| 国产精品久久久久久av不卡| 免费一级毛片在线播放高清视频| 国产一区二区三区av在线 | 一本久久中文字幕| 欧美zozozo另类| 亚洲美女搞黄在线观看 | 国产亚洲av嫩草精品影院| 国产在线精品亚洲第一网站| 日韩一本色道免费dvd| 欧美日韩乱码在线| 在线播放国产精品三级| 国产午夜福利久久久久久| 日韩强制内射视频| 久久久国产成人精品二区| 看十八女毛片水多多多| 国产精品免费一区二区三区在线| 51国产日韩欧美| 少妇熟女aⅴ在线视频| 在线免费观看的www视频| 毛片女人毛片| 色5月婷婷丁香| 一进一出好大好爽视频| 能在线免费观看的黄片| 国产精品乱码一区二三区的特点| 日本 av在线| 久久久久九九精品影院| 小蜜桃在线观看免费完整版高清| 人人妻人人澡欧美一区二区| 亚洲国产精品成人综合色| 一本精品99久久精品77| 老熟妇仑乱视频hdxx| 少妇裸体淫交视频免费看高清| 国产av一区在线观看免费| 日韩av不卡免费在线播放| 91在线精品国自产拍蜜月| 精品久久久久久久久久免费视频| 午夜福利在线在线| 一区二区三区免费毛片| av专区在线播放| eeuss影院久久| 老司机影院成人| 又黄又爽又免费观看的视频| 亚洲精品国产成人久久av| 一级毛片aaaaaa免费看小| 深夜精品福利| 久久久a久久爽久久v久久| 色综合亚洲欧美另类图片| 免费黄网站久久成人精品| 精华霜和精华液先用哪个| 国产亚洲欧美98| 此物有八面人人有两片| 麻豆精品久久久久久蜜桃| 此物有八面人人有两片| 99热这里只有是精品在线观看| 波多野结衣高清无吗| 国产黄色视频一区二区在线观看 | 三级男女做爰猛烈吃奶摸视频| 色播亚洲综合网| 国内精品一区二区在线观看| 久久韩国三级中文字幕| 三级经典国产精品| 成人无遮挡网站| 三级男女做爰猛烈吃奶摸视频| av卡一久久| 婷婷亚洲欧美| 毛片一级片免费看久久久久| av福利片在线观看| 春色校园在线视频观看| 麻豆久久精品国产亚洲av| 精品欧美国产一区二区三| 欧美三级亚洲精品| av女优亚洲男人天堂| 1000部很黄的大片| 最近的中文字幕免费完整| 91午夜精品亚洲一区二区三区| 国产成人aa在线观看| 老熟妇仑乱视频hdxx| 国产人妻一区二区三区在| 一区二区三区高清视频在线| 午夜激情福利司机影院| 村上凉子中文字幕在线| 欧美成人精品欧美一级黄| 97人妻精品一区二区三区麻豆| 国产精品伦人一区二区| 少妇丰满av| 免费黄网站久久成人精品| 精品国产三级普通话版| 国产大屁股一区二区在线视频| 国产私拍福利视频在线观看| 久久久久久久亚洲中文字幕| 亚洲精品粉嫩美女一区| 亚洲人成网站在线观看播放| 一级毛片久久久久久久久女| 国产精品国产高清国产av| 日日摸夜夜添夜夜爱| 99久久九九国产精品国产免费| 国产高清有码在线观看视频| 人人妻人人澡人人爽人人夜夜 | 大香蕉久久网| 在线观看午夜福利视频| 亚洲一区二区三区色噜噜| 亚洲国产精品成人久久小说 | 综合色av麻豆| 亚洲,欧美,日韩| 亚洲七黄色美女视频| 少妇熟女aⅴ在线视频| 69av精品久久久久久| 亚洲经典国产精华液单| 毛片女人毛片| 嫩草影视91久久| 国产视频内射| 国产不卡一卡二| 欧美日韩一区二区视频在线观看视频在线 | 欧美性感艳星| 少妇熟女aⅴ在线视频| 亚洲aⅴ乱码一区二区在线播放| 看十八女毛片水多多多| 亚洲欧美清纯卡通| 国内少妇人妻偷人精品xxx网站| 热99re8久久精品国产| 久久久午夜欧美精品| 色视频www国产| 国产 一区精品| 成年av动漫网址| 久久久久久伊人网av| 亚洲av成人精品一区久久| 亚洲国产欧洲综合997久久,| 国产精品人妻久久久久久| 少妇裸体淫交视频免费看高清| 黄色配什么色好看| 亚洲精品国产av成人精品 | 国产单亲对白刺激| 久久亚洲精品不卡| 精品久久久久久久久久免费视频| 成人特级av手机在线观看| 色5月婷婷丁香| 亚洲av熟女| 成年版毛片免费区| а√天堂www在线а√下载| 亚洲人成网站在线播| 成人综合一区亚洲| 91麻豆精品激情在线观看国产| 欧美色欧美亚洲另类二区| av在线观看视频网站免费| 国产视频内射| 日韩精品青青久久久久久| 国内精品宾馆在线| 三级男女做爰猛烈吃奶摸视频| 性插视频无遮挡在线免费观看| 99久久九九国产精品国产免费| av视频在线观看入口| 久久久久国产精品人妻aⅴ院| 岛国在线免费视频观看| 日韩精品中文字幕看吧| 国产高清有码在线观看视频| 黄色配什么色好看| 毛片一级片免费看久久久久| 欧美不卡视频在线免费观看| 嫩草影院新地址| 看免费成人av毛片| 深爱激情五月婷婷| 欧美日本视频| 亚洲性夜色夜夜综合| 欧美日韩国产亚洲二区| 欧美一区二区国产精品久久精品| 一级毛片aaaaaa免费看小| 亚洲一区高清亚洲精品| 国产伦一二天堂av在线观看| 精品乱码久久久久久99久播| 中文字幕免费在线视频6| 国产三级中文精品| 国产片特级美女逼逼视频| 99视频精品全部免费 在线| 亚洲国产精品成人综合色| 国产亚洲精品综合一区在线观看| 亚洲国产欧洲综合997久久,| 欧美成人免费av一区二区三区| 蜜臀久久99精品久久宅男| 精品一区二区三区视频在线| 成人高潮视频无遮挡免费网站| 欧美日韩乱码在线| 免费人成在线观看视频色| 深夜精品福利| 在线播放国产精品三级| 午夜影院日韩av| 少妇人妻精品综合一区二区 | 最近最新中文字幕大全电影3| 少妇的逼好多水| 欧美+日韩+精品| videossex国产| 成人毛片a级毛片在线播放| 欧美3d第一页| 国产精品免费一区二区三区在线| 国产精品人妻久久久久久| 91久久精品国产一区二区成人| 免费观看在线日韩| 日本撒尿小便嘘嘘汇集6| 3wmmmm亚洲av在线观看| 成人综合一区亚洲| 日本爱情动作片www.在线观看 | aaaaa片日本免费| 热99在线观看视频| 国产av麻豆久久久久久久| 一个人免费在线观看电影| 国产老妇女一区| 少妇人妻精品综合一区二区 | 精品久久久久久久久av| 人妻制服诱惑在线中文字幕| 禁无遮挡网站| 村上凉子中文字幕在线| 最近最新中文字幕大全电影3| 狂野欧美激情性xxxx在线观看| 免费无遮挡裸体视频| 麻豆成人午夜福利视频| eeuss影院久久| 午夜精品一区二区三区免费看| 欧美一区二区亚洲| 你懂的网址亚洲精品在线观看 | 人妻少妇偷人精品九色| 欧美bdsm另类| 国产欧美日韩精品一区二区| 女人十人毛片免费观看3o分钟| 国内精品美女久久久久久| 最新在线观看一区二区三区| 丰满人妻一区二区三区视频av| 在线国产一区二区在线| 天天躁日日操中文字幕| 男女啪啪激烈高潮av片| 色尼玛亚洲综合影院| 一级毛片电影观看 | 老师上课跳d突然被开到最大视频| 91久久精品国产一区二区三区| 熟妇人妻久久中文字幕3abv| 给我免费播放毛片高清在线观看| 国产一区二区三区av在线 | 免费在线观看影片大全网站| 精品午夜福利视频在线观看一区| 国产亚洲91精品色在线| 国产精品乱码一区二三区的特点| 最近在线观看免费完整版| 一级a爱片免费观看的视频| 国产在线精品亚洲第一网站| 日本免费a在线| 欧美日韩一区二区视频在线观看视频在线 | 亚洲欧美清纯卡通| 亚洲乱码一区二区免费版| 久久久a久久爽久久v久久| 免费看美女性在线毛片视频| 亚洲第一区二区三区不卡| 又爽又黄无遮挡网站| 亚洲18禁久久av| 少妇熟女aⅴ在线视频| av女优亚洲男人天堂| 男女下面进入的视频免费午夜| av专区在线播放| 欧美成人a在线观看| 男人舔奶头视频| 别揉我奶头 嗯啊视频| 国产精品爽爽va在线观看网站| 成人亚洲欧美一区二区av| 欧美色欧美亚洲另类二区| 丰满人妻一区二区三区视频av| 欧美+日韩+精品| 好男人在线观看高清免费视频| eeuss影院久久| 国产激情偷乱视频一区二区| 美女内射精品一级片tv| 国产男靠女视频免费网站| 日本一本二区三区精品| av在线播放精品| 精品人妻偷拍中文字幕| 国内久久婷婷六月综合欲色啪| 综合色av麻豆| 成人特级黄色片久久久久久久| 又爽又黄无遮挡网站| 久久人人爽人人爽人人片va| 国产精品国产高清国产av| 一进一出抽搐动态| 久久99热这里只有精品18| 中国美白少妇内射xxxbb| 禁无遮挡网站| 欧美bdsm另类| 亚洲在线观看片| 成人漫画全彩无遮挡| 亚洲av五月六月丁香网| 国产亚洲av嫩草精品影院| 国产亚洲精品av在线| 久久久午夜欧美精品| 特大巨黑吊av在线直播| 高清日韩中文字幕在线| 亚洲丝袜综合中文字幕| 观看美女的网站| 一个人看视频在线观看www免费| 97热精品久久久久久| 亚洲精品日韩在线中文字幕 | 麻豆国产av国片精品| 人人妻,人人澡人人爽秒播| 久久精品国产亚洲av天美| 色哟哟·www| 国产毛片a区久久久久| 欧美色视频一区免费| 日本色播在线视频| 精品一区二区三区av网在线观看| 国产一区二区三区在线臀色熟女| 国语自产精品视频在线第100页| 亚洲欧美中文字幕日韩二区| 3wmmmm亚洲av在线观看| 别揉我奶头 嗯啊视频| 九色成人免费人妻av| 亚洲性久久影院| 99riav亚洲国产免费| 嫩草影视91久久| 亚洲精品乱码久久久v下载方式| 精品久久国产蜜桃| 欧美潮喷喷水| 岛国在线免费视频观看| 国产精品一区二区性色av| 国产v大片淫在线免费观看| 国产精品人妻久久久影院| 伊人久久精品亚洲午夜| 最近在线观看免费完整版| 精品久久久久久久久亚洲| 免费人成在线观看视频色| 日韩av在线大香蕉| 日本免费一区二区三区高清不卡| 免费黄网站久久成人精品| 国国产精品蜜臀av免费|