• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Novel fast lithium-ion conductor LiTa2PO8 enhances the performance of poly(ethylene oxide)-based polymer electrolytes in all-solid-state lithium metal batteries

    2022-09-16 05:25:06YingZheChenZhongkiXuQiAnXiZhngXiohongSunShuCiChunmingZheng
    Chinese Chemical Letters 2022年8期

    Ying N, Zhe Chen, Zhongki Xu, Qi An, Xi Zhng, Xiohong Sun,?, Shu Ci,Chunming Zheng

    a School of Materials Science and Engineering, Key Laboratory of Advanced Ceramics and Machining Technology of Ministry of Education, Tianjin University,Tianjin 300072, China

    b School of Chemistry and Chemical Engineering, State Key Laboratory of Hollow-fiber Membrane Materials and Membrane Processes, Tiangong University,Tianjin 300387, China

    ABSTRACT At present, replacing the liquid electrolyte in a lithium metal battery with a solid electrolyte is considered to be one of the most powerful strategies to avoid potential safety hazards.Composite solid electrolytes(CPEs) have excellent ionic conductivity and flexibility owing to the combination of functional inorganic materials and polymer solid electrolytes (SPEs).Nevertheless, the ionic conductivity of CPEs is still lower than those of commercial liquid electrolytes, so the development of high-performance CPEs has important practical significance.Herein, a novel fast lithium-ion conductor material LiTa2PO8 was first filled into poly(ethylene oxide) (PEO)-based SPE, and the optimal ionic conductivity was achieved by filling different concentrations (the ionic conductivity is 4.61×10?4 S/cm with a filling content of 15 wt% at 60°C).The enhancement in ionic conductivity is due to the improvement of PEO chain movement and the promotion of LiTFSI dissociation by LiTa2PO8.In addition, LiTa2PO8 also takes the key in enhancing the mechanical strength and thermal stability of CPEs.The assembled LiFePO4 solid-state lithium metal battery displays better rate performance (the specific capacities are as high as 157.3, 152, 142.6, 105 and 53.1 mAh/g under 0.1, 0.2, 0.5, 1 and 2 C at 60°C, respectively) and higher cycle performance (the capacity retention rate is 86.5% after 200 cycles at 0.5 C and 60°C).This research demonstrates the feasibility of LiTa2PO8 as a filler to improve the performance of CPEs, which may provide a fresh platform for developing more advanced solid-state electrolytes.

    Keywords:Composite solid electrolyte All-solid-state lithium metal battery LiTa2PO8 Poly(ethylene oxide)Lewis acid

    Recent years have witnessed a spurt of demand for huge energy storage in social development and human life, the growth of power batteries with more reliable safety, higher energy density and longer cycle life has become a new research direction [1].Lithium metal is considered to be the most ideal anode by reason of its high theoretical capacity (3860 mAh/g) and low standard potential (?3.04 V) [2,3].Nevertheless, the high reactivity of lithium metal causes side reactions with liquid electrolytes.In particular, uncontrolled accumulation of lithium dendrites can cause a short circuit in the battery [4–6].In addition, the liquid electrolyte is composed of numerous organic solvents, which can cause serious safety hazards in the application, such as combustion and explosion [7–9].Accordingly, traditional liquid electrolytes cannot be applied to lithium metal batteries.

    The solid electrolyte (SSE) is considered a hopeful candidate material to replace liquid electrolyte by the reason of its great thermal stability, high mechanical strength and good electrochemical stability [10].Generally, SSEs can be composed of inorganic solid electrolytes (ISEs) and solid polymer electrolytes (SPEs) [11].ISEs have excellent thermal stability and great ionic conductivity [12].However, ISEs in the ceramic state do not form good contact with the electrode interface [13,14].Large interfacial impedance will inhibit the lithium-ion transfer between them, resulting in a battery with low capacity and short cycle life [15].In contrast, the flexible height of SPEs has a good affinity with electrodes [16].PEO is the most broadly used SPE at present, but its poor mechanical properties and low ionic conductivity (≤10?7S/cm at 25°C) seriously impede its practical utilization as a single material [17].In order to overcome these shortcomings, dispersing inorganic fillers into PEO to form PEO-based CPEs has been manifested to be one of the most valid methods to enhance the capability of all-solid-state lithium metal batteries (ASSLMBs) [18,19].The introduction of inorganic fillers will reduce the flammability and raise the mechanical properties of the CPE [20,21].Inorganic fillers are divided into inert fillers (Al2O3, TiO2, SiO2and CeO2,etc.) [22–24] and active fillers (perovskite-type, garnet-type and NASICON-type,etc.) [25–27].Notably, active fillers not only enhance the overall Li+mobility by enhancing the segment movement of the PEO polymer chain as well as inert fillers, but they also allow rapid Li+transport within the ceramic and create fast lithium-ion transport channels at the PEO/ceramic interface, thus achieving extraordinary synergistic effects [28,29].

    Although CPEs have the common advantages of ISEs and SPEs,they still have many problems, for instance, poor mechanical performances and low ion conductivity.Hence, there is still a big challenge to develop a CPE with both distinguished electrochemical and safety capabilities.That is, the devise and composite of new materials are of great significance.Recently, Kimet al.[30] declared a new solid lithium-ion conductor LiTa2PO8(LTPO) with theoretical and practical conductivity of 35.3 mS/cm and 0.25 mS/cm at 25°C, respectively.It is comparable with Li7La3Zr2O12(garnet-type) and Li3/8Sr7/16Ta3/4Zr1/4O3(perovskitetype).Furthermore, Fiazet al.[31] used ab initio molecular dynamics simulations to show that the crystal structure of LTPO is very stable during the lithium-ion diffusion process.Its activation energy is only 0.16 eV, which is lower than that of garnettype Li7La3Zr2O12, NASICON-type LiGe2(PO4)3and perovskite-type Li3xLa2/3-xTiO3.Meanwhile, Huanget al.[32] used LTPO as an inorganic solid electrolyte material to form an ASSLMB (the cathode is LiFePO4).At 55°C, its specific capacity can still reach 110 mAh/g after 85 cycles under 0.1 mA/cm2.This work also shows that LTPO exhibits good chemical stability in the air, aqueous solutions and organic solvents, which is better than traditional sulfide and garnet-type solid electrolytes.For example, Li10GeP2S12has strong hygroscopicity and easily generates toxic hydrogen sulfide gas in contact with moisture [33].Li7La3Zr2O12forms a Li+insulating Li2CO3layer on the surface through H+/Li+exchange,having a large interface impedance [34].In addition, the commonly studied NASCION-type (Li1+xAlxTi2-x(PO4)3) and perovskitetype (Li3xLa2/3-xTiO3) electrolytes react with lithium metal to reduce Ti4+to Ti3+, producing electron conduction [35].The nitridetype (LiPON) is also unstable to metal lithium and the process of assembling the battery is complicated (it needs to be magnetron sputtered to Li anode for use), which limits its large-scale application [36].All these results have shown that the experimental research of PEO-LiTa2PO8CPE is of outstanding significance to broaden the development of ASSLMBs.

    Herein, LTPO is first adopted as an active filler in PEO-based solid electrolytes to achieve the best ionic conductivity by filling different concentrations.The results show that 15 wt% LTPO can effectively optimize the ionic conductivity (4.61×10?4S/cm) and lithium-ion mobility (0.448) of the PEO-based solid electrolytes at 60°C.Importantly, this work has investigated the improvement mechanism of LTPO on PEO-based polymers in detail through various electrochemical, chemical, and mechanical characterizations.For the LiFePO4-ASSLMB assembled by PEO-LiTFSI-15 wt% LTPO CPE, it can achieve better rate performance, higher capacity and longer cycle performance at 60°C.Further, the uniform lithium metal interface can be observed after cycling, indicating that PEOLiTFSI-15 wt% LTPO has excellent compatibility with the lithium metal interface.This strategy opens a fresh way for the development of potentially superior performance CPEs.

    Fig.1.(a) XRD patterns of PEO-LiTFSI-xLTPO (0, 10, 15, 20 and 30 wt%) membranes.(b-f) Surface SEM images of PEO-LiTFSI-xLTPO (0, 10, 15, 20 and 30 wt%) membranes.(g) Elemental mappings of P-Li-15LTPO membrane.(h, i) The cross-sectional SEM images of P-Li and P-Li-15LTPO membranes.

    As shown in Fig.S1a (Supporting information), the prepared LTPO has an irregular particle distribution with a small particle size (~1 μm).The composite membranes with different LTPO content are prepared by the casting method, and they are wrapped by PEO matrix.The XRD patterns of LTPO powders, pure PEO and PEO-LiTFSI-xLTPO (0, 10, 15, 20 and 30 wt%) membranes are presented in Figs.S1b and S2 (Supporting information) and Fig.1a.The crystal structure of LTPO has almost no impurity phase consistent with previous reports (Fig.S1b) [30,32].The prepared SSE membranes have a crystalline phase similar to that of PEO, which can be seen by comparison with the XRD pattern of pure PEO (Fig.S2).In addition, it is noteworthy that the characteristic peak intensity of P-Li reduces notably with the increase of LTPO powders doping [37].Therefore, the introduction of LTPO can lower the crystallinity of PEO obviously, which is conducive to the transfer of Li+[38].It is because of Li+coordinates with the ether oxygen atom (-C-O-C) of the PEO segment through complexation in the PEO-based polymer electrolyte [39,40].These coordinated Li+migrate between or within polymer segments and chains as the lithium-oxygen (Li-O) bonds are broken/formed [41,42].At the same time, the polymer segments rearrange and move to transport Li+over long distances.Thus, the increase of the amorphous region in PEO can increase the movement of Li+in the electrolyte,that is, the introduction of LTPO is effective [43].To further observe the SSEs, the surface morphology of the membranes with different LTPO content was characterized by SEM (Figs.1b-f).These images show that the PEO matrix can be tightly combined with LTPO and the resulting membrane surface is very smooth when LTPO mixing amounts are 10 wt% and 15 wt%.However, when the addition amount reaches 20 wt% or above, the excessive LTPO particles will agglomerate and lead to an uneven surface of the membrane.This is not conducive to the mutual contact between the SSEs and the electrodes and hinders the transmission of Li+in the SSE membranes.Especially, element mapping was performed on the P-Li-15LTPO membrane.According to Figs.1d and g, the elements O, P and Ta are homogeneously distributed in the membrane.Furthermore, the thickness of the P-Li and P-Li-15LTPO membranes are about ~110 μm and ~120 μm, respectively, as shown in Figs.1h and i.

    Fig.2.(a) TGA curves of P-Li and P-Li-15LTPO membranes.(b) Strain-stress curves of P-Li and P-Li-15LTPO membranes.(c) Arrhenius plots of the PEO-LiTFSI-xLTPO (0, 10,15, 20 and 30 wt%) SSEs at 25–80°C.(d) DSC curves of P-Li and P-Li-15LTPO SSEs.(e) The mechanism schematic of LTPO in PEO-based electrolyte.(f) FTIR spectra of the P-Li and P-Li-15LTPO SSEs at 1400–1160 cm?1.(g) The chronoamperometry curves of P-Li-15LTPO CPE at a potential step of 10 mV at 60°C (the inset figure displays EIS of the cell before and after polarization).

    The thermal stability of SSEs is critical for future applications of high-performance ASSLMBs, especially for safety performance[21,44].Fig.2a shows the TGA curves of two SSE membranes (with or without LTPO powders added).The results show that both samples suffered a slight weight loss (2%) below 100°C, which is attributed to the evaporation of water absorbed from the atmosphere.At 350–460°C, the serious quality loss of both is attributed to the decomposition of PEO and LiTFSI [45].However, the remaining mass (14.85 wt%) of the P-Li-15LTPO membrane is significantly higher than the P-Li membrane (5.82 wt%) at 800°C.It is because LTPO still has excellent structural stability and chemical stability at high temperatures.These results demonstrate that LTPO powders can ameliorate the thermal stability of PEO-based electrolytes and prevent the internal short circuit phenomenon of the battery caused by the thermal decomposition of the electrolyte to a certain extent, thereby reducing the occurrence of battery safety accidents.For the sake of more directly observe the stability of the membrane at high temperature, the flammability of conventional liquid electrolytes (1 mol/L LiPF6in EC/DEC/EMC with equal volume) and SSEs with or without LTPO were compared.As shown in Fig.S3 (Supporting information), the traditional liquid electrolyte burns instantly upon contact with the torch heater and quickly burns into ashes.P-Li and P-Li-15LTPO membranes are ignited after 10 s but do not burn continuously (the flame goes out instantly as soon as it leaves the torch heater).After the burning test, the P-Li membrane has many holes and cannot maintain its original shape to become a viscous liquid.Inversely, the P-Li-15LTPO membrane only has a hole in the place where the fire is most prosperous,and it can almost maintain its integrity.Thus, the addition of LTPO powders can maintain the shape of PEO-based electrolytes at high temperatures and improve the safety of ASSLMBs.

    Moreover, the security performance of ASSLMBs is also related to the mechanical performance of SSEs [46].Electrolyte membranes with high mechanical properties can restrain the continuous growth of lithium dendrites and prevent ASSLMBs from shortcircuiting.Therefore, the P-Li and P-Li-15LTPO membranes were subjected to tensile tests, and the strain-stress curves obtained are shown in Fig.2b.The results display that the tensile strength of the P-Li-15LTPO membrane is 496.54 KPa, which is higher than the 393.56 KPa of the P-Li membrane.Furthermore, P-Li-15LTPO membrane also has a high plastic strain, nearly 479%.In simple terms,LTPO ceramics can effectively inhibit dendrites as a physical barrier, thus improving the operating stability of batteries.The above results fully demonstrate that the P-Li-15LTPO membrane can be used as a safe and reliable CPE in an ASSLMB.

    In addition to the above two properties, the electrochemical performances of SSEs are also very important for batteries in practical applications.Firstly, the AC impedance characterization of SSEs with different contents of LTPO was carried out at 25°C (Fig.S4 in Supporting information).Among all the samples, the minimum impedance of the sample containing 15 wt% LTPO powders is about 815Ωless than 1065Ωfor P-Li.Fig.2c is the Arrhenius plots of SSEs with different LTPO contents at 25–80°C.It is obvious that the ionic conductivity (σ) enhances with increasing temperature.when the doping amount reaches 15 wt%, theσof SSE is about twice that of P-Li SSE (4.61×10?4S/cmvs.2.38×10?4S/cm, at 60°C).Combined with previous studies on the modification mechanism of CPEs, the theory of LTPO powders in PEO-based electrolytes is devised and explained in three aspects [47,48].First,LTPO inorganic powders can remarkably reduce the crystallinity of PEO and strength the segment movement of the polymer, thereby improving the overall ionic conductivity.This explanation can be confirmed by combining the XRD patterns earlier and the following DSC.Fig.2d gives the DSC curves of two SSE membranes with and without LTPO.It can be seen that the melting transition (Tm)of SSE decreased from 63°C to 60.1°C after adding LTPO powders.This further proves that the additive LTPO does decrease the crystallinity of PEO and promote ion migration [49].Second, there is a strong interaction between the Lewis acid center of LTPO and TFSI?, which leads to the separation of Li+from LiTFSI to release more Li+(Fig.2e) [20,50-52].To confirm this hypothesis,FTIR tests were performed on samples with and without LTPO.Fig.S5 (Supporting information) and Fig.2f demonstrate the complete(4000–400 cm?1) and detailed (1400–1150 cm?1) FTIR spectra of LTPO, P-Li and P-Li-15LTPO, respectively.Among them, the peaks near 1351, 1342, 1280 and 1241 cm?1are attributed to pure PEO,and the other peaks belong to the symmetrical and asymmetrical stretching of -SO2- and -CF3groups in LiTFSI.By comparison,when 15 wt% LTPO ceramic powders were added, the peak of -SO2- asymmetric stretching at 1333.8 and 1304 cm?1moved to 1333.1 and 1302.5 cm?1, respectively.Meanwhile, the peaks of -CF3symmetric stretching at 1227.4 cm?1moved to 1228.4 cm?1,and the peaks of -CF3asymmetric stretching at 1198.4 and 1181.2 cm?1migrated to 1193.2 and 1178.5 cm?1, separately.The changes of -SO2- and -CF3group peaks indicate that there is a strong interaction between LTPO fillers and LiTFSI.Hence, the introduction of LTPO can promote the divorce of the LiTFSI and release more Li+to increase the ionic conductivity.Finally, the large number of Lewis acid sites on the LTPO can facilitate Li+migration at the phase interface between the PEO and LTPO [20].However, excessive addition of LTPO will result in a decrease in theσof SSEs(>15 wt%).This is because the entire area where ions migrate in the CPE contains the polymer, the active fillers, and the interface phase between the polymer and the active fillers [53].In this system, first of all, excessive LTPO leads to a reduction in the miscibility of PEO and LTPO, hindering the transfer of ions in the polymer [8,10].It can also be obtained from the above analysis of the SEM images.Secondly, an appropriate amount of LTPO forms a connected percolation network to support the diffusion of ions through the LTPO phase, while excessive LTPO causes irregular agglomeration effects and hinders the diffusion of ions [54].Finally, the clustering phenomenon caused by excessive LTPO can also cause a sharp reduction in the volume ratio of the interface between the polymer and the active fillers, which leads to a significant decrease in ionic conductivity [55].Fig.2g and Fig.S6 (Supporting information) respectively show the DC polarization curve and the AC impedance spectrum of the Li||SSE||Li cells composed of two SSEs (P-Li and P-Li-15LTPO SSEs).The results display that thetLi+of P-Li-15LTPO CPE is 0.448, much higher than that of P-Li SSE (0.141).The increase intLi+is going to be attributed to the interaction between LTPO and -SO2- and -CF3groups in LiTFSI, which can also be proved by the FTIR analysis above.

    Fig.3.(a) LSV plots of P-Li and P-Li-15LTPO SSEs at 1.0 mV/s.(b) Galvanostatic cycling curves of Li||P-Li||Li and Li||P-Li-15LTPO||Li cells at different current densities.(c)Galvanostatic cycling curves of Li metal plating/stripping under 0.1 mA/cm2 (the inset shows a magnified plot from 495 h to 500 h).(d) Rate performance of LFP||P-Li||Li and LFP||P-Li-15LTPO||Li cells.(e) Cycle performance of LFP||P-Li-15LTPO||Li cell at 0.2 C.(f) Long cycling performance of LFP||P-Li||Li and LFP||P-Li-15LTPO||Li cells.(g) EIS of LFP||P-Li-15LTPO||Li cell before and after 200 cycles.All tests are performed at 60°C.

    Another important factor of ASSLMBs is the electrochemical stability under working voltage [56].For the sake of determining the working voltage range of the sample, the electrochemical window of the SS||SSE||Li cells was studied using LSV at 60°C.As exhibited in Fig.3a, the initial decomposition potential of P-Li-15LTPO CPE is similar to that of P-Li SSE, about 4.1 V.It is due to the stable electrochemical window of LTPO ceramic powders being 2.01 ~4.01 V [31].To further explore the interface stability of SSE membranes/lithium metal, the lithium plating/stripping behavior of the two SSE membranes was measured at different current densities by assembling Li||SSE||Li cells (0.05, 0.1, 0.2 and 0.3 mA/cm2at 60°C).Fig.3b describes that Li||P-Li-15LTPO||Li cell presents a lower polarization voltage at all current densities and generates a more favorable electrolyte/lithium anode interface.Inversely, Li||P-Li||Li cell produces a greater polarization and shortcircuit at 0.3 mA/cm2.Otherwise, for the long-cycle lithium plating/peeling behavior test at 0.1 mA/cm2, Li||P-Li-15LTPO||Li cell also shows better stability (Fig.3c).Li||P-Li||Li cell has a short circuit after 340 h, while Li||P-Li-15LTPO||Li cell has a stable cycle for more than 500 h and its lithium plating/stripping overpotential remains at ~32 mV.The lithium symmetry test shows that the prepared PLi-15LTPO CPE has good stability with the lithium metal anode.Appropriately, the SSE can be paired with a lithium metal anode to build an advanced ASSLMB.

    The ASSLMBs with lithium metal anodes, LFP cathodes and P-Li or P-Li-15LTPO electrolytes were constructed.Fig.3d exhibits the rate performance of LFP||P-Li||Li and LFP||P-Li-15LTPO||Li cells at 60°C.The initial discharge specific capacity of LFP||P-Li-15LTPO||Li cell is 157.3, 152, 142.6, 105 and 53.1 mAh/g at 0.1, 0.2, 0.5, 1 and 2 C, respectively.Almost all higher than LFP||P-Li||Li cell (153.9,152.1, 142.6, 55 and 13.4 mAh/g), especially at high rates.It proves that the mixture of LTPO powders can greatly optimize the rate capacity.As the current density is readjusted to 0.5 C, the battery containing LTPO can still provide a high discharge capacity of 136.3 mAh/g and can be kept stably, while the capacity of the battery without LTPO is only 128.9 mAh/g and decays gradually.Additionally, according to the corresponding charge and discharge curves (Fig.S7 in Supporting information), the overpotential of the two batteries will increase with the increase of current density.As a stark comparison, ASSLMB using P-Li-15LTPO electrolyte has low voltage polarization and a flat working platform.It indicates that LTPO can improve interface compatibility of the electrolyte/electrode, which is beneficial to the stability of the battery.

    The long-term cycle properties of LFP||P-Li||Li and LFP||P-Li-15LTPO||Li cells are illustrated in Figs.3e and f.At low current density (0.2 C), LFP||P-Li-15LTPO||Li cell delivers stable cycling properties (Fig.3e).Its initial discharge capacity is 150.9 mAh/g, and the capacity retention rate can attain 97% after 70 cycles.At high current densities (0.5 C), both batteries provide lower capacity in the first cycle, implying an active process (Fig.3f).Meanwhile,the coulombic efficiency of the two batteries in the early stage is higher than 100%.This is because the cathode not only inserts the originally extracted lithium but also inserts the lithium provided by the lithium metal during the early discharge process,which leads to this phenomenon [20,57,58].In particular, LFP||PLi-15LTPO||Li cell exhibits ultrahigh specific discharge capacity of 128.4 mAh/g after 200 cycles, and the capacity retention rate is close to 86.5%.For LFP||P-Li||Li cell, its discharge specific capacity decayed rapidly from 151.4 mAh/g to 109.9 mAh/g within 60 cycles, and then a short-circuit occurred.Due to the violent polarization between P-Li SSE and lithium metal along with the continuous generation of lithium dendrites during the cycle, a large number of deposited lithium dendrites break through the electrolyte and cause a short circuit eventually.By contrast, the LFP||PLi-15LTPO||Li cell still displays a constant voltage polarization after 200 cycles (Fig.S8 in Supporting information).Obviously, ASSLMB composed of P-Li-15LTPO has better cycle performance.It can be attributed to two aspects [59,60].On the one hand, the LTPO ceramic powders enhance the mechanical strength of the SSE, so that it has enough stress to hinder the penetration of lithium dendrites.This guarantees battery stability during long-term cycling.On the other hand, LTPO ceramic powders can decrease the crystallinity of the polymer and release more Li+viaLewis acidsites effectively,thereby raising the ionic conductivity andtLi+of the SSE.This can improve battery cycle performance greatly.

    Fig.4.Surface SEM images of Li anodes in the (a, b) LFP||P-Li||Li and (c, d) LFP||PLi-15LTPO||Li cells after 200 cycles at 0.5 C.

    The cycle performance is also approximately related to the interface stability of the electrolyte/electrode [61].Perform EIS on LFP||P-Li||Li and LFP||P-Li-15LTPO||Li cells before and after the cycle, as demonstrated in Fig.3g and Fig.S9 (Supporting information).Compared with P-Li SSE, the ASSLMB composed of P-Li-15LTPO CPE has a smaller resistance (62.05Ω vs.66.81Ω).Furthermore, the resistance of LFP||P-Li-15LTPO||Li cell changes slightly after cycling (476.16Ω vs.2332Ω).In other words, the addition of 15 wt% LTPO improves the interface compatibility of solid electrolyte/electrode, enhancing the cycle performance of the battery greatly [62].Fig.4 displays the SEM images of lithium metal anodes in LFP||P-Li||Li and LFP||P-Li-15LTPO||Li cells after long loop.The results show that the lithium anode surface from the battery without LTPO is uneven and possesses large quantities of lithium dendrites.On the contrary, the lithium anode from the battery containing LTPO has a relatively flat surface and a small number of lithium dendrites.These results are in accordance with the electrochemical test consequences, indicating that the SSE containing LTPO can effectively prevent the growth of lithium dendrites.The inhibition ability of P-Li-15LTPO CPE on lithium dendrites growth can be ascribed to its excellent ionic conductivity and mechanical strength [63,64].Among them, the higher ionic conductivity can facilitate the rapid diffusion of Li+in the electrolyte, so that the Li deposition is uniform.Meanwhile, sufficient mechanical strength inhibits the lithium dendrites’growth and avoids the occurrence of short circuits.These excellent electrochemical properties prove that LTPO ceramic powders as an active additive effectively strengths the electrochemical properties of PEO-based electrolytes, and the ASSLMBs composed of them also have high development potential.

    In all, we analyze the effect of LTPO powers on the physical and electrochemical performances of PEO-based electrolytes and determine the optimal addition amount.The results show that 15 wt% LTPO as filler could effectively lower the crystallinity of PEO and enhance the ionic conductivity of the SSE (4.61×10?4S/cm).Meanwhile, based on Lewis acid-base theory, the strong adsorption of LTPO powders on TFSI?promotes the release and convey of Li+, thereby enhancing the migration number of Li+in the SSE(tLi+=0.448).Moreover, by reason of the high strength and flame retardancy of the LTPO powders additive, the mechanical properties and thermal stability of the SSE are improved.The LiFePO4-ASSLMB assembled by PEO-LiTFSI-15 wt% LTPO CPE also displays remarkable rate performance and cycle performance.It has high specific capacities of 157.3, 152, 142.6, 105 and 53.1 mAh/g under 0.1, 0.2, 0.5, 1 and 2 C at 60°C.After 200 cycles at 0.5 C and 60°C,it still delivers an excellent discharge specific capacity of 128.4 mAh/g.Hence, LTPO as an active filler can effectively optimize the properties of SSEs, which opens a new way for the development of potential ASSLMBs with superior performance.

    Declaration of competing interest

    The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

    Acknowledgments

    This work was supported by the National Natural Science Foundation of China (NSFC, Nos.52073212, 51772205, 51772208), and the General Program of Municipal Natural Science Foundation of Tianjin (Nos.17JCYBJC17000, 17JCYBJC22700).

    Supplementary materials

    Supplementary material associated with this article can be found, in the online version, at doi:10.1016/j.cclet.2021.12.022.

    久久人人爽人人片av| 久久中文字幕一级| 在线观看免费午夜福利视频| 99热网站在线观看| 亚洲激情五月婷婷啪啪| 成人亚洲精品一区在线观看| 宅男免费午夜| tube8黄色片| 久久亚洲精品不卡| 亚洲第一青青草原| 中文字幕人妻丝袜一区二区| 黄色一级大片看看| 国产伦人伦偷精品视频| 男的添女的下面高潮视频| 亚洲欧美一区二区三区黑人| 母亲3免费完整高清在线观看| 超色免费av| 99热国产这里只有精品6| 爱豆传媒免费全集在线观看| 男男h啪啪无遮挡| 欧美亚洲日本最大视频资源| www.av在线官网国产| 一区二区三区精品91| 日韩中文字幕视频在线看片| 亚洲自偷自拍图片 自拍| 韩国精品一区二区三区| 中文字幕人妻丝袜制服| 国产97色在线日韩免费| 激情在线观看视频在线高清| 国产真人三级小视频在线观看| 亚洲九九香蕉| 久久久久国产一级毛片高清牌| 黑人操中国人逼视频| 老熟妇仑乱视频hdxx| 国产精品二区激情视频| 给我免费播放毛片高清在线观看| 欧美大码av| 婷婷精品国产亚洲av| 啦啦啦免费观看视频1| 久久中文字幕一级| 亚洲男人的天堂狠狠| 亚洲一区二区三区不卡视频| 国产精品久久久av美女十八| 99在线人妻在线中文字幕| 欧美性猛交黑人性爽| 免费搜索国产男女视频| 亚洲五月婷婷丁香| 亚洲 欧美一区二区三区| 午夜两性在线视频| 欧美久久黑人一区二区| 日本成人三级电影网站| 男女床上黄色一级片免费看| 青草久久国产| 中文字幕久久专区| 亚洲专区中文字幕在线| 香蕉av资源在线| www.999成人在线观看| 黄色女人牲交| 亚洲,欧美精品.| 国产一区二区在线av高清观看| 成在线人永久免费视频| 午夜亚洲福利在线播放| а√天堂www在线а√下载| 男女床上黄色一级片免费看| 美女高潮喷水抽搐中文字幕| 国产主播在线观看一区二区| 淫秽高清视频在线观看| 19禁男女啪啪无遮挡网站| 亚洲精品美女久久av网站| 国产av不卡久久| 欧美午夜高清在线| 日本精品一区二区三区蜜桃| 十八禁网站免费在线| av有码第一页| 韩国精品一区二区三区| 男女下面进入的视频免费午夜 | 一区二区三区国产精品乱码| 女人被狂操c到高潮| e午夜精品久久久久久久| 97超级碰碰碰精品色视频在线观看| √禁漫天堂资源中文www| 一卡2卡三卡四卡精品乱码亚洲| xxxwww97欧美| 无人区码免费观看不卡| 午夜老司机福利片| 99热6这里只有精品| 久久久精品国产亚洲av高清涩受| 男女那种视频在线观看| 国产1区2区3区精品| 国产精品香港三级国产av潘金莲| 久久久久久九九精品二区国产 | 国产高清videossex| 午夜老司机福利片| 午夜精品在线福利| 99在线视频只有这里精品首页| 精品午夜福利视频在线观看一区| 久久热在线av| 老司机深夜福利视频在线观看| 身体一侧抽搐| 久久国产精品男人的天堂亚洲| 久久天堂一区二区三区四区| 欧美性猛交╳xxx乱大交人| 日韩大码丰满熟妇| 欧美黄色淫秽网站| 两个人看的免费小视频| 日韩精品中文字幕看吧| 免费在线观看影片大全网站| 国内毛片毛片毛片毛片毛片| 高清在线国产一区| 色婷婷久久久亚洲欧美| 成人精品一区二区免费| 久久久久久久午夜电影| 欧美黑人精品巨大| 亚洲人成77777在线视频| 大香蕉久久成人网| 色av中文字幕| 国产成+人综合+亚洲专区| 大型黄色视频在线免费观看| 久久婷婷人人爽人人干人人爱| 美女高潮到喷水免费观看| 中国美女看黄片| 成年女人毛片免费观看观看9| 人妻丰满熟妇av一区二区三区| 国产精品乱码一区二三区的特点| 国产高清视频在线播放一区| 男女做爰动态图高潮gif福利片| 日本a在线网址| www.精华液| 精品少妇一区二区三区视频日本电影| 免费高清视频大片| 首页视频小说图片口味搜索| 亚洲五月色婷婷综合| 亚洲精品色激情综合| 国产极品粉嫩免费观看在线| 日韩精品中文字幕看吧| 亚洲精品粉嫩美女一区| 欧美黄色淫秽网站| 亚洲欧美精品综合一区二区三区| 美女大奶头视频| 国产精品一区二区三区四区久久 | 男人的好看免费观看在线视频 | 欧洲精品卡2卡3卡4卡5卡区| 亚洲性夜色夜夜综合| 19禁男女啪啪无遮挡网站| 久久中文字幕一级| 国产一区在线观看成人免费| 国产三级黄色录像| 动漫黄色视频在线观看| 精品高清国产在线一区| www国产在线视频色| 波多野结衣高清作品| 999久久久国产精品视频| 日本黄色视频三级网站网址| 成人国产综合亚洲| av电影中文网址| 在线观看免费视频日本深夜| 搡老岳熟女国产| 成人免费观看视频高清| 国产成人影院久久av| 欧美中文日本在线观看视频| 丁香六月欧美| 国产精品亚洲一级av第二区| 一级a爱片免费观看的视频| 精品久久久久久久毛片微露脸| 香蕉国产在线看| 黄色a级毛片大全视频| 丝袜在线中文字幕| 午夜免费观看网址| 欧美成人性av电影在线观看| 母亲3免费完整高清在线观看| 欧美日韩黄片免| ponron亚洲| 国产真人三级小视频在线观看| 波多野结衣av一区二区av| 男人舔奶头视频| 亚洲三区欧美一区| 久热这里只有精品99| 欧美日韩亚洲综合一区二区三区_| 亚洲五月婷婷丁香| 国产成人啪精品午夜网站| 一本综合久久免费| 此物有八面人人有两片| 18禁国产床啪视频网站| 亚洲精华国产精华精| 亚洲男人的天堂狠狠| 亚洲最大成人中文| 日本五十路高清| 成人国产一区最新在线观看| 此物有八面人人有两片| 午夜亚洲福利在线播放| 国产精品美女特级片免费视频播放器 | 中文字幕av电影在线播放| 亚洲欧美日韩无卡精品| 99riav亚洲国产免费| 成人精品一区二区免费| 宅男免费午夜| 可以免费在线观看a视频的电影网站| 在线观看66精品国产| 日韩欧美国产一区二区入口| 欧美日韩中文字幕国产精品一区二区三区| 中文字幕人妻熟女乱码| 成人欧美大片| 男人舔女人的私密视频| 精品久久久久久久毛片微露脸| 后天国语完整版免费观看| 欧洲精品卡2卡3卡4卡5卡区| 亚洲自偷自拍图片 自拍| 亚洲av成人不卡在线观看播放网| 国产一区二区激情短视频| 久久精品国产亚洲av高清一级| 极品教师在线免费播放| 欧美中文综合在线视频| 欧美丝袜亚洲另类 | 人人妻人人看人人澡| 亚洲精品国产一区二区精华液| 一本综合久久免费| 亚洲精品在线观看二区| 国产精品爽爽va在线观看网站 | 男男h啪啪无遮挡| 成人国产一区最新在线观看| av有码第一页| 国产成人av教育| 99国产精品99久久久久| 好男人电影高清在线观看| 午夜福利免费观看在线| 老司机午夜十八禁免费视频| 亚洲av成人一区二区三| 女人高潮潮喷娇喘18禁视频| 叶爱在线成人免费视频播放| 狂野欧美激情性xxxx| 成人国产综合亚洲| 亚洲精品久久成人aⅴ小说| 久99久视频精品免费| 搞女人的毛片| 欧美黑人欧美精品刺激| 国产单亲对白刺激| 亚洲av成人不卡在线观看播放网| 制服诱惑二区| 国产亚洲av高清不卡| 精品国产乱码久久久久久男人| 男女那种视频在线观看| 久久精品国产亚洲av香蕉五月| 美女 人体艺术 gogo| 黄色成人免费大全| 国产亚洲精品久久久久5区| 黄片播放在线免费| 国产主播在线观看一区二区| 久久精品国产99精品国产亚洲性色| 国产一区二区三区视频了| 大型av网站在线播放| 波多野结衣巨乳人妻| 草草在线视频免费看| 免费在线观看成人毛片| 国产一级毛片七仙女欲春2 | ponron亚洲| 久久天躁狠狠躁夜夜2o2o| 搡老熟女国产l中国老女人| 久久中文看片网| 免费看日本二区| 午夜视频精品福利| 桃红色精品国产亚洲av| 国产精品免费视频内射| 亚洲精品中文字幕一二三四区| 窝窝影院91人妻| 黄色女人牲交| 亚洲avbb在线观看| 天天躁狠狠躁夜夜躁狠狠躁| 女警被强在线播放| 日本在线视频免费播放| 无遮挡黄片免费观看| 久9热在线精品视频| 亚洲午夜精品一区,二区,三区| a级毛片a级免费在线| 两个人看的免费小视频| 婷婷六月久久综合丁香| 欧美黄色淫秽网站| 久久久久久九九精品二区国产 | 91大片在线观看| 在线视频色国产色| 非洲黑人性xxxx精品又粗又长| 一边摸一边做爽爽视频免费| 久久天躁狠狠躁夜夜2o2o| 麻豆一二三区av精品| 免费av毛片视频| 狂野欧美激情性xxxx| 天天躁夜夜躁狠狠躁躁| 在线观看日韩欧美| 亚洲国产高清在线一区二区三 | 好看av亚洲va欧美ⅴa在| 亚洲精品色激情综合| 亚洲国产中文字幕在线视频| 日韩 欧美 亚洲 中文字幕| 日本一区二区免费在线视频| 亚洲电影在线观看av| 男女之事视频高清在线观看| 9191精品国产免费久久| 日本精品一区二区三区蜜桃| √禁漫天堂资源中文www| 日韩成人在线观看一区二区三区| 国产区一区二久久| 波多野结衣高清无吗| 给我免费播放毛片高清在线观看| 侵犯人妻中文字幕一二三四区| 91成年电影在线观看| 精品一区二区三区av网在线观看| 久久精品国产清高在天天线| 亚洲欧洲精品一区二区精品久久久| 午夜福利欧美成人| 亚洲第一欧美日韩一区二区三区| 国产三级在线视频| 亚洲人成伊人成综合网2020| 精品一区二区三区视频在线观看免费| 99riav亚洲国产免费| 亚洲午夜精品一区,二区,三区| 国产精品精品国产色婷婷| 久久伊人香网站| 动漫黄色视频在线观看| 午夜亚洲福利在线播放| 高潮久久久久久久久久久不卡| 999久久久国产精品视频| 91av网站免费观看| 久久午夜综合久久蜜桃| 国产男靠女视频免费网站| 久久久久久久精品吃奶| 啦啦啦韩国在线观看视频| 午夜福利在线在线| 18禁裸乳无遮挡免费网站照片 | 久久欧美精品欧美久久欧美| 老鸭窝网址在线观看| 国产成人av激情在线播放| 99国产极品粉嫩在线观看| 啪啪无遮挡十八禁网站| 国产成人精品久久二区二区免费| 午夜福利欧美成人| 人人妻人人澡人人看| 国产精品国产高清国产av| 国产一卡二卡三卡精品| 亚洲成国产人片在线观看| av免费在线观看网站| 亚洲精品粉嫩美女一区| 成人精品一区二区免费| 天天添夜夜摸| 国产亚洲精品一区二区www| 国产一区二区三区在线臀色熟女| 91在线观看av| 免费观看人在逋| 国产精品亚洲美女久久久| 天天添夜夜摸| 一本大道久久a久久精品| 99国产综合亚洲精品| 国产亚洲精品av在线| 国产精品日韩av在线免费观看| 啦啦啦观看免费观看视频高清| 精品乱码久久久久久99久播| 亚洲欧美日韩高清在线视频| 天堂动漫精品| 一级毛片精品| 女性生殖器流出的白浆| 欧美日本视频| 国内毛片毛片毛片毛片毛片| 少妇熟女aⅴ在线视频| 免费女性裸体啪啪无遮挡网站| 亚洲专区字幕在线| 国产成人精品无人区| 亚洲国产精品合色在线| 亚洲精华国产精华精| 婷婷精品国产亚洲av| av超薄肉色丝袜交足视频| 欧美精品亚洲一区二区| 一级片免费观看大全| 老熟妇乱子伦视频在线观看| 51午夜福利影视在线观看| 亚洲专区字幕在线| 人成视频在线观看免费观看| 久久国产精品影院| 午夜福利视频1000在线观看| 亚洲一区二区三区色噜噜| 精品久久久久久久末码| 久久精品91蜜桃| 国产av又大| 少妇粗大呻吟视频| bbb黄色大片| 成人av一区二区三区在线看| 一进一出抽搐动态| 2021天堂中文幕一二区在线观 | 精品国产美女av久久久久小说| 午夜成年电影在线免费观看| 国产精品久久久人人做人人爽| 伦理电影免费视频| 亚洲熟妇中文字幕五十中出| 成人欧美大片| 国产精品av久久久久免费| 成人永久免费在线观看视频| 狠狠狠狠99中文字幕| 美女国产高潮福利片在线看| 欧美黑人巨大hd| 国产精品一区二区精品视频观看| 国产精华一区二区三区| 久久久久久人人人人人| 亚洲最大成人中文| 精品久久久久久成人av| 美女免费视频网站| 国产av一区在线观看免费| 亚洲激情在线av| 男女那种视频在线观看| 欧美日韩中文字幕国产精品一区二区三区| 日本在线视频免费播放| 日本精品一区二区三区蜜桃| 啦啦啦韩国在线观看视频| 成人免费观看视频高清| 老司机深夜福利视频在线观看| 满18在线观看网站| 一边摸一边做爽爽视频免费| 别揉我奶头~嗯~啊~动态视频| 亚洲 国产 在线| 免费在线观看亚洲国产| 美女午夜性视频免费| 美女扒开内裤让男人捅视频| 欧美午夜高清在线| 夜夜躁狠狠躁天天躁| 久久精品国产亚洲av香蕉五月| 十分钟在线观看高清视频www| 最近在线观看免费完整版| or卡值多少钱| 给我免费播放毛片高清在线观看| 又黄又爽又免费观看的视频| 男女床上黄色一级片免费看| 老司机午夜十八禁免费视频| 国产一区二区三区视频了| 99国产精品一区二区蜜桃av| 韩国av一区二区三区四区| 久久久久久大精品| 中文字幕久久专区| 丰满的人妻完整版| 久久久久国产一级毛片高清牌| 亚洲av日韩精品久久久久久密| 高清在线国产一区| 国产高清视频在线播放一区| 久久性视频一级片| 亚洲 欧美 日韩 在线 免费| 中出人妻视频一区二区| 欧美久久黑人一区二区| 亚洲国产精品sss在线观看| 欧美日韩一级在线毛片| 欧美日韩精品网址| 免费女性裸体啪啪无遮挡网站| 久久 成人 亚洲| 亚洲久久久国产精品| 国产高清videossex| 亚洲国产毛片av蜜桃av| 国产精品美女特级片免费视频播放器 | 成人av一区二区三区在线看| a在线观看视频网站| 色婷婷久久久亚洲欧美| 黑丝袜美女国产一区| 国产精品野战在线观看| 欧美激情 高清一区二区三区| 亚洲av电影不卡..在线观看| 此物有八面人人有两片| 久99久视频精品免费| 一二三四在线观看免费中文在| 狠狠狠狠99中文字幕| 无限看片的www在线观看| 亚洲精品美女久久av网站| 淫妇啪啪啪对白视频| 黄色女人牲交| 99热这里只有精品一区 | 一本一本综合久久| 在线观看66精品国产| 满18在线观看网站| 久久精品亚洲精品国产色婷小说| АⅤ资源中文在线天堂| xxx96com| 久久精品国产亚洲av香蕉五月| 狂野欧美激情性xxxx| 日本五十路高清| 国产成人一区二区三区免费视频网站| 亚洲国产欧美日韩在线播放| 给我免费播放毛片高清在线观看| 一边摸一边做爽爽视频免费| 午夜福利在线观看吧| 日韩精品中文字幕看吧| 51午夜福利影视在线观看| 亚洲专区字幕在线| 欧美性猛交╳xxx乱大交人| 男男h啪啪无遮挡| 女生性感内裤真人,穿戴方法视频| 国内精品久久久久精免费| 深夜精品福利| 亚洲人成网站高清观看| 免费av毛片视频| 国产av一区在线观看免费| 国产免费av片在线观看野外av| 成人18禁在线播放| 国内揄拍国产精品人妻在线 | 中文字幕精品免费在线观看视频| 又大又爽又粗| 午夜福利在线在线| 在线播放国产精品三级| 90打野战视频偷拍视频| 国产黄片美女视频| 18禁黄网站禁片午夜丰满| 亚洲国产精品sss在线观看| 成人18禁高潮啪啪吃奶动态图| 午夜福利免费观看在线| 国产精品1区2区在线观看.| 好男人在线观看高清免费视频 | 国产aⅴ精品一区二区三区波| 欧美激情极品国产一区二区三区| 又黄又爽又免费观看的视频| 麻豆成人午夜福利视频| 美女午夜性视频免费| 欧美一级a爱片免费观看看 | 成人国语在线视频| 精品乱码久久久久久99久播| 一本综合久久免费| 久久九九热精品免费| 亚洲成人精品中文字幕电影| 婷婷丁香在线五月| 在线天堂中文资源库| 欧美日韩瑟瑟在线播放| 香蕉国产在线看| 亚洲国产精品sss在线观看| 男女那种视频在线观看| 亚洲av日韩精品久久久久久密| 99久久99久久久精品蜜桃| 国产精品自产拍在线观看55亚洲| 欧美日本视频| 制服丝袜大香蕉在线| 国产精品乱码一区二三区的特点| 国产成人精品久久二区二区91| 美女国产高潮福利片在线看| 亚洲国产欧美一区二区综合| 精品福利观看| 久久亚洲真实| 欧美日韩精品网址| 午夜福利在线观看吧| 成人特级黄色片久久久久久久| 禁无遮挡网站| 在线观看www视频免费| 久久香蕉激情| 国产爱豆传媒在线观看 | 99久久综合精品五月天人人| 男人舔女人下体高潮全视频| 丰满人妻熟妇乱又伦精品不卡| 宅男免费午夜| 人妻丰满熟妇av一区二区三区| 老汉色av国产亚洲站长工具| 国产精品电影一区二区三区| av有码第一页| 欧美乱色亚洲激情| 日韩av在线大香蕉| 国产爱豆传媒在线观看 | 亚洲人成网站在线播放欧美日韩| 国内精品久久久久久久电影| 宅男免费午夜| 欧美 亚洲 国产 日韩一| 给我免费播放毛片高清在线观看| 18禁黄网站禁片免费观看直播| 国产99久久九九免费精品| 人成视频在线观看免费观看| www.自偷自拍.com| 黄色丝袜av网址大全| 俄罗斯特黄特色一大片| 欧美日韩黄片免| 亚洲av电影不卡..在线观看| 久久久国产精品麻豆| 国产精品亚洲一级av第二区| 欧美中文日本在线观看视频| 亚洲精品美女久久av网站| 老司机在亚洲福利影院| 国内精品久久久久久久电影| 亚洲av美国av| 岛国在线观看网站| 美女 人体艺术 gogo| 国产精品免费一区二区三区在线| 搡老熟女国产l中国老女人| 一本一本综合久久| 男女下面进入的视频免费午夜 | 长腿黑丝高跟| 国产乱人伦免费视频| 亚洲欧美激情综合另类| 99精品欧美一区二区三区四区| 超碰成人久久| 99精品久久久久人妻精品| 国内揄拍国产精品人妻在线 | 日韩三级视频一区二区三区| 手机成人av网站| 人人妻人人澡人人看| 国产精品免费一区二区三区在线| 欧美国产精品va在线观看不卡| bbb黄色大片| 亚洲第一青青草原| 久久久久国产精品人妻aⅴ院| 日韩有码中文字幕| 午夜福利一区二区在线看| 国产成+人综合+亚洲专区| 欧美日韩一级在线毛片| 亚洲激情在线av| 国产精品乱码一区二三区的特点| 18禁黄网站禁片午夜丰满| 亚洲成人国产一区在线观看| 欧美日韩瑟瑟在线播放| 免费在线观看亚洲国产| 十八禁网站免费在线| 黄色成人免费大全| 久久精品国产99精品国产亚洲性色| 女生性感内裤真人,穿戴方法视频| 麻豆成人av在线观看| 精品欧美一区二区三区在线| 午夜福利免费观看在线| 999久久久精品免费观看国产| 美女扒开内裤让男人捅视频| 99国产综合亚洲精品| 一进一出抽搐gif免费好疼|