• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Bifunctional carbon-based cathode catalysts for zinc-air battery: A review

    2022-06-18 03:00:10HuiminLiuQingleiLiuYrongWngYongfeiWngShuleiChouZhizhiHuZhiqingZhng
    Chinese Chemical Letters 2022年2期

    Huimin Liu, Qinglei Liu, Yrong Wng, Yongfei Wng,b,*, Shulei Chou, Zhizhi Hu,Zhiqing Zhng,*

    a Key Laboratory for Functional Material School of Chemical Engineering, University of Science and Technology Liaoning, Anshan 114051, China

    b School of Materials and Metallurgy, University of Science and Technology Liaoning, Anshan 114051, China

    c Institute for Carbon Neutralization, College of Chemistry and Materials Engineering,Wenzhou University, Wenzhou 325035, China

    ABSTRACT Efficient bifunctional OER/ORR catalysts are crucial for the further development of zinc-air battery.From a sustainable point of view, it is important that electrocatalysts are efficient, low cost, and composed of abundant resources instead of scarce metals.Due to their good conductivity, low cost, and strong durability, carbon-based materials are considered a promising alternative in the field of commercial zinc-air battery catalysts.Herein, we briefly introduce the zinc-air battery and then summarize recent progress in the development of carbon-based bifunctional catalysts by defect engineering, heteroatom doping and metal doping.Finally, we discuss the main challenges and prospects for the future development of carbon-based bifunctional oxygen catalysts.

    Keywords:Carbon materials Defect Doping, Oxygen evolution reaction Oxygen reduction reaction Zinc-air battery

    1.Introduction

    Due to the economic, scientific, and technological development over the past several decades, human society has made significant progress in many areas such as the chemical industry, environmental protection, medical treatment, electronics, and energy production.However, the consumption of nonrenewable energy has increased with global economic development.The emergence of clean solar and wind energy can solve many of the issues caused by this energy crisis.However, renewable energy output is greatly affected by season, climate, and location, and cannot be controlled as needed.Therefore, in order to effectively utilize solar energy and wind energy, the development of low-cost, sustainable, and highly efficient energy conversion and storage technologies is of utmost importance [1–4].Due to their high energy density, low cost, wide range of use, safety and reliability, zinc-air battery have broad commercialization prospects [5,6].

    The oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) are the basis for converting chemical energy into electrical energy.These reaction processes are complex and their kinetics is slow.Furthermore, their practical energy efficiency and cycle stability are far from satisfactory [7,8].Although Zn and O2can react spontaneously, the kinetics of ORR are slow in the process of battery discharge, requiring the participation of a catalyst to accelerate the reaction.Meanwhile, effective OER catalysts are also essential to realize rechargeable zinc-air battery.Currently, the best ORR catalyst is Pt, but the activity of Pt for OER is not satisfactory.RuO2and IrO2are the benchmark OER catalysts, but they have poor ORR performance.Although a combination of these two catalysts can achieve bifunctional catalysis, this results in a complex process and high price [9–11].Therefore, the design of effi-cient, stable, and low-cost bifunctional catalysts for both ORR and OER is urgently required.

    Recently, carbon-based materials, transition metal-based materials and their derivatives (oxides/sulfides/hydroxides), and composites have been extensively explored as alternative materials for bifunctional catalysts.Although transition metal-based catalysts have good redox electrochemical properties, their poor conductivity and dispersion limits their application.Carbon-based materials have various structures such as 0D (e.g., fullerene), 1D (e.g., carbon nanotubes (CNTs)), 2D (e.g., graphene) and 3D (porous carbon nanostructures) morphologies.These morphologies provide more exposed active sites and result in faster mass transfer.Moreover,due to their high conductivity, high specific surface area, good corrosion resistance, and low cost, carbon-based materials have aroused a significant amount of research interest [12–16].The free electrons in sp2carbon structures can ensure rapid charge transfer in redox reactions.In addition, their electronic structure can be easily adjusted by heteroatom doping, defect engineering, or in combination with other metals to improve catalytic performance.Although several reviews have summarized carbon-based materials as bifunctional electrocatalysts in zinc-air battery, it is necessary to provide an updated summary of the large amount of recent research in this area.

    Therefore, in this review, we first summarize the working principles of zinc-air battery and the related reaction mechanism of oxygen reactions.Subsequently, emerging carbon-based bifunctional electrocatalysts are presented, paying particular attention to changes to catalyst size and structure as well as new strategies for improving catalyst performance.These electrocatalysts are synthesized by defect engineering, heteroatom doping and metal doping.Finally, we describe the current challenges and future perspectives of carbon-based bifunctional oxygen catalysts for meeting the performance requirements of zinc-air battery.We expect that this review will provide timely information for future research and identify directions for the future development of electrocatalysts with high activity, a long life, and good performance in zinc-air battery.

    2.Electrically rechargeable zinc-air battery

    Zinc-air battery is a type of metal-air battery.This technology is relatively mature and was initially developed in the 19thcentury.In 1878, Maicheet al.used a porous carbon electrode containing platinum as a positive electrode to assemble the earliest zinc-air battery.The electrode performance of this battery was very poor because a slightly acidic electrolyte was used [17].In 1932, Heise and Schumacher used an alkaline electrolyte to prepare a zincair battery, significantly increasing the discharge current.However,output power was low [18].Since then, many countries around the world have developed and promoted zinc-air battery.Today,they are widely used in communication base stations, electric bicycles, seismic telemetry, energy storage, and electric vehicles [19–21].They have the advantages of high energy density, a stable electrolyte and low cost [22,23].

    2.1.Battery configuration

    Zinc-air battery use metal zinc as the anode, oxygen in the air or pure oxygen as the cathode, and are encapsulated with an electrolyte, as shown in Fig.1.Zinc electrodes are usually made of zinc powder, a zinc plate, or zinc foam.The most commonly used electrolytes in zinc-air battery are alkaline solutions such as KOH, NaOH and LiOH.Among these, KOH solution has been widely used because of its good conductivity, high mass transfer rate, and high zinc salt solubility [24–29].Generally, a small quantity of ZnCl2(e.g., 0.2 mol/L) is added to 6 mol/L KOH electrolyte to ensure the reversibility of the zinc electrochemical reactions [30,31].

    Fig.1.Basic Zn-air battery configuration and simplified solid-liquid-gas three-phase interaction.

    2.2.Operation principles

    The working principle of rechargeable zinc-air battery is that oxygen (the cathode) and metal zinc (the anode) undergo an electrochemical reaction in alkaline solution to recharge the battery.In other words, this process generates zinc oxide from elemental zinc and oxygen.In alkaline aqueous solution, the dissolution of the zinc electrode is divided into two steps.The first is the oxidation of zinc to zincate (Zn(OH)42-).The zinc oxide then precipitates when it is dissolved and saturated during the discharge process [32]:

    During the charging process, the reaction of the anode and cathode electrodes is completely reversible.The reduction reaction occurs in the zinc electrode.That is, Zn(OH)42-ions are reduced to elemental Zn.The air electrode provides an oxidation reaction to produce oxygen.Finally, ZnO decomposes into Zn and O2.

    Theoretically, the standard electromotive force of a zinc-air battery relative to a standard hydrogen electrode is 1.65 V.However, in actual operation, the actual discharge voltage is lower than 1.65 V due to the internal loss of the battery, resistance polarization, and concentration loss.The charging voltage must be higher than 1.65 V to complete the charging process and is decided by the current density and the performance of the air electrode catalyst.As discussed above, the discharging and charging processes correspond to the basic electrochemical reactions (ORR and OER)at the air cathode.The overpotential of the air cathode plays a key role in the charge and discharge voltage of the battery.In order to construct a rechargeable zinc-air battery with a high energy density and good cycle durability, the air (oxygen) electrode needs to have an efficient and stable bifunctional catalytic activity.This is because during both the charging and discharging processes, the overpotential of the electrode increases rapidly with enhancement of current density.Therefore, the development of an air electrode with highly efficient bifunctional catalytic performance is necessary to effectively promote the ORR and OER process.

    2.3.Reaction mechanism for ORR and OER

    OER and ORR are a pair of reversible reactions in electrochemical energy conversion equipment.They are the key to the future of zinc-air battery systems.However, slow dynamics and limited reversibility are the main obstacles that limit the efficiency of zincair battery [30,33].The ORR mechanism is very complex, involving a large number of intermediate products.Currently, it is generally accepted that the reaction process in alkaline solution proceeds according to the direct four-electron pathway (O2+ 2H2O + 4e-→4OH-) or the two-electron pathway (O2+ H2O + 2e-→HO2-+OH-, HO2-+ H2O + 2e-→3OH-) [34,35].

    When ORR follows the two-electron pathway, a large number of intermediate products (HO2-or H2O2) are produced.This reduces the efficiency of the reaction and leads to corrosion and deactivation of the catalyst, affecting the energy conversion rate and long-term life of the battery.When ORR follows the four-electron pathway, O2is directly reduced to H2O or OH-, which avoids corrosion of the catalyst and improves the energy conversion rate and cycle life of the battery [36].However, in practice, ORR is usually a mixed transfer reaction that includes both the two-electron and four-electron pathways.Therefore, finding a suitable catalyst to enhance the four-electron pathway is necessary for development of efficient zinc-air battery.

    The mechanism of OER is different and more complex than that of ORR.A large number of intermediate products are produced during a multi-step electron transfer process [37–39].Therefore, it is imperative to develop a catalyst that increases the OER reaction rate and reduces its activation energy.

    3.Bifunctional oxygen electrocatalysts

    At present, the precious metal-based catalysts Ru/IrO2and Pt/C demonstrate the best performance for OER and ORR, respectively.However, these catalysts are usually monofunctional.While a simple mixture of Ru/IrO2and Pt/C can be used as a bifunctional electrocatalyst, the complex preparation process, expensive material costs, and poor stability of precious metals significantly limit their development in zinc-air battery [40–42].Therefore, the design and development of cheap and stable non-precious metal catalysts have become a research hotspot.

    Carbon materials are an important catalyst for zinc-air battery, with the advantages of low cost, good stability, large specific surface, and high conductivity [43–46].In addition, their electronic structures can be easily modified by defect engineering, heteroatom doping, or combination with other substances to improve electrocatalytic performance [47–49].This paper will review the recent development of carbon-based materials as efficient and stable bifunctional electrocatalysts and outline future development directions.

    The activities of different reported catalysts are displayed in detail in Fig.2.The X-axis represents ORR activity at the halfwave potential (E1/2).Catalysts with higherE1/2values have better performance.The Y-axis represents OER activity when the current density is 10 mA/cm2(E10).LowerE10values mean better performance.As can be seen, transition metal doping can significantly improve the activity of bifunctional electrocatalysts.The activity of these catalysts mainly depends on the unsaturated coordination bond in the active center or changes to the microstructure caused by the metal atoms.However, since most transition metal-based catalysts rely on surface reactions, some metal atoms in these catalysts cannot contact the reactants, resulting in low metal atom utilization.Therefore, reducing the geometric size of catalyst particles can improve electrocatalytic performance.The preparation of homogeneous monoatomic catalysts to improve the utilization rate of each metal atom and increase the proportion of low coordination metal centers should be the focus of future research.

    Fig.2.Summary of electrocatalytic activity of recently reported bifunctional catalysts.

    3.1.Dopant-free carbon materials

    The electrocatalytic process takes place on the surface of the electrocatalyst.Therefore, designing and controlling the surface of electrocatalysts is a key factor in catalyst design.In addition to the intrinsic characteristics of carbon materials, a large number of early studies have shown that the surface defects of electrocatalysts such as impurity defects, vacancy defects, and interstitial defects have a positive effect on electrocatalytic performance (Fig.3) [50–52].

    Fig.3.Different carbon material defects.

    Recent reports on defective catalysts for oxygen electrodes are described below, as well as an analysis of how these defects affect electrocatalytic activity.Wanget al.used highly oriented pyrolytic graphite as an ORR catalyst and attempted to determine the active sites in the graphite [53].A schematic diagram of the ORR test performed at the designated location is shown in Figs.4a and b show that compared with the base plane, the edge has a higher onset potential and a larger current density.This is the first direct evidence that the edge of graphite is more active than the basal plane.To verify this hypothesis, they prepared graphite materials with more exposed edges by ball milling.Electrochemical tests confirmed that a higher number of exposed graphite edges results in better ORR electrocatalytic performance.At the same time, Huet al.also showed that defective carbon materials can improve electrocatalytic activity [54], providing guidance for edge/defect engineering to improve catalytic activity.

    Fig.4.(a) Schematic diagram of ORR test.(b) LSV curves of highly oriented pyrolytic graphite.Reprinted with permisison [53].Copyright 2014, Wiley-VCH.(c)Schematic diagram of the synthesis of edge-rich graphene by Ar plasma etching.(d)TEM images of Ar plasma-treated graphene.Reprinted with permisison [57].Copyright 2014, Wiley-VCH.

    With these findings, it is reasonable to claim that catalytic activity of the base surface of carbon materials is not as good as catalytic activity of the edge.This provides a clear direction for the design of highly efficient carbon-based electrocatalysts to replace existing commercial catalysts.In-depth research has been conducted on the design of defective carbon-based electrocatalysts.Daiet al.reported that the use of quantum dots carried by graphene nanoribbons reduced the size of carbon materials, exposing more edges/defects and demonstrating good electrocatalytic performance [55].Yaoet al.used a simple denitrification procedure to remove nitrogen from N-doped graphene, creating various carbon defects [56].Density functional theory (DFT) calculations revealed that the topological defects formed in the resulting bifunctional catalyst were the real active sites.

    Carbon materials can be prepared at high temperatures or with a template method to form more defect structures.However, these methods cannot control the generation of edge defects.With an understanding of the positive effect of edge defects on catalytic activity, the development of new methods to prepare carbon-based materials with a large number of exposed edges is very important.Tao and co-workers reported the first use of a plasma etching method for the development of graphene with rich defects as an efficient electrocatalyst.The sample preparation diagram for this method is shown in Fig.4c [57].This plasma etching method can control the generation of edge defects and be used to prepare carbon materials with more exposed edges.Transmission electron microscope (TEM) images (Fig.4d) clearly show that plasma treatment produces nano-sized holes but does not change the macroscopic structure of the graphene.This structure has an abundance of active sites and good conductivity.Electrochemical tests found that this material has significant electrocatalytic activity and good stability.Therefore, plasma technology is an effective method for controlling the formation of defects in carbon-based materials.This method shows significant promise for the treatment of other electrocatalysts in the future.

    The research discussed in this section has successfully demonstrated the important role of defects in improving the electrochemical performance of carbon-based materials.Although these prepared catalysts cannot yet replace commercial catalysts, the combination of heteroatom doping and edge effects shows great potential for the further improvement of catalyst performance.

    3.2.Heteroatom-doped carbon materials

    Many studies have shown that heteroatom doping can increase the number of catalytic active sites on carbon materials and improve catalytic activity.These improvements are caused by changes to the internal structure of the carbon and to the electron density distribution of carbon atoms adjacent to the doped heteroatoms[58–61].

    3.2.1.Mono-element doping

    Although carbon materials have a high surface area and good conductivity, the oxygen reduction process of pure carbon materials is dominated by the two-electron pathway, resulting in poor ORR activity.By intentionally introducing N, B, O, S, P or other heteroatoms to the carbon structure, the four-electron pathway can be promoted, significantly improving the ORR activity of the doped carbon materials.Among these elements, nitrogen-doped carbon materials have been the most widely studied for use as efficient bifunctional oxygen catalysts.Zhang’s team used a template method to prepare a defect-rich N-doped carbon material [62].High resolution transmission electron microscopy (HRTEM) shows that the catalyst prepared by this method possesses a large number of pore structures.This catalyst exhibits good electrochemical activity with higher current density and a more negative onset potential (Eonset).By calculating theE1/2andE10, the overall performance of the catalyst can be comprehensively judged.Fig.5a shows that this catalyst has a small potential difference, demonstrating good potential for application in zinc-air battery.A zinc-air battery with this catalyst as the air cathode demonstrates a high open circuit voltage, good stability, and the ability to power a 2.2 V LED light.Theoretical calculations (Figs.5b and c) show that the main reasons for improvement of catalyst performance are nitrogen doping, edge effects,and topological defects.These results have stimulated research on the reaction mechanism of catalysts and promoted the targeted design and manufacture of metal free carbon catalysts with defects for zinc-air battery.

    Nitrogen-substituted carbon materials include graphite nitrogen, pyridine nitrogen, and pyrrole nitrogen.Three forms with different proportions can be obtained by changing the nitrogen source, the temperature, and the synthesis method.Nevertheless,there is no definite conclusion about which form of nitrogen provides the largest enhancement to catalytic activity [63].Yanget al.prepared a highly reactive nitrogen-doped graphene catalyst by controlling the carbonization temperature [64].The zinc-air battery assembled with this catalyst has a high peak power density and specific capacity.It also demonstrates good cycle stability,and it was shown that the pyridine nitrogen structure plays the main catalytic role.Therefore, it can be concluded that the electrochemical performance of a catalyst is based on the effective design of catalyst structure.In turn, this is based on the introduction of defects and heteroatoms or adjustment of the geometric structure to increase the number of active sites and accelerate electron transfer.Wanget al.used a simple method to synthesize an excellent carbon material with a 3D structure rich in edge defects[65].The unique three-dimensional structure of the catalyst accelerates the rapid mass transfer process, which is considered to be one of the reasons for its excellent activity (Fig.5d).In addition, N doping in this carbon material leads to an increase in pyridine-N and graphite-N content, generating a large number of defects.It is known that N-doped edge defects redistribute charges and generate a charge difference, further enhancing electrochemical activity.Furthermore, a primary zinc-air battery assembled with this catalyst exhibits a high energy density and remarkable cycling stability(Figs.5e and f).This bifunctional carbon-based electrocatalyst with a low cost, simple synthesis method, and metal-free composition demonstrates excellent performance and great potential for zincair battery applications.

    In order to create more defects and increase the content of pyridine nitrogen, Yiet al.used a KMnO4etching method to prepare a nitrogen-doped carbon catalyst [66].The optimized material possesses a large number of defects and high level of pyridine-N content.It displays a significantly improved electrocatalytic activity and has the potential to replace commercial catalysts.In a zincair battery test, this nitrogen-doped carbon catalyst used as the air electrode demonstrated a similar energy density as Pt/C.To further explore the reaction mechanism, DFT calculations were performed to find that the active site is the second carbon close to pyridine-N.

    Overall, these results conclusively demonstrate that introducing heteroatoms to create more defects in carbon structures is one of the most important methods for improving the electrocatalytic activity of metal-free carbon materials.

    3.2.2.Multi-element doping

    Dual-atom doping strategies can provide a synergistic effect to further improve the dual-function electrocatalytic activity of metal-free carbon materials.Sunet al.prepared a porous carbon nanomaterial codoped with B and N by a simple precipitation method (Fig.6a) [67].This material exhibits excellent bifunctional electrocatalytic activity due to the formation of rich defects and heteroatom doping.It can be inferred from Fig.6b that the carbon material is rich in topological defects and edge defects.The hierarchical pore distribution is conducive to the diffusion of reactants and exposes more active sites.The difference in potential (ΔE) is an important parameter in evaluating the bifunctional catalytic activity of a catalyst (ΔE=E10(OER)-E1/2(ORR)).SmallerΔEvalues mean better electrocatalytic activity.As shown in Fig.6c, the prepared B,N-doped catalyst has a lowerΔEvalue compared with other non-noble metal catalysts reported in recent literature (ΔEB,N-codopedcarbon= 0.712 V;ΔEN-dopedcarbon= 0.90 V [62];ΔES,N-codopedcarbon= 0.77 V [68];ΔEP,N-codopedgraphene/carbon= 0.71 V [69]).This B,N-doped catalyst even had a lowerΔEvalue than commercial catalysts.Furthermore, the assembled primary zinc-air battery exhibits high cell efficiency and good long-term stability (Figs.6d and e).

    Fig.6.(a) Schematic diagram of B,N-codoped carbon.(b) N2 adsorption/desorption isotherm (inset: pore size distribution curve).(c) Overall LSV curve of catalysts.(d,e)Zn-air battery performance.Reprinted with permisison [67].Copyright 2018, Wiley-VCH.

    Multi-doped carbon materials have also been widely studied due to their potential synergistic effect.Wuet al.explored the influence of ternary doped materials as bifunctional catalysts.They successfully synthesized a N,F,P-codoped homogeneous carbon catalyst by electrospinning method [70], finding that the obtained porous 3D network structure accelerated the mass transfer process and increased the specific surface area.Furthermore, the doping of heteroatoms induced charge distribution.This catalyst exhibits good bifunctional catalytic activity.When assembled into batteries for testing, it shows great potential for primary zinc-air battery and rechargeable zinc-air battery applications.

    Although it has been shown that the doping of heteroatoms(B, F, P, S and N) into carbon materials can enhance catalytic activity, these doped catalysts have poor stability in harsh environments.Combining heteroatom-doped carbon materials with transition metals can solve this problem to a certain extent while also generating new active sites to further improve catalytic activity[71,72].

    3.3.Metallic doping of carbon materials

    Transition metals have high ORR and OER catalytic activity but poor oxidation resistance.However, studies have been reported showing that composites of transition metals and nitrogendoped carbon materials as ORR and OER bifunctional catalysts exhibit strong catalytic performance [73,74].To date, the nature of metal/nitrogen/carbon (M/N/C) active sites is still controversial.Some scholars believe that the active sites are the chemical bonds formed by nitrogen and transition metals.Others suggest that transition metals are not active sites, but that they promote the formation of N/C active sites at high temperatures.Although there is not yet good agreement on the nature of these active sites, related studies have shown that differences in the reaction conditions (nitrogen source, metal type and content, carbon support, carbonization temperature, and carbonization time) have a significant impact on catalytic activity [75–79].

    3.3.1.Metal nanoparticles

    Fe-N/C was the first M/N/C material to attract the attention of researchers in the field of zinc-air battery due to its excellent bifunctional catalytic performance.During the ORR/OER process,the inner metal centers of Fe-N/C are protected from corrosion by the alkaline solution and oxidative conditions, which is conducive to good durability [80–82].Wanget al.successfully synthesized high-density iron nanoparticles encapsulated in N-doped carbon nanoshells [83].This mesoporous catalyst has a relatively large specific surface area and pore volume, promoting the exposure of active sites during the electrochemical reaction.A catalyst prepared at 700 °C has a smallerΔEvalue, indicating that it has better electrochemical performance.After being assembled into a zincair battery, a maximum peak power density of 220 mW/cm2was reached at 0.72 V.This battery also demonstrates better chargedischarge performance and cycle durability compared with batteries based on Pt/C and IrO2catalysts.These results show that changing the iron precursor and the pyrolysis temperature can modify the nitrogen doping content and the surface area of the iron nanoparticles, allowing the design of an oxygen electrocatalyst with high catalytic activity and stability.In future research, further precise optimization of the structure and active sites of the catalyst may improve its performance.

    Parket al.prepared a novel Fe-N/C material by carbonizing filamentous materials containing carbon powder and an iron source at high temperatures for flexible rechargeable zinc-air battery applications.The battery assembled with this catalyst exhibits a higher power density [84].

    In addition to Fe-N/C, other M-N/C materials such as Co-N/C have been reported in recent years [85–87].The electrochemical performance of these catalysts can be further optimized by fine control of their morphology and microstructure.CNTs have hollow interiors and unique interwoven and macroporous properties which can significantly promote rapid electron transfer and the absorption of intermediates.Liet al.reported a Co,N-codoped carbon nanotube catalyst with excellent electrochemical performance which was constructed using a solution phase method [88].Based on the unique winding structure inside the nanotubes and the synergistic effect of N and Co, rapid electron transfer is significantly enhanced.This is one of the major reasons for its excellent catalytic activity.A zinc-air battery assembled with the prepared catalyst exhibited high specific capacity (675.8 mAh/g) and high peak power density (159.83 mW/cm2at 0.63 V).At the same time, it also showed excellent cycle stability, with only a slight drop in voltage after 150 h of charge-discharge cycles.

    Many studies have reported that metal organic frameworks(MOFs), which are three-dimensional porous materials with high specific surface area, high crystallinity, rich functional groups,and good structural stability, can simultaneously provide a carbon source, nitrogen source, and metal source for the synthesis of carbon-based catalysts.Therefore, MOFs are a hot material in the field of electrocatalysis [89-93].Among these materials, research on zeolite imidazolate frameworks (ZIFs) has been increasingly reported in recent years.For instance, Gadipelliet al.developed a simple and facile way to synthesize a high-performance Co-N/C bifunctional electrocatalyst by using ZIFs as a precursor [94].Zhanget al.successfully embedded Co particles into nitrogen-doped CNTs by pyrolysis of dicyandiamide and ZIF-67 [95].Zhouet al.used a novel tube template orientation method to grow ZIF-67in situon the surface of polypyrrole nanometers and prepare Co and N codoped carbon nanotubes as a bifunctional catalyst (Fig.7a) [90].It can be clearly observed from Fig.7b that the crystal lattice of 0.204 nm, which is attributed to the d space of Co (111) plane.This catalyst has high activity, high stability, and a power density of up to 149 mW/cm2in a zinc-air battery.After an aging test of 5000 cycles, its half-wave potential only decreases by 7 mV, demonstrating good cycle stability.

    Fig.7.(a) Illustration of the synthetic process for Co@N–CNTs catalysts.(b) HR-TEM image of Co@N–CNTs catalyst.Reprinted with permisison [90].Copyright 2020, Elsevier Ltd.(c) Schematic diagram of Co-N/C catalyst synthesis.(d) Polarization and power density curves of Co-N/C and Pt/C catalysts.Reprinted with permisison [96].Copyright 2020, Elsevier Ltd.(e) Schematic illustration of the synthesis of FeCo-N/-C catalysts.Free energy diagrams of (f) ORR and (g) OER processes on FeN4, CoN4 and FeCoN4.Reprinted with permission [89].Copyright 2020, Royal Society of Chemistry.

    The existence of defects can be used to significantly improve catalytic activity.Therefore, accurate control of the morphology and structure of catalysts is the key to future research.Zhuet al.prepared Co-N/C nanomaterials by pyrolysis of Co ions encapsulated in ZIFs.These nanomaterials exhibit excellent electrochemical activity (Fig.7c) [96].In addition, it can be clearly observed that there is a high concentration of defects in the edges of the disordered graphite carbon after pyrolysis, revealing more active sites.The addition of Co ions produces a hollow structure, which increases the specific surface area.The performance of a zincair battery was tested with these Co, N-codoped carbon materials catalysts as the cathode.The maximum power density reached 135 mW/cm2(Fig.7d).Almost no voltage loss was seen when the battery was discharged at 20 mA/cm2for 7 h, indicating that the battery has good cycle durability.The unique defects and rich hollow structure of this catalyst expose a large number of active sites, increase the surface area, and accelerate mass transfer, significantly enhancing catalytic activity.This explanation was confirmed by DFT calculations.

    Compared with monometallic M/N/C composite materials, a synergistic effect can be achieved by using bimetallic materials to effectively improve the catalytic performance for ORR/OER.Through further modification, the intrinsic electronic and surface structure of the host material can also be manipulated.For this purpose, Zhuet al.calcined a MOF-based FeNi compound with melamine to prepare NiFe@N codoped graphene catalysts with a layered structure.These catalysts display excellent ORR and OER activity [97].A zinc-air battery assembled with these catalysts is comparable to a commercial catalyst.However, while MOF-type materials have many advantages, they inevitably agglomerate during the pyrolysis process.Therefore, Duanet al.used glucosamine to encapsulate ZnCo-ZIF, followed by pyrolysis at 700 °C to successfully synthesize FeCo-N/C catalysts (Fig.7e) [89].In this MOF,Zn is very volatile at high temperatures, which improves the spatial dispersion of residual metals in the N–C matrix and significantly affects the composition and local nanostructure of the catalyst.The prepared catalysts have excellent bifunctional electrocatalytic activity.When used as an air cathode for a solid and liquid zinc-air battery, high peak power density and good cycle stability were achieved.The performance of this catalyst is better than that of commercial Pt/C + RuO2.DFT calculations show that FeCoN8is more active than FeCoN4, indicating that the synergistic effect of Co and Fe active sites can further improve electrocatalytic performance (Figs.7f and g).

    It is worth mentioning that metal-coordinated porphyrin molecules have been widely studied as cathode catalysts for zincair battery in recent years.These materials have many advantages,such as a stable coordination environment.Porphyrin ligands have redox activity, which promotes the multi-electron process.Furthermore, metal-coordinated porphyrins have a diverse range of structures [98–100].However, their applications are limited due to their low electron transfer efficiency.Thus, for their application in zinc-air battery, the combination of these molecular catalysts with MOFs and other materials has been explored [101].Loh and coworkers prepared a porphyrin-based MOF with Fe3+as the node,significantly accelerating the electron transfer process [102].Similarly, Lianget al.prepared MOF-supported Co porphyrins as a catalyst for oxygen electrocatalysis.When assembled into a zinc-air battery, it showed the same performance as a platinum-based material [103].

    3.3.2.Single-atom catalysts

    In order to reduce catalyst costs, reducing the size of metal nanoparticles to increase atom efficiency is an effective method that can also significantly enhance catalytic performance [104].The atom is the smallest particle that maintains the chemical properties of an element.Single-atom catalysts (SACs) have attracted a growing amount of interest.This is due to their unique unsaturated coordination structure, the quantum size effect, and strong atom-supported interactions which can induce stable monatomic active sites in electrocatalysts [105–110].However, due to the easy generation of nanoclusters or nanoparticles (NPs) through agglomeration, the design of SACs with dense dispersion is still a significant challenge.Therefore, the rational design of novel SACs with high activity, good selectivity, and good stability has attracted widespread attention.Researchers have focused on studying the structure-activity relationship of these catalysts at the atomic and molecular scales.

    Reported SACs synthesis methods include mass-selected softlanding, atomic layer deposition, coprecipitation, impregnation,MOF template, strong electrostatic, and photoreduction.Among these, the MOF template method has a significant advantage in the preparation of SACs due to its accurate control of the number of metal atoms and the structure of anchored complexes [111–119].Since MOF-5 was used to synthesize porous carbon in 2008,many examples of manufactured MOF-derived nanomaterials have been reported [120–122].For example, during the growth of ZIF-8,a monoatomic catalyst with excellent electrocatalytic performance,denoted Fe-Nx-C, was successfully synthesized by Hanet al.[123].A zinc-air battery assembled with this material demonstrated a long cycle life.

    Yanget al.successfully applied SACs to foldable solid zinc-air battery using a surfactant-assisted method [124].They prepared CoN4/N codoped graphitic catalysts by doping Co ions into the g-C3N4interlayer, finding that the atom-dispersed Co-Nxis a highly efficient catalytic active site.High-angle annular dark field scanning transmission electron microscopy (HAADF STEM) (Fig.8a) was used to show that Co is evenly distributed on the graphite sheet.The overpotential curves diagrams of CoN4/N codoped graphitic carbon and Co-NPs/N codoped graphitic carbon (Fig.8b) show that the catalyst composed of single Co atoms has better catalytic activity (ΔE= 0.74 V) than the catalyst composed of Co nanoparticles.In addition to traditional three-electrode electrochemical research,it has been reported that the application of CoN4/N codoped graphitic carbon as an air cathode catalyst also shows good performance in rechargeable liquid zinc-air battery and foldable solid zinc-air battery.The energy density of these batteries is high and they have a long service life (Figs.8c–f).These results are very promising for the application of single-atom catalysts in wearable flexible batteries, providing new ideas for the application of singleatom catalysts.

    Fig.8.(a) HAADF STEM image of CoN4/NG catalyst.(b) Overpotential curves for different catalysts.(c-f) Performance of Zn-air battery with CoN4/NG catalyst as the air electrode.Reprinted with permission [124].Copyright 2018, Elsevier Ltd.(g) Co K-edge XANES spectra of CoNi/NC catalysts.Free energy diagrams of (h) ORR and(i) OER processes on NC, Ni-N and Co-Ni-N.Reprinted with permission [128].Copyright 2020, Wiley-VCH.

    During the synthesis of SACs, heteroatoms (S, P and B) can be introduced into the carbon matrix and partial nitrogen atoms in the active sites of M-Nx can be replaced.The introduction of these heteroatoms breaks the electronic structure of the conventional active sites and can effectively enhance the electrocatalytic performance of SACs [125].For example, S and N doping causes uneven charge distribution in the carbon skeleton, leading to positively charged carbon atoms.This is beneficial for the adsorption of oxygen.P doping helps shrink the adsorption of*OH intermediates and changes the electronic structure of the metal center, endowing the catalyst with bifunctional activity and improving ORR/OER activity [126].Chenet al.prepared an electrocatalyst codoped with single iron atoms, nitrogen, sulfur, and phosphorus [127].Longdistance phosphorus and sulfur interactions and close coordination of the nitrogen and metal framework were used to achieve electronic modulation of the active center.The synthesized catalyst has excellent performance, and its hollow form accelerates the slow kinetics.In addition, it also has great potential in H2-air and zinc-air fuel cells.

    While SACs have shown good application prospects in recent years and has shown many remarkable achievements in the field of zinc-air battery, their further application still faces huge challenges.There are two main reasons for this.One, the relationship between the linear ratio of reaction intermediates and the adsorption energy is difficult to determine because it depends on the single-atom active sites of SACs.This leads to a fundamental limitation of catalytic efficiency [128–130].On the other hand, in order to avoid the aggregation of single metal atoms to form nanoparticles, the amount of metal supported on the catalyst has to be relatively low, resulting in a lower overall activity [131–134].

    The introduction of dual atom catalysts (DACs) as a further extension of the SACs family of materials can further enhance catalytic activity [135,136].The synergistic effect of the two metal atoms in DACs significantly improves the activity of these catalysts.The design of DACs provides new ideas for accurately controlling active sites at the atomic level and the rational design of bifunctional catalysts with multiple active sites and excellent performance.Inspired by this idea, Hanet al.prepared heteroatomdoped dual-metal single-atom catalysts by pyrolysis of dopaminecoated metal-organic frameworks [137].Due to the formation of a porous structure and the synergistic effect of the diatomic structure in the conductive carbon framework, the Co-Ni dispersed in the N-doped carbon materials has excellent bifunctional catalytic activity (ΔE= 0.81 V), and a zinc-air battery assembled with this catalyst has a charge-discharge efficiency and cycle life superior to similar materials and even to Pt/C and IrO2catalysts.Co K-edge Xray absorption near edge structure (XANES) curves (Fig.8g) show that the near edge absorption energy of SACs is high, which indicates that Co single atoms in SACs have a more positive charge.The structural advantage of bimetallic monoatomic catalysts is highlighted by DFT analysis (Figs.8h and i).To optimize the electrocatalytic performance of DACs, Liet al.prepared a two-sided electrocatalyst with atomically dispersed Co/Ni dual sites by introducing ZIF-67 [138].Through reasonable design and synthesis of the composition and structure of the catalyst, the resulting catalyst exhibits good oxygen reaction performance.Through DFT calculations, it was determined that the synergistic effect of the Co/Ni-N-C atomic bond and microstructure can improve both ORR and OER performance, laying a new foundation for the development of efficient dual-atom catalysts.

    At present, DACs research is still in an early stage, but compared with SACs, DACs show significantly enhanced catalytic activity under the synergistic effect of a high loading of two different metalatoms.However, current DACs research mainly focuses on ORR and CO2RR.This overview provides a guide for scholars to investigate DACs in future research.

    In order to provide readers with a more detailed description of the latest progress in this field, we have summarized the electrocatalytic activities of representative materials reported in recent years, shown in Table 1.A summary of carbon-based catalysts as air electrodes in zinc-air battery is reported in Table 2.As can be seen, single-atom catalysts show the most potential as bifunctional oxygen electrocatalysts for the practical application of zinc-air battery.

    Table 1Summary of electrocatalytic activities of recently reported bifunctional catalysts in 0.1 mol/L KOH.

    Table 2Summary of the performance of carbon-based catalysts as air electrodes in zinc-air battery.

    4.Summary and outlook

    Zinc-air battery have broad application prospects in renewable electricity storage and transformation, but their efficiency is seriously affected by poor ORR and OER activity.Therefore, the development of bifunctional oxygen catalysts with excellent electrocatalytic activity is required for their further development.At present, precious metal materials are the most effective catalysts for ORR/OER, but their high cost, poor bifunctional activity, and low stability greatly limit their development.Therefore, this review focuses on the recent research advances of carbon-based bifunctional oxygen catalysts including metal-free carbon materials and carbon-based transition metal materials as air cathodes for zinc-air battery.In general, single-atom catalysts are by far the most promising non-noble metal catalysts for zinc-air battery.By optimizing the size, morphology, and structure of these catalysts,we expect that their performance in zinc-air battery will soar to unprecedented heights.This review offers guidance for the design and synthesis of electrocatalysts.The future development of these carbon-based materials should focus on three main directions, shown in Fig.9 and described below:

    Fig.9.Future development directions of carbon-based catalysts for zinc-air battery.

    (1) Controlled synthesis of carbon-based materials.Currently, it has been shown that the existence of defects in electrocatalysts improves their performance, but it is very difficult to create desirable and effective defects in these carbon materials.The reasonable design and development of carbon-based porous materials (with precise control of the carbon micro/nanostructure) is a promising method for achieving good control of defects.Furthermore, the exploration of the synergistic effect of multiple components to combine the characteristics of different components and create active sites with a specific structure should be further explored.For metal/nitrogen/carbon catalysts, it is particularly important to control the structure evolution on the micro/nanoscale because most of these catalysts are prepared by high-temperature pyrolysis.

    (2) Advanced characterization of carbon-based materials.Due to the restrictions of micro/nanoscale analysis, it is difficult to directly and accurately determine the mechanism of these catalysts, so the nature of their active sites is still controversial.From this point of view, future research should explore new experimental methods and use advancedin situcharacterization techniques to identify the real active species and reveal the reaction process.This will be helpful for designing highly efficient electrocatalysts in practical applications.

    (3) Improving the density of active centers in SACs.SACs can significantly improve catalyst activity, but due to the inevitable agglomeration of metal atoms during the synthesis process as well as the limitations of low metal loading, the preparation of highly dispersed SACs with high metal loading is still a key challenge.Although the development of DACs has led to an improvement in the density of active sites and catalytic performance due to the synergistic effect of different metal atoms,these dual atom sites are easier to aggregate or alloy.Furthermore, it is difficult to accurately determine the metal proportion in DACs, which limits the full utilization of the synergistic effect between different metal atoms.In addition, it is also difficult to accurately identify the active sites of DACs.Therefore,designing strong metal-support interactions and more effective synthesis strategies to avoid agglomeration will be necessary for further development of SACs and DACs.

    In conclusion, these carbon-based materials require a significant amount of development before they will be able to replace precious metal catalysts in zinc-air battery.However, there is no doubt that single-atom catalysts will continue to be rapidly developed.It is expected that more efficient atomic electrocatalysts will be developed for zinc-air battery applications in the future.

    Declaration of competing interest

    The authors declare no conflict of interest.

    Acknowledgements

    We gratefully acknowledge the financial support from the National Natural Science Foundation of China (No.21601076) and the Natural Science Foundation of Liaoning Province (No.2019-ZD-0266).

    伊人久久精品亚洲午夜| 亚洲综合色惰| 日本成人三级电影网站| 婷婷亚洲欧美| 亚洲精华国产精华液的使用体验 | 国内精品久久久久精免费| 国产久久久一区二区三区| 中文字幕精品亚洲无线码一区| 国产精品精品国产色婷婷| 亚洲欧美成人综合另类久久久 | 赤兔流量卡办理| 国产爱豆传媒在线观看| 看黄色毛片网站| 久久人妻av系列| 禁无遮挡网站| 亚洲无线在线观看| 九九久久精品国产亚洲av麻豆| 中文字幕av成人在线电影| 欧美+日韩+精品| 在线播放国产精品三级| 国产淫片久久久久久久久| 亚洲七黄色美女视频| 国产精品国产三级国产av玫瑰| 自拍偷自拍亚洲精品老妇| 一进一出抽搐gif免费好疼| 国产爱豆传媒在线观看| 国产高清视频在线观看网站| 久久韩国三级中文字幕| 99久久人妻综合| 日韩成人伦理影院| 久久精品人妻少妇| 五月玫瑰六月丁香| 一级毛片我不卡| 99热全是精品| 免费一级毛片在线播放高清视频| 全区人妻精品视频| 国产伦精品一区二区三区视频9| 国产av不卡久久| 亚洲av第一区精品v没综合| 国内精品宾馆在线| 一本精品99久久精品77| 国产精品一区二区三区四区免费观看| 久久人人精品亚洲av| 男人舔女人下体高潮全视频| 只有这里有精品99| 91狼人影院| 99久国产av精品国产电影| 人妻少妇偷人精品九色| 六月丁香七月| 国产黄a三级三级三级人| 热99在线观看视频| 久久99蜜桃精品久久| 国产高清不卡午夜福利| 在线a可以看的网站| 成人特级黄色片久久久久久久| 美女大奶头视频| 色哟哟·www| 亚洲aⅴ乱码一区二区在线播放| 久久草成人影院| 美女被艹到高潮喷水动态| 黄色日韩在线| 日韩中字成人| 国模一区二区三区四区视频| 精品无人区乱码1区二区| 午夜福利成人在线免费观看| 18+在线观看网站| 欧美区成人在线视频| 久久99热这里只有精品18| 青青草视频在线视频观看| 久久久久网色| 亚洲精华国产精华液的使用体验 | 色综合站精品国产| 一级黄片播放器| 午夜精品一区二区三区免费看| 深夜a级毛片| 亚洲精品粉嫩美女一区| 午夜爱爱视频在线播放| 国产大屁股一区二区在线视频| 日韩国内少妇激情av| 国产av在哪里看| 九色成人免费人妻av| 能在线免费看毛片的网站| 91精品国产九色| 天堂网av新在线| 欧美一区二区精品小视频在线| 国产av在哪里看| 国产私拍福利视频在线观看| 亚洲高清免费不卡视频| 欧美高清性xxxxhd video| 国产精品不卡视频一区二区| 国产三级中文精品| 色综合站精品国产| 免费观看的影片在线观看| 亚洲图色成人| 婷婷精品国产亚洲av| 91av网一区二区| 亚洲综合色惰| 狂野欧美激情性xxxx在线观看| av卡一久久| 六月丁香七月| 老女人水多毛片| 婷婷亚洲欧美| 九九久久精品国产亚洲av麻豆| 亚洲aⅴ乱码一区二区在线播放| 国产视频内射| kizo精华| 日日啪夜夜撸| 国产精品精品国产色婷婷| 国产麻豆成人av免费视频| 乱码一卡2卡4卡精品| 国产精品国产高清国产av| 人人妻人人澡欧美一区二区| 久久久久久国产a免费观看| 毛片女人毛片| 高清在线视频一区二区三区 | 国产久久久一区二区三区| 中文资源天堂在线| 婷婷六月久久综合丁香| 亚洲精品影视一区二区三区av| 99久国产av精品| 国产精品乱码一区二三区的特点| 草草在线视频免费看| 日本av手机在线免费观看| 中文字幕精品亚洲无线码一区| 亚洲丝袜综合中文字幕| 亚洲电影在线观看av| 亚洲美女视频黄频| 好男人视频免费观看在线| 国产精品蜜桃在线观看 | 神马国产精品三级电影在线观看| a级毛片免费高清观看在线播放| 男人和女人高潮做爰伦理| 又爽又黄a免费视频| 色综合色国产| 亚洲欧美成人综合另类久久久 | 久久人人爽人人片av| 99精品在免费线老司机午夜| 精品人妻偷拍中文字幕| 亚洲精品国产成人久久av| 午夜爱爱视频在线播放| 在线播放无遮挡| 久久热精品热| 淫秽高清视频在线观看| 女人被狂操c到高潮| 免费一级毛片在线播放高清视频| 国产乱人视频| 我要搜黄色片| av在线老鸭窝| 国产免费一级a男人的天堂| 亚州av有码| 亚洲欧美清纯卡通| 国产色爽女视频免费观看| 天天躁夜夜躁狠狠久久av| 国产黄a三级三级三级人| 国产老妇伦熟女老妇高清| 十八禁国产超污无遮挡网站| 人妻夜夜爽99麻豆av| 哪里可以看免费的av片| 99九九线精品视频在线观看视频| 禁无遮挡网站| 桃色一区二区三区在线观看| 久久精品国产亚洲网站| 最近中文字幕高清免费大全6| 成年免费大片在线观看| 色综合色国产| 3wmmmm亚洲av在线观看| 亚洲婷婷狠狠爱综合网| 国产欧美日韩精品一区二区| 久久久午夜欧美精品| 丰满乱子伦码专区| 桃色一区二区三区在线观看| 人妻制服诱惑在线中文字幕| 日韩制服骚丝袜av| 美女cb高潮喷水在线观看| 日韩一区二区视频免费看| 日韩av不卡免费在线播放| 亚洲内射少妇av| 久久久久网色| 欧美日韩国产亚洲二区| 少妇被粗大猛烈的视频| 久久6这里有精品| 免费黄网站久久成人精品| 国产成人freesex在线| 欧美日韩在线观看h| 少妇裸体淫交视频免费看高清| 麻豆乱淫一区二区| 高清午夜精品一区二区三区 | 如何舔出高潮| 国产伦一二天堂av在线观看| 午夜a级毛片| 六月丁香七月| 国产av麻豆久久久久久久| 色哟哟哟哟哟哟| 床上黄色一级片| 国产成人aa在线观看| 中文字幕av在线有码专区| 亚洲精品日韩在线中文字幕 | 精品久久久久久成人av| 日本熟妇午夜| 久久中文看片网| 99久久精品国产国产毛片| 亚洲三级黄色毛片| 亚洲欧美日韩无卡精品| 欧美xxxx黑人xx丫x性爽| 99久久成人亚洲精品观看| 全区人妻精品视频| 久久久精品94久久精品| 亚洲精品456在线播放app| 国产精品乱码一区二三区的特点| 国产精品免费一区二区三区在线| 欧美成人a在线观看| 亚洲不卡免费看| 在线a可以看的网站| 精品午夜福利在线看| av女优亚洲男人天堂| 久久精品国产鲁丝片午夜精品| 三级男女做爰猛烈吃奶摸视频| 精品一区二区免费观看| 乱系列少妇在线播放| 免费av观看视频| 少妇人妻一区二区三区视频| 亚洲精品久久国产高清桃花| 99热这里只有是精品50| 2022亚洲国产成人精品| 日韩欧美精品免费久久| 亚洲三级黄色毛片| 国产午夜精品久久久久久一区二区三区| 欧美日韩乱码在线| 晚上一个人看的免费电影| 免费无遮挡裸体视频| 精品一区二区免费观看| 国产淫片久久久久久久久| 亚洲人成网站在线观看播放| 五月伊人婷婷丁香| 在线观看午夜福利视频| 99热这里只有是精品50| 欧美+亚洲+日韩+国产| 免费观看人在逋| 国产精品久久电影中文字幕| 亚洲电影在线观看av| 久久久久久久午夜电影| 亚洲成a人片在线一区二区| 国产成人freesex在线| 久久精品夜夜夜夜夜久久蜜豆| 国产成人影院久久av| 精品国内亚洲2022精品成人| 国产亚洲5aaaaa淫片| 日日干狠狠操夜夜爽| 亚洲国产精品国产精品| 在线天堂最新版资源| 久久人人爽人人爽人人片va| 91精品国产九色| 成人亚洲欧美一区二区av| 日韩三级伦理在线观看| av女优亚洲男人天堂| 国产伦理片在线播放av一区 | 一本久久精品| 看片在线看免费视频| 国产精品无大码| 少妇猛男粗大的猛烈进出视频 | 久久久午夜欧美精品| 偷拍熟女少妇极品色| 成人无遮挡网站| 精品国内亚洲2022精品成人| 男人舔女人下体高潮全视频| 久久午夜亚洲精品久久| 特级一级黄色大片| 久久久久久伊人网av| 国产精品一区www在线观看| 欧美潮喷喷水| 亚洲成人中文字幕在线播放| 春色校园在线视频观看| 国产亚洲精品av在线| 少妇被粗大猛烈的视频| 男人的好看免费观看在线视频| 中文字幕久久专区| 最好的美女福利视频网| 午夜免费激情av| 看片在线看免费视频| 村上凉子中文字幕在线| 国产精品久久久久久av不卡| 久久久欧美国产精品| 少妇丰满av| 亚洲精品久久国产高清桃花| 亚洲人成网站在线观看播放| 男女边吃奶边做爰视频| 99热这里只有精品一区| 日韩欧美 国产精品| 久久综合国产亚洲精品| 国产精品永久免费网站| 我的老师免费观看完整版| 国产一区二区亚洲精品在线观看| 精品久久久久久成人av| 亚洲av中文av极速乱| 99久久无色码亚洲精品果冻| 啦啦啦韩国在线观看视频| 欧美日韩在线观看h| 偷拍熟女少妇极品色| 人妻系列 视频| 国产一级毛片在线| 亚洲欧美成人精品一区二区| 男女做爰动态图高潮gif福利片| 午夜爱爱视频在线播放| 婷婷亚洲欧美| 亚洲国产欧美在线一区| 国产精品蜜桃在线观看 | 国产一区二区在线av高清观看| 啦啦啦啦在线视频资源| 国产高潮美女av| 搡老妇女老女人老熟妇| 午夜激情福利司机影院| 在线天堂最新版资源| 久久久精品欧美日韩精品| 高清毛片免费看| av.在线天堂| 我要搜黄色片| 中文字幕人妻熟人妻熟丝袜美| 日韩精品青青久久久久久| av卡一久久| 99热精品在线国产| 日日撸夜夜添| 女人被狂操c到高潮| 2022亚洲国产成人精品| 久久久国产成人免费| 日韩国内少妇激情av| 国产高清视频在线观看网站| 欧美丝袜亚洲另类| h日本视频在线播放| 久久久久久久午夜电影| 国内久久婷婷六月综合欲色啪| 亚洲精品日韩在线中文字幕 | 婷婷精品国产亚洲av| 亚洲精品粉嫩美女一区| 乱码一卡2卡4卡精品| 久久人人精品亚洲av| 日本欧美国产在线视频| 国产精品一区二区在线观看99 | 三级毛片av免费| 日本熟妇午夜| 狂野欧美激情性xxxx在线观看| 99久久成人亚洲精品观看| av在线观看视频网站免费| 成人无遮挡网站| 欧美日韩国产亚洲二区| 欧美精品国产亚洲| 欧美成人免费av一区二区三区| 成人毛片60女人毛片免费| 一级毛片久久久久久久久女| 国产又黄又爽又无遮挡在线| 18禁黄网站禁片免费观看直播| 国产精品嫩草影院av在线观看| 看十八女毛片水多多多| 国产精品女同一区二区软件| 99久久精品一区二区三区| 免费电影在线观看免费观看| 极品教师在线视频| 亚洲精品乱码久久久久久按摩| 国产人妻一区二区三区在| av天堂中文字幕网| 日韩成人av中文字幕在线观看| 高清毛片免费看| 亚洲欧美日韩东京热| 99热只有精品国产| 国产精品伦人一区二区| 久久久久久九九精品二区国产| av女优亚洲男人天堂| av天堂中文字幕网| 中国国产av一级| 久久久久久久久中文| 欧美日韩精品成人综合77777| 日本爱情动作片www.在线观看| 国产91av在线免费观看| 国产精品99久久久久久久久| 91午夜精品亚洲一区二区三区| 亚洲欧洲国产日韩| av卡一久久| 午夜福利成人在线免费观看| 免费看光身美女| 日本五十路高清| 99热网站在线观看| 在线观看美女被高潮喷水网站| 男人和女人高潮做爰伦理| 校园春色视频在线观看| 亚洲欧美日韩东京热| 亚洲精品日韩av片在线观看| 激情 狠狠 欧美| 国产淫片久久久久久久久| 国产日韩欧美在线精品| 亚洲人成网站在线播放欧美日韩| 色综合亚洲欧美另类图片| 亚洲va在线va天堂va国产| 亚洲国产精品国产精品| 亚洲第一区二区三区不卡| 色综合站精品国产| 国内精品久久久久精免费| 国产伦精品一区二区三区视频9| 又爽又黄无遮挡网站| 欧美一区二区精品小视频在线| 亚洲va在线va天堂va国产| 国产精品.久久久| 长腿黑丝高跟| 乱码一卡2卡4卡精品| 亚洲精品色激情综合| 久久精品国产亚洲av天美| 村上凉子中文字幕在线| 欧美xxxx性猛交bbbb| 午夜福利在线观看免费完整高清在 | 国产一区二区在线观看日韩| 成人一区二区视频在线观看| 亚洲自拍偷在线| 亚洲国产色片| 我的老师免费观看完整版| 最后的刺客免费高清国语| 国产探花极品一区二区| 亚洲无线在线观看| 99热精品在线国产| 国产精品一区二区三区四区久久| 色尼玛亚洲综合影院| 99久久久亚洲精品蜜臀av| 午夜激情欧美在线| 日韩欧美 国产精品| 一本久久精品| 欧美一区二区精品小视频在线| 亚洲最大成人手机在线| 亚洲性久久影院| 狠狠狠狠99中文字幕| 日韩在线高清观看一区二区三区| 久久精品国产清高在天天线| 国产亚洲欧美98| 看片在线看免费视频| 日韩一本色道免费dvd| 99在线人妻在线中文字幕| 男人的好看免费观看在线视频| 国产精品一二三区在线看| 国产午夜精品论理片| 亚洲精品久久久久久婷婷小说 | 老司机福利观看| 亚洲国产日韩欧美精品在线观看| 此物有八面人人有两片| 日本av手机在线免费观看| 女人被狂操c到高潮| 黄色一级大片看看| 久久99热这里只有精品18| 插阴视频在线观看视频| 国产大屁股一区二区在线视频| 国产极品精品免费视频能看的| 欧美一区二区国产精品久久精品| 男女下面进入的视频免费午夜| 午夜免费激情av| 免费av观看视频| 中文字幕av成人在线电影| 久久久久久久久久黄片| 欧美色视频一区免费| 成人综合一区亚洲| 你懂的网址亚洲精品在线观看 | 村上凉子中文字幕在线| 麻豆乱淫一区二区| 人体艺术视频欧美日本| 嫩草影院入口| 一个人看的www免费观看视频| 亚洲av一区综合| 国产伦精品一区二区三区四那| 丰满人妻一区二区三区视频av| 亚洲av电影不卡..在线观看| 91aial.com中文字幕在线观看| 最近手机中文字幕大全| 欧美区成人在线视频| 欧美在线一区亚洲| 欧美激情久久久久久爽电影| 我要看日韩黄色一级片| 亚洲欧美成人精品一区二区| 一边亲一边摸免费视频| 国产精品野战在线观看| 国产精品一区二区三区四区久久| 蜜桃久久精品国产亚洲av| 菩萨蛮人人尽说江南好唐韦庄 | 99久久中文字幕三级久久日本| 亚洲国产精品国产精品| 久久精品夜夜夜夜夜久久蜜豆| 国产精华一区二区三区| 亚洲丝袜综合中文字幕| 国产成人91sexporn| 少妇人妻精品综合一区二区 | 亚洲国产精品合色在线| 亚洲精品粉嫩美女一区| 亚洲欧美成人精品一区二区| 69人妻影院| 特级一级黄色大片| 成人午夜高清在线视频| 人体艺术视频欧美日本| 久久久国产成人免费| 波多野结衣高清无吗| 久久精品国产99精品国产亚洲性色| 成人三级黄色视频| 91精品国产九色| 国产高潮美女av| 欧美在线一区亚洲| 看免费成人av毛片| 岛国在线免费视频观看| 日韩一区二区视频免费看| 亚洲熟妇中文字幕五十中出| 欧美成人免费av一区二区三区| 欧美日本亚洲视频在线播放| 一进一出抽搐动态| 日本黄色视频三级网站网址| 一级二级三级毛片免费看| 午夜精品一区二区三区免费看| 男人舔女人下体高潮全视频| 嘟嘟电影网在线观看| 亚洲精品久久久久久婷婷小说 | 成人毛片60女人毛片免费| 天天躁日日操中文字幕| 欧美不卡视频在线免费观看| 狠狠狠狠99中文字幕| 在线国产一区二区在线| 嫩草影院精品99| 少妇的逼水好多| 国产精品,欧美在线| 久久精品国产亚洲av天美| 一区福利在线观看| 男人狂女人下面高潮的视频| 亚洲自拍偷在线| 成年免费大片在线观看| 人人妻人人澡欧美一区二区| 国产中年淑女户外野战色| 99视频精品全部免费 在线| 好男人视频免费观看在线| 婷婷精品国产亚洲av| а√天堂www在线а√下载| 欧美人与善性xxx| 久久精品影院6| 国产 一区 欧美 日韩| av免费观看日本| 亚洲一区高清亚洲精品| 久久欧美精品欧美久久欧美| 国产麻豆成人av免费视频| 久久久久久九九精品二区国产| 男人的好看免费观看在线视频| 国产精品乱码一区二三区的特点| 免费观看人在逋| 日韩成人伦理影院| 久久精品国产清高在天天线| 一级av片app| 国产极品天堂在线| 免费在线观看成人毛片| 亚洲av中文av极速乱| 99热这里只有是精品在线观看| av天堂在线播放| 久久精品久久久久久久性| 在线观看av片永久免费下载| 成人性生交大片免费视频hd| 国产高潮美女av| 狂野欧美白嫩少妇大欣赏| 日产精品乱码卡一卡2卡三| 91精品国产九色| 久久婷婷人人爽人人干人人爱| 十八禁国产超污无遮挡网站| 国产精品三级大全| 久久久久免费精品人妻一区二区| 狠狠狠狠99中文字幕| 黄色日韩在线| 精品欧美国产一区二区三| 久久热精品热| 在线免费十八禁| 亚洲精品久久久久久婷婷小说 | 一区二区三区四区激情视频 | 少妇的逼好多水| 色尼玛亚洲综合影院| 成人三级黄色视频| 亚洲成人久久爱视频| 欧美日韩综合久久久久久| 亚洲精品国产成人久久av| 国产精品野战在线观看| 国产精品精品国产色婷婷| 国产精品国产高清国产av| 男插女下体视频免费在线播放| 中文字幕av成人在线电影| 婷婷色av中文字幕| 久久婷婷人人爽人人干人人爱| 亚洲在线观看片| 丰满乱子伦码专区| 国产免费男女视频| 午夜福利在线观看吧| 99久久久亚洲精品蜜臀av| 欧美丝袜亚洲另类| 一进一出抽搐gif免费好疼| 国产亚洲欧美98| 日韩制服骚丝袜av| 真实男女啪啪啪动态图| 久久久成人免费电影| 啦啦啦观看免费观看视频高清| 国产精品精品国产色婷婷| 亚洲色图av天堂| 亚洲欧美中文字幕日韩二区| 神马国产精品三级电影在线观看| 成熟少妇高潮喷水视频| 爱豆传媒免费全集在线观看| 亚洲精华国产精华液的使用体验 | 亚洲国产精品国产精品| 自拍偷自拍亚洲精品老妇| 狂野欧美白嫩少妇大欣赏| 亚洲一区二区三区色噜噜| 成人无遮挡网站| 波野结衣二区三区在线| 亚洲av二区三区四区| 给我免费播放毛片高清在线观看| 国产三级中文精品| 午夜精品国产一区二区电影 | 国产欧美日韩精品一区二区| 亚洲熟妇中文字幕五十中出| 亚洲av成人精品一区久久| 免费观看a级毛片全部| 亚洲人与动物交配视频| av在线蜜桃| 91久久精品国产一区二区三区|