• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Synthesis of vertical graphene nanowalls by cracking n-dodecane using RF inductivelycoupled plasma-enhanced chemical vapor deposition

    2020-03-09 13:22:24JiagengZHENG鄭佳庚QinhuaiTAN譚欽懷HangCHEN陳航AngjianWU吳昂鍵XiaodongLI李曉東JianhuaYAN嚴建華JiaxuDAI戴佳栩andJiaoZHOU周嬌
    Plasma Science and Technology 2020年2期
    關鍵詞:李曉東建華

    Jiageng ZHENG (鄭佳庚), Qinhuai TAN (譚欽懷), Hang CHEN (陳航),Angjian WU (吳昂鍵),3, Xiaodong LI (李曉東),3, Jianhua YAN (嚴建華),Jiaxu DAI (戴佳栩) and Jiao ZHOU (周嬌)

    1 State Key Laboratory of Clean Energy Utilization, Institute for Thermal Power Engineering, Zhejiang University, Hangzhou 310027, People’s Republic of China

    2 China United Engineering Corporation Limited, Hangzhou 310000, People’s Republic of China

    Abstract A facile and controllable one-step method to treat liquid hydrocarbons and synthesize vertical graphene nanowalls has been developed by using the technique of inductively-coupled plasmaenhanced chemical vapor deposition for plasma cracking of n-dodecane.Herein,the morphology and microstructure of solid carbon material and graphene nanowalls are characterized in terms of different operating conditions, i.e. input power, H2/Ar ratio, injection rate and reaction temperature. The results reveal that the optimal operating conditions were 500 W, 5:10,30 μl min?1 and 800°C for the input power,H2/Ar ratio,injection rate and reaction temperature,respectively. In addition, the degree of graphitization and the gaseous product are analyzed by Raman spectroscopy and gas chromatography detection. It can be calculated from the Raman spectrum that the relative intensity of ID/IG is approximately 1.55,and I2D/IG is approximately 0.48, indicating that the graphene prepared from n-dodecane has a rich defect structure and a high degree of graphitization. By calculating the mass loading and detecting the outlet gas, we find that the cracking rate of n-dodecane is only 6%-7%and that the gaseous products below C2 mainly include CH4,C2H2,C2H4,C2H6 and H2.Among them,the proportion of hydrogen in the outlet gas of n-dodecane cracking ranges from 1.3%-15.1% under different hydrogen flows.Based on our research, we propose a brand new perspective for both liquid hydrocarbon treatment and other value-added product syntheses.

    Keywords: ICPECVD, n-dodecane cracking, vertical graphene nanowalls

    1. Introduction

    N-dodecane(C12H26),a liquid hydrocarbon,is described as a special liquid waste with a high carbon content after it is effectively utilized. Nevertheless, in the absence of thorough disposal, n-dodecane may cause serious environmental pollution due to its high diffusivity,wide pollution range and large secondary toxicity. For this reason, developing an environmentally friendly way to dispose of n-dodecane has sparked great interest for society.

    Figure 1.Graphical abstract of the system to treat n-dodecane and synthesize VGs.

    Recent investigations for the disposal of liquid hydrocarbon waste mainly consist of physical methods and chemical methods. For instance, Osmanlioglu et al introduced a way of absorbing radioactive liquid hydrocarbon waste by using natural zeolite, and a decontamination factor of 430 was achieved under optimum conditions [1]. In addition,the chemical method put more emphasis on the reforming process of the liquid hydrocarbons to obtain hydrogen,micromolecular gaseous hydrocarbons or carbon materials.Gould et al systematically studied autothermal reforming of n-dodecane with different ratios of O/C and H2O/C over nickel-based catalysts and obtained various proportions of CO, CO2and H2syngas [2]. However, the current technologies for the disposal of liquid hydrocarbon waste mentioned above have many disadvantages such as high energy consumption, incomplete treatment, secondary pollution and the need for sophisticated facilities.

    With respect to the issues above, considerable effort has been devoted to improve the performance of the reforming process by reducing the energy consumption of the plasma process. Therefore, different types of non-thermal plasma technology,such as gliding arc plasma[3,4],glow discharge[5-7], microwave plasma [8, 9], RF plasma [10, 11], dielectric barrier discharge [12, 13], corona discharge [14, 15],plasma jet [16, 17] and spark [18, 19] offer attractive alternatives to the conventional catalytic process for activating low-value and inert molecules into clean fuels and highervalue chemicals at atmospheric pressure and low temperatures[20-22]. In the meantime, a lot of competitive plasma-based methods for the reforming of n-dodecane at ambient conditions have been investigated. Mochtar et al investigated the effect of gas flow rate on the gas production rate from n-dodecane using steam reforming in-liquid plasma and the maximum hydrogen generation efficiency was obtained up to 59% [23]. Ma et al investigated the plasma reforming of n-dodecane for the co-generation of COx-free hydrogen and C2hydrocarbons in a gliding arc discharge reactor and achieved the highest selectivities of H2(76.7%), C2H2(41.4%) and C2H4(12.0%) with n-dodecane conversion of 68.1% [24]. Among various plasma sources, however,inductively-coupled plasma (ICP) reveals an impressive function in both graphene fabrication and liquid hydrocarbon treatment due to its own high plasma density and the generation of abundant active species (ions, excited molecules,radicals and photons) [25].

    Herein, we propose a facile and controllable one-step method to treat liquid hydrocarbons and synthesize vertical graphene nanowalls (VGs) by using inductively-coupled plasma-enhanced chemical vapor deposition (ICPECVD).Our experimental system differs from other treatment processes in that it provides a new way to treat n-dodecane,which is catalyst-free and under relatively mild conditions.Moreover, this approach can obtain high-value graphene,which could be widely used in various fields.Compared with our previous study, we first propose the strategy of using the ICPECVD technique to treat liquid hydrocarbons. In the present paper, the morphological, spectral and electrical parameters of graphene growth are investigated. First, the influence of different operating conditions (applied power,gas proportion, injection rate and reaction temperature) on electrical parameters is analyzed to determine the optimal operating conditions for VG growth.In addition,the effect of operating conditions on the properties of the solid products is investigated by scanning electron microscopy (SEM) and Raman spectroscopy. The results demonstrate the morphology of graphene under different conditions along with the degree of graphitization of graphene. Gaseous products have been thoroughly investigated to explore the generation mechanism of all free radicals.Based on these investigations,we expect to advance our understanding of graphene fabrication. Furthermore, this understanding may provide a brand new way to develop a feasible and controllable synthesis approach for diverse applications.

    2. Experiment and methods

    In our experiment,the main plasma reactor is a combined ICP generator and CVD reactor.A schematic diagram is shown in figure 1. A cylindrical configuration comprises a quartz tube(48 mm in diameter and 1000 mm in length)and is fixed on a furnace.One end of the quartz tube is surrounded by a copper coil to cool the quartz tube to prevent tube overheating.

    For the experimental setup,plasma is stimulated by a RF power generator (Kmate, HERO-500 W, 13.56 MHz) and regulated by a matching box.Ni foam is used as the substrate for graphene growth in this experiment and was washed thoroughly with ethanol and deionized water before use. The carrier gas (Ar and H2) is adjusted by a mass flow controller(Seven Star D07). A rotary pump (KYKY, RVP-2) was applied to maintain a low-pressure atmosphere(0.1-0.5 torr),which is vital to ICP generation.In addition,n-dodecane was injected into the quartz tube inlet by a syringe pump(LONGER, LSP01-1A).

    At the beginning of the process,the Ni foam is anchored in a quartz boat, and then placed in the quartz tube. Air is evacuated by the rotary pump after the quartz tube is completely sealed. The heating device starts to run according to the setting program along with the aeration of the carrier gas.The plasma is generated when the temperature reaches the setting value.In the meantime,the n-dodecane is injected into the quartz tube inlet by the syringe pump and the gaseous products are collected at the exhaust by a gas bag. Ten minutes is most appropriate for the whole treatment time according to our previous study.

    In the detection section,gaseous products are tested by a gas chromatograph (GC9790A, Fuli Analytical Instrument Co., Ltd). Hydrogen is measured by a thermal conductivity detector and the gaseous products below C2(CH4, C2H2,C2H4and C2H6) can be detected by a flame ionization detector.

    The prepared graphene nanowall structure and morphology are further characterized via SEM (Ultral 55) and Raman spectroscopy (Labor Raman Series, HR-800, 514 nm laser).

    3. Result and discussions

    3.1. Characterization of thermal and electrical properties in n-dodecane cracking

    3.1.1. Effects of the applied power input. As a source of energy in this process, plasma could provide a huge number of high-energy electrons to collide with gas molecules. The probability that n-dodecane obtains energy by collision and cracks into small molecules or active groups will increase when the applied power input of the plasma increases,which means high electron density has been achieved. The active groups can also provide a rich raw material for the growth of the carbon material on the catalyst substrate. In addition, the higher the applied input power is, the higher the energy conversion efficiency, and both high-density electrons and active groups are helpful in enhancing the degree of graphitization and the growth area of the carbon material.For this reason, the applied input power has a significant influence on n-dodecane cracking and carbon material growth on Ni foam.

    Figure 2 illustrates the morphology of the synthesized graphene nanowalls with increasing applied input power. As shown in figure 2(a), no visible vertical graphene nanowalls are observed with the 300 W applied input power. Instead, a flattened ‘totem-like’ dot-line distribution can be seen. The lines are connected to each other and terminate at some dot positions. On the macro level,the dot-line structure is evenly distributed on the surface of the Ni substrate. It is confirmed that a large amount of carbon nanowires formed on the Ni substrate by the deposition of the carbon atoms. The dots observed may be the nucleation points for the growth of the graphene nanowalls. The above observations indicate that there is not enough raw material available for the selfrecombination of carbon atoms in these conditions, and most n-dodecane molecules are not excited into active groups. In addition, because the system temperature is maintained at 800°C, a large amount of long hydrocarbon chains will not accumulate on the surface of the Ni foam.

    When the applied input power is increased to 400 W, it can be observed that the carbon structure on the surface of the Ni foam begins to change. The original dot-line structure begins to grow in the vertical direction and has a morphology similar to graphene, indicating that the active groups exist in the reaction region. In the partially enlarged view of figure 2(c), it can be observed that the length of the carbon material with this structure is approximately 50-100 nm, and the thickness is wider than that with 300 W.

    When the applied input power reaches the maximum value of 500 W in the experimental system, as shown in figures 2(e) and (f), the structure of the graphene becomes relatively regular in both length and width. Its lateral dimension increases to between 500 nm and 1 μm, while the thickness of the graphene nanowalls is relatively thin.Compared with the dense distribution at 400 W, more cavity structures are formed between the graphene nanowall layers.It is believed that graphene nanowalls with relatively high thickness have superior electrical properties.

    3.1.2. Effect of hydrogen/argon ratio. Similarly, the proportion of the reaction atmosphere is also critical for the growth of graphene nanowalls.Ar is a shielding gas that also collides with electrons in the plasma region,and the Ar atoms in the excited state will continue to collide with other particles to absorb energy, while also transmitting energy. H2will directly affect the growth and morphology of graphene in two ways: one, H2collides with the n-dodecane molecule in the plasma region and then produces CnHx(especially CHx),which is an important raw material for the formation of graphene nanowalls;the other effect is that the hybrid carbon,thicker carbon layers and amorphous carbon can be etched by the H radicals coming from H2cracking. Therefore, H2has a certain effect on the defect structure modification of the graphene nanowall layers to obtain highly graphitized graphene nanowalls.

    Figures 3(a)-(c)show the carbon material structure when the flow rate of H2is 5 sccm and the flow rates of Ar are 5,10 and 20 sccm, respectively. As the flow rate of Ar increases,the carbon material on the surface of the Ni foam gradually changes from some nucleation points with a sparse distribution of carbon to many graphene nanowall layers of a certain scale, and finally to dense agglomerations of carbon particles on the surface. First, the relationship between absorption energy and transfer energy of Ar radicals is balanced in the process of n-dodecane cracking. When the Ar flow rate is 5 sccm,a large number of nucleation sites are distributed on the Ni substrate, but no nanowall structure appears. The above observation indicates that the component density to form graphene is not enough with a 5 sccm Ar flow. However, Ar with a low flow rate corresponds to a higher average input energy of n-dodecane molecules.This result indicates that Ar has an important effect on energy transfer and cracking promotion during the n-dodecane cracking process. This effect may occur because the high-energy electrons are not sufficient to directly motivate the n-dodecane,which requires Ar and H2as a medium.When the flow rate of Ar increases to 20 sccm,it is observed that the graphene nanowall structure is polycondensed into nanocarbon particles, the scale of which is much smaller than graphene. On the one hand, it can be considered that the energy absorption effect of Ar at this time is stronger than the energy transfer effect, the stronger absorption effect leads to the incomplete decomposition of n-dodecane and a large number of active groups of C3-C6,which are formed by the attraction of unsaturated bonds at the nucleation point. On the other hand, the reduction of energy causes the increase of surface stress on the carbon material,presenting a spherical structure. There are not enough H radicals to etch it at this time,so the carbon material stacks as the particle layers shown in figure 3(c).

    Figures 3(b) and (d) reveal graphene nanowall structure at H2flow rates of 5 and 10 sccm.Among them,the position of the red circle in figure 3(b) can be observed as a hybrid carbon structure, which is due to the different ways of bonding available to the carbon atoms in the graphene. To obtain graphene with a higher degree of graphitization,it can be etched by H2, and by comparing the above two results,increasing the H2flow rate can effectively reduce the complex and dense stacked carbon structure in graphene nanowalls and obtain a more crystalline carbon structure. Therefore, we can conclude that the energy distribution and species of reactive groups in the plasma region can be regulated to an optimum condition by controlling the proper flow rate and ratio of hydrogen/argon, which plays a crucial role in the formation of graphene nanowall structures.

    Figure 2.SEM images of carbon materials prepared at different applied powers for 10 min:(a),(b)300 W;(c),(d)400 W;(e),(f)500 W(H2/Ar = 5:10, 30 μl min?1, 800°C).

    3.1.3. Effect of the injection rate of n-dodecane. Under the synergistic effect of ICP and high-temperature heating,n-dodecane molecules will be cleaved into free radicals such as CH,H,CH2,CH3and C2.The C2is currently considered as the most important raw material in the growth process of graphene nanowalls due to its olefinic structure. However,compared with the cracking of methane, more C3-n(n > 3)active substances exist during the cracking of n-dodecane.Therefore,the degree of cracking of n-dodecane may affect the type of available components and distribution of active particles for the entire reaction zone.

    Figure 4 shows the carbon materials obtained at two different injection rates: 30 μl min?1(a) and 50 μl min?1(b).When the injection rate of n-dodecane is increased, the surface of the Ni foam is unevenly distributed with granular agglomerate structure rather than graphene nanowalls. It can be confirmed that the increase of the injection rate means the increase of the proportion of carbon source components. The total number of gas molecules in the area increases when n-dodecane is uniformly propelled into the plasma reaction zone by a syringe pump, because the n-dodecane will be directly vaporized under the conditions of high-energy particle collision and low pressure. Similar to the increase of Ar flow, the n-dodecane molecule cannot obtain sufficient energy density for effective cracking at this time,in which the proportion of small molecular active groups will decrease,while the macromolecular active groups will increase and adhere to the pores of the Ni foam. Therefore, the active group materials and mechanism for carbon material growth have changed and led to the graphene nanowall structure not being produced on the surface of the Ni foam.

    Figure 3.SEM images of carbon material prepared in 10 min at different H2/Ar ratios: (a) 5:5; (b) 5:10; (c) 5:20; (d) 10:10 (500 W,30 μl min?1, 800°C).

    Figure 4.SEM images of carbon material prepared at different n-dodecane injection rates for 10 min: (a) 30 μl min?1 and (b) 50 μl min?1(500 W, H2/Ar = 5:10, 800°C).

    3.1.4.Effect of reaction temperature. The reaction temperature is an important influencing factor in this experimental system,especially the synergistic effect of high temperature,which can effectively reduce the power required by the plasma and reduce the adhesion of macromolecular particles.In previous research,carbon materials such as activated carbon, carbon nanotubes[26-28] and fullerenes [29] were generally prepared by CVD.In the conventional method of CVD, the reaction temperature needs to reach above 1000°C [30] and the operation time needs more than half an hour. Furthermore, we also need to provide more than 1000 W to the plasma source during the process of preparing graphene by plasma cracking. A high electron temperature also causes high macro temperature. The reaction temperatures mentioned above all pose challenges and requirements for the reaction equipment and energy input. Hence, searching for an effective way to lower the reaction temperature or seeking the most appropriate reaction temperature is also one target of this experiment.

    Currently, the method based on PECVD can provide an atmosphere with lower macroscopic temperature,which is one of the mainstream methods for preparing carbon materials[31-35].However,the reaction temperature in this experiment has an effect on both the gasification process of n-dodecane and the stabilization of excited-state particles. Therefore, the reaction temperature directly affects the structure and morphology of the carbon materials.

    Figure 5 shows the structure of the carbon material at reaction temperatures of 600°C, 700°C, 800°C and 900°C.When the heating temperature of the reaction is 600°C,it can be observed that the surface of the Ni foam is covered by a dense macromolecule, and it can be inferred from the SEM results that the conductivity is poor. Therefore, the hydrocarbon layer may be because the n-dodecane molecule does not obtain enough energy during the gasification process,and a large amount of the liquid hydrocarbon molecules are deposited on the surface of the Ni foam. When the reaction temperature is increased to 700°C, a large number of nucleation sites are formed on the surface of the Ni foam.This outcome indicates that active groups such as C2have been produced at this time. Meanwhile, the energy obtained by the n-dodecane molecule ensures that it will not adhere to the Ni substrate. When the reaction temperature reaches 800°C,the abundant active groups such as C2and CnHxgrow in the vertical direction at the nucleation point, and a graphene nanowall structure with a lateral dimension of 500-800 nm is prepared. This nanowall structure has a dense maze-like distribution on the plane and interlocks to form a void space. When the reaction temperature increases to 900°C, the formation of clustered graphene nanostructures can be observed. Compared with graphene nanowalls, the lateral dimension is only approximately 200 nm, which is only 1/4-1/3 of the layer structure. Furthermore, the cluster structure is denser and the pore structure is greatly reduced.At the same time, a similar layer structure with a scale of several tens of nanometers can be found from the partial enlargement of the surface of the flower cluster structure,possibly because under the condition of high temperature,the active groups of graphene are agglomerated when growing along a vertical orientation.A cluster of flower-like structures is formed under the action of surface stress,and the size of the surface layer structure is also limited due to the compression of the space.

    Compared with the ICP cracking process of methane in the previous work [36], where only a temperature range of 700°C-800°C modified and densified the graphene nanowalls, the structure of the carbon material prepared by n-dodecane is more sensitive to the changes of the reaction temperature.

    Figure 5.SEM images of carbon material prepared at different reaction temperatures for 10 min: (a)600°C, (b) 700°C,(c)800°C and (d)900°C (500 W, 30 μl min?1, H2/Ar = 5:10).

    Figure 6.Raman spectrum of graphene prepared by cleaving of n-dodecane (a) and methane (b) ((a) Operating conditions: 500 W, H2/Ar = 5:10, 30 μl min?1, 800°C. (b) Operating conditions: 500 W, H2/Ar = 5:10, 10 sccm, 800°C).

    3.2. Graphene structure analysis

    Considering the excellent electrical properties of graphene,we now analyze the conductivity of the prepared graphene.The electron transport ability of the graphene nanowalls is related to the degree of graphitization of the structure,because the closer the structure is to the theoretical hexagonal crystal structure of graphene, the more favorable the sp2hybrid orbital is to the movement of electrons.

    Figure 6 shows the corresponding graphene structure prepared under the explored optimum conditions of n-dodecane.The crystal structure of graphene is reached by analyzing the D peak (~1354 cm?1), G peak (~1586 cm?1), 2D peak(~2702 cm?1) and D + G peak (~2938 cm?1) in the Raman spectrum.

    Among them, the D peak reflects the defect structure of the hexagonal crystal contained in the graphene, and the G peak corresponds to the sp2hybrid structure in the graphene,and ID, IG, I2Dare the intensities of the D peak, G peak and 2D peak, respectively. The intensity of the G peak in figure 6(a)is slightly higher than that in figure 6(b),indicating that the prepared graphene using n-dodecane as a carbon source contains a relatively high proportion of the sp2structure. At the same time, the relative intensity ID/IGof the D peak and G peak in figure 6(a) is approximately 1.55, indicating that there is abundant edge structure or defect structure in the graphene nanowall layers. This outcome is consistent with the dense edge structure observed in the SEM image.

    In addition, the 2D peak corresponds to the degree of graphitization of the carbon material, and the D + G peak is the sum of the scattering peaks. In figure 6(a), the highintensity 2D peak means that the graphene nanowall layers have a higher degree of graphitization, and the relative intensity of the 2D peak and G peak at this time I2D/IGis approximately 0.48, which indicates that the graphene nanowall layers are formed by a large number of stacked single layers.

    In general, under the same optimized conditions, the graphene nanowalls prepared with n-dodecane and methane have quite similar crystal forms and defect structures. By controlling the appropriate operating parameters, the degree of graphitization of graphene can be effectively improved and the crystal structure can be optimized.

    3.3. Analysis of the effect of RF ICP for cracking n-dodecane

    Now,a summary of optimized conditions includes an applied input power of 500 W, a hydrogen/argon ratio of 5:10, an injection rate of 30 μl min?1and a reaction temperature of 800°C. And we can analyze and infer the effect and mechanism of the ICP cracking of n-dodecane by analyzing the graphene loading and detection of outlet gas composition.

    3.3.1. Graphene loading analysis. To compare the effect of cracking by using ICP with methane and n-dodecane carbon sources,the loading and cracking rate for a similar preparation of graphene with methane at 500 W,H2/Ar = 5:10,20 sccm,800°C and 5 min, is calculated as follows:

    where 22.4 l · mol?1is the molar volume of the gas under standard conditions, and 12 g · mol?1is the molar mass of carbon atoms,m1(M1)and m2(M2)are the masses of methane(n-dodecane)before and after reaction,v1is the methane flow rate and v2is the n-dodecane injection rate,while t1and t2are the reaction time.It is worth noting that the graphene obtained at this time has a rich edge structure and a high degree of graphitization. Therefore, it is meaningful to compare the graphene loading from different carbon sources.

    As shown in table 1,although we can obtain more carbon material on Ni foam from n-dodecane cracking, it provides a lower graphene ratio compared to methane. In general, the n-dodecane cracking rate is 6%-7%, and the methane cracking rate could reach 13.25%. This outcome indicates that in the plasma region, the proportion of n-dodecane efficiently cleaved into small molecular groups is lower, and more is discharged as gaseous macromolecules. Therefore,to further improve the degradation rate of n-dodecane, the energy density of the plasma reaction region also needs to be correspondingly improved. In addition, if the presence of carbon particles in the graphene structure is considered during the process of n-dodecane cracking,the true cracking rate will be lower than the above-calculated value.

    Figure 7.Diagram of the outlet gas composition under different hydrogen flows.

    Table 1.Graphene mass loading.

    The comparison of the graphene between methane and n-dodecane is consistent with the effects and conclusions caused by the different reaction conditions described above.N-dodecane requires more energy and more collisions of high-energy particles when the C-C bond and C-H bond are broken due to its large molecular weight. At the same time,the proportion of carbon atoms in n-dodecane is larger, and the specific gravity of hydrogen atoms is smaller. Therefore,compared with methane, the reaction produces relatively few active groups such as CnHx, especially decreasing raw materials such as C2and CH that are used for graphene growth. The reduced raw material causes insufficient hydrocarbon feedstock to bond to the nucleation sites on the Ni foam,explaining the lower yield of graphene obtained from n-dodecane in the table.

    3.3.2. Gaseous product analysis. We can also study the action mechanism of the reactive groups in the ICP cracking process by analyzing the components of the outlet gas. This analysis occurs because the reactive groups not only deposit and grow as solid products, but directly collide with each other and produce small molecular gases.

    By analyzing the outlet gas(i.e.the cracked gas product),it can be found that the gas phase products below C2mainly include CH4,C2H2,C2H4,C2H6and H2.Because hydrogen as a reaction gas directly affects the reaction and changes the final outlet gas composition,the change of the composition of the outlet gas under different hydrogen flow rates is the main focus.

    As shown in figure 7, it is worth noting that during the cracking process of n-dodecane,the content of hydrogen in the outlet gas is positively correlated with the flow rate of the inlet hydrogen, while in the methane cracking process, the outlet hydrogen declines and eventually stabilizes. Meanwhile, the proportion of hydrogen in the outlet gas is above 50% in the methane cracking process,while the proportion of hydrogen in the n-dodecane cracking process ranges from 1.3%-15.1%,which is much lower than the former. This outcome may be caused by the different cracking mechanisms of n-dodecane and methane. The carbon hydrogen ratio of methane (CH4) is 1:4, while n-dodecane (C12H26) is 6:13. Therefore, under the action of high-energy electrons in the plasma,methane will be cleaved to obtain relatively equal C2radicals and H radicals.In contrast, n-dodecane will produce fewer H radicals and more CnHxgroups, reducing the probability of hydrogen molecules being generated by collisions between H radicals. Combined with the etching effect of hydrogen on the surface structure of the material, hydrogen has a more prominent role in the process of preparing carbon materials or graphene from liquid hydrocarbons. Reasonable hydrogen content may effectively improve the quality of carbon materials.

    At the same time that the gaseous products below C2(CH4,C2H2,C2H4and C2H6)can be detected,the proportion of C2H2is low, less than 9%. The ratio of CH4, C2H4and C2H6is higher than that of C2H2. The ratio of CH4and C2H6is basically not affected by hydrogen flow, while the proportion of C2H4decreases with the increase in hydrogen flow.This outcome indicates that there is a parallel competition in the reaction of small molecules, and the hydrogen of the raw material will have a certain influence on this balance. Among them, C2H2and C2H4can form abundant nucleation points on the surface of the Ni foam,and they are the most important raw materials for carbon material growth. C2H4and C2H6can also continue to collide with high-energy electrons,excited Ar and H radicals to form basic constituent units of graphene, such as C2radicals and CnHx.

    3.3.3. Discussion on the uncertainty analysis. The uncertainty error may exist in some aspect of the experiment, for example, the pressure change of the gas path may cause unsteady airflow or the change of the voltage could lead to instability of the plasma region.Besides,due to the equipment limitation of the input power, the n-dodecane may not be effectively cracked to form graphene. In other words, the cracking rate with higher input power may have different outcomes, and this is the basis for further exploration.

    4. Conclusion

    In the present research, carbon doping is prepared by plasma cracking using n-dodecane as a carbon source. By exploring various conditions,it can be found that the applied input power of the plasma will cause differences in the degree of n-dodecane cracking, and different reactive groups will grow different carbon materials.Hydrogen could etch the surface of the carbon material in the plasma region, and argon gas can form argon radicals to transfer energy, but too much will reduce plasma energy efficiency. Cluster-like carbon particles may be formed under an excessive injection rate.The reaction temperature can reduce the required plasma input power.However, the structure of the carbon material in this paper is also directly affected by temperature. The morphology of VG changes from a point-like linear distribution to a lamellar structure and then to a spherical particle cluster with increasing temperature. As investigated above, the favorable reaction temperature for growth of the graphene structure is 800°C.

    In addition, from the results of Raman spectroscopy, we found that graphene nanowalls prepared from n-dodecane and methane have very similar crystal and defect structures. The relative intensity of the graphene D peak and G peak ID/IGprepared by n-dodecane is approximately 1.55, and the relative intensity of the 2D peak and G peak I2D/IGis approximately 0.48, indicating that the graphene has a rich defect structure and high degree of graphitization, respectively.

    Regarding the cracking effect of RF ICP on n-dodecane and methane under similar operating conditions,the cracking rate of n-dodecane is only 6%-7%, which is approximately half of that obtained from methane. The detection results of the outlet gas indicate that the gaseous products below C2mainly include CH4, C2H2, C2H4, C2H6and H2. Among them, the proportion of hydrogen in the outlet gas of n-dodecane cracking ranges from 1.3%-15.1%, which is much smaller than that obtained from methane cracking(approximately 50%). The proportion of C2H2is relatively low, not higher than 9%, while the ratio of CH4, C2H4and C2H6is higher than that of C2H2. In addition, the proportion of CH4and C2H6is basically not affected by hydrogen flow,while the proportion of C2H4decreases with the increase of hydrogen flow.

    猜你喜歡
    李曉東建華
    倒立奇奇
    東方磁卡李曉東:進擊的智能卡研發(fā)巨子
    時代人物(2019年27期)2019-10-23 06:11:58
    故事作文·低年級(2018年11期)2018-11-19 17:25:58
    米沙在書里
    可怕的事
    李曉東:我最喜歡的還是做歌手
    北廣人物(2018年20期)2018-06-27 05:29:42
    變變變
    阿嗚想做貓
    她在“處女”的高臺上:那自以為是的處女情結
    幽靈巴士
    18禁美女被吸乳视频| 18禁黄网站禁片免费观看直播| 午夜两性在线视频| 一区福利在线观看| 69av精品久久久久久| 非洲黑人性xxxx精品又粗又长| 亚洲avbb在线观看| 岛国在线观看网站| 无遮挡黄片免费观看| 亚洲精品美女久久久久99蜜臀| 老鸭窝网址在线观看| 亚洲成a人片在线一区二区| 黑人欧美特级aaaaaa片| 国产精品亚洲一级av第二区| 久久这里只有精品中国| 69av精品久久久久久| 亚洲精品456在线播放app | 亚洲片人在线观看| 两个人视频免费观看高清| 桃色一区二区三区在线观看| 国产伦一二天堂av在线观看| 在线视频色国产色| 国内毛片毛片毛片毛片毛片| xxxwww97欧美| 搞女人的毛片| 亚洲片人在线观看| 中国美女看黄片| 毛片女人毛片| 亚洲av成人精品一区久久| 国产精品1区2区在线观看.| av国产免费在线观看| 我要搜黄色片| 欧美日韩亚洲国产一区二区在线观看| 757午夜福利合集在线观看| 99国产极品粉嫩在线观看| 国产av不卡久久| 国产亚洲精品久久久com| www.熟女人妻精品国产| 国产亚洲av高清不卡| 国产高清激情床上av| 狠狠狠狠99中文字幕| 国产成人欧美在线观看| 久久久久免费精品人妻一区二区| 午夜免费成人在线视频| 亚洲精品中文字幕一二三四区| 久久这里只有精品19| 久久久精品大字幕| 999精品在线视频| 亚洲国产欧洲综合997久久,| 在线免费观看不下载黄p国产 | 一本精品99久久精品77| 国产精品日韩av在线免费观看| 午夜免费成人在线视频| 18禁黄网站禁片免费观看直播| av欧美777| 变态另类丝袜制服| 性色av乱码一区二区三区2| 国产成人影院久久av| 99久久精品国产亚洲精品| 精品99又大又爽又粗少妇毛片 | 久久天堂一区二区三区四区| 这个男人来自地球电影免费观看| 国产探花在线观看一区二区| 老熟妇仑乱视频hdxx| АⅤ资源中文在线天堂| 亚洲人与动物交配视频| 老司机深夜福利视频在线观看| 色在线成人网| 免费观看人在逋| 国产69精品久久久久777片 | 99精品久久久久人妻精品| 精品国内亚洲2022精品成人| 亚洲精品在线观看二区| 最近视频中文字幕2019在线8| 无人区码免费观看不卡| 久久久久久久久中文| 欧美+亚洲+日韩+国产| 色综合站精品国产| 亚洲欧美激情综合另类| 国产成+人综合+亚洲专区| 亚洲欧美日韩无卡精品| 亚洲精华国产精华精| 成人18禁在线播放| 欧美一区二区精品小视频在线| 亚洲av成人av| 久久这里只有精品19| 久久久久免费精品人妻一区二区| 精品国产三级普通话版| 青草久久国产| 成人亚洲精品av一区二区| 成人国产综合亚洲| 国产欧美日韩一区二区三| 又大又爽又粗| 真人做人爱边吃奶动态| 亚洲国产精品999在线| 搡老妇女老女人老熟妇| 亚洲精品在线美女| 久久久久久国产a免费观看| 熟女人妻精品中文字幕| 91在线观看av| av欧美777| 一边摸一边抽搐一进一小说| 99热精品在线国产| 女人高潮潮喷娇喘18禁视频| 黄频高清免费视频| 天堂影院成人在线观看| 亚洲一区二区三区色噜噜| 国产一区二区激情短视频| 精品一区二区三区四区五区乱码| 国产熟女xx| 日韩成人在线观看一区二区三区| 亚洲av熟女| aaaaa片日本免费| 国产97色在线日韩免费| 色精品久久人妻99蜜桃| 午夜福利视频1000在线观看| 成年免费大片在线观看| www国产在线视频色| 级片在线观看| 中文字幕高清在线视频| 小说图片视频综合网站| 无遮挡黄片免费观看| 国产一区二区在线av高清观看| 中亚洲国语对白在线视频| 最新在线观看一区二区三区| 精品国内亚洲2022精品成人| 欧美日韩综合久久久久久 | 国产精品 国内视频| 欧美3d第一页| 婷婷亚洲欧美| 欧美黑人欧美精品刺激| 99久久国产精品久久久| 超碰成人久久| 精品乱码久久久久久99久播| 最近在线观看免费完整版| 一区二区三区国产精品乱码| 国产99白浆流出| 五月玫瑰六月丁香| 国产一区二区激情短视频| 国产三级中文精品| 国产三级中文精品| 美女午夜性视频免费| 久久精品夜夜夜夜夜久久蜜豆| 五月伊人婷婷丁香| 国产精品爽爽va在线观看网站| 日本一二三区视频观看| 亚洲男人的天堂狠狠| 成人一区二区视频在线观看| 亚洲一区二区三区不卡视频| 精品国产超薄肉色丝袜足j| 精品国产美女av久久久久小说| 国产高清有码在线观看视频| 一级作爱视频免费观看| 中出人妻视频一区二区| 中文字幕高清在线视频| 国产极品精品免费视频能看的| 美女大奶头视频| 天堂√8在线中文| 男人的好看免费观看在线视频| www.精华液| 国产精品亚洲美女久久久| 亚洲精品一区av在线观看| 99在线人妻在线中文字幕| 十八禁人妻一区二区| 亚洲av电影不卡..在线观看| 一个人看视频在线观看www免费 | 日本熟妇午夜| 国产午夜福利久久久久久| 婷婷精品国产亚洲av在线| 中文字幕人妻丝袜一区二区| 欧美在线一区亚洲| 欧美日韩亚洲国产一区二区在线观看| 亚洲国产日韩欧美精品在线观看 | 久久久国产欧美日韩av| 亚洲七黄色美女视频| 性欧美人与动物交配| 一本综合久久免费| 巨乳人妻的诱惑在线观看| 舔av片在线| 无人区码免费观看不卡| 一级毛片女人18水好多| 黑人巨大精品欧美一区二区mp4| 99re在线观看精品视频| 色吧在线观看| 午夜免费激情av| 亚洲第一欧美日韩一区二区三区| 欧美日韩瑟瑟在线播放| 久久精品人妻少妇| 欧美日韩中文字幕国产精品一区二区三区| 女生性感内裤真人,穿戴方法视频| 亚洲精品久久国产高清桃花| 欧美日韩福利视频一区二区| 成人三级做爰电影| 久久午夜综合久久蜜桃| 国内精品一区二区在线观看| www日本黄色视频网| 在线观看美女被高潮喷水网站 | 不卡av一区二区三区| 亚洲精品一区av在线观看| 天堂√8在线中文| 日日干狠狠操夜夜爽| 18禁黄网站禁片午夜丰满| 真人做人爱边吃奶动态| 亚洲真实伦在线观看| 制服丝袜大香蕉在线| 久久九九热精品免费| 操出白浆在线播放| 精品无人区乱码1区二区| 美女 人体艺术 gogo| 亚洲第一电影网av| 欧美绝顶高潮抽搐喷水| 国产真人三级小视频在线观看| 久久中文字幕人妻熟女| 18美女黄网站色大片免费观看| 女人被狂操c到高潮| 亚洲午夜理论影院| 欧美+亚洲+日韩+国产| 少妇裸体淫交视频免费看高清| 熟女人妻精品中文字幕| 校园春色视频在线观看| 一本综合久久免费| 国产极品精品免费视频能看的| 国产欧美日韩一区二区三| www.www免费av| 久久国产精品人妻蜜桃| 国产午夜福利久久久久久| 久久99热这里只有精品18| 精品欧美国产一区二区三| 国产又黄又爽又无遮挡在线| 精品国产超薄肉色丝袜足j| 国产黄a三级三级三级人| www.www免费av| 熟女少妇亚洲综合色aaa.| 午夜精品一区二区三区免费看| 老司机在亚洲福利影院| av中文乱码字幕在线| 久久久久久大精品| 亚洲色图 男人天堂 中文字幕| svipshipincom国产片| 麻豆成人av在线观看| 免费看a级黄色片| 国产精品日韩av在线免费观看| 丝袜人妻中文字幕| 三级毛片av免费| 级片在线观看| 日韩中文字幕欧美一区二区| 伊人久久大香线蕉亚洲五| 天堂√8在线中文| 俺也久久电影网| 老司机福利观看| 好看av亚洲va欧美ⅴa在| 91字幕亚洲| 久久久精品欧美日韩精品| 操出白浆在线播放| 国产 一区 欧美 日韩| 色哟哟哟哟哟哟| 国产一区二区在线av高清观看| 三级毛片av免费| 少妇熟女aⅴ在线视频| 2021天堂中文幕一二区在线观| 精品免费久久久久久久清纯| 午夜成年电影在线免费观看| 在线观看免费视频日本深夜| 久久中文看片网| 可以在线观看的亚洲视频| 国产亚洲精品一区二区www| 日本黄大片高清| 九色成人免费人妻av| x7x7x7水蜜桃| 免费看光身美女| 亚洲av免费在线观看| 别揉我奶头~嗯~啊~动态视频| 国产在线精品亚洲第一网站| 久久香蕉精品热| 精品国产美女av久久久久小说| 欧美在线一区亚洲| 久久人妻av系列| 99视频精品全部免费 在线 | 亚洲五月天丁香| 精品久久久久久久久久久久久| 亚洲精品一卡2卡三卡4卡5卡| 久久中文看片网| bbb黄色大片| 国产精品99久久久久久久久| 色噜噜av男人的天堂激情| www.www免费av| 在线国产一区二区在线| 国产真人三级小视频在线观看| 午夜精品在线福利| 国产精品亚洲一级av第二区| 亚洲国产精品成人综合色| 国产成人精品久久二区二区免费| 变态另类丝袜制服| 脱女人内裤的视频| 老汉色av国产亚洲站长工具| 高潮久久久久久久久久久不卡| 婷婷六月久久综合丁香| 成熟少妇高潮喷水视频| 99re在线观看精品视频| 亚洲欧美精品综合久久99| 久久久久亚洲av毛片大全| 成年人黄色毛片网站| 久久国产精品影院| 国模一区二区三区四区视频 | 午夜免费激情av| 免费无遮挡裸体视频| 免费看美女性在线毛片视频| 亚洲国产欧美网| 亚洲,欧美精品.| 国产成人啪精品午夜网站| 午夜福利18| 国产麻豆成人av免费视频| 色哟哟哟哟哟哟| 国产成人影院久久av| 亚洲色图av天堂| 制服丝袜大香蕉在线| 99久久99久久久精品蜜桃| 亚洲精品美女久久久久99蜜臀| 天堂影院成人在线观看| 色吧在线观看| 国产精品一区二区免费欧美| 免费电影在线观看免费观看| 制服人妻中文乱码| 亚洲激情在线av| 久久伊人香网站| 最新中文字幕久久久久 | 又粗又爽又猛毛片免费看| 国产亚洲av嫩草精品影院| 又紧又爽又黄一区二区| 十八禁人妻一区二区| 黄色日韩在线| 麻豆av在线久日| 欧美日韩瑟瑟在线播放| 91久久精品国产一区二区成人 | 久久精品91蜜桃| 丝袜人妻中文字幕| 日本成人三级电影网站| 在线观看午夜福利视频| 女同久久另类99精品国产91| 国产精品久久视频播放| 熟女电影av网| 男插女下体视频免费在线播放| 又紧又爽又黄一区二区| 男插女下体视频免费在线播放| 一级黄色大片毛片| 美女cb高潮喷水在线观看 | 午夜激情福利司机影院| 国产午夜福利久久久久久| 一本久久中文字幕| 999久久久精品免费观看国产| 黄片大片在线免费观看| 精品国产亚洲在线| 99在线视频只有这里精品首页| 国产一区二区三区视频了| 久久性视频一级片| 1000部很黄的大片| 国产成人av教育| 亚洲 国产 在线| 一本久久中文字幕| 精品一区二区三区视频在线观看免费| 亚洲精品久久国产高清桃花| 久久国产精品影院| 给我免费播放毛片高清在线观看| 悠悠久久av| 国产私拍福利视频在线观看| 久久午夜综合久久蜜桃| 波多野结衣高清作品| 欧美一级a爱片免费观看看| 五月玫瑰六月丁香| 国产av麻豆久久久久久久| 19禁男女啪啪无遮挡网站| 成人一区二区视频在线观看| 90打野战视频偷拍视频| 9191精品国产免费久久| 亚洲九九香蕉| netflix在线观看网站| 综合色av麻豆| 一本综合久久免费| 欧美zozozo另类| 欧美不卡视频在线免费观看| 这个男人来自地球电影免费观看| 国产午夜福利久久久久久| 成年人黄色毛片网站| 三级国产精品欧美在线观看 | 久久欧美精品欧美久久欧美| 一本久久中文字幕| 欧美一级a爱片免费观看看| 成人精品一区二区免费| 天堂动漫精品| 级片在线观看| 亚洲片人在线观看| 国产亚洲av嫩草精品影院| 免费av不卡在线播放| 国产伦人伦偷精品视频| 美女被艹到高潮喷水动态| 丰满人妻一区二区三区视频av | 久久中文字幕一级| 夜夜躁狠狠躁天天躁| 亚洲片人在线观看| 特大巨黑吊av在线直播| 日韩欧美国产一区二区入口| 欧美日韩一级在线毛片| 国产极品精品免费视频能看的| 91在线精品国自产拍蜜月 | 黑人操中国人逼视频| 精品国产美女av久久久久小说| 在线看三级毛片| 色哟哟哟哟哟哟| a在线观看视频网站| 免费看光身美女| 少妇的逼水好多| 日韩 欧美 亚洲 中文字幕| 免费在线观看成人毛片| 99久久久亚洲精品蜜臀av| 国产高清有码在线观看视频| 日韩欧美在线乱码| 国产成年人精品一区二区| 亚洲国产精品久久男人天堂| 成人av一区二区三区在线看| 少妇裸体淫交视频免费看高清| 国产高清videossex| 97人妻精品一区二区三区麻豆| 给我免费播放毛片高清在线观看| 麻豆成人av在线观看| 日韩av在线大香蕉| 波多野结衣巨乳人妻| 国产成年人精品一区二区| 国产视频内射| 三级国产精品欧美在线观看 | 看片在线看免费视频| www.999成人在线观看| 制服人妻中文乱码| 久久精品国产亚洲av香蕉五月| 老司机午夜福利在线观看视频| 成年女人看的毛片在线观看| 国产精品九九99| 怎么达到女性高潮| 88av欧美| 天堂影院成人在线观看| 热99在线观看视频| 成熟少妇高潮喷水视频| 国产一区二区在线观看日韩 | 亚洲成av人片免费观看| 国语自产精品视频在线第100页| 一夜夜www| 亚洲自偷自拍图片 自拍| 黄频高清免费视频| 少妇熟女aⅴ在线视频| 国产成人精品久久二区二区91| 天堂av国产一区二区熟女人妻| 九色成人免费人妻av| 国产激情欧美一区二区| 国产av不卡久久| 精品国内亚洲2022精品成人| АⅤ资源中文在线天堂| 99re在线观看精品视频| 久久这里只有精品19| 人妻夜夜爽99麻豆av| 欧美在线一区亚洲| 国产免费男女视频| 视频区欧美日本亚洲| xxx96com| 久久精品国产亚洲av香蕉五月| 国产单亲对白刺激| 国产野战对白在线观看| 国产成人一区二区三区免费视频网站| 黄色 视频免费看| 久久午夜亚洲精品久久| 亚洲va日本ⅴa欧美va伊人久久| 久久久国产精品麻豆| 成人一区二区视频在线观看| 欧美黑人欧美精品刺激| 国产 一区 欧美 日韩| 丰满的人妻完整版| 免费看日本二区| 日韩成人在线观看一区二区三区| aaaaa片日本免费| 日韩人妻高清精品专区| 欧美乱妇无乱码| 亚洲av五月六月丁香网| 国内毛片毛片毛片毛片毛片| 国产免费男女视频| 桃红色精品国产亚洲av| 午夜免费成人在线视频| 国产av一区在线观看免费| 国产黄a三级三级三级人| 又黄又粗又硬又大视频| 男插女下体视频免费在线播放| 国产三级中文精品| 熟女少妇亚洲综合色aaa.| 色综合亚洲欧美另类图片| 一级毛片精品| 日日干狠狠操夜夜爽| 成人特级黄色片久久久久久久| 熟女人妻精品中文字幕| 在线观看一区二区三区| 一级毛片女人18水好多| 亚洲欧美一区二区三区黑人| 亚洲中文字幕日韩| 国内精品久久久久久久电影| 九九久久精品国产亚洲av麻豆 | www.自偷自拍.com| 午夜成年电影在线免费观看| 女生性感内裤真人,穿戴方法视频| 久久精品国产综合久久久| 中亚洲国语对白在线视频| 日韩免费av在线播放| 在线看三级毛片| 久久久成人免费电影| 久久久精品大字幕| 免费大片18禁| 国产精品亚洲一级av第二区| 在线看三级毛片| 色综合亚洲欧美另类图片| 少妇的逼水好多| 母亲3免费完整高清在线观看| 精品一区二区三区视频在线观看免费| 美女高潮的动态| 免费电影在线观看免费观看| 搡老熟女国产l中国老女人| 日本 欧美在线| 亚洲 国产 在线| 国产成人啪精品午夜网站| 国产亚洲精品一区二区www| 中亚洲国语对白在线视频| 成人国产一区最新在线观看| 欧美日韩亚洲国产一区二区在线观看| 波多野结衣高清作品| 欧美绝顶高潮抽搐喷水| 精品欧美国产一区二区三| 国产精品久久久av美女十八| 国产高清三级在线| 国产精品av久久久久免费| 又紧又爽又黄一区二区| 国产成人一区二区三区免费视频网站| 国产蜜桃级精品一区二区三区| 成人精品一区二区免费| 免费看十八禁软件| 国产精品影院久久| 制服人妻中文乱码| 在线观看美女被高潮喷水网站 | 精品国产乱子伦一区二区三区| 在线观看美女被高潮喷水网站 | 99精品在免费线老司机午夜| 欧美成人性av电影在线观看| 久久久久久人人人人人| 欧美日韩亚洲国产一区二区在线观看| 国产午夜精品久久久久久| 欧美日韩瑟瑟在线播放| 操出白浆在线播放| 黄色女人牲交| 人人妻人人看人人澡| 最近最新免费中文字幕在线| 日本五十路高清| 欧美大码av| 91av网站免费观看| 黄色 视频免费看| 精品久久久久久成人av| 淫秽高清视频在线观看| 九九在线视频观看精品| 97超级碰碰碰精品色视频在线观看| 免费电影在线观看免费观看| 欧美绝顶高潮抽搐喷水| 一级作爱视频免费观看| 久久精品aⅴ一区二区三区四区| 亚洲av中文字字幕乱码综合| 天天躁日日操中文字幕| 亚洲精品一区av在线观看| 91老司机精品| 亚洲av第一区精品v没综合| 国产高清视频在线播放一区| 熟女少妇亚洲综合色aaa.| 欧美性猛交黑人性爽| 国产精品1区2区在线观看.| 亚洲人成伊人成综合网2020| 亚洲av美国av| 757午夜福利合集在线观看| 国产成人aa在线观看| 黄色女人牲交| 国产精品亚洲美女久久久| 最近在线观看免费完整版| 国产主播在线观看一区二区| 久久精品国产综合久久久| 给我免费播放毛片高清在线观看| 国产一区二区在线观看日韩 | 亚洲色图av天堂| 免费在线观看亚洲国产| 美女黄网站色视频| 亚洲va日本ⅴa欧美va伊人久久| 在线观看免费午夜福利视频| 国产精品av视频在线免费观看| 在线观看舔阴道视频| 亚洲欧美日韩高清专用| 久久婷婷人人爽人人干人人爱| 9191精品国产免费久久| 男人和女人高潮做爰伦理| 亚洲片人在线观看| 少妇的逼水好多| 久久九九热精品免费| 最新中文字幕久久久久 | 国产成人福利小说| 激情在线观看视频在线高清| 久久这里只有精品19| 日本精品一区二区三区蜜桃| 国产精品一区二区三区四区免费观看 | 99国产精品一区二区蜜桃av| 男人舔奶头视频| 美女扒开内裤让男人捅视频| 18禁黄网站禁片免费观看直播| 精品日产1卡2卡| 99精品欧美一区二区三区四区| 午夜成年电影在线免费观看| 日本 av在线| 热99re8久久精品国产| 无遮挡黄片免费观看|