• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    A radar-infrared compatible broadband absorbing surface:Design and analysis*

    2021-07-30 07:43:02QingTaoYu余慶陶YuanSongZeng曾元松andGuoJiaMa馬國佳
    Chinese Physics B 2021年7期
    關鍵詞:余慶

    Qing-Tao Yu(余慶陶), Yuan-Song Zeng(曾元松), and Guo-Jia Ma(馬國佳)

    Aviation Key Laboratory of Science and Technology on Advanced Surface Engineering,

    AVIC Manufacturing Technology Institute,Beijing 100024,China

    Keywords: stealth,infrared-radar compatible,broadband absorbing,patterned surface

    1. Introduction

    In modern warfare, aircrafts are subjected to various detection methods. Among them, detection of radar reflection and infrared emission are the two major means to locate and trace an aircraft. The microwave reflected by an aircraft can be collected by radar systems to guide the missile approaching the aircraft. When approaching,an infrared sensor on the missile begins to seek and lock on the infrared signal emitted from the aircraft. To increase aircraft survivability during combats,technologies have been developed to reduce radar reflection in a wide frequency range and to supress infrared emission at the same time.

    Radar absorbing materials (RAMs) were developed to mitigate the microwave reflection. RAMs containing ferrites or carbonyl iron flakes (CIFs) are considered to be some of the most effective magnetic absorbents,and have been widely used in stealth coating on aircrafts nowadays. However,a typical CIF composite RAM has a high infrared emissivity[1]between 0.8-1, therefore it becomes an intense infrared source that could radiate large amount of infrared energy at elevated temperature.

    Low radar reflection and low infrared emissivity are somewhat contradictory in nature,as low-emissivity materials such as copper, gold, platinum (emissivity below 0.1[2]) and ITO are good conductors and thus are highly reflective to microwave. One of the solutions to infrared-radar compatibility is to apply coating that contains micro aluminum flakes. The sizes of these micro flakes are in order of magnitude smaller than the microwave wavelength, allowing diffraction of the microwave and providing relatively low emissivity at the same time. To ensure low emissivity, aluminum flakes have to be uniformly distributed in the resin, and ideally they should be isolated from each other as aggregation of particles may have a negative influence on radar absorption.

    1.1. Patterned surface for stealth application

    CIF composite RAMs are high in density, therefore the thickness of such coating on aircrafts is limited to several millimeters and sometimes less than a millimeter. As coating thickness is strictly restricted and the CIF’s permeability is bounded by Snoek’s limit,[3]efforts have been made to creating patterns and structures in RAM coating for broadband radar absorbers.[4-6]Among those attempts, Liet al.[5]increased the-10 dB absorption bandwidth in the range of 2-40 GHz by more than 6 times through engraving periodic square patterns with certain depth on a layer of CIF composite. They conclude that in the low frequency range, the improved performance is dominated by theλ/4 effect inside the engraved gap, while in the high frequency range, diffraction of the electromagnetic waves at structure corners plays a more important role. Similar effects have also been discussed in the biomimic research of Huanget al.,[6]who produced a layer of RAM with hexagonal structures, mimicking the microstructures on the moth eye surface which largely reduces the reflection of visible light to avoid predators. Their results showed that when hexagonal periodic pattern has a side length of 3.2 mm, the-8 dB absorption bandwidth increases from 3 GHz to 11 GHz in the 2-18 GHz range.

    On the other hand, frequency selective surfaces (FSSs)are metal surfaces with periodic patterns designed to reflect,transmit or absorb microwave of certain frequencies. Some studies explored the possibility of combining FSS with other materials for broadband radar absorbing purpose. Several articles[7-10]incorporated FSSs between layers of RAMs,forming a sandwich structure which leads to broader absorption bandwidth. Tianet al.[11]combined a top layer FSS with a bottom-layer high resistive surface for infrared-radar compatible stealth purpose. As the FFS periodic pattern of copper film covers more than 80% of the surface area, the resulting surface has an average infrared emissivity below 0.3. However,its radar absorption bandwidth is relatively narrow,where the-10 dB bandwidth merely covers x-band(8-12 GHz). In some of the latest studies,[12-14]two layers of FSSs were combined together to form a broadband absorber. Xuet al.[12]showed that at a thickness of 7 mm and with proper FSS pattern design the-10 dB absorption bandwidth can reach 18 GHz and the infrared emissivity can be maintained below 0.3. Additionally, patterned ITO was used in their study to achieve optical transparency.

    In this study, a radar-infrared compatible broadband absorbing surface(RICBAS)design is proposed. The proposed design follows the idea that FSSs play an important role in infrared-radar compatibility. With proper design,an FSS pattern can cover most of the surface area,providing low infrared emissivity and tuning the overall input impedance of the surface at the same time.It couples with patterned CIF composite RAM to promote radar absorbing performance.

    A transmission-line-based model (TLM) is developed to analyze the reflection loss of the designed surface and the results are compared with that produced by the finite element method(FEM).Parametric analyses are conducted to explore influences of basic design variables on radar absorbing performance. An optimization is conducted to find the design variables that lead to maximum-10 dB absorption bandwidth within the 2-18 GHz range. An experiment is provided in the end to qualitatively demonstrate that the conceptual design of RICBAS is capable of tuning the reflection loss curve.

    2. Design and modeling

    2.1. Design

    The designed RICBAS combines structured RAM and FSS,as shown in Fig.1.

    Fig.1. Schematic of RICBAS structure design: (a)surface structures,(b)a single unit cell.

    In the current design, the FSS and the RAM share the same square pattern.This assumption largely reduces the complexity in optimization and manufacturing,yet still allows the study of design principles.

    As shown in Fig.1(a),the structure consists of a top layer of thin metal film,a middle layer of CIF composite RAM,and a bottom layer of metal backing. The metal film only covers the top surface of the structures. It is also assumed that the metal film thickness is much larger than the microwave skin depth in the 2-18 GHz range(several hundreds of nanometers for common metals), and much smaller than the microwave wavelength; therefore the thickness effect of the metal film can be neglected. The middle layer has a total thickness oftand the depth of the structure isd. This RICBAS consists of repetitive square unit cells,Fig.1(b),with side length beingaand the side length of the RAM structure can be expressed asac,wherecis between zero and one.

    In the analysis,the coating thicknesstis set to be 1.5 mm,which is a typical RAM thickness on an aircraft. The structure depthdshould be strictly smaller thant, as any exposure of the metal backing would drastically increase microwave reflection. The type of the CIF composite used in the current analysis is similar to that in the study of Liet al.[3]Its relative dielectric parameters,shown in Fig.2,are kindly provided by State Key Lab of Advanced Technology for Materials Synthesis and Processing,Wuhan University of Technology.

    Fig.2. Relative permittivity and permeability of the CIF composite.

    2.2. Modeling

    A transmission-line-based model(TLM)is developed for such a patterned surface to analyze the microwave absorbing performance. The result is analyzed and compared with that generated by the finite element method. Parametric analyses are then conducted to study influences of the three primary variablesa,dandcon reflection loss.

    The transmission line method has been well studied and widely applied in studying the frequency selective surface[15]as well as RAMs.In the configuration where metal patches are placed on a layer of dielectric, the equivalent circuit is a parallel circuit between impedance of CIF composite RAM and FSS metal film,as shown in Fig.3.

    Fig.3. Equivalent circuit of the layered RICBAS surface.

    The reflection coefficientΓcan be expressed as

    where the air impedanceZair, relative to the free space impedance, is approximately one and the total input impedance of the parallel circuitZincan be written as

    In Eq.(2),ZFSSandZRAMare impedances of the FSS top layer and the RAM layer, respectively. In the current design,the RAM consists surface structure with a depth ofd. Therefore, the overall RAM layer may be alternatively considered as a two-layer structure: the lower one is a uniform layer with a thickness oft-d,consisting of only CIF composite;and the upper one is a structured layer of thicknessd, consisting of both CIF and air.

    The input impedance of thekth layer in a multi-layer structure[16]can be expressed as

    whereλis wavelength.

    As the two layers are placed on a metal backing,Z0is 0,and the total input impedance of RAM becomes

    whereδcould be either permittivityεor permeabilityμ,andfairis the volume fraction of air.

    For FSS surface with square patches, the impedanceZFSSunder normally incident wave can be estimated by the expression[18]

    Equations (2), (5) and (8) estimate the overall surface input impedance, which can be tuned by the three geometrical parametersa,candd. Then the overall reflection loss can be estimated using Eq.(1).

    3. Model analysis

    The reflection loss evaluated by the developed TLM is compared with that generated by a commercial FEM software.In the FEM analysis,a periodic boundary condition is used to study the surface response of microwave by analyzing one single unit cell.

    The reflection loss of the uniform slab without patterns is shown in Fig. 4. With the volume fractionfairbeing 0 in Eq. (6) andZin=ZRAM, the result from TLM shows good agreement with that from FEM.The two curves overlap each other, where the maximum discrepancy, as low as 1.6%, occurs at around 8.4 GHz. The resulting curves also agree well with the result by Liet al.[5]

    Fig.4.Reflection loss of 1.5 mm uniform slab evaluated by two models.

    For patterned surface in the following parametric analysis, a set of nominal values,a=1 mm,d=0.5 mm, andc=0.9,are chosen to set the benchmark. Calculated by both the models,the benchmark reflection loss of the patterned surface with and without the FSS layer(RAM structure only)are given in Fig. 5. In the absence of the FSS layer, as shown in Fig. 5(a), both the models predict an increase of the-10 dB absorption bandwidth, from 4.4 GHz to 6.0 GHz by FEM and to 4.9 GHz by TLM. Also, both the models capture the changing trend that absorption peak moves towards higher frequency.In FEM,the absorption peak appears at 8.0 GHz while the TLM predicts a peak at 7.0 GHz. The intensity of the peak evaluated by FEM is 15.9 dB,4%lower than that of the TLM.The two curves show large discrepancy in the 8-18 GHz range.As discussed by Liet al.,[5]the microwave diffraction at corners of the surface pattern is the dominating mechanism of the reflection loss in high frequency range,which cannot be effectively captured by the current TLM.

    Figure 5(b) shows the benchmark reflection loss of the patterned surface with the FSS layer. Compared with the previous results,both the models indicate that the appearance of 1 mm square metal patches on the top surface moves the absorption peak towards lower frequency and reduces the performance in high frequency. The-10 dB absorption bandwidth decreases from 6.0 GHz to 4.7 GHz in FEM,and from 4.9 GHz to 3.9 GHz in TLM.An increase in the intensity of the absorption peak is observed in the FEM result. With the FSS layer,the peak absorption loss increases from-16 dB to-18.3 dB,which could be caused by the overlapping of the absorption peaks of patterned RAM and FSS.

    Fig. 5. Benchmark reflection loss: (a) without the FSS layer (RAM structure only), (b) without the FSS layer (RAM structure+FSS pattern).

    The influence of unit cell sizeais studied first. The results produced by FEM is demonstrated in Fig. 6(a). Whenais 0.1 mm, in an order of magnitude smaller than its nominal value, the absorption peak changes from 6.4 GHz in the benchmark to 8.5 GHz. While the reflection loss between 2-8 GHz decreases,the performance in the range of 8-18 GHz is largely improved.The appearance of FSS in this case has little influence on the curve. In both the cases,the-10 dB absorption bandwidth is larger than that in the benchmark,increasing from 6.0 GHz to 6.7 GHz.

    As the side length increases from 0.1 mm to 5 mm,in the case without an FSS layer,the absorption peak moves towards low frequency,but is still higher than that of the uniform slab.A distinct difference is observed in the case with the FSS layer.The 5 mm square metal patch largely affects the reflection loss in the 4-18 GHz range.The absorption peak shifts to 3.2 GHz,and the-10 dB absorption bandwidth drastically decreases to only 0.7 GHz. When the size of the FSS pattern is in the order of wavelength of the microwave, microwaves of higher frequency can not pass the metal patch and thus becomes highly reflective.

    The results produced by TLM are given in Fig.6(b). The TLM developed in this study adopts the MG equation to represent the patterned CIF composite layer with a uniform CIF-air layer. The dielectric parameters of such a CIF-air layer only depends on the volume fraction of air,fair,which is independent of the unit cell size. Therefore, the current model does not include the size effect of the RAM structure. Yet, similar trends have been observed with the FSS layer, compared to the results produced by FEM. After comparing the curves produced by the two models, it seems that the FEM model is more sensitive to the variation of unit cell size.

    With FEM analysis,it can be shown that further decrease inawill not have much influence on the reflection loss curve.Curves ofabeing 0.05 and below are almost identical to that ofa=0.1. As the size of unit cell is in order of magnitude smaller than the wavelength, the wave does not “see” the individual structure. However,smaller unit cell could affect the infrared emissivity in a negative way. Firstly, ifais smaller than the wavelength of infrared(several micrometers),infrared emittance from the CIF composite may pass through the metal film at the top of the structure. Secondly,if the values ofcandtare kept to be unchanged,smallerawill result in larger overall surface area. Both will increase the total surface infrared energy emission.

    Fig. 6. Influence of the size of unit cell on reflection loss by (a) FEM and(b)TLM.

    Influence of the RAM structure depthdhas been discussed by Liet al.,[5]who attributed the improved performance in a high-frequency range to the 4/λresonance at the etched area. Similar trends have been captured by both the models, although the FEM model is more sensitive to the change in structure depth, as the absorption peak in Fig. 7(a)shifts to a higher frequency compared to that evaluated by the TLM model, as shown in Fig. 7(b). Another observation in Fig. 7(a) is that the appearance of 1 mm square FSS layer shifts the two curves differently. The FSS layer has smaller impact to the 0.2 mm depth structure. For example,in the case ofd=1.2 mm, the FSS layer increases the reflection coefficient at 18 GHz from 0.295 (-10.6 dB) to 0.562 (-5.0 dB),while in the case ofd=0.2 mm,such a value increases from 0.562(-5.0 dB)to 0.708(-3.0 dB).This observation implies that the influences on reflection loss by RAM structure and FSS pattern are intertwined,instead of being independent and linear.

    In Fig.7(b),it can be seen that,although TLM is capable of capturing trends of the reflection loss with varying structure depth,the resulting curves significantly deviate from the FEM analysis in high-frequency range,and especially under a largedvalue. This could be again caused by the inaccurate representation of structured RAM with uniform CIF-air mixture.Also, the absence of wave diffraction mechanism at structure corners contributes to the error in high frequency.

    Fig. 7. Influence of structure depth on reflection loss by (a) FEM and(b)TLM.

    The value ofcis the ratio of structure size to the size of unit cella. Withabeing fixed, variation ofcnot only affects the size of the structure (ac), but also affects the CIFair volume fraction (1-c2), thus changing the effective dielectric parameters of the structured layer. In both the FEM and TLM results shown in Figs. 8(a) and 8(b), as the value ofcincreases from 0.8 to 0.95,absorption peaks shift to high frequencies, the-10 dB absorption bandwidth increases and the absorption performance in high frequency is improved. A smallercmeans smaller percentage areal coverage of the metal film, which directly leads to higher surface infrared emissivity. Therefore, the changing trends in Fig. 8 indicate that a trade-off exists between lower infrared emissivity and better radar absorption performance in the presented RICBAS design,where an optimization can be used to find a balance point between the two sides.

    Fig.8. Influence of the value of c on reflection loss by(a)FEM and(b)TLM.

    4. Optimization

    The above parametric analyses have shown that the three variables affect the overall radar absorbing performance in a convoluted way. Both RAM structure and FSS pattern can be used to tune the reflection loss curve. An optimization is conducted in this section aiming at maximizing the-10 dB absorption bandwidth in the 2-18 GHz range.

    On the other hand, as RICBAS is also designed for infrared stealth, a low infrared emissivity, say 0.3, is set as a boundary condition in the optimization process. The average infrared emissivityεavgof the patterned surface may be estimated by the empirical formula[11]

    The value ofdis bounded by the thickness of the CIFcomposite RAM layer,so 0<d <1.5 mm. Based on the parametric analysis ofa,if the size of FSS pattern is large,it will hinder the radar absorption in high frequency range.Additionally,when the size ofais close to 0.1 mm,it will pose almost negligible effect on radar absorption. Therefore,ais set to be 0.1≤a ≤3 mm to narrow down the optimization search space.

    Fig. 9. Curve of reflection loss optimized for maximum -10 dB absorption bandwidth.

    The optimization process is performed by the embedded optimizer of the commercial FEM software. After several dozens of iterations, a set of optimized values are given asa=0.58 mm,d=1.08 mm andc=0.87. The resulting curve of reflection loss at the optimized points is plotted along with that of the uniform slab in Fig.9. The optimized design yield-10dB reflection loss between 7.9 GHz and 18 GHz. The corresponding absorption bandwidth is 10.1 GHz,115%more than that of the uniform slab the absorption peak occurs at 11.4 GHz with a maximum-22.5 dB reflection loss. The corresponding surface infrared emissivity,according to Eq.(12),would be around 0.287. In the current design,FSS shares the same pattern with the RAM structure. This design can be rather easily realized by first depositing a layer of metal on the CIF composite by physical vapor deposition (PVD), and then manufacturing the pattern and structure with machining or laser. Although the design reduces the difficulties in design and manufacture,it also limits further optimization. In future research, FSS and RAM may have independent patterns, and the optimized results may yield a better infrared-radar stealth performance.

    5. Experiment

    An experiment was conducted to demonstrate that the conceptual design is capable of improving the radar absorption performance while allowing most of the surface being covered by metal film.

    5.1. Experiment procedure

    To prepare the CIF composite layer, CIF was fully mixed with epoxy resin and uniformly sprayed onto two 180 mm×180 mm steel plates. They were then placed in an oven to cure for 12 hours at 50°C.The resulting CIF composite RAM is a 1.4-mm-thick black layer as shown in Fig.10(a).A vector network analyzer was used to measure the reflection loss curve of one plate. After that,both plates were placed in a vacuum chamber and a layer of copper was deposited on the RAM surface by magnetron sputtering, a type of PVD process. The fully coated surfaces have a purplish-orange color with metallic gloss, as shown in Fig. 10(b), and its reflection loss was measured once again.

    Fig.10. (a)CIF composite slab and(b)copper coated CIF composite slab.

    Structures were constructed on the surfaces with an ultrafast laser which uses picosecond or femtosecond laser pulse to remove materials with minimum thermal effect and high precision. This minimizes the degradation of the CIF material under high temperature. However,the downside is that the ablated material can be trapped in the small gap,which prevents further ablation in the depth. After several attempts, it seems that the maximum structure depth under reasonable processing time would be around 0.5 mm. Therefore,two sets of surface structures(1)a=1.5 mm,d=0.5 mm,c=0.9 and(2)a=1.0 mm,d=0.5 mm,c=0.9 were separately constructed on the two surfaces,as shown in Figs.11(a)and 11(b). An optical microscope with large depth-of-field capability was used to measure the geometries of the manufactured structures, as shown in Figs.11(c)and 11(d). Finally,the reflection loss of the structured surfaces was measured at the end.

    Fig.11.(a)and(c)Pictures of 1.5 mm unit cell sample and its geometry measurement. (b) and (d) Pictures of 1.0 mm unit cell sample and its geometry measurement.

    5.2. Result and discussion

    The three reflection loss curves are shown in Fig. 12.The curve of the the CIF composite slab has a peak value of-17.5 dB at 6.08 GHz,and the-10 dB absorption bandwidth is 3.8 GHz. After the surface was covered by copper film,the reflection loss is around 0 dB,indicating that microwaves was fully reflected.

    Fig.12. Reflection loss curves of different surface structure and treatment.

    As structures were manufactured on the surface, microwaves can once again enter the CIF composite. When the size of unit cell is 1.5 mm, the absorption peak moves to 5.52 GHz and the intensity of the peak increases to-19.4 dB.However, the high frequency performance is impaired and the-10 dB absorption bandwidth is decreased to 3.12 GHz,which is probably due to the lack of structure depth and large FSS pattern size as discussed previously. Since the structure depth is difficult to further increase, the size of unit cell is set to be 1.0 mm in the second set of parameters. As shown in Fig. 12, whena=1.0 mm the absorption peak shifts to a higher frequency at 6.92 GHz with a peak value-16.7 dB.While the low frequency performance is affected,the high frequency performance is comparable to that of the CIF composite slab. The-10 dB absorption bandwidth is broadened by 8.1%,to 4.12 GHz.

    The above experiment only serves as a demonstration.It shows that surface structure can be used to tune the radar absorption performance,increasing the absorption bandwidth when the surface is mostly covered by low-emissivity metal film. It also shows that some changing trends can be captured by the model.

    More systematic experiments are required in the future to verify this conceptual design. Nevertheless, many obstacles are on its way to practical application. In the presented experiment,copper was used as the low emissivity material,[2]which is prone to be oxidized under elevated temperature, causing significantly higher emissivity. Although noble metals such as gold and platinum could maintain low emissivity at high temperature,particle erosion under flight conditions could remove the soft metals in a short time. This may require hard and infrared transparent film on the top to protect the noble metals. Also,the size of applied workpiece is limited by vacuum chamber size of PVD equipment. Manufacturing patches or using other metal spraying technology could be practical approaches to this problem. Also, more comprehensive experiments are required to ensure that base material properties are unaffected during the process. In the presented experiment, we took more than 3 hours to manufacture structures on a 180×180 mm surface using ultrafast laser technology.One solution for large-scale production could be imprinting the CIF composite using metal mold before the resin is fully cured.Metal deposition with mask could replace the laser processing in constructing FSS pattern.

    6. Conclusions

    A radar-infrared stealth surface has been designed. Its radar-infrared compatibility and broadband radar absorption are achieved by means of surface patterning. The RAM structure and the FSS pattern govern the surface radar absorption.Influences of structure and pattern geometries on reflection loss are studied by a developed transmission-line-based model along with finite element analysis. They are summarized as follows:

    (1)The developed TLM is capable of capturing variations in radar absorbing performance qualitatively. The omission of diffraction mechanism and the inaccurate representation of the structured layer lead to large deviation from the FEM results especially in high frequency range.

    (2) Decrease in pattern size, increase in structure depth and decrease in ratio of pattern size to unit cell size lead to improved reflection loss in high frequency range and reduced performance in low frequency range.The absorption peak also shifts to a higher frequency.

    (3)Increased pattern size can significant reduce the reflection loss in high frequency, as the FSS layer becomes more reflective to high frequency microwave. An intense absorption peak may be found at a low frequency,which means that proper FSS could be used to improve the reflection loss in low frequency.

    Optimization was conducted to maximize the-10 dB absorption bandwidth. An optimized solution is found near the pointa=0.58 mm,d=1.08 mm andc=0.87, which leads to a 10.1 GHz absorption bandwidth, more than two times of the unstructured RAM. An experiment is conducted to determine the capability of structure design in tuning the overall radar-infrared compatibility.

    猜你喜歡
    余慶
    基于DBSE-Net的大田稻穗圖像分割
    胖姑娘的愛情靈藥
    中外文摘(2021年18期)2021-11-05 12:34:22
    胖姑娘的愛情靈藥
    意林(2021年9期)2021-05-28 13:47:38
    護身符
    雜文選刊(2021年3期)2021-03-12 03:28:55
    護身符
    金秋(2018年21期)2018-03-23 05:37:16
    護身符
    護身符
    喜劇世界(2017年13期)2017-12-05 23:11:35
    特殊護身符
    護身符
    小小說月刊(2017年8期)2017-08-14 12:17:09
    特殊護身符
    特別健康(2017年10期)2017-07-14 08:40:37
    av国产精品久久久久影院| 狠狠狠狠99中文字幕| 麻豆国产av国片精品| av又黄又爽大尺度在线免费看| 99精品在免费线老司机午夜| 午夜视频精品福利| 亚洲成人国产一区在线观看| 午夜福利在线观看吧| av又黄又爽大尺度在线免费看| 久久精品国产综合久久久| 亚洲国产成人一精品久久久| 蜜桃在线观看..| 欧美精品人与动牲交sv欧美| www.精华液| 国产精品久久久久成人av| 国产深夜福利视频在线观看| 成在线人永久免费视频| 精品国产一区二区久久| 欧美乱码精品一区二区三区| 十八禁高潮呻吟视频| 在线天堂中文资源库| 久久免费观看电影| 国产高清videossex| 热99国产精品久久久久久7| 97在线人人人人妻| 人人妻人人澡人人爽人人夜夜| 欧美日韩福利视频一区二区| 看免费av毛片| 91字幕亚洲| 十八禁网站免费在线| 嫁个100分男人电影在线观看| 老司机福利观看| 夜夜骑夜夜射夜夜干| 人人妻,人人澡人人爽秒播| 啦啦啦 在线观看视频| 欧美精品一区二区免费开放| 精品国内亚洲2022精品成人 | 91精品国产国语对白视频| 动漫黄色视频在线观看| 日本黄色日本黄色录像| 后天国语完整版免费观看| 国产人伦9x9x在线观看| 国产日韩欧美视频二区| 亚洲av美国av| 成年人黄色毛片网站| 久久国产精品人妻蜜桃| 999久久久精品免费观看国产| 国产不卡av网站在线观看| 亚洲黑人精品在线| 2018国产大陆天天弄谢| 国产亚洲av高清不卡| 精品人妻在线不人妻| cao死你这个sao货| 国产精品欧美亚洲77777| 国产精品久久久久久精品电影小说| 天天影视国产精品| 日韩人妻精品一区2区三区| 成人三级做爰电影| www日本在线高清视频| 国产在线观看jvid| 天天操日日干夜夜撸| 2018国产大陆天天弄谢| 国产亚洲一区二区精品| 亚洲精品国产精品久久久不卡| 国产av又大| 欧美久久黑人一区二区| 亚洲熟女毛片儿| 国产精品国产av在线观看| 麻豆av在线久日| 久久久精品94久久精品| 999久久久精品免费观看国产| www.999成人在线观看| 亚洲天堂av无毛| 国产av国产精品国产| 老熟妇仑乱视频hdxx| 国产午夜精品久久久久久| 国产欧美日韩一区二区精品| 91精品国产国语对白视频| 亚洲av成人不卡在线观看播放网| 51午夜福利影视在线观看| 少妇的丰满在线观看| 日韩免费高清中文字幕av| 国产男靠女视频免费网站| 精品国产一区二区三区久久久樱花| 日韩一卡2卡3卡4卡2021年| 亚洲av成人一区二区三| 搡老岳熟女国产| 男女免费视频国产| 国产激情久久老熟女| 少妇 在线观看| kizo精华| 美女主播在线视频| 精品久久久精品久久久| 久久狼人影院| 久久九九热精品免费| 日本av手机在线免费观看| 老司机靠b影院| 岛国毛片在线播放| 欧美黄色淫秽网站| 岛国在线观看网站| 久久av网站| 中文欧美无线码| 精品国内亚洲2022精品成人 | 国产亚洲精品第一综合不卡| 肉色欧美久久久久久久蜜桃| 夫妻午夜视频| 女人被躁到高潮嗷嗷叫费观| 老司机影院毛片| 十分钟在线观看高清视频www| 免费在线观看视频国产中文字幕亚洲| 精品一区二区三卡| 久久免费观看电影| 国产成人免费无遮挡视频| 精品亚洲乱码少妇综合久久| 天天操日日干夜夜撸| 亚洲精品国产色婷婷电影| 动漫黄色视频在线观看| 美女高潮到喷水免费观看| 精品久久久久久电影网| 国产老妇伦熟女老妇高清| 久热这里只有精品99| 国产精品偷伦视频观看了| 日本av手机在线免费观看| 日韩制服丝袜自拍偷拍| 人成视频在线观看免费观看| 免费在线观看日本一区| 日韩欧美国产一区二区入口| 欧美精品一区二区大全| 99精品在免费线老司机午夜| 精品高清国产在线一区| 欧美+亚洲+日韩+国产| 91av网站免费观看| 黄色丝袜av网址大全| 亚洲中文字幕日韩| 午夜福利在线免费观看网站| 国产精品欧美亚洲77777| 精品国产亚洲在线| 久久中文字幕一级| 国产单亲对白刺激| 国产亚洲av高清不卡| 亚洲熟妇熟女久久| 亚洲综合色网址| 黑人巨大精品欧美一区二区mp4| 深夜精品福利| 操美女的视频在线观看| 久热爱精品视频在线9| 国产欧美日韩精品亚洲av| 亚洲国产av影院在线观看| 免费日韩欧美在线观看| 亚洲视频免费观看视频| 后天国语完整版免费观看| 大片免费播放器 马上看| 一个人免费看片子| 日韩大码丰满熟妇| 美国免费a级毛片| 国产淫语在线视频| 久久精品亚洲av国产电影网| 超碰成人久久| 精品少妇黑人巨大在线播放| 一本—道久久a久久精品蜜桃钙片| 五月天丁香电影| 久久天堂一区二区三区四区| 无人区码免费观看不卡 | 18在线观看网站| 看免费av毛片| 午夜福利乱码中文字幕| 制服诱惑二区| 老熟妇乱子伦视频在线观看| 国产在线免费精品| 夫妻午夜视频| 国产亚洲精品第一综合不卡| 日本av免费视频播放| 午夜91福利影院| 一区福利在线观看| 国产极品粉嫩免费观看在线| 国产精品99久久99久久久不卡| 一本一本久久a久久精品综合妖精| 日本一区二区免费在线视频| 国产精品99久久99久久久不卡| 十八禁网站网址无遮挡| 午夜久久久在线观看| 久久久久久免费高清国产稀缺| videosex国产| 亚洲综合色网址| 亚洲精品在线美女| 男女之事视频高清在线观看| 日日摸夜夜添夜夜添小说| 少妇精品久久久久久久| 欧美精品一区二区免费开放| 一本综合久久免费| 宅男免费午夜| 久久久久视频综合| 女人被躁到高潮嗷嗷叫费观| 一边摸一边抽搐一进一小说 | 黑人巨大精品欧美一区二区蜜桃| 1024视频免费在线观看| 美国免费a级毛片| 欧美老熟妇乱子伦牲交| 色综合欧美亚洲国产小说| 精品国产超薄肉色丝袜足j| 亚洲人成77777在线视频| 欧美另类亚洲清纯唯美| 女人高潮潮喷娇喘18禁视频| 久久九九热精品免费| 午夜福利影视在线免费观看| 一本一本久久a久久精品综合妖精| 女人精品久久久久毛片| 欧美亚洲日本最大视频资源| 久久人妻福利社区极品人妻图片| 我的亚洲天堂| 欧美黑人精品巨大| 热99re8久久精品国产| 手机成人av网站| 成年人免费黄色播放视频| 国产单亲对白刺激| 蜜桃国产av成人99| 亚洲一区二区三区欧美精品| 高清欧美精品videossex| 亚洲第一青青草原| 老司机福利观看| 女人被躁到高潮嗷嗷叫费观| 18在线观看网站| 国产亚洲精品一区二区www | 亚洲熟女精品中文字幕| 老司机在亚洲福利影院| 亚洲性夜色夜夜综合| 国产精品一区二区在线不卡| 国产xxxxx性猛交| 久9热在线精品视频| 久久久久网色| 日韩欧美免费精品| 成人精品一区二区免费| 99精品欧美一区二区三区四区| 欧美黄色淫秽网站| 成人国产一区最新在线观看| 久久精品亚洲av国产电影网| 国产老妇伦熟女老妇高清| 亚洲精品粉嫩美女一区| 亚洲精品国产一区二区精华液| 好男人电影高清在线观看| av网站免费在线观看视频| 少妇猛男粗大的猛烈进出视频| 国产高清激情床上av| 久久这里只有精品19| 亚洲五月色婷婷综合| 国产av精品麻豆| 国产在线精品亚洲第一网站| 精品一品国产午夜福利视频| 十分钟在线观看高清视频www| 国产一区二区三区视频了| 天堂中文最新版在线下载| 黄色怎么调成土黄色| 美女午夜性视频免费| 欧美人与性动交α欧美精品济南到| 老司机亚洲免费影院| 五月开心婷婷网| 中文字幕最新亚洲高清| 久久亚洲精品不卡| 国产单亲对白刺激| 成人国产一区最新在线观看| 欧美日韩成人在线一区二区| 757午夜福利合集在线观看| 国产三级黄色录像| 淫妇啪啪啪对白视频| 日韩视频在线欧美| 少妇的丰满在线观看| 午夜精品国产一区二区电影| 香蕉国产在线看| 美女国产高潮福利片在线看| 午夜福利在线免费观看网站| 国产1区2区3区精品| a级片在线免费高清观看视频| 亚洲精品乱久久久久久| 好男人电影高清在线观看| 十八禁人妻一区二区| 无限看片的www在线观看| 天堂动漫精品| 亚洲情色 制服丝袜| 久久国产精品男人的天堂亚洲| 亚洲人成电影免费在线| 黄色 视频免费看| 中亚洲国语对白在线视频| 丰满少妇做爰视频| 免费高清在线观看日韩| 真人做人爱边吃奶动态| 国产欧美亚洲国产| 天堂8中文在线网| 日韩精品免费视频一区二区三区| aaaaa片日本免费| 在线观看www视频免费| 高清黄色对白视频在线免费看| 高潮久久久久久久久久久不卡| 波多野结衣av一区二区av| 亚洲人成电影免费在线| 飞空精品影院首页| 欧美乱妇无乱码| 水蜜桃什么品种好| 久久人妻福利社区极品人妻图片| 欧美日韩国产mv在线观看视频| 国产在线视频一区二区| 91老司机精品| 亚洲精品一二三| 欧美日韩亚洲国产一区二区在线观看 | 99国产精品99久久久久| 成年人免费黄色播放视频| 国产aⅴ精品一区二区三区波| 久久久国产欧美日韩av| 99久久国产精品久久久| 大型黄色视频在线免费观看| 免费在线观看黄色视频的| 日韩一区二区三区影片| 亚洲人成电影观看| 亚洲五月色婷婷综合| 人成视频在线观看免费观看| 亚洲午夜精品一区,二区,三区| 极品教师在线免费播放| 在线观看舔阴道视频| 啦啦啦 在线观看视频| 欧美久久黑人一区二区| 1024香蕉在线观看| 法律面前人人平等表现在哪些方面| 免费黄频网站在线观看国产| 性少妇av在线| av线在线观看网站| 无人区码免费观看不卡 | 成人国产av品久久久| 99热国产这里只有精品6| 热re99久久精品国产66热6| 亚洲精华国产精华精| 久久久久网色| 久久亚洲真实| 老司机亚洲免费影院| 精品国产乱码久久久久久男人| 亚洲精品av麻豆狂野| 深夜精品福利| 亚洲精品久久午夜乱码| 欧美日本中文国产一区发布| 一级毛片女人18水好多| www.999成人在线观看| 久久热在线av| 欧美黑人欧美精品刺激| 国产高清国产精品国产三级| 国产91精品成人一区二区三区 | 精品人妻熟女毛片av久久网站| av天堂久久9| 久久久欧美国产精品| 熟女少妇亚洲综合色aaa.| 丁香六月天网| 国产精品亚洲av一区麻豆| 丝瓜视频免费看黄片| 国产欧美日韩综合在线一区二区| 久久久久久人人人人人| 国产国语露脸激情在线看| 欧美亚洲日本最大视频资源| 久久午夜亚洲精品久久| 黄色 视频免费看| 如日韩欧美国产精品一区二区三区| 侵犯人妻中文字幕一二三四区| 亚洲国产欧美一区二区综合| 欧美日韩精品网址| 这个男人来自地球电影免费观看| 国产亚洲av高清不卡| 亚洲一区二区三区欧美精品| 建设人人有责人人尽责人人享有的| 亚洲精品自拍成人| 亚洲熟女毛片儿| 高清毛片免费观看视频网站 | 国产片内射在线| h视频一区二区三区| 精品午夜福利视频在线观看一区 | 精品国产一区二区久久| 男女午夜视频在线观看| 欧美黄色淫秽网站| 亚洲国产看品久久| www.熟女人妻精品国产| 蜜桃在线观看..| 国产aⅴ精品一区二区三区波| 18禁国产床啪视频网站| 黄色a级毛片大全视频| 亚洲成人国产一区在线观看| 淫妇啪啪啪对白视频| www.999成人在线观看| 一级毛片女人18水好多| 久久久国产精品麻豆| 真人做人爱边吃奶动态| 俄罗斯特黄特色一大片| 老司机亚洲免费影院| 久久99一区二区三区| 岛国在线观看网站| 久久精品成人免费网站| 国产一区二区三区视频了| 成人黄色视频免费在线看| 欧美日韩黄片免| 欧美成狂野欧美在线观看| 国产无遮挡羞羞视频在线观看| 欧美日韩视频精品一区| 美女视频免费永久观看网站| 国产国语露脸激情在线看| 日韩欧美国产一区二区入口| 久久久久视频综合| 99re在线观看精品视频| 亚洲欧洲日产国产| 国产不卡av网站在线观看| 两个人看的免费小视频| 久久久水蜜桃国产精品网| 啦啦啦在线免费观看视频4| 日韩三级视频一区二区三区| 亚洲中文日韩欧美视频| 丝袜美腿诱惑在线| 五月天丁香电影| 久久亚洲真实| 妹子高潮喷水视频| av福利片在线| 在线观看人妻少妇| 国产激情久久老熟女| 他把我摸到了高潮在线观看 | 90打野战视频偷拍视频| 国产亚洲精品一区二区www | 国产激情久久老熟女| 另类亚洲欧美激情| 高潮久久久久久久久久久不卡| 大香蕉久久网| 又黄又粗又硬又大视频| 久久亚洲真实| 国产一区二区三区视频了| 免费在线观看黄色视频的| 日本五十路高清| 日韩大片免费观看网站| 两个人免费观看高清视频| 久久人妻av系列| 91精品三级在线观看| 日日爽夜夜爽网站| 丝袜美腿诱惑在线| 欧美精品亚洲一区二区| 国产黄频视频在线观看| 亚洲 国产 在线| 最新在线观看一区二区三区| 欧美黑人精品巨大| 黄色怎么调成土黄色| 午夜福利免费观看在线| 757午夜福利合集在线观看| 久久天躁狠狠躁夜夜2o2o| 激情视频va一区二区三区| 99香蕉大伊视频| 国产精品影院久久| 久久久久国产一级毛片高清牌| 成年动漫av网址| 国产日韩一区二区三区精品不卡| 五月开心婷婷网| 一本大道久久a久久精品| 亚洲一码二码三码区别大吗| 在线观看免费视频日本深夜| 一区在线观看完整版| 久久人人97超碰香蕉20202| 两人在一起打扑克的视频| 亚洲第一av免费看| 成人18禁高潮啪啪吃奶动态图| 日韩三级视频一区二区三区| 美国免费a级毛片| 久久亚洲真实| 欧美 日韩 精品 国产| 操美女的视频在线观看| 久久精品aⅴ一区二区三区四区| 久久热在线av| 黑丝袜美女国产一区| 激情在线观看视频在线高清 | 国产97色在线日韩免费| 男女无遮挡免费网站观看| 最新美女视频免费是黄的| av有码第一页| 久久久久网色| 后天国语完整版免费观看| 人人妻,人人澡人人爽秒播| 久久久国产一区二区| 日韩欧美三级三区| 精品国内亚洲2022精品成人 | 欧美 亚洲 国产 日韩一| 久久亚洲真实| 午夜视频精品福利| 亚洲国产欧美在线一区| 一本一本久久a久久精品综合妖精| 亚洲中文日韩欧美视频| 欧美精品一区二区大全| 国产成人欧美| 老司机午夜福利在线观看视频 | 91麻豆av在线| a级片在线免费高清观看视频| 91精品国产国语对白视频| 精品免费久久久久久久清纯 | 欧美激情 高清一区二区三区| av国产精品久久久久影院| 精品国产乱码久久久久久男人| 国产精品免费视频内射| 18禁黄网站禁片午夜丰满| 欧美精品高潮呻吟av久久| 久久午夜综合久久蜜桃| 精品久久久久久久毛片微露脸| 女性被躁到高潮视频| 国产色视频综合| 新久久久久国产一级毛片| 亚洲欧洲日产国产| 美女高潮到喷水免费观看| 久久精品亚洲熟妇少妇任你| 欧美精品一区二区免费开放| 精品亚洲成国产av| av天堂久久9| 午夜福利在线免费观看网站| 黄色成人免费大全| 日韩有码中文字幕| 一区福利在线观看| 啦啦啦视频在线资源免费观看| 久久精品国产亚洲av高清一级| 一边摸一边做爽爽视频免费| 三级毛片av免费| 欧美黑人精品巨大| 少妇猛男粗大的猛烈进出视频| 满18在线观看网站| 欧美 日韩 精品 国产| 老司机午夜福利在线观看视频 | 亚洲精品国产一区二区精华液| 十八禁网站免费在线| 又黄又粗又硬又大视频| 欧美精品一区二区免费开放| 亚洲国产毛片av蜜桃av| 天堂8中文在线网| 日韩欧美免费精品| 热re99久久精品国产66热6| 久久久久久亚洲精品国产蜜桃av| 欧美激情 高清一区二区三区| 亚洲欧美一区二区三区久久| 丝袜人妻中文字幕| 亚洲av成人不卡在线观看播放网| 丰满人妻熟妇乱又伦精品不卡| 日韩熟女老妇一区二区性免费视频| 色婷婷久久久亚洲欧美| 亚洲一卡2卡3卡4卡5卡精品中文| 精品国产一区二区三区四区第35| 亚洲欧美日韩高清在线视频 | 一区二区三区激情视频| 成人国产av品久久久| 久久人妻av系列| 久久精品人人爽人人爽视色| 下体分泌物呈黄色| 欧美日韩福利视频一区二区| 国产高清激情床上av| 91精品国产国语对白视频| 老鸭窝网址在线观看| 女人被躁到高潮嗷嗷叫费观| 亚洲精品国产一区二区精华液| 国产在线免费精品| 亚洲精品一卡2卡三卡4卡5卡| 中文字幕人妻熟女乱码| 午夜福利乱码中文字幕| 精品少妇内射三级| 汤姆久久久久久久影院中文字幕| 男人舔女人的私密视频| 男女高潮啪啪啪动态图| 亚洲性夜色夜夜综合| 亚洲欧美激情在线| 无人区码免费观看不卡 | 在线观看免费高清a一片| 母亲3免费完整高清在线观看| 999久久久国产精品视频| 色尼玛亚洲综合影院| 成人亚洲精品一区在线观看| 国产亚洲av高清不卡| 十分钟在线观看高清视频www| 深夜精品福利| 成年人午夜在线观看视频| 亚洲天堂av无毛| 日韩精品免费视频一区二区三区| 99国产精品99久久久久| 丝袜人妻中文字幕| 欧美精品高潮呻吟av久久| av国产精品久久久久影院| 久久久久久久久久久久大奶| 丰满饥渴人妻一区二区三| 菩萨蛮人人尽说江南好唐韦庄| 欧美变态另类bdsm刘玥| 国产亚洲精品一区二区www | 日本av手机在线免费观看| cao死你这个sao货| 国产深夜福利视频在线观看| 国产aⅴ精品一区二区三区波| 免费观看av网站的网址| 黄色 视频免费看| 夫妻午夜视频| 国产有黄有色有爽视频| 精品国产亚洲在线| 欧美日韩亚洲国产一区二区在线观看 | 免费黄频网站在线观看国产| 日本av手机在线免费观看| 欧美精品人与动牲交sv欧美| 人人妻,人人澡人人爽秒播| 久久热在线av| 纵有疾风起免费观看全集完整版| 大型黄色视频在线免费观看| 欧美大码av| 狠狠婷婷综合久久久久久88av| 免费在线观看影片大全网站| svipshipincom国产片| 老司机影院毛片| 亚洲精品国产区一区二| av网站在线播放免费| 久久精品人人爽人人爽视色| 天堂俺去俺来也www色官网| 人妻久久中文字幕网| 精品久久久久久久毛片微露脸| 热re99久久精品国产66热6| 熟女少妇亚洲综合色aaa.| 成在线人永久免费视频| 老司机靠b影院| 国产高清videossex| 51午夜福利影视在线观看| 自线自在国产av|