• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Enhanced mechanical properties of mortar with graphene in the traditional sandstone cultural relics conservation

    2021-03-06 02:46:02,,,2,,2,,

    , , ,2, ,2, ,

    1.Northwest Research Institute Co.Ltd. of C.R.E.C., Lanzhou 730000, P. R. China; 2.School of Civil Engineering and Mechanics, Lanzhou University, Lanzhou 730000, P. R. China; 3. Leshan Giant Buddha Management Committee, Leshan 614003, Sichuan, P. R. China)

    Abstract: More than 8 000 grottoes and cliff statues are located in Sichuan and Chongqing. Most are made from sandstone. The sandstone has deteriorated due to long-term environmental effects, posing a threat to the cultural relics. Graphene sheets are added to the traditional mortar of the sandstone cultural relics to enhance the properties, which is defined as “CH@G mortar”. The mechanical properties and volume stability of the CH@G mortar are enhanced by the graphene sheets. The highest strength is obtained by the addition of 0.07% graphene sheets, and its values (increased proportion compared with CH mortar) of compressive strength, flexural strength and tensile strength at 56 d are 4.21 MPa (7.36 %), 2.21 MPa (19.46%) and 0.47 MPa (51.61%), respectively. The FT-IR and Raman spectra results show that the graphene sheets have little influence on the composition of the products, and could accelerate the hydration in the early days, according to the XRD results. The SEM images show that graphene sheets could form a uniform and compacted microstructure.

    Keywords:sandstone cultural relics; mortar; graphene; mechanical properties

    1 Introduction

    There are more than 8 000 grottoes and cliff statues located in Sichuan and Chongqing. These are mainly carved out of the thick sandstone and mudstone strata of the Jurassic Period of the Mesozoic Era. The most famous stone cultural relics are the Leshan Giant Buddha and the Dazu rock carvings[1]. The sandstone cultural relics have deteriorated over time due to both environmental causes and human activity, and conservation work has been carried out several times in the past decades in an effort to preserve them[2]. In 2001, Chinese experts used traditional materials to repair the head, chest and abdomen of the Leshan Giant Buddha.

    The mortar used for the conservation of traditional sandstone cultural relics is a cementitious material composed of lime, sand, slag and a small amount of cement. Cementitious materials possess relatively high compressive strength, but lack toughness and volume stability[3-5]. The traditional materials used in the chest and abdomen areas of the Leshan Giant Buddha show some deterioration due to multiple factors. The deterioration of the chest and abdomen (exfoliation, hollow, crack and water infiltration) is shown in Fig.1.

    Fig.1 Schematic images showing deterioration of Leshan

    Graphene, which has a high elastic modulus (1 TPa) and excellent mechanical properties (130 GPa)[6-10], is considered an ideal candidate for improving the mechanical properties of cementitious material, and previous results indicate that adding graphene to cementitious matrices can enhance the toughness of the resultant composites[11-15].

    In this paper, traditional mortar used in the conservation of sandstone cultural relics is named CH mortar due to its Chinese name “Chui Hui”. Graphene is used to improve their mechanical properties, and the mortars with graphene are defined as CH@G mortars. Mechanical properties, shrinkage rate, ultrasonic wave velocity, the composition of the products, morphology and the mechanism of the graphene effect are investigated.

    2 Experimental Section

    2.1 Materials

    2.1.1 CH mortar

    The raw materials of the CH mortar were lime, slag, sand and a small amount of cement. Mixing and ramming were employed to make the particles distribute uniformly.

    The cement and lime were local products. The X-Ray Diffraction (XRD) results are shown in Table 1. The sand was purchased from Xiamen ISO Standard Sand Co, Ltd.. The slag, which was steel mill waste, was purchased from Desheng Steel Co., Ltd. in Leshan. The particle size distribution curves of the slag and sand are shown in Fig.2.

    Fig.2 Particle size distribution curves of slag and

    Table 1 XRD Semi-quantitative analysis of cement and lime

    2.1.2 Graphene

    Graphene sheets was purchased from Deyang Carbonene Co. in Sichuan province. The microstructure and chemical composition were tested by Transmission Electron Microscope (TEM), High Resolution Transmission Electron Microscope (HRTEM) and X-ray Photoelectron Spectroscopy (XPS). As shown in Fig.3 (a), the microstructure of graphene is similar to overlapping nano-fibers. Fig.3 (b) shows the HRTEM image of the graphene sheet. The sheet has 6~7 single carbon layers. As shown in Fig.3 (c), the intensity of the C1s peak is greater than that of the O1s peak. The C1s spectrum contains four peaks, including peak A (C=C) at 284.4 eV, peak B (C—O) at 286.9 eV, peak C (C=O) at 287.7 eV, and peak D (COOH) at 288.8 eV.

    Fig.3 (a)TEM, (b)HRTEM images and (c)XPS

    2.2 Specimen preparation

    The preparation procedureis illustrated in Fig.4. First, graphene and hexadecyl trimethyl ammonium bromide (CTAB) were dispersed into 50 mL deionized water and ultrasonicated for 10 min. Next, cement and lime were mixed and stirred, and slag and sand were added after 1 min of low speed stirring. Finally, the graphene dispersion was dropped into the CH mortar. Ramming was employed to make the particle distribution more uniform after mixing. The mixture was molded to different types of specimens for testing and characterization.

    Table 2 presents the recipes for preparations of various CH and CH@G mortars. The weight percentages of the graphene sheets in the mortars were 0.01%, 0.03%, 0.05%, 0.07% and 0.10% of all raw materials (lime, cement, slag and sand). The water binder ratios of all specimens were 0.30. The size of the samples for compressive strength was 70.7 mm×70.7 mm×70.7 mm, and the flexural strength test samples were 40 mm×40 mm×160 mm. The Brazilian disc test was used to test the tensile strength of the samples, and the size of the samples was φ50 mm×100 mm.

    Table 2 Recipes of CH and CH@G mortars

    All samples for testing and characterization were cured in an environment (parameters: 8:00—20:00, 20 ℃, RH 65%, 20:00—8:00, 15 ℃, RH 75%) similar to that of the Leshan Giant Buddha area, and the parameters of the curing condition were controlled by a temperature and humidity curing box (BG/TH-100, Shanghai Bogong Equipment Co. Ltd.).

    2.3 Experimental methods

    2.3.1 Shrinkage rate and ultrasonic wave velocity

    The shrinkage rate of the specimens (40 mm×40 mm×160 mm) at different ages was measured by an electronic micrometer with an accuracy of 0.001 mm. The ultrasonic wave velocity of the samples (φ=50 mm, height=100 mm) at different ages was obtained by an RSM-SY5 (T) nonmetal acoustic detector.

    2.3.2 Mechanical properties

    Compressive strength, flexural strength and tensile strength were tested on a universal mechanical testing machine.The flexural strength of 40 mm×40 mm×160 mm samples was determined with a central-loading method, and then the compressive strength test was conducted after the flexural test on the remaining samples. The rate of loading was 2 mm/min. All test results were the average value of three replicate samples.

    2.3.3 Characterization

    The microstructure of all samples was examined by scanning electron microscope (Hitachi S-4800, Japan) and transmission electron microscope (Hillsboro, Tecnai G2 F20). Chemical state assignment was performed using X-ray photoelectron spectroscopy (Waltham, Thermal Scientific Escalab 250 Xi). Surface characterizations of specimens were obtained by FT-IR spectra analysis (Bruker, Tensor 27), Raman spectra analysis (France, LabRAM HR) and X-ray diffraction (Rigaku, D/max-2400).

    3 Results and discussion

    3.1 Shrinkage rate

    The shrinkage rates of all samples are shown in Fig.5. The shrinkage rate of the CH specimen increases rapidly during 0-7 d, and then slowly increases from 8 d to 14 d. Finally, the value remains almost constant after 15 d. The CH@G specimens show a tendency similar to that of the CH specimen, but all shrinkage rate values are lower than those of the CH specimen, indicating that the addition of grapheme can enhance the volume stability of the CH@G specimens. When percentage of graphene added is 0.07 wt%, the specimen has the lowest shrinkage rate (0.39%) and the attenuation is 34.74% compared to the CH specimen (0.59%).

    Fig.5 Shrinkage rate of specimens at different

    3.2 Ultrasonic wave velocity

    Ultrasonic wave velocity tests were employed to reflect the degree of solidification of the samples[16]. As shown in Fig.6, all specimen values first decrease and then increase. Finally, the value becomes stable. At 0 d, each sample has a high initial value due to the water filling in the pores. During 1-3 d, the water in the pores is absorbed by the cement and lime, and the wave velocity drops rapidly due to the loose and porous microstructure. At 4-14 d, the wave velocity of each specimen is simultaneously improved as the cement and lime solidify, and the velocity value increases as graphene is added. In the last period (15~28 d), the wave velocities become stable. At 28 d, the velocities of the CH@G specimens are higher than those of the CH specimen. The velocity of the CH@G-4 specimen is 1 670 m/s, which is the highest value among all the samples, and the increasement is 15.17% compared to the CH specimen.

    Fig.6 Ultrasonic wave velocity of specimens at different

    3.3 Mechanical properties

    3.3.1 Compressive strength

    As shown in Fig.7, the compressive strength of the CH specimen at 56 d is only 3.94 MPa. The compressive strengths of the CH@G specimens increase with the addition of graphene, and the highest strength is obtained at 0.07 wt%. The strength completion degree is used to describe the hardening rate of each sample. The compressive strength value of each sample at 56 d is used as the reference value in the compressive strength completion degree curve[17]. The hardening rate gets faster in the CH@G specimens. The compressive strength completion degree of the CH and the CH@G specimens (1-5) at 7 d are 52.30%, 60.80%, 62.69%, 65.90%, 66.11% and 65.78%, respectively, suggesting that the addition of graphene could accelerate the hydration of the CH@G specimens in the early days.

    Fig.7 Compressive strength of specimens at 3 d, 7 d, 28 d and 56 d

    3.3.2 Flexural strength

    The flexural strengths are shown in Fig.8. The flexural strengths of the CH specimen are 0.89 MPa (3 d), 1.34 MPa (7 d), 1.60 MPa (28 d) and 1.85 MPa (56 d). With the addition of graphene, the flexural strength at 56 d increased for different degrees and the largest increasement is 19.46% obtained in the CH@G-4 sample. The 56 d flexural strength values of each sample are used as the reference value in the flexural strength completion degree curve. The flexural strength completion degree curve shows a tendency similar to that of the compressive strength completion degree curve. The flexural strength completion degrees at 7 d are 72.40% (CH), 74.71% (CH@G-1), 75.22% (CH@G-2), 76.92% (CH@G-3), 76.94% (CH@G-4), and 76.33% (CH@G-5), indicating that the addition of graphene has the potential to enhance the hydration reaction.

    Fig.8 Flexural strength of specimens at 3 d,7 d, 28 d and 56 d

    3.3.3 Tensile strength

    As shown in Fig.9, the tensile strength of the CH specimen at 3 d, 7 d, 28 d and 56 d are 0.13 MPa, 0.18 MPa, 0.24 MPa, and 0.31 MPa, respectively. The tensile strength of the CH@G specimens increases with the addition of graphene. The CH@G-4 sample exhibits the highest strength value (0.47 MPa), and the increasement is 51.61%. The result shows that the addition of graphene to the CH@G specimens has a significant influence on the tensile strength. The 56 d tensile strength value of each sample is used as the reference value in the tensile strength completion degree curve. The tensile strength completion degree of the CH specimen at 7 d is 58.1%. With the addition of graphene, the tensile strength completion degrees of the CH@G specimens, which are 60.00%, 60.00%, 64.12%, 61.73% and 62.23%, change a little at each dosage of graphene (0.01%, 0.03%, 0.05%, 0.07% and 0.10%).

    Fig.9 Tensile strength of specimens at 3 d, 7 d, 28 d and 56 d

    3.4 Products characteristics

    3.4.1 FT-IR spectra

    The FT-IR spectra of graphene, CH mortar and CH@G mortars at 28 d are presented in Fig.10. As shown in Fig.10, a characteristic broad band that is responsible for hydroxyl stretching can be observed around 3 450 cm-1. The —COOH carbonyl stretching at 1 730 cm-1for graphene is very weak, likely because the absorption is slight and is obscured by the range band of C=C at 1 630 cm-1 [18-19]. The spectra of the CH mortar and the CH@G mortars have similar characteristic peaks such as 3 460 cm-1(—OH), 1 470 cm-1(O—C—O) and 778 cm-1(O—C—O), 950 cm-1(C—S—H) and 510 cm-1(Si—O—Si). The results indicate that the addition of graphene has little influence on the composition of the products. However, the characteristic peaks of graphene can rarely be observed in the FT-IR spectra of the CH@G mortars. The Raman spectra are employed to further analyze the existence of graphene in the CH@G mortars.

    Fig.10 FT-IR spectra of graphene, CH mortar and CH@G

    3.4.2 Raman spectra

    The Raman spectra of graphene, CH mortar and CH@G mortars at 28 d are shown in Fig.11. The spectrum of graphene contains three peaks, namely D peak at 1 350 cm-1, G peak at 1 582 cm-1and 2D peak at 2 700 cm-1. The D peak and 2D peak represent the high-frequency E2gphonon at the center of the Brillouin zone, and the G peak corresponds to the breathing modes of six-atom rings[20]. The spectrum of the CH mortar has four characteristic peaks, including [CO3] bending vibration, [CO3] symmetric stretching vibration, C bending vibration and O bending vibration, and similar characteristic peaks are observed in the spectra of the CH@G mortars. The results confirm that the addition of graphene has little influence on the composition of the products. A weakened peak at 1 550 cm-1, the G peak of graphene, can be observed in the spectra of CH@G-2, CH@G-3, CH@G-4 and CH@G-5, and the intensity of this peak increased as the percentage of graphene added increased. It suggests that the graphene has been successfully added into the CH@G mortars.

    Fig.11 Raman spectra of graphene, CH mortar and

    3.4.3 XRD

    XRD patterns of CH mortar, CH@G-2 mortar and CH@G-4 mortar curing at different ages are shown in Fig.12. The specimens are mainly composed of Ca(OH)2, CaCO3, SiO2, AFt and unhydrated C3S, but C-S-H could not be indexed by XRD due to its amorphous property[21]. The peak intensity of unhydrated C3S can be used to analyze the hydration rate of each sample. As shown in Fig.12 (a), the peak intensity of unhydrated C3S in the CH specimen at 1 d is a little higher than those specimens of CH@G-2 and CH@G-4, indicating that the hydration rate of the CH mortar is equivalent to that of the CH@G-2 and CH@G-4 mortars at the first period (0-1 d). From Fig.12 (b), the peak intensity of unhydrated C3S in the CH specimen at 3 d is much higher than those specimens of CH@G-2 and CH@G-4, and the peak shows a decreasing trend with the increasing contents of graphene. The results suggest that the hydration rate of the CH mortar is much slower than that of the CH@G-2 mortar and the CH@G-4 mortar at the second period (1-3 d). The hydration rate of the CH mortar is slower than that of the CH@G-2 mortar and the CH@G-4 mortar at the third period (3-7 d), as shown in Fig.12 (c). In the fourth period, the peak intensity of the unhydrated C3S in the CH mortar is as great as those of the CH@G-2 mortar and the CH@G-4 mortar.

    Fig.12 XRD patterns of CH mortar, CH@G-2 mortar,and CH@G-4 mortar curing for (a) 1 d (b) 3 d

    The peak of Ca(OH)2at 18° can be used to analyze the amount of Ca(OH)2due to its good crystallinity[22]. The intensity of Ca(OH)2in CH at 1 d is as high as that in the CH@G-2 and CH@G-4, meaning that the hydration rate of each sample is similar to that in first period. The intensity of Ca(OH)2in the CH at 3 d is higher than that in CH@G-2 and CH@G-4, indicating that the hydration rate of the CH@G specimens is quicker than that of the CH specimen. The trend shows a tendency similar to the change of C3S. The results of XRD demonstrate that graphene could enhance the hydration of cement in the early days, leading to higher strength of the CH@G mortars.

    3.5 Product morphology

    As shown in Fig.13 (a), the CH specimen is mainly the crystal aggregation of laminated Ca(OH)2and fibrous C—S—H, and the whole microstructure is loose. Fig.13 (b), (c) show the morphology of the CH@G-2 specimen and the CH@G-3 specimen, and the microstructure of the two specimens is similar to that of the CH specimen. As shown in Fig.13 (d), a small amount of graphene sheets exist between particles, and the microstructure is still loose, indicating that the effect of the graphene is not significant at this content. From Fig.13 (e), graphene sheets can be observed in the CH@G-4 specimen, and the microstructure of the CH@G-4 specimen is more uniform and dense compared with the CH specimen. As shown in Fig.13 (f), more graphene sheets can be observed, but the graphene shows a tendency to agglomerate. It can be concluded that the effect of graphene in the CH@G-5 specimen is

    Fig.13 SEM images of mortars at 28 d

    not more remarkable than that of the CH@G-4 specimen. From the results of EDS (Table 3), the addition of graphene has no significant influence on the composition of the CH@G specimens, according to the results of FT-IR, Raman and XRD. The results of SEM and EDS suggest that a sprinkling of graphene can control the shape and arrangement of the products in the CH@G specimens.

    Table 3 EDS data of marked area in SEM images

    3.6 Mechanism analysis

    According to the experimental results and the discussion above, the possible mechanism by which the addition of graphene influences the mechanical properties of CH mortar can be illustrated as follows (Fig.14). In the hydration process, a complex reaction is carried out among C2S, C3S, C3A and C4AF. The products of hydration are AFt, AFm, Ca(OH)2and C—S—H. The corresponding reactions are expressed by Eqs. (1)~(4).

    Ca3Al2O6(C3A)+3CaSO4·2H2O+26H2O→

    Ca6Al2(SO4)3(OH)12·26H2O (AFt)

    (1)

    2Ca3Al2O6(C3A)+

    Ca6Al2(SO4)3(OH)12·26H2O(AFt)+4H2O→

    3Ca4Al2(OH)12·SO4·6H2O(AFm)

    (2)

    2Ca3SiO5(C3S)+6H2O→

    3CaO·2SiO2·4H2O(C—S—H)+3Ca(OH)2

    (3)

    2Ca2SiO4(C2S)+4H2O→

    3CaO·2SiO2·4H2O(C—S—H)+Ca(OH)2

    (4)

    Fig.14 Mechanism by which graphene influences the

    Graphene sheets involve active groups (—OH, —COOH, and —SO3H) after being functionalized by CTAB, and acid-based reactions take place between these active groups and Ca(OH)2, leading to a strong covalent force on the interface between the graphene and the CH matrix[6]. The reaction sites and patterns are simultaneously controlled by the graphene, which is called the template effect[23]. The products of hydration grow forward from the surface of the graphene in the same direction, exhibit in an ordered way, and form a uniform and compacted microstructure. The resultant products improve the strength and volume stability of the CH@G mortars. Once the microstructure starts to crack or lose stability, they would disperse into the pores and cracks as filler to retard crack propagation.

    4 Conclusion

    Grapheneis used to enhance the mechanical properties of CH@G mortars in this study. With the increase of graphene sheets, the mechanical properties of the CH@G mortars are enhanced. The specimen with the highest strength is found at 0.07 wt% level of graphene addition, where the compressive strength, flexural strength and tensile strength at 56 d are 4.21 MPa, 2.21 MPa and 0.47 MPa, respectively. FT-IR and Raman spectra show that the addition of graphene has little influence on the composition of the products, and from the XRD results, the graphene could enhance the hydration in the early days.

    Acknowledgements

    The authors would like to acknowledge the financial support from the Sichuan Science and Technology Program (No. 2020YFS0391) and Key Research Project of China Railway Academy Co. Ltd. (No. 2019-KJ011-Z010-A2, No. 2020-KJ009-Z009-A2).

    最新在线观看一区二区三区| 国产精品日韩av在线免费观看| 亚洲中文字幕一区二区三区有码在线看| 国产熟女xx| 怎么达到女性高潮| 别揉我奶头 嗯啊视频| 老司机午夜十八禁免费视频| 国产精华一区二区三区| 狠狠狠狠99中文字幕| www.999成人在线观看| 亚洲国产精品sss在线观看| 国产一区二区三区视频了| 国语自产精品视频在线第100页| 日韩欧美在线乱码| 久久精品国产亚洲av天美| 桃色一区二区三区在线观看| 午夜免费激情av| 欧美性猛交╳xxx乱大交人| 99热只有精品国产| 少妇被粗大猛烈的视频| 亚洲精品在线观看二区| 国产免费一级a男人的天堂| 亚洲色图av天堂| 91在线观看av| 成人欧美大片| 亚洲三级黄色毛片| 午夜日韩欧美国产| 日日摸夜夜添夜夜添小说| 看片在线看免费视频| 少妇人妻精品综合一区二区 | 一级黄色大片毛片| 人妻丰满熟妇av一区二区三区| 欧美黄色淫秽网站| 男人和女人高潮做爰伦理| 日本a在线网址| 亚洲熟妇中文字幕五十中出| 国产真实伦视频高清在线观看 | 国内精品一区二区在线观看| 亚洲avbb在线观看| 日韩有码中文字幕| 欧美成人a在线观看| 88av欧美| 亚洲精品成人久久久久久| 色哟哟哟哟哟哟| 熟妇人妻久久中文字幕3abv| 老师上课跳d突然被开到最大视频 久久午夜综合久久蜜桃 | 一个人免费在线观看电影| 一区福利在线观看| 亚洲中文字幕一区二区三区有码在线看| 色视频www国产| 性插视频无遮挡在线免费观看| 乱人视频在线观看| 久久久成人免费电影| 免费看a级黄色片| 免费无遮挡裸体视频| 韩国av一区二区三区四区| av在线老鸭窝| 精品日产1卡2卡| x7x7x7水蜜桃| 国产精华一区二区三区| 夜夜爽天天搞| 欧美性感艳星| 国产精品三级大全| 亚洲av.av天堂| 精品人妻1区二区| 国产一区二区在线观看日韩| 12—13女人毛片做爰片一| 波野结衣二区三区在线| 日韩国内少妇激情av| 精品久久久久久久人妻蜜臀av| 国产在视频线在精品| 成熟少妇高潮喷水视频| 首页视频小说图片口味搜索| 麻豆成人午夜福利视频| 亚洲五月婷婷丁香| 夜夜爽天天搞| 搡老妇女老女人老熟妇| av欧美777| 亚洲中文字幕日韩| 国产精品电影一区二区三区| 一级av片app| 老鸭窝网址在线观看| 变态另类丝袜制服| 午夜福利欧美成人| 在线天堂最新版资源| 精品国内亚洲2022精品成人| 亚洲人成电影免费在线| 亚洲av电影在线进入| 久久精品国产亚洲av香蕉五月| 精品人妻偷拍中文字幕| 老熟妇乱子伦视频在线观看| 亚洲美女搞黄在线观看 | 757午夜福利合集在线观看| 中文字幕av在线有码专区| 91狼人影院| 韩国av一区二区三区四区| 搞女人的毛片| 欧美精品啪啪一区二区三区| 成人国产综合亚洲| 国产精品一区二区三区四区免费观看 | 啦啦啦韩国在线观看视频| 又黄又爽又刺激的免费视频.| 国产在线精品亚洲第一网站| 欧美一级a爱片免费观看看| 九色国产91popny在线| 国产色爽女视频免费观看| 久久国产精品人妻蜜桃| 中文字幕久久专区| 国产伦精品一区二区三区四那| 日韩精品中文字幕看吧| 中文资源天堂在线| 亚洲,欧美,日韩| 伊人久久精品亚洲午夜| h日本视频在线播放| 国产亚洲精品久久久久久毛片| 亚洲第一区二区三区不卡| 欧美日韩黄片免| 精品人妻偷拍中文字幕| 亚洲精品亚洲一区二区| 91av网一区二区| 国内揄拍国产精品人妻在线| АⅤ资源中文在线天堂| 天堂√8在线中文| 嫩草影院精品99| 一边摸一边抽搐一进一小说| xxxwww97欧美| 老司机午夜福利在线观看视频| 欧美丝袜亚洲另类 | 一本一本综合久久| 99在线视频只有这里精品首页| 亚洲欧美清纯卡通| 一本久久中文字幕| 久久久久国内视频| 性色avwww在线观看| 最近最新免费中文字幕在线| av视频在线观看入口| 舔av片在线| av在线天堂中文字幕| 国产精品自产拍在线观看55亚洲| 88av欧美| 色哟哟·www| 成年女人永久免费观看视频| 国产亚洲欧美在线一区二区| 亚洲内射少妇av| 精品久久国产蜜桃| 丰满乱子伦码专区| 精品久久国产蜜桃| 最近视频中文字幕2019在线8| 露出奶头的视频| 亚洲最大成人av| 午夜亚洲福利在线播放| 亚洲av熟女| 欧美成人一区二区免费高清观看| 99国产精品一区二区蜜桃av| 一二三四社区在线视频社区8| 国产欧美日韩精品亚洲av| 长腿黑丝高跟| 亚洲国产精品成人综合色| 俄罗斯特黄特色一大片| а√天堂www在线а√下载| 男女视频在线观看网站免费| 俺也久久电影网| 麻豆成人午夜福利视频| 老司机午夜十八禁免费视频| 欧美中文日本在线观看视频| 亚洲男人的天堂狠狠| 国产单亲对白刺激| 色视频www国产| 桃色一区二区三区在线观看| 国产麻豆成人av免费视频| 久9热在线精品视频| 丝袜美腿在线中文| 午夜福利免费观看在线| 欧美黑人欧美精品刺激| 欧美午夜高清在线| 精华霜和精华液先用哪个| 午夜影院日韩av| 久久人人精品亚洲av| 人人妻人人澡欧美一区二区| 他把我摸到了高潮在线观看| 国产三级黄色录像| 少妇裸体淫交视频免费看高清| 国模一区二区三区四区视频| 午夜精品久久久久久毛片777| 一级av片app| 国产精品一区二区免费欧美| 国产伦在线观看视频一区| 国产黄片美女视频| 国产高清视频在线播放一区| 成人三级黄色视频| 天堂动漫精品| 搡老妇女老女人老熟妇| 一本一本综合久久| 国产v大片淫在线免费观看| 男女那种视频在线观看| 真人做人爱边吃奶动态| 精品福利观看| 91午夜精品亚洲一区二区三区 | 亚洲 国产 在线| 五月伊人婷婷丁香| 亚洲自偷自拍三级| 性色av乱码一区二区三区2| 性色avwww在线观看| 成年免费大片在线观看| 国产色爽女视频免费观看| 好看av亚洲va欧美ⅴa在| 亚洲国产高清在线一区二区三| 波多野结衣高清无吗| 久久亚洲精品不卡| 亚洲国产欧美人成| 亚洲aⅴ乱码一区二区在线播放| 国产成人av教育| 国产av一区在线观看免费| 亚洲国产精品合色在线| 亚洲自拍偷在线| 亚洲美女视频黄频| 欧美一区二区亚洲| 99精品久久久久人妻精品| 淫妇啪啪啪对白视频| 一级黄色大片毛片| 一区二区三区高清视频在线| 日韩成人在线观看一区二区三区| 高清日韩中文字幕在线| 琪琪午夜伦伦电影理论片6080| 丝袜美腿在线中文| 久久久色成人| 国产精品伦人一区二区| 老师上课跳d突然被开到最大视频 久久午夜综合久久蜜桃 | 国产在线男女| 变态另类成人亚洲欧美熟女| 精品人妻偷拍中文字幕| 久久国产乱子伦精品免费另类| 97超视频在线观看视频| 久久精品影院6| 一区二区三区四区激情视频 | 极品教师在线免费播放| 嫩草影院入口| 亚洲人与动物交配视频| 久久精品国产亚洲av天美| 国产在线男女| 精品不卡国产一区二区三区| 嫩草影视91久久| 久久精品国产清高在天天线| 听说在线观看完整版免费高清| 男女视频在线观看网站免费| 成人性生交大片免费视频hd| 中文字幕免费在线视频6| 天堂av国产一区二区熟女人妻| 日本一本二区三区精品| 真人做人爱边吃奶动态| 中文资源天堂在线| 熟女电影av网| 搡老岳熟女国产| 九色成人免费人妻av| 久久亚洲真实| 少妇人妻精品综合一区二区 | 最后的刺客免费高清国语| 亚洲欧美激情综合另类| 国产 一区 欧美 日韩| 欧美绝顶高潮抽搐喷水| 悠悠久久av| 中文字幕人成人乱码亚洲影| 亚洲,欧美精品.| 亚洲七黄色美女视频| 国产美女午夜福利| 99久久成人亚洲精品观看| 欧美激情国产日韩精品一区| 国产一区二区三区视频了| 一a级毛片在线观看| 亚洲狠狠婷婷综合久久图片| 国产精华一区二区三区| 欧美日韩亚洲国产一区二区在线观看| 丁香六月欧美| 熟女电影av网| 3wmmmm亚洲av在线观看| 亚洲av成人av| 日本 欧美在线| 久久99热6这里只有精品| 国产伦精品一区二区三区四那| 小说图片视频综合网站| 亚洲成人中文字幕在线播放| 女生性感内裤真人,穿戴方法视频| 成人无遮挡网站| 亚洲一区高清亚洲精品| 日韩大尺度精品在线看网址| 黄色一级大片看看| 自拍偷自拍亚洲精品老妇| 99在线人妻在线中文字幕| 久久天躁狠狠躁夜夜2o2o| 亚洲一区高清亚洲精品| 看片在线看免费视频| 99视频精品全部免费 在线| 国产男靠女视频免费网站| 九色成人免费人妻av| 高清毛片免费观看视频网站| 色综合欧美亚洲国产小说| 91在线观看av| 日本免费一区二区三区高清不卡| 免费高清视频大片| or卡值多少钱| 久久久久国内视频| 两人在一起打扑克的视频| 国产高清三级在线| 在线十欧美十亚洲十日本专区| 久久精品91蜜桃| 99国产极品粉嫩在线观看| 亚洲激情在线av| 国产精品女同一区二区软件 | 亚洲无线在线观看| 欧美成人一区二区免费高清观看| 国内精品久久久久久久电影| 国产综合懂色| 天天一区二区日本电影三级| 12—13女人毛片做爰片一| 搡女人真爽免费视频火全软件 | 日韩欧美精品免费久久 | 日韩人妻高清精品专区| 热99在线观看视频| 听说在线观看完整版免费高清| 男人和女人高潮做爰伦理| 窝窝影院91人妻| 国产野战对白在线观看| 亚洲五月天丁香| 成人欧美大片| 1000部很黄的大片| 精品久久久久久久久亚洲 | 亚洲av美国av| av视频在线观看入口| 精品久久久久久成人av| 久久久久国产精品人妻aⅴ院| 成人三级黄色视频| 日本a在线网址| 91麻豆av在线| 老熟妇乱子伦视频在线观看| avwww免费| 日韩av在线大香蕉| 欧洲精品卡2卡3卡4卡5卡区| 国产精品98久久久久久宅男小说| 少妇被粗大猛烈的视频| 91久久精品国产一区二区成人| 亚洲av电影不卡..在线观看| 国产白丝娇喘喷水9色精品| 午夜a级毛片| 久久午夜福利片| 老女人水多毛片| 国产午夜福利久久久久久| 亚洲av成人av| 国产成人av教育| 日日摸夜夜添夜夜添av毛片 | 欧美+亚洲+日韩+国产| 国产精品爽爽va在线观看网站| 久久久久性生活片| 国产成+人综合+亚洲专区| 亚洲精品成人久久久久久| 欧美在线一区亚洲| 黄色丝袜av网址大全| 麻豆成人av在线观看| 国产精品,欧美在线| 日韩亚洲欧美综合| 午夜视频国产福利| 免费看a级黄色片| 成人午夜高清在线视频| 别揉我奶头 嗯啊视频| 国产精品久久久久久久电影| 我的女老师完整版在线观看| 男人和女人高潮做爰伦理| 99国产精品一区二区三区| 亚洲综合色惰| 麻豆成人午夜福利视频| 欧美精品啪啪一区二区三区| 国产免费av片在线观看野外av| 亚洲五月婷婷丁香| 成人欧美大片| 亚洲精品一区av在线观看| 中国美女看黄片| 亚洲av成人精品一区久久| 午夜福利在线在线| 91久久精品国产一区二区成人| 国产 一区 欧美 日韩| 国产爱豆传媒在线观看| 精品免费久久久久久久清纯| 精品午夜福利视频在线观看一区| 伦理电影大哥的女人| www.色视频.com| 天堂网av新在线| 在线观看av片永久免费下载| 嫩草影院精品99| 国产成人欧美在线观看| 亚洲最大成人中文| 草草在线视频免费看| 桃红色精品国产亚洲av| 欧美最黄视频在线播放免费| 久久久久久九九精品二区国产| 亚洲最大成人av| 国产精品久久久久久久久免 | 国产乱人视频| 听说在线观看完整版免费高清| 国产精品伦人一区二区| 久久久久免费精品人妻一区二区| 亚洲国产精品999在线| 男女视频在线观看网站免费| 久久久久精品国产欧美久久久| 亚洲一区二区三区色噜噜| 色综合站精品国产| 很黄的视频免费| 成人国产综合亚洲| 我的女老师完整版在线观看| 99在线视频只有这里精品首页| 色综合婷婷激情| eeuss影院久久| 亚洲欧美清纯卡通| 可以在线观看毛片的网站| 亚洲乱码一区二区免费版| 亚洲aⅴ乱码一区二区在线播放| 中文在线观看免费www的网站| 欧美一区二区精品小视频在线| 露出奶头的视频| 欧美中文日本在线观看视频| 网址你懂的国产日韩在线| 日本精品一区二区三区蜜桃| 可以在线观看的亚洲视频| 内射极品少妇av片p| 久久久久久久久大av| 国产淫片久久久久久久久 | 国产精品综合久久久久久久免费| 中文字幕熟女人妻在线| 精品99又大又爽又粗少妇毛片 | 精品不卡国产一区二区三区| 色哟哟·www| 午夜福利成人在线免费观看| 久久精品91蜜桃| 九色成人免费人妻av| 蜜桃亚洲精品一区二区三区| 午夜两性在线视频| 舔av片在线| 丰满人妻熟妇乱又伦精品不卡| 一区二区三区高清视频在线| 天美传媒精品一区二区| 精品人妻一区二区三区麻豆 | 亚洲av电影在线进入| 亚洲人成网站在线播| av在线蜜桃| 69人妻影院| 最近最新中文字幕大全电影3| 此物有八面人人有两片| 成人午夜高清在线视频| 国产色婷婷99| www日本黄色视频网| 男人和女人高潮做爰伦理| 国产伦在线观看视频一区| 宅男免费午夜| 亚洲人成伊人成综合网2020| 午夜两性在线视频| 女人十人毛片免费观看3o分钟| 国产在线男女| 日韩欧美精品v在线| 亚洲最大成人手机在线| 日韩精品中文字幕看吧| 男女床上黄色一级片免费看| 日本黄色片子视频| 日本黄色视频三级网站网址| 91久久精品国产一区二区成人| 中文字幕人妻熟人妻熟丝袜美| 久久久久亚洲av毛片大全| 男女视频在线观看网站免费| 精品久久久久久久人妻蜜臀av| 久久精品夜夜夜夜夜久久蜜豆| 可以在线观看的亚洲视频| 亚洲色图av天堂| 国产精品爽爽va在线观看网站| www.熟女人妻精品国产| 亚洲精品一区av在线观看| 禁无遮挡网站| 欧美日韩瑟瑟在线播放| 成年女人永久免费观看视频| 国内久久婷婷六月综合欲色啪| av天堂在线播放| www.www免费av| 伦理电影大哥的女人| 淫秽高清视频在线观看| 国产aⅴ精品一区二区三区波| 久久国产乱子免费精品| 午夜精品久久久久久毛片777| 精品福利观看| 亚洲性夜色夜夜综合| 国产高清三级在线| 精品久久久久久久久亚洲 | 国产亚洲精品久久久com| 免费看光身美女| 成人特级av手机在线观看| 久久国产精品人妻蜜桃| www日本黄色视频网| 国产成人aa在线观看| 日韩中文字幕欧美一区二区| 男女之事视频高清在线观看| 日日摸夜夜添夜夜添小说| 色综合亚洲欧美另类图片| 又爽又黄无遮挡网站| 日本免费一区二区三区高清不卡| 午夜福利在线观看吧| 亚洲欧美日韩东京热| 综合色av麻豆| 国内精品久久久久精免费| 久久这里只有精品中国| 美女高潮的动态| 成人av一区二区三区在线看| 97热精品久久久久久| 99国产精品一区二区三区| 丰满乱子伦码专区| 99热这里只有是精品50| 欧美bdsm另类| 欧美丝袜亚洲另类 | 国产精品亚洲一级av第二区| 最近中文字幕高清免费大全6 | 女同久久另类99精品国产91| 国产黄色小视频在线观看| 国产激情偷乱视频一区二区| 丰满的人妻完整版| 国产v大片淫在线免费观看| 神马国产精品三级电影在线观看| 好男人在线观看高清免费视频| 免费无遮挡裸体视频| 在线观看美女被高潮喷水网站 | 999久久久精品免费观看国产| 日本 欧美在线| 国产精品乱码一区二三区的特点| 最近视频中文字幕2019在线8| 99热精品在线国产| 宅男免费午夜| 别揉我奶头 嗯啊视频| 精华霜和精华液先用哪个| 亚洲人成伊人成综合网2020| 一进一出抽搐gif免费好疼| 一本久久中文字幕| 免费av不卡在线播放| av视频在线观看入口| 亚洲国产精品合色在线| 18禁在线播放成人免费| 国产在线男女| 亚洲熟妇熟女久久| 国产在线精品亚洲第一网站| 久久久久久久久大av| www.熟女人妻精品国产| eeuss影院久久| 蜜桃亚洲精品一区二区三区| 人人妻人人澡欧美一区二区| 三级毛片av免费| 久久热精品热| 国产精品美女特级片免费视频播放器| 亚洲成人免费电影在线观看| 免费人成视频x8x8入口观看| 天天一区二区日本电影三级| 免费看美女性在线毛片视频| 赤兔流量卡办理| 亚洲国产欧美人成| 成人欧美大片| 亚洲熟妇熟女久久| 脱女人内裤的视频| 99热只有精品国产| 久久人妻av系列| 亚洲精品色激情综合| 国内久久婷婷六月综合欲色啪| 国内揄拍国产精品人妻在线| 国产精品久久久久久久久免 | 亚州av有码| 一本精品99久久精品77| 久久久成人免费电影| 直男gayav资源| 久久久成人免费电影| 99久久成人亚洲精品观看| 精品一区二区免费观看| 在线播放国产精品三级| 午夜a级毛片| 亚洲美女搞黄在线观看 | 亚洲精品乱码久久久v下载方式| 色噜噜av男人的天堂激情| 婷婷丁香在线五月| 国产三级在线视频| 一级黄片播放器| 国产高清视频在线播放一区| 久久九九热精品免费| 国产精品久久久久久久电影| 69av精品久久久久久| 国产亚洲精品综合一区在线观看| 久久久久久久久大av| 国产成人欧美在线观看| 人妻夜夜爽99麻豆av| 性色avwww在线观看| 少妇熟女aⅴ在线视频| 国产精品自产拍在线观看55亚洲| 天堂影院成人在线观看| www日本黄色视频网| 日韩 亚洲 欧美在线| 永久网站在线| 99久久无色码亚洲精品果冻| 久久精品国产亚洲av涩爱 | 少妇的逼水好多| 日韩欧美一区二区三区在线观看| 国产精品久久久久久久久免 | 亚洲真实伦在线观看| 一级黄片播放器| 午夜两性在线视频| 一个人免费在线观看电影| 99久久精品一区二区三区| 99久久精品热视频| 色av中文字幕| 99国产极品粉嫩在线观看| 久久久国产成人免费| 永久网站在线| 国产成人影院久久av| 伦理电影大哥的女人| 欧美性猛交╳xxx乱大交人| 午夜视频国产福利| 国产黄a三级三级三级人| 国产高清三级在线|