• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Innovation and Practice of Hard Rock TBM in China

    2018-05-10 09:17:58HONGKairongWANGDujuanGUORujun51158500015001661171
    隧道建設(中英文) 2018年4期

    HONG Kairong, WANG Dujuan, GUO Rujun(1. ., ., 51158, , ;2. , 50001, , ;. ., ., 50016, , ;. ., ., 61171, , )

    0 Introduction

    The hard rock tunnel boring machine (TBM) is characterized by high efficiency, good tunnel contour, little impact on surroundings, etc., hence, it is particularly suitable for the construction of deep long tunnels. The method has been successfully applied to the construction of tunnels in the fields of energy, transportation, water conservancy, national defense, etc. in many countries, such as the completed Lesotho South-to-North Water Diversion Project[1], the Channel Tunnel[2]and the Vereina Tunnel[3]. Some manufacturers, such as Robbins (USA), Herrenknecht AG (Germany), and CMC (Italy), have already had relatively complete sets of TBM design, manufacturing and application technologies; while, compared with the relatively well-developed technologies abroad, there is still a way for China′s R&D and engineering application of TBMs to go on[4-5]. For tunneling under complex geological conditions, some TBM manufacturers in China have made valuable exploration in the design of tunneling solutions for weak surrounding rock deformation, fractured fault zone, high ground stress, high rock temperature, rock burst, high-pressure confined water, gushing water, and many other unfavorable geological conditions[6-11], and have made some progresses and bottleneck broken through considering our long duration of dependence on foreign supplies and joint manufacturing.

    China has already been known as the country with the largest tunnel construction scale and the fastest tunnel construction development speed in the world, as well as the county with the highest difficulty in tunnel construction due to the complex geological conditions in mountainous areas. In the next few years, China is going to build a large number of railway tunnels in the central and western regions, and more frequently TBMs will be utilized. At present, TBM is still considered poor design for dealing with unfavorable geological conditions, and has the disadvantages such as passive (or lagging) treatment, slow response, complex manual operations, and delaying construction period. Furthermore, it is difficult to perform advance geological prediction and to adopt assistant construction methods timely and effectively. In case of unexpected unfavorable geological conditions, problems such as jamming are likely to occur, which affects the efficiency of TBM tunneling and may even result in major safety accidents. The conventional TBMs suffer from fixed structure model, and thus the shortcomings such as small space for support operation of TBM main body, mutual interference of various processes, complex material transportation system, and low reliability, seriously restrict the efficiency of TBM tunneling. When TBMs are applied to the construction under complex geological conditions, in order to solve the problems such as high ground temperature, high rock burst, and mud outburst & gushing water, we need to conduct relevant research on how to further increase the material transportation efficiency of TBM and improve the adaptability of TBM to complex strata.

    Based on the complex geological conditions of Gaoligongshan Tunnel on Dali-Ruili Railway, i.e. high ground temperature, high ground stress, and high seismic intensity, as well as active neotectonic movement, active geothermal water environment, active externally-driven geological conditions, and active bank slope surface reconstruction, and the existing equipment performance, the study and manufacturing work of TBM is carried out from the aspects of high efficiency rock breaking, TBM over-excavation design, support system design and advance geological prediction, so as to enhance the TBM integration technology, overcome the technical problem concerning the best matching of design performance and tunneling parameters, and achieve a further leap of TBM.

    1 Analysis of state-of-art of TBM research and application

    1.1 Analysis of stat-of-art of TBM research and application in China and abroad

    1.1.1 TBM research and application abroad

    In 1851, the world′s first TBM that could be used for continuous tunneling was designed by Charles Wilson, an American engineer. However, due to the fact that the rock breaking-related problem was not solved effectively, the construction efficiency of TBM was hardly comparable to that of the drilling-blasting method, which thus left the TBM useless. In 1956, with the help of disc cutter technology, the rock breaking-related problems were successfully solved. Since then, TBMs have been widely promoted and utilized. The statistics of some representative TBM projects abroad are shown in Table 1. At present, foreign TBM technology has been relatively well developed. The main TBM manufacturers include Robbins, Wirth, Herrenknecht AG, Lovat, Komatsu, and so on.

    1.1.2 Research on and application of TBM in China

    China started TBM R&D in 1964, when Shanghai Investigation, Design & Research Institute Co., Ltd. (SIDRI) and Beijing Water Resources and Electric Power College (now North China University of Water Resources and Electric Power-NCWU) jointly conducted the conceptual design. In 1965, the development of TBM was listed as a national key scientific research project. A TBM with a diameter of 3.5 m was developed under the guide of SIDRI, and the corresponding industrial test (with the geological conditions for excavation being granitic gneiss and limestone, and the compressive strength being 100-240 MPa) was conducted at Xierhe Cascade Hydro-power Station Power Tunnel in Xiaguan Town, Yunnan, with a maximum monthly advance rate of 48.5 m.

    Table 1 Foreign typical TBM projects[12-15]

    At the beginning of the 21st century, as one of the major technological equipments in the 16 fields prioritized to revitalize Chinese equipment manufacturing industry, the TBM industry faced unprecedented opportunities for development. China Railway Engineering Equipment Group Co., Ltd. and China Railway Construction Heavy Industry Co., Ltd. were founded at the right moment. Up to now, such companies have had strong capability for the design and manufacturing of TBM. In recent years, some Chinese companies have been relying on the National High-tech R&D Program ("863 Program") and the National Key Basic R&D Program ("973 Program") to carry out the independent research and development of TBM. The statistics of some achievements are shown in Table 2.

    The typical cases of the application of TBM in construction of rock tunnels in China are shown in Table 3.

    Table 2 Typical TBMs developed by Chinese companies [6,16-18]

    Continued Table 2

    Table 3 Typical cases of application of TBM to construction of rock tunnels in China[19-24]

    Continued Table 3

    1.2 Analysis of state-of-art of research on key TBM technologies

    1.2.1 State-of-art of research on TBM adaptability

    In the past 20 years, TBM tunneling technologies have been rapidly developed in China. However, there is no national specification on TBM-based tunnel design and construction yet. In addition, China has a vast area and great differences in engineering geological conditions. Therefore, formulating a set of reasonable design philosophy and construction technology system featuring the good adaptability of TBM to ground characteristics has become a challenge for TBM design and tunnel construction development.

    1.2.2 State-of-art of research on TBM tunneling technologies

    In view of the challenge concerning TBM tunneling technologies under complex geological conditions, relevant organizations in China and abroad have conducted targeted researches and attempts, but there are still some problems to be solved, such as prevention and control of rock burst and gushing water: (1) The prevention and control of rock burst during TBM tunneling are still in the exploratory stage. The rock burst level can only be roughly predicted, and it is difficult to accurately predict the time and location of occurrence of rock burst; with regard to the control of medium or higher-level rock burst, there is a lack of scientific theoretical guidance in respect of the timing and solution selection[25]; for strong or extremely strong rock burst, the resulted damage can only be mitigated through corresponding supporting measures, and it is hard to effectively control such burst; (2) TBM tunneling in water-rich ground is very risky, and it is difficult to effectively deal with such risk; at the same time, there is a risk that TBM may be sunk, submerged, or buried in water-bearing loose ground due to the mud burst or gushing water. The technical measures in respect of geological prediction, advance treatment, drainage, water stopping and so on for tunnel-related water gush mostly originate from experience, that is to say, there is a lack of corresponding theoretical guidance; it is hard to achieve good combination of equipment allocation, technology and TBM, and the implementation effect is not satisfactory.

    1.2.3 State-of-art of research on advance geological prediction

    Methods of advance geological prediction for tunnel construction can be classified into two categories, i. e. geological method and geophysical method[26]. During the drilling-blasting-based tunnel construction, the prediction technology for unfavorable geologic bodies ahead of the working face is relatively proven. Because of the structure and construction method characteristics of TBM, many conventional geological prediction methods cannot be used or are greatly restricted in tunnels constructed by TBM. Therefore, the advance geological prediction system for TBM tunneling still needs further development and improvement.

    1.3 Typical cases of TBM tunneling projects

    1.3.1 TBM tunneling in fractured fault zones and weak surrounding rock sections

    1.3.1.1 Diversion Tunnel of Nabang Hydropower Station in Yunnan

    The excavation diameter of the tunnel is 4.5 m, the length is 9.8 km, and the open TBM manufactured by Herrenknecht AG is used for construction. There the rock is dominated by gneiss, and large faults and gushing water exist. The section is characterized by the alternation of extremely hard rock and weak alteration belt. The construction of this project encounters high cutter wearing, cutterhead weld cracking, plastic deformation of cutter holder positioning surface, jamming caused by surrounding rock deformation in weak alteration belts, gripper failing to support the movement forward, and other technical problems.

    1.3.1.2 Countermeasures and construction result

    In the initial stage of TBM design, an emergency shotcreting system connected to the back-up shotcreting system of the TBM was designed and arranged; by utilizing the delivery pump of the back-up shotcreting system, the concrete was directly transported via the pipeline transferring joints to the front of the TBM main body for concrete casting. During passing through the weak surrounding rock in alteration belts, the distance of about 10 m from the gripper to the shield tail of open TBM was utilized to timely erect steel arches with short intervals and cast early-strength concrete at places where the shield had just emerged. In this way, the TBM successfully passed through six sections of weak surrounding rock in alteration belts with a total length of about 500 m. For weak and deformed surrounding rock, the following technical countermeasures may be considered.

    (1)Appropriate TBM shall be selected. If shielded TBM is used, the diameter of the shield shall be reduced stepwise from the front to the rear, the length of the shield shall be shortened as much as possible, and the thrust capacity shall be enhanced.

    (2)In order to cope with the large deformation of surrounding rock, the TBM over-excavation design shall be considered. In the case of over-excavation diameter ≤ 100 mm, the technical solution of stretching the gauge cutter cushion block outward shall be adopted; in the case of over-excavation diameter > 100 mm, the technical solution of "cutterhead lifting system + reservation of gauge cutter holder + outward-stretching of gauge cutter cushion block "or" replacement of cutterhead gauge cutter block + modification of shield" shall be adopted.

    (3)With respect to the new type of support design and protection design, the flexible water-expansion anchor bolt support, flexible steel arch support, semi-mechanized emergency shotcreting system, and continuously closed "rebar panel supporting system" may be adopted according to the actual conditions.

    1.3.2 TBM tunneling in surrounding rock sections with strong rock burst

    So far, the finished TBM tunneling projects featuring typical rock burst in China include the Qinling Tunnel of Xi′an-Ankang Railway and the Diversion Tunnel of Jinping Ⅱ Hydroelectric Project, etc.; those under construction include the ABH Water-conveyance Tunnel Project in Xinjiang, the Hanjiang River to Weihe River Water Diversion Project in Shaanxi and the Gaoligongshan Tunnel on Dali-Ruili Railway, etc[27-29]. For surrounding rock sections with strong rock burst, the following technical countermeasures may be considered.

    (1)For medium or less-strong rock burst: The equipment of open TBM may be based on to adopt the wiremesh, anchor bolt, steel arch, and shotcreting, or the combined flexible anchor bolt, flexible steel arch, and rebar panel support; as long as proper control is carried out, the influence of rock burst on project construction may be greatly reduced.

    (2)For extremely strong rock burst, due to the difficulty in accurate prediction and control in respect of time and location, at present, the influence of rock burst on project construction could only be reduced as far as possible by utilizing appropriate support techniques, pilot borehole and drilling-blasting-based pretreatment, etc.

    (3)The micro-seismic monitoring technology shall be adopted to predict rock burst; the accumulation and summarization of more practical project experience shall be based on to systematically analyze the interrelationship among the conditions, time, location and impact of rock burst, so as to further improve the rock burst monitoring technology.

    1.3.3 TBM tunneling in sections with mud burst and gushing water

    Mud burst and gushing water have great influence on TBM tunneling. Currently, TBM tunneling projects suffering from severe mud burst and gushing water in China include the Qinling Tunnel of Hanjiang River to Weihe River Water Diversion Project, the Wanjiazhai Yellow River Diversion Project in Shanxi, the Jinping Ⅱ Hydroelectric Project and the Taohe River Water Diversion Project, etc. For sections with mud burst and gushing water, the following technical countermeasures may be considered.

    (1)During tunneling upwards, the risk is generally controllable; according to the specific conditions of the projects, consideration may be given to the gravity drainage of the tunnel or the proper arrangement of drainage system and elevated transportation track.

    (2)During tunneling downwards, the availability of the TBM declines, hence both the cost and the construction period increase, and the equipment may be submerged, that is to say, there is high risk. Therefore, it is recommended to provide super-strong drainage system in advance according to the survey and design data (it is necessary even if no heavy gushing water occur).

    (3)For gushing water from fissures of relatively complete rock mass, the effect of advance grouting may be limited, hence the technical solution, "drainage + water stopping", should be adopted.

    (4)In sections with gushing water from karst cave and weak, fractured and loose rock mass, water and/or mud burst(s) may occur, hence the TBM is very likely to be jammed. In this case, the TBM should pass through step by step after carrying out advance geological prediction and advance grouting or manual treatment.

    (5)Some projects may require the use of dual-mode TBM (i.e., with the open TBM tunneling mode and the EPB (earth pressure balance) shield tunneling mode) for construction, where conversion between the two modes may be conducted according to the geological conditions.

    2 Project overview

    2.1 Overview of tunnel project

    With a total length of 34.5 km, Gaoligongshan Tunnel on Dali-Ruili Railway is currently the first ultra-long single-track railway tunnel under construction in China. The geological conditions of the tunnel are complex. For the exit section of the tunnel, the main tunnel is constructed by large-diameter TBM, while the parallel adit is constructed by small-diameter TBM. The main tunnel is constructed by the largest-diameter TBM developed by Chinese engineers (namely, T "Caiyun", with an excavation diameter of 9.03 m), and the TBM tunneling began on January 6th, 2018; the parallel adit is constructed by the first re-manufactured TBM in China (namely, the TBM "Caiyun Ⅰ", with an excavation diameter of 6.39 m), and the TBM tunneling began on August 28th, 2017. The plan layout for construction of Gaoligongshan Tunnel is shown in Fig. 1.

    2.2 Geological characteristics of tunnel sections constructed by TBM

    In the exit section of Gaoligongshan Tunnel to be constructed by TBM, the ground surface is sporadically covered by the Quaternary Holocene landslide accumulation, colluvium and deluvium, alluvium and proluvium, deluvium and proluvium, deluvium, deluvium and eluvium, as well as the Upper Pleistocene alluvial-proluvial mollisol, silty clay, coarse sand, gravelly sand, fine-round (angular) gravel soil, coarse-round (angular) gravel soil, gravelly soil, cobbly soil, boulder soil, block stone soil, and other strata. The underlying ground include the Neogene and Yanshanian granite, unknown mixed granite, dolerite dyke, as well as fault angular gravel, crushed rock, and alterated rock of crushed fracture and fault zones of various periods, etc. The ground passed through by TBM tunneling are mainly composed of Yanshanian granite (8.81 km, 73%), schist, slate, phyllite mixed with quartzite, and metamorphic sandstone (1.44 km, 22%). The surrounding rock is mainly of Grade Ⅲ, but the proportion of Grade Ⅳ and Grade Ⅴ surrounding rock is as high as 40%. It is predicted that the normal volume of gushing water in the main tunnel is 12.77×104m3/d and the maximum volume is 19.2×104m3/d. The main parameters of surrounding rock of the tunnel sections constructed by TBM are shown in Table 4.

    Table 4 Main parameters of surrounding rocks of tunnel sections constructed by TBM

    2.3 Analysis of unfavorable geological conditions

    The unfavorable geological conditions of TBM tunneling section of Gaoligongshan Tunnel mainly include high ground stress, fractured ground, high ground temperature, high seismic intensity, dissolvable rock and water gush, etc.

    (1)High ground stress: The maximum cover of the tunnel is 1 155 m, and the regional stress field is relatively high. The relationship among the values of three-dimension principal stress around the tunnel body in the survey area is: vertical principal stress (about 31 MPa) > maximum horizontal principal stress (20-29 MPa) > minimum horizontal principal stress (13-19 MPa). The angle between the dominant direction of the maximum horizontal principal stress and the direction of the tunnel alignment is 12°-21°, and rock burst and large deformation of soft rock may occur to the tunnel. According to the prediction, the total length of soft rock large-deformation section of the main tunnel is 3 185 m, and the length of slight large-deformation section is 1 435 m; in fractured fault zones, local fault clay is prone to medium-large deformation, with a length of 1 750 m.

    (2)Fractured ground: There will be 20 fractured-extremely fractured rock mass sections (with a total length of 1 280 m) in TBM tunneling section of main tunnel; there will be 15 fractured-extremely fractured rock mass sections (with a total length of 980 m) in TBM tunneling section of parallel adit. The proportion of Grade Ⅳ and Grade Ⅴ surrounding rock passed through by the whole tunnel is as high as 40%.

    (3)High ground temperature: In mountain-crossing sections of Gaoligongshan Tunnel, the maximum temperature measured by deep hole drilling is 40.6 °C, the maximum temperature at the shoulder surface is 36.7 °C, and the temperature of the rock mass in tunnel body section D1K197+460~D1K207+582 (with a length of 10.122 km) is 28~39 °C[30].

    (4)High seismic intensity: The area is located in the seismic zone of southwestern Yunnan, where the intensity of seismic activity is very high and the earthquake frequency is high. The seismic ground motion peak acceleration in the survey area is 0.20g, and the period of seismic ground motion response spectrum is 0.45 s. The correlation between the strong earthquakes and the distribution of the active faults is extremely high, and most of the strong earthquakes above Magnitude 6 are distributed along active faults. The site ever suffered strong earthquakes in the history. In May 1976, a 7.3-magnitude earthquake occurred in Longling.

    (5)Dissolvable rock and water gush: In the entrance section of the tunnel, the total length of the Triassic dolomite and the sandwich-type dissolvable rock in Jurassic, Ordovician, Cambrian and other strata is 1 392 m, with the karst weakly-moderately developed. The Silurian limestone and dolomite in the middle of the tunnel are 590 m in length, and the Devonian limestone and dolomite in the exit section of the tunnel are 1 330 m in length, with the karst weakly developed.

    3 Research on adaptability of key TBM parameters

    3.1 Research on adaptability of rock-breaking and wearing parameters of TBM disc cutters

    3.1.1 Research on adaptability of rock breaking of disc cutters

    The arrangement of TBM cutters, especially the spacing between the cutters, is crucial to the rock breaking efficiency of TBM. A reasonable spacing between cutters has an important influence on the improvement of tunneling ability of TBM. Therefore, it is necessary to carry out the prototype disc cutter rock breaking experiment under different cutter spacing, to determine the reasonable cutter spacing with respect to the arrangement of TBM cutters, so as to provide reference for the design of TBM cutterhead.

    3.1.1.1 Scheme of experiment on different cutter edge spacings

    By using the TBM boring mode experimental platform (as shown in Fig. 2), the edge spacing of the disc cutters on the cutterhead was adjusted to 80 mm, 90 mm, 100 mm, 110 mm, 120 mm and 130 mm, respectively, and disc cutter rock breaking tests were carried out under 6 different cutter edge spacings.

    Fig. 2 TBM boring mode experimental platform

    The rock sample used was granite. The rock sample was in the form as shown in Fig. 3. Four pieces (two pieces of each type) were processed and spliced respectively, with gaps in the middle filled with concrete. The rock used was granite with a strength of 180-190 MPa.

    (a)

    (b)Fig. 3 Forms of rock samples (unit: mm)

    3.1.1.2 Experimental phenomena and result analysis

    (1)Analysis on effect of rock breaking by disc cutter under different cutter edge spacings

    The actual effect of rock breaking by disc cutter under different cutter edge spacings is shown in Fig. 4.

    (a) Cutter edge spacing of 80 mm (b) Cutter edge spacing of 90 mm

    (c) Cutter edge spacing of 100 mm (d) Cutter edge spacing of 110 mm

    (e) Cutter edge spacing of 120 mm (f) Cutter edge spacing of 130 mm

    Fig. 4 Effect of rock breaking by disc cutter under different cutter edge spacings

    From Fig. 4, it can be seen that when the cutter edge spacing is 80 mm, 90 mm, 100 mm or 110 mm, the rock can be effectively broken, and there is no phacolith on the surface of rock sample; when the cutter edge spacing is 120 mm or 130 mm, unfallen rock locally exists within the cutter edge spacing on the surface of rock sample, but as the tunneling continues and the depth of penetration increases, such remaining rock can also fall.

    The muck produced in experimental groups with different cutter edge spacings was screened and classified, with the results shown in Fig. 5.

    Fig. 5 Screen results of muck produced under different cutter edge spacings

    According to Fig. 5, under different cutter edge spacings, the proportion of each muck size is slightly different, but the overall distribution is similar. The proportion of rock blocks with a size of 40-50 mm and that of rock powder with a size of less than 2.5 mm account for 11%-16% and 18%-25% respectively.

    (2)Analysis on specific energy of rock breaking under different cutter edge spacings

    By keeping the tunneling speed and the rotating speed of cutterhead steady, the specific energy of rock breaking under different cutter edge spacings was analyzed, with the relationship between the disc cutter edge spacing, penetration and the specific energy shown in Fig. 6.

    Fig. 6 Statistical relationship between S/p and specific energy

    According to Fig. 6, for the granite, when the ratio of the cutter edge spacing to the penetration (S/p) is 25-30, the specific energy is the lowest (about 35 000-40 000 kJ/m3); when the cutter edge spacing is 80 mm, the best penetration is 2.7-3.2 mm/r; when the cutter edge spacing is 120 mm, the best penetration is 4-4.8 mm/r. From the viewpoint of specific energy only, the cutter edge spacing of 120 mm is relatively reasonable; however, the TBM tunneling of the project will encounter high-strength rock, and the actual average penetration of TBM is small. Therefore, 80 mm is adopted as the edge spacing of the front disc cutter spacing of the cutterhead, which is beneficial to the rock breaking by disc cutter; the cutter edge spacing of 90 mm or 100 mm is adopted for central disc cutter because of the small rock-breaking amount.

    3.1.2 Research on adaptability of disc cutter wearing

    The wearing of TBM cutters is influenced by the geological, mechanical and other factors. In order to understand the law of influence of such factors on disc cutter wearing, indoor wearing tests with the help of scaled disc cutter (small disc cutter) were performed (because the indoor cutter wearing amount of prototype disc cutter is relatively small, so it is difficult to obtain relevant data). The experimental apparatus is shown in Fig. 7.

    Fig. 7 Device for scaled disc cutter wearing test

    3.1.2.1 Scaled disc cutter wearing test under different lithology

    In order to explore the law of influence of rock abrasiveness on disc cutter wearing, scaled disc cutter wearing tests and rock abrasiveness tests were carried out for 5 kinds of rocks, i.e. granite, sandstone, diorite, limestone and marble.

    (1)Scheme of scaled disc cutter wearing test under different lithology

    The flat-edge disc cutter with a diameter of 1.7 inches and an edge width of 1.9 mm was adopted as the small disc cutter. The penetration speed of disc cutter was set to 0.05 mm/stroke; the stroke per attempt of cutting was 250 mm; after every 100 m was rolled by the disc cutter, the mass loss was weighed once, and the average value of the results of 3 times of weighing was calculated. The rock abrasiveness servo system was used to test the CAI of 5 kinds of rocks.

    (2)Analysis on experiment results

    The results of scaled disc cutter wearing tests and rock abrasiveness tests for 5 kinds of rock samples are as shown in Table 5.

    Table 5 Statistics of disc cutter wearing and CAI

    By fitting the relationship between disc cutter wearing and CAI, the relationship between small disc cutter wearing per 100 m and CAI is:w= 0.784 5×CAI2, as shown in Fig. 8.

    Fig. 8 Relationship between disc cutter wearing and CAI

    From Fig. 8, the rate of disc cutter wearing is not only related to the compressive strength of rock, but also has a certain positive correlation with the rock abrasiveness indicator (CAI). In addition, although the compressive strength of diorite, limestone and marble was relatively high, it was observed during the experiment that the rock breaking efficiency of disc cutter was high, and the rock chips all dropped in large pieces, that is to say, the rock was brittle and the disc cutter wearing was relatively small.

    3.1.2.2 Scaled disc cutter wearing test under different penetrations

    (1)Scheme of scaled disc cutter wearing test under different penetrations

    The flat-edge disc cutter with a diameter of 1.7 inches and an edge width of 1.7 mm was adopted as the small disc cutter. The penetration speed of disc cutter was set to 0.08 mm/stroke, 0.07 mm/stroke, 0.05 mm/stroke and 0.03 mm/stroke respectively; the stroke per attempt of cutting was 250 mm; after every 100 m (namely, 400 strokes) was rolled by the disc cutter, the mass loss was weighed once, and the average value of the results of 3 times of weighing was calculated. Such tests were carried out for gray granite (72 MPa, CAI of 3.5) and red granite (98 MPa, CAI of 3.8).

    (2)Analysis on experiment results

    Under 4 different penetration rates, the wearing loss per 100 m for gray granite and that for red granite are shown in Table 6.

    Table 6 Disc cutter wearings under different penetrations

    The relationships between disc cutter wearing per 100 m and penetration of the two kinds of granite are shown in Fig. 9.

    Fig. 9 Relationships between disc cutter wearing and penetration

    From the above analysis, we can see that the abrasiveness of the selected red granite is significantly higher than that of the selected gray granite; with the increase of penetration, the wearing-induced mass loss of the disc cutter increases linearly. When the penetration reaches a certain value, the wearing-induced mass loss of the disc cutter increases sharply, mainly due to the large vertical force acting on the disc cutter under large penetration and thus the crimping of disc cutter edge caused. The edge material after crimping is more likely to fall off, which results in the sharp increase of the wearing-induced mass loss of the disc cutter. Therefore, it is recommended that during field TBM tunneling, the thrust should be controlled in such a way that no crimping of disc cutter edge occurs, which will help to control the disc cutter wearing.

    3.1.2.3 Scaled disc cutter wearing test under different disc cutter types

    (1)Different edge widths

    The 1.9-inch disc cutters with edge widths of 1.9 mm, 1.6 mm, and 1.3 mm respectively were used, to carry out the disc cutter wearing tests under the condition that other experimental parameters are the same. The size of disc cutter for tests was reduced by 1∶10, with the material and process being the same as those of prototype disc cutter; the wearing-induced mass loss of small disc cutter was weighed via a balance (with a precision of 0.001 g). The experiment results are shown in Table 7.

    Table 7 Disc cutter wearings with different edge widths

    According to the above result analysis, it can be known that the wearing-induced mass loss of disc cutters with different edge widths is basically proportional to the edge width, and thus it can be inferred that the radial wearing of disc cutter is seldom related to the edge width; from the viewpoint of experimental load, the load on the disc cutter does not decrease significantly even if the edge becomes narrow (the wearing-induced mass loss is proportional to the wearing-induced volume loss, and the wearing-induced volume loss is the product of edge width, perimeter and radial wearing; the wearing-induced mass loss is basically proportional to the edge width, and thus it can be inferred that the radial wearing is basically the same); from the viewpoint of the breaking of the rock sample, the penetration ability increases after the edge becomes narrow, but the cutting-through ability between two indentations weakens.

    (2)Different disc cutter diameters

    Small disc cutters with a diameter of 1.7 inches, 1.9 inches and 2.0 inches respectively were used in the tests, with the material and process being the same as those of prototype disc cutter. The disc cutter wearing tests were performed at a penetration speed of 0.05 mm/stroke. The experiment results are shown in Table 8.

    Table 8 Disc cutter wearings with different disc cutter diameters

    From the analysis on the data in Table 8, it can be seen that when the diameter of the small disc cutter is changed, the wearing per 100 m of the disc cutter does not change significantly; hence it can be seen that there is no direct relationship between the wearing rate of the disc cutter and the diameter of the disc cutter. Meanwhile, the wearing per 100 m of the 1.7-inch-disc cutter increases step by step are mainly due to the significant crimping of the edge during the experiment. Therefore, large-diameter disc cutters are recommended as much as possible in the case of high-strength hard rock, and the service time of disc cutters can be extended by increasing the allowable wearing of the disc cutter.

    (3)Different edge shapes

    The rounded-edge disc cutter (1 mm in fillet) and flat-edge disc cutter with a diameter of 1.9 inches and an edge width of 1.9 mm were used for disc cutter wearing tests. The experiment results are shown in Table 9.

    Table 9 Disc cutter wearings with different edge shapes

    From the above experimental phenomenon, crimping appears on the worn-out flat-edge disc cutter, while no crimping appears on the worn-out rounded-edge disc cutter. From the viewpoint of wearing-induced mass loss, the wearing loss per 100 m of the rounded edge is significantly lower than that of the flat edge. Therefore, rounded-edge disc cutters are recommended in the case of high-strength hard rock.

    3.2 Key parameters of TBM

    The calculated value of each parameter of the TBM for Gaoligongshan Tunnel was obtained according to the known design parameters of the TBM and the calculation method for key parameters of open TBMs; the design value of each parameter of the TBM for Gaoligongshan Tunnel was determined according to the calculated value and some special requirements, as shown in Table 10.

    The key design parameters of the TBM are as shown in Table 11.

    Table 10 Calculation parameters and design value for TBM of Gaoligongshan Tunnel

    Table 11 Main design parameters of TBM of Gaoligongshan Tunnel

    Item ParametersExcavationdiameterofcutterhead/mm9030Centerdouble?edgedisccutter/Nr.4(17inches)Frontsingle?edgedisccutter/Nr.42(19inches)Gaugesingle?edgedisccutter/Nr.12(19inches)Edgespacing/mm89/84/80/75Maximumthrust/kN27490@35MPaThrustcylinder/mm500/320-190Maximumgrippingforce/kN70370@350MPaGrippercylinder/mm810/640-660Maximumgrippingpressure/MPa4.18Ratedtorque/(kN·m)11797@3.4r/minDrivingpower/kW350×12

    4 Research on design scheme of TBM

    4.1 Design of efficient rock breaking of cutterhead and cutters

    Due to the properties of rocks such as medium strength, good integrity and high quartz content, it is necessary to strengthen the rock breaking and protection measures for the cutterhead. The design concept is: completing the excavation and tunneling of the project without large-scale cutterhead repairing. According to the project overview and geological data, the overall design scheme of the cutterhead is: excavation diameter of 9.03 m, cutterhead material of Q345D, total weight of cutterhead of about 200 t, and cutterhead consisting of 5 blocks, as shown in Fig. 10.

    Fig. 10 Design pregram of cutterhead

    4.1.1 Design of high strength of cutterhead

    The center block and outer blocks of the cutterhead are made of forged plates with 270 mm thickness so as to reduce welds, increase the rigidity and strength of the cutterhead and improve the fatigue life of the cutterhead. The flange is made of forgings 300 mm thick, with high strength and good rigidity, to ensure the uniform stress and service life of the main bearing. The cutter saddle is made of the Q345D forgings, and is provided with irregular supporting plates on its back to increase the rigidity and strength of the cutter saddle and to ensure a long service life.

    4.1.2 Small disc cutter spacing

    The cutterhead is provided with 62 disc cutters in total. The edge spacing of the center cutters is 89 mm and that of the front cutters is 80 mm. As a result, a high rock breaking capacity can be achieved, the cutterhead vibration can be effectively reduced, and the service life of the cutters can be improved.

    4.1.3 Nonlinear layout of cutters

    The nonlinear layout of the cutters is helpful to ensure the uniform stress of the cutterhead, avoid large concentrated stress and extend service life of the cutterhead. Under the condition of the same rock strength, the nonlinear layout of the cutters can achieve small vibration and reduce the wearing of the cutters.

    4.1.4 Multiple muck inlets of cutterhead

    The cutterhead is provided with 12 muck inlets to provide enough space for mucks, ensure the thorough scraping of mucks and reduce the secondary wearing of the cutters. The scraper and the scraper holder are connected with high-strength bolts (back-mounted) to facilitate removal and replacement. Various muck guide plates are provided for muck inlets to improve the scraping efficiency and reduce the scraper wearing.

    4.2 Over-excavation design of TBM

    4.2.1 Diameter expansion of cutterhead

    The TBM has two kinds of diameter expansions (i.e. 50 mm and 100 mm). The specific analysis is as follows: (1) In the case of 50 mm diameter expansion, gauge cutters #57-#62, CW1 and CW2 under the L-shaped block are provided with additional gaskets to increase their height (Fig. 11). (2) In the case of 100 mm expansion in the radial direction of the cutterhead, gauge cutters #56-#62, CW1 and CW2 shall be adjusted, while the other cutters are not adjusted. (3) The cutters #56, #57 and #58 shall be provided with additional gaskets to increase their height, and they shall be reassembled after the L-shaped blocks are removed for cleaning of surfaces of cutter saddles and L-shaped pieces. (4) For cutters #59, #60, #61, #62, CW1 and CW2, L-shaped block shall be replaced to increase their height. (5) The 20-inch cutters indicated in Fig. 11 are those composed of 19-inch cutter bodies and 20-inch cutter rings; however, CW2 is the 20-inch cutter with 40 mm eccentricity.

    (a) Over-excavation sketch (b) Cushion on bottom of L-shaped block

    Fig. 11 Design scheme of over-excavation by 50 mm on one side (unit: mm)

    4.2.2 Drive lifting

    In order to realize continuous long-distance over-excavation of TBM, in addition to the changing of the cutterhead diameter, the drive of the TBM shall be lifted so as to prevent gaps between the bottom shield and the surrounding rocks resulted from the enlarging of the cutterhead diameter. The bottom shield of the TBM is rigidly connected to the headstock with bolts. If over-excavation is needed, the connection bolts between the bottom shield and the headstock shall be removed after local over-excavation; and then, lifting cylinders shall be used to lift the headstock to a certain extent, so as to install steel plates with the corresponding thickness between the headstock and the bottom shield; finally, the headstock shall be rigidly connected to the bottom shield again.

    4.3 Design of hidden advance drill

    The structure of the advance drill is shown in Fig. 12. The advance drill, thrust beam and ring gear beam were designed separately in the lower part of the main beam platform. The advance drill shares the same pump station with the anchor drill system in Zone L1.

    Fig. 12 Design program diagram of hidden advanced drill

    In terms of normal tunneling, the advance drill is hidden in the lower part of the main beam platform along with one section of ring gear beam and two sections of ring gear beams fixed on both sides. If advance drilling is needed, the cylinders on both sides shall be used to lift the advance drill and the ring gear beam simultaneously to make the ring gear beam be connected with the gear beams on both sides so that an entire gear ring can be formed. The advance drill can travel around the gear beam at a certain external angle for drilling holes for advance anchor bolts, advance small pipes and advance pipe roofs and facilitating advance grouting equipment for advance support of surrounding rocks ahead of the cutterhead.

    4.4 Design of integrated supporting system

    The TBM is provided with the rebar panel supporting system, wiremesh storage system, steel arch assembling machine, anchor drill, emergency shotcreting system in Zone L1 and shotcreting system in Zone L2, and the rebar panel supporting range is expanded to 250°. The design scheme of the integrated supporting system is shown in Fig. 13.

    Fig. 13 Design scheme of integrated supporting system

    In case of TMB passing through ground with unfavorable geological conditions, in order to reduce collapse and convergence after the surrounding rocks being exposed out of the shield, wet shotcreting manipulators shall be arranged in the main body section of the TBM to seal the surrounding rocks timely. Through the optimization of the structure and space of the TBM, arc tracks and racks shall be added to the steel arch gripping mechanism. In terms of the design of the rack, the track being contaminated and covered by rebound materials of shotcrete shall be taken into account to prevent the trolley being blocked and to protect the track. The gear is meshed with the rack to make the wet shotcreting trolley travel along the arc track. The nozzle for wet shotcreting is mounted on the wet shotcreting trolley and the distance between the wall of the tunnel and the nozzle can be adjusted.

    In terms of feeding of wet shotcreting in Zone L1, the relay mode is adopted for concrete pumping. The wet shotcrete is conveyed to the two concrete pumps on the right of the equipment bridge via the shotcreting pump in Zone L2, and then is pumped to the nozzle for wet shotcreting in Zone L1 via those concrete pumps on the right of the equipment bridge.

    4.5 Design of cooling system

    Forced cooling system is installed on the TBM to reduce the temperature in the working area. Ice transported to the working area from outside the tunnel may also be used for cooling. In the design of the TBM cooling system, the heat generated by TBM equipment, rock walls and mucks shall be taken into account. The ventilation and cooling units will take away most of the heat. The calculation and analysis for type selection of key components of the cooling system are as follows.

    (1)Analysis on type selection of cooling units

    Model: cooling unit RTHE200, three units are installed in total, and space for installation of one unit is reserved;

    Cooling capacity: 3 × 715 kW=2 145 kW;

    Input power: 3 × 149.2 kW=447.6 kW;

    Inlet water temperature: 25 °C;

    Outlet water temperature: 35 °C;

    Total inlet flow: 3×73.84 m3/h =221.52 m3/h.

    (2)Type selection and calculation of air coolers

    Elevation of air inlet entrance of tunnel: 1 250 m;

    Air density: 0.99 kg/m3;

    Air cooler power (when reducing the working area temperature to 28 °C): 3×714.8 kW=2 144.4 kW.

    5 Research on advance geological prediction technology of TBM

    5.1 Advance geological prediction technology with HSP method

    5.1.1 Concept of advance geological prediction technology with HSP method

    Based on the comparative analysis on the geological prediction results and field tests as well as previous research, the geological adaptability of TBM and shields and the development and technical parameters of supporting data acquisition equipment for advance geological prediction were researched. The development of advance geological prediction equipment with HSP method was carried out according to the characteristics of TBM to achieve a small geological prediction equipment, which can be integrated with TBM to perform the geological prediction. The advantages of the geological prediction technology are as follows: (1) The "passive source" is used as the excitation source, so that the drilling, blasting or hammering is not required. (2) Shutdown or extra cooperation from the construction team is not required so that the geological prediction has no impact on the construction. (3) The field test lasts for a short period (about 20 min) and the operation is convenient. (4) The prediction results are displayed in the form of 2D slices or 3D diagrams, and the results are intuitive and vivid.

    5.1.2 Development of advance geological prediction system with HSP method

    The dimensions of HSP NC system is 250 mm×250 mm×73.5 mm. The system is placed in the reserved space of the TBM for advance geological prediction. The receiver detector is installed based on the fast adhesion layout. The wireless transmission module includes a receiving module and a transmitting module. The receiving module is placed on the top of the main control cabin for receiving wireless data and transmitting them to the HSP NC system. The transmitting module is connected with the detector to receive the vibration signal and transmit the signal wirelessly. Real-time prediction data processing software was developed based on the HSP method. Real-time data acquisition and device parameter setting interfaces are shown in Fig. 14.

    5.2 Advance prediction technology with RTP method

    5.2.1 Prediction principle and instrument system

    The ground temperature field consists of the temperature-variable zone, temperature-constant zone and temperature-increasing zone. Most tunnels are constructed in temperature-increasing zones. According to the gradient theory of the ground temperature, the temperature field in the temperature-increasing zones can be obtained via calculation. Subject to the dynamic change, the groundwater continuously exchanges heat with the rock mass, and thus, the distribution of the temperature field will be changed, resulting in distortion. In terms of the RTP method, scientific prediction is achieved through predicting the condition of the groundwater during the construction of the tunnel based on the distortion principle of the temperature field within the excavation range of the tunnel as well as the location and range of the temperature field distortion, so as to prevent groundwater disasters during the construction of the tunnel (Fig. 15).

    Fig. 14 Interface for data acquisition and device parameters

    (a) Theoretical temperature field (b) Distorted temperature fieldFig. 15 Prediction principle of RTP method

    The independently-developed geological prediction apparatus with RTP MSASW instrument was adopted, and dedicated portable sensor installing system is equipped. This instrument is provided with the internal power supply to power the sensors.

    5.2.2 Field data acquisition and data processing & analysis

    Before test, a suitable location in the tunnel was selected to conduct the best drilling test to obtain the depth data of the surrounding rocks of the stable temperature field. In the surrounding areas behind the excavation face of the tunnel (left sidewall, crown and right sidewall), a row of boreholes with fixed depth was uniformly drilled along the tunnel axis according to certain rules, and sensors were placed at the bottom of the borehole before the boreholes were filled with mortar and sealed (Fig. 16). After 12 hours of stabilization, the sensor data was obtained with a thermometric instrument.

    Fig. 16 System layout on site

    The data processing system mainly includes:

    (1)Data preprocessing: input the corresponding parameters (coordinates, kilometerage and elevation) for each measurement point.

    (2)Terrain correction: the result of rock mass temperature test is influenced by the terrain and it is difficult to evaluate the result. Through the terrain correction, the influence of the groundwater on the temperature field of rock mass can be highlighted.

    (3)Gridding and regression analysis: the finite element calculation of the profile formed by the entire survey line can be conducted through gridding, so that the temperature field of rock mass in the whole region can be obtained. The regression analysis aims to establish a functional relationship for the survey line. The resulted characteristic curve can be used to calculate the groundwater location ahead of the working face of the tunnel.

    (4)Automatic mapping and output: the output of results mainly includes the characteristic curve of the temperature field of rock mass and the 2D contour map of the temperature field of rock mass.

    6 Conclusions and suggestions

    Prototype disc cutter rock breaking experiment and scaled disc cutter wearing experiment were carried out based on the complex geological conditions of Gaoligongshan Tunnel on Dali-Ruili Railway such as high ground temperature, high ground stress and high seismic intensity, as well as active neotectonic movement, active geothermal water environment, active externally-driven geological conditions and active bank slope surface reconstruction, and the design scheme of the TBM with highly adaptability to the project was proposed. Based on the research, breakthroughs have been made in key technology fields such as excavation by TBM in weak sections with large deformation and coping with environment with high ground temperature, and the TBM which can be adapted to the complex geological conditions was developed and applied to Gaoligongshan Tunnel on Dali-Ruili Railway. In order to improve the adaptability of the TBM to different geological conditions, related research will be further carried out in later stages in the following aspects according to the construction conditions of Gaoligongshan Tunnel:

    (1)Research on adaptability of key TBM parameters to different grounds: based on the principle of rock-machine interaction, the key elements of adaptability design for the TBM cutterhead and thrust system will be researched. In the aspect of cutterhead design, the theory and method for adaptability design of TBM rock breaking will be established. Based on the geological and hydrological conditions of the project, the key TBM parameters will be calculated with the help of the rock-machine interaction model.

    (2)Research on key technologies for excavation of weak and variable cross-section tunnels with large deformation by TBM: for the long-distance weak surrounding rocks of the project, in order to prevent the tunnel convergence caused by the large deformation of weak surrounding rocks, the requirements of long-distance over-expansion and tunneling shall be taken into account in the process of determining the excavation diameter of the TBM, and the excavation and support structures shall be innovated. Numerical simulation will be conducted based on the motion theory, strength theory and rigidity theory of the mechanisms for mechanical design to analyze the action, rigidity and strength of key mechanisms such as cutterheads and shields and to obtain the mechanism and structure forms applicable to key components for full-face excavation of tunnels with variable cross-sections, so as to guide the design of key components and systems for variable cross-section excavation and supporting by TBM.

    (3)Research on key technologies for prevention and control of high ground stress and rockburst: due to the high ground stress, frequent rockbursts occur to the ground. The project is located in the ground with high cover and high ground stress and the risks of rockburst are extremely high. Rockburst prediction methods will be studied based on comparison of advantages and disadvantages of microseismic movement and acoustic emission. In addition, methods and measures for prevention and control of rockbursts will be proposed through the space-time analysis on high ground stress and rockburst.

    (4)Research on key technologies for adaptability of fast tunneling by TBM in fractured ground: in view of the problems such as low TBM tunneling efficiency and large construction risks in weak and fractured ground, as well as TBM jamming (cutterheads and shields being jammed) and collapse, based on the stability characteristics of rocks and disturbance, the numerical analysis method will be adopted to analyze the space-time evolution of rock properties and to propose measures against jamming of TBM shields and methods for fast supporting, so as to provide theoretical support for the design of TBM shields and fast supporting devices.

    (5)Research on key technologies for TBM tunneling environment protection in ground with high ground temperature: high ground temperature may be encountered in the TBM tunneling section; according to the design data of the project, with the ground temperature redundancy taken into account, theoretical analysis on the equipment heat exchange and the tunnel ventilation will be carried out in respect of such aspects as equipment operating temperature and ambient temperature of the working area, so as to provide prevention and control measures and theoretical basis for TBM tunneling environment protection systems in ground with high ground temperature.

    (6)Research on key technologies for preventing water inrush during tunnel construction by TBM: according to the construction characteristics of the tunnel with deep overburden, the complex engineering geological conditions and hydrogeological conditions of the project shall be analyzed. Water-rich sections shall be selected to analyze the maximum amount of water inrush by the seepage field analysis method. Based on the water inrush pressure and the flow characteristics, the feasibility of measures for advance grouting to improve the geological conditions and seal the water will be analyzed to propose technology measures for advance grouting and to guide the adaptability design of TBM in water inrush ground, as well as to guide the type selection and design of TBM drainage devices according to the principle of limit point for water inrush and to put forward requirements on the waterproof design of the mechanical, electrical and hydraulic devices.

    Acknowledgement

    The study was supported by Research and Development Plan Project of China Railway Corporation (2016G004-A).

    [1]YANG Cihua. WT project report: Lesotho [J]. Tunnel Translation, 1994(3): 22.

    [2] WU Zhiming. Imaging the Taiwan Strait Tunnel inspired by the Channel Tunnel[J]. Railway Knowledge, 2005(2): 42.

    [3] XIAO Shu′an,SATTEL G. Geological advance prediction measurement in Swiss Vereina tunnel project [J]. Guangdong Highway Communications, 1998(S1): 115.

    [4] WILLIS D. The development of TBM [J]. Translator: CHENG Fangquan. Express of Water Resources & Hydropower Information, 2013(11): 24.

    [5] WANG Mengshu. Tunneling by TBM/shield in China: State-of-art, problems and proposals [J]. Tunnel Construction, 2014, 24(3): 179.

    [6]ZHAI Lianghao,WU Jinghua. The application of TBM to introduction of the Songhua River water supply project in Jilin central cities [J]. Journal of Changchun Institute of Technology (Natural Science Edition), 2016, 17(1): 71.

    [7] WU Shiyong, WANG Ge, XU Jinsong, et al. Research on TBM type-selection and key construction technology for Jinping Ⅱ Hydropower Station [J]. Chinese Journal of Rock Mechanics and Engineering, 2008, 27(10): 2000.

    [8] SU Lijun. Theory and technology of stability control of surrounding rock of deep buried soft rock tunnel construction[D]. Wuhan: Wuhan University, 2010.

    [9]CHEN Bingrui, FENG Xiating, ZENG Xionghui, et al. Real-time microseismic monitoring and its characteristic analysis during TBM tunneling in deep-buried tunnel [J]. Chinese Journal of Rock Mechanics and Engineering, 2011, 30(2): 275.

    [10] SUN Zhenchuan, CHEN Jianli. Construction technologies for open TBM used in karst areas and soft-weak and broken grounds: Case study of Songhua River Water Diversion project [J]. Tunnel Construction, 2017, 37(2): 215.

    [11] QIAN Qihu. Main developments and directions of geological prediction and informatized technology of tunnel construction [J]. Tunnel Construction, 2017, 37(3): 251.

    [12] CHEN Bin, LIU Jishan. The application of TBM technique in contemporary rock tunnel engineering [C]// Proceedings of the Shanghai International Tunnel Engineering Symposium, 2005. Shanghai: Shanghai Society of Civil Engineering, 2005: 281.

    [13] JU Qifeng, XIE Xinsheng. Georgia Kaduli hydroelectric project power tunnel construction scheme & construction organization optimization [J]. Design of Hydroelectric Power Station, 2004, 20(3): 30.

    [14] HE Chuan. Challenges and prospectives of construction of long-distance inclined shafts of coal mines by shield/TBM [J]. Tunnel Construction, 2014, 34(4): 287.

    [15] ZHAI Jinying. State-of-art and prospects of TBM tunnel construction[J]. Tunnel Construction, 2002, 22(4): 60.

    [16] ZHU Hong, ZHU Xiaohong. Recent developments in hydropower development in several Asian countries [J]. Express of Water Resources & Hydropower Information, 2014, 35(9): 16.

    [17] JING Liujie, ZHANG Na, YANG Chen. Development of TBM and its construction technologies in China [J]. Tunnel Construction, 2016, 36(3): 331.

    [18] ZHOU Ruoyu, ZHOU Qing. Structure and assembly technology of the domestic first double shield TBM [J]. Construction Machinery, 2016(5): 61.

    [19]CAO Cuichen, MENG Jinzhong, FAN Anshun, et al. Development of TBM in China and abroad and its application in YRDP [J]. Water Resources and Hydropower Engineering, 2001, 32(4): 27.

    [20] YU Xinhong, CHEN Yongzhang, YAN Kai. Development and prospect of TBM tunneling technology [J]. Water Conservancy and Hydropower Project Cost, 2003(1): 45.

    [21] XUE Beifang. Current state and development strategy of shield TBM in China [J]. World Tunnelling, 1999(6): 26.

    [22] QIAN Qihu, LI Chaofu, FU Deming. Spreading the use of TBM, promoting development of underground space in China [J]. Construction Machinery, 2002(5): 28.

    [23] YAN Jinxiu, WANG Jianyu, FAN Wentian. Technological development and current application of TBM [J]. World Tunnelling, 1998(4): 1.

    [24]REYNOLDS P. Latest progress in construction of TBM tunnel of hydropower project [J]. Translators: MENG Zhaowei, MA Guisheng. Express of Water Resources & Hydropower Information, 2016, 37(4): 24.

    [25]XIE Wenqing. Mechanism of rock-burst in underground works and countermeasures [J]. Modern Tunnelling Technology, 2008, 45(4): 8.

    [26] LIU Shaobao, LI Cangsong, DING Jianfang, et al. Forecasting technologies of ground water with TBM construction [J]. Chinese Journal of Engineering Geophysics, 2009(S1): 117.

    [27] CHEN Yuan. Research on key technology of TBM selection and construction [D]. Shijiazhuang: Shijiazhuang Tiedao University, 2015.

    [28] CHEN Kui, YANG Yandong. Discussion on design of TBM with high adaptability to Gaoligongshan Tunnel [J]. Tunnel Construction, 2016, 36(12): 1523.

    [29] DU Lijie. Progresses, challenges and countermeasures for TBM construction technology in China [J]. Tunnel Construction, 2017, 37(9): 1063.

    [30]WANG Yusuo, YANG Chao, YE Yuezhong, et al. Experimental study of stress characteristics of lining structures of tunnels in high geo-temperature environment [J]. Tunnel Construction, 2013, 33(10): 809.

    国产精品久久久久久久久免| 国产av精品麻豆| 亚洲人成网站在线播| 国产免费一区二区三区四区乱码| 国产亚洲欧美精品永久| 男女边摸边吃奶| 国产av码专区亚洲av| 亚洲精品成人av观看孕妇| a级毛片免费高清观看在线播放| 制服丝袜香蕉在线| 中文字幕久久专区| 高清欧美精品videossex| 精品国产三级普通话版| 国产成人精品久久久久久| 18+在线观看网站| 熟妇人妻不卡中文字幕| 国产精品久久久久久精品电影小说 | av免费在线看不卡| 久久精品久久久久久噜噜老黄| 国产精品一区二区在线观看99| 黄色欧美视频在线观看| 免费少妇av软件| 伊人久久国产一区二区| 综合色丁香网| 男女边吃奶边做爰视频| 又粗又硬又长又爽又黄的视频| 久久久成人免费电影| 国产精品无大码| 色5月婷婷丁香| 国产精品久久久久久久久免| 亚洲欧美日韩卡通动漫| 菩萨蛮人人尽说江南好唐韦庄| av在线蜜桃| 亚洲国产毛片av蜜桃av| 99热6这里只有精品| av卡一久久| 欧美性感艳星| 日本黄大片高清| 男女无遮挡免费网站观看| 男男h啪啪无遮挡| 一本色道久久久久久精品综合| 亚洲精品亚洲一区二区| av黄色大香蕉| 能在线免费看毛片的网站| 两个人的视频大全免费| 国产毛片在线视频| 亚洲不卡免费看| av不卡在线播放| 日韩三级伦理在线观看| 久久久亚洲精品成人影院| 国产毛片在线视频| 久久精品国产亚洲av天美| 大香蕉97超碰在线| 夫妻午夜视频| 天天躁夜夜躁狠狠久久av| 亚洲成人av在线免费| 91精品一卡2卡3卡4卡| 国产欧美日韩精品一区二区| 老司机影院成人| 有码 亚洲区| 十分钟在线观看高清视频www | 亚洲高清免费不卡视频| 亚洲国产欧美在线一区| 国产极品天堂在线| 亚洲色图av天堂| 久久婷婷青草| 中文字幕亚洲精品专区| 日本欧美国产在线视频| 久久影院123| 国产精品秋霞免费鲁丝片| 欧美日韩一区二区视频在线观看视频在线| av视频免费观看在线观看| 国产黄色免费在线视频| 日韩成人伦理影院| 久久精品国产鲁丝片午夜精品| 精品人妻熟女av久视频| 高清不卡的av网站| 免费不卡的大黄色大毛片视频在线观看| 欧美日韩在线观看h| 免费av不卡在线播放| 人妻制服诱惑在线中文字幕| 人妻一区二区av| 亚洲欧美成人精品一区二区| 国产伦理片在线播放av一区| 嘟嘟电影网在线观看| 久久国内精品自在自线图片| 噜噜噜噜噜久久久久久91| 亚洲av男天堂| 哪个播放器可以免费观看大片| 国产女主播在线喷水免费视频网站| 国产精品一区二区在线观看99| 亚洲人成网站在线观看播放| 91精品一卡2卡3卡4卡| 国产成人freesex在线| 亚洲中文av在线| 国产一区二区三区综合在线观看 | 99久久综合免费| 青青草视频在线视频观看| 夫妻午夜视频| 国产亚洲最大av| 中国国产av一级| 日韩精品有码人妻一区| 亚洲精品视频女| 欧美日韩综合久久久久久| 尾随美女入室| 欧美一级a爱片免费观看看| 女的被弄到高潮叫床怎么办| 亚洲人与动物交配视频| 成人漫画全彩无遮挡| 欧美少妇被猛烈插入视频| av一本久久久久| 亚洲色图综合在线观看| 黑人猛操日本美女一级片| 男女下面进入的视频免费午夜| 久久久久久九九精品二区国产| 人体艺术视频欧美日本| 九草在线视频观看| 日韩在线高清观看一区二区三区| 精品亚洲成国产av| 麻豆乱淫一区二区| 美女cb高潮喷水在线观看| 天美传媒精品一区二区| 最近中文字幕高清免费大全6| 日本猛色少妇xxxxx猛交久久| 国产欧美另类精品又又久久亚洲欧美| 国产极品天堂在线| 国产免费福利视频在线观看| 少妇高潮的动态图| 18+在线观看网站| 久久国产精品男人的天堂亚洲 | 97热精品久久久久久| 91久久精品国产一区二区成人| 寂寞人妻少妇视频99o| 亚洲国产精品999| h视频一区二区三区| 人人妻人人爽人人添夜夜欢视频 | 久久ye,这里只有精品| 亚洲精品色激情综合| 美女主播在线视频| 亚洲精品视频女| 人妻夜夜爽99麻豆av| 国产在线免费精品| 国产伦理片在线播放av一区| 青春草视频在线免费观看| 直男gayav资源| 成人二区视频| 少妇熟女欧美另类| 亚洲国产精品成人久久小说| 丰满少妇做爰视频| 高清不卡的av网站| 国产综合精华液| 精品一区在线观看国产| 一级片'在线观看视频| 高清日韩中文字幕在线| 又大又黄又爽视频免费| 亚洲欧美日韩无卡精品| freevideosex欧美| 永久网站在线| av网站免费在线观看视频| 另类亚洲欧美激情| 精品久久久噜噜| 国产日韩欧美亚洲二区| 亚洲av综合色区一区| 啦啦啦啦在线视频资源| 亚洲精品第二区| 久久精品国产亚洲网站| 欧美xxxx性猛交bbbb| 最近的中文字幕免费完整| 国产美女午夜福利| 啦啦啦啦在线视频资源| 婷婷色av中文字幕| 亚洲第一av免费看| 亚洲国产精品999| 99视频精品全部免费 在线| 免费观看在线日韩| 精品国产一区二区三区久久久樱花 | 高清欧美精品videossex| 大片免费播放器 马上看| 国产精品一区www在线观看| 国产精品久久久久久久久免| 国产亚洲av片在线观看秒播厂| 亚洲av不卡在线观看| 性色av一级| 国产无遮挡羞羞视频在线观看| 水蜜桃什么品种好| a 毛片基地| 水蜜桃什么品种好| 精品人妻熟女av久视频| 国产精品99久久99久久久不卡 | 一级二级三级毛片免费看| 久久ye,这里只有精品| 亚洲精品国产色婷婷电影| 国产综合精华液| 又粗又硬又长又爽又黄的视频| 亚洲精品乱久久久久久| 我要看日韩黄色一级片| 国产黄片视频在线免费观看| 青春草亚洲视频在线观看| 免费大片18禁| 校园人妻丝袜中文字幕| 人人妻人人添人人爽欧美一区卜 | 国内精品宾馆在线| 人妻少妇偷人精品九色| 一级黄片播放器| 国产精品久久久久久久久免| 内地一区二区视频在线| 国产亚洲av片在线观看秒播厂| 精品一品国产午夜福利视频| 欧美变态另类bdsm刘玥| 岛国毛片在线播放| 老司机影院毛片| 欧美精品一区二区大全| 夜夜看夜夜爽夜夜摸| 永久网站在线| 成人毛片a级毛片在线播放| 国内少妇人妻偷人精品xxx网站| 交换朋友夫妻互换小说| 91午夜精品亚洲一区二区三区| 亚洲精品乱码久久久久久按摩| 婷婷色麻豆天堂久久| 中文欧美无线码| 3wmmmm亚洲av在线观看| 免费播放大片免费观看视频在线观看| 日韩不卡一区二区三区视频在线| 久久99热这里只有精品18| 一本色道久久久久久精品综合| 国产亚洲午夜精品一区二区久久| 青春草亚洲视频在线观看| 最近中文字幕高清免费大全6| 51国产日韩欧美| 久久精品国产亚洲av天美| 亚洲国产精品999| 夫妻性生交免费视频一级片| 美女脱内裤让男人舔精品视频| 1000部很黄的大片| 少妇人妻 视频| 久久久成人免费电影| 日韩中文字幕视频在线看片 | 韩国高清视频一区二区三区| 国产一级毛片在线| 99久久人妻综合| 男女无遮挡免费网站观看| 亚洲第一av免费看| av专区在线播放| 国产精品一区二区在线观看99| 欧美日韩在线观看h| 欧美国产精品一级二级三级 | 视频区图区小说| 色吧在线观看| 午夜激情久久久久久久| 青青草视频在线视频观看| 日韩欧美精品免费久久| 亚洲欧美日韩另类电影网站 | h视频一区二区三区| 在线 av 中文字幕| 美女高潮的动态| 国产 一区 欧美 日韩| 久久毛片免费看一区二区三区| 肉色欧美久久久久久久蜜桃| 美女主播在线视频| 18禁在线播放成人免费| 狂野欧美白嫩少妇大欣赏| 欧美高清性xxxxhd video| 亚洲丝袜综合中文字幕| 国产高清不卡午夜福利| 亚洲真实伦在线观看| 一区二区三区精品91| 欧美日韩精品成人综合77777| 精品久久国产蜜桃| 国语对白做爰xxxⅹ性视频网站| 晚上一个人看的免费电影| 丝袜喷水一区| kizo精华| 一个人看的www免费观看视频| 高清黄色对白视频在线免费看 | 免费大片黄手机在线观看| 成年美女黄网站色视频大全免费 | 最近手机中文字幕大全| 99热6这里只有精品| 亚洲不卡免费看| 秋霞伦理黄片| 五月开心婷婷网| 精品人妻偷拍中文字幕| 中文天堂在线官网| 少妇人妻 视频| 黄色怎么调成土黄色| 国产中年淑女户外野战色| 亚洲四区av| 亚洲精品成人av观看孕妇| 在线观看人妻少妇| 亚洲国产精品999| 天堂中文最新版在线下载| 五月伊人婷婷丁香| 欧美国产精品一级二级三级 | 国产视频首页在线观看| 18禁裸乳无遮挡免费网站照片| 久久精品国产亚洲网站| 亚洲国产精品国产精品| 国产在线免费精品| 国产永久视频网站| 久久久久精品久久久久真实原创| 免费久久久久久久精品成人欧美视频 | 久久99热6这里只有精品| 新久久久久国产一级毛片| 熟女av电影| 男的添女的下面高潮视频| 少妇人妻 视频| 国产综合精华液| 韩国av在线不卡| a级一级毛片免费在线观看| 免费观看在线日韩| 高清日韩中文字幕在线| 久久综合国产亚洲精品| 婷婷色综合www| 日韩强制内射视频| 热99国产精品久久久久久7| 丝袜喷水一区| 亚洲精品日韩在线中文字幕| 日韩三级伦理在线观看| 日本av手机在线免费观看| 亚洲精品日本国产第一区| 在线亚洲精品国产二区图片欧美 | 日本vs欧美在线观看视频 | 国产精品一区二区在线不卡| 色视频www国产| 免费大片黄手机在线观看| 日韩不卡一区二区三区视频在线| 亚洲综合精品二区| 新久久久久国产一级毛片| 日本黄大片高清| 免费久久久久久久精品成人欧美视频 | 91精品一卡2卡3卡4卡| 国产精品国产三级专区第一集| 一级二级三级毛片免费看| 亚洲成人一二三区av| 免费大片黄手机在线观看| 欧美bdsm另类| 成人无遮挡网站| 中文字幕人妻熟人妻熟丝袜美| 亚洲成色77777| 色婷婷av一区二区三区视频| 精品久久久精品久久久| 老女人水多毛片| 中文天堂在线官网| 久久综合国产亚洲精品| 欧美 日韩 精品 国产| 国产白丝娇喘喷水9色精品| 成人毛片60女人毛片免费| 最新中文字幕久久久久| 亚洲自偷自拍三级| 亚洲高清免费不卡视频| 黄色视频在线播放观看不卡| 国产精品麻豆人妻色哟哟久久| 亚洲av中文字字幕乱码综合| 亚洲激情五月婷婷啪啪| 婷婷色综合大香蕉| 久久久久人妻精品一区果冻| 欧美成人a在线观看| av在线老鸭窝| 美女福利国产在线 | 精品一区二区三卡| 精品人妻偷拍中文字幕| 丰满乱子伦码专区| 免费黄色在线免费观看| kizo精华| 欧美日韩在线观看h| av国产精品久久久久影院| 欧美极品一区二区三区四区| 日韩国内少妇激情av| 黄片wwwwww| 天天躁日日操中文字幕| 九九爱精品视频在线观看| 最近中文字幕2019免费版| 免费不卡的大黄色大毛片视频在线观看| 男人爽女人下面视频在线观看| 国产伦精品一区二区三区四那| 蜜臀久久99精品久久宅男| 人人妻人人添人人爽欧美一区卜 | 高清视频免费观看一区二区| 又大又黄又爽视频免费| 精品一区二区三区视频在线| 伦精品一区二区三区| 亚洲精品日韩av片在线观看| 一区二区三区四区激情视频| av线在线观看网站| 我的老师免费观看完整版| 观看美女的网站| 国产爽快片一区二区三区| 99精国产麻豆久久婷婷| 国产精品一及| 高清欧美精品videossex| 亚洲精品国产av蜜桃| 99国产精品免费福利视频| 中文欧美无线码| 欧美一区二区亚洲| 免费看日本二区| 九草在线视频观看| 草草在线视频免费看| 最后的刺客免费高清国语| av在线老鸭窝| 两个人的视频大全免费| 色哟哟·www| 国产亚洲一区二区精品| 欧美区成人在线视频| 黑人高潮一二区| 欧美xxxx性猛交bbbb| 人妻一区二区av| 又大又黄又爽视频免费| 日本一二三区视频观看| 97超碰精品成人国产| 久久99蜜桃精品久久| 亚洲成人手机| 精品视频人人做人人爽| 又大又黄又爽视频免费| 热99国产精品久久久久久7| 国产欧美日韩精品一区二区| 汤姆久久久久久久影院中文字幕| 国产av国产精品国产| 亚洲av成人精品一区久久| 日韩av在线免费看完整版不卡| a级毛片免费高清观看在线播放| 国产精品伦人一区二区| 伦理电影大哥的女人| 日韩三级伦理在线观看| 日韩一区二区三区影片| 黄色配什么色好看| av免费在线看不卡| 国产精品99久久99久久久不卡 | 国产精品久久久久久精品古装| 在线精品无人区一区二区三 | 熟女人妻精品中文字幕| 亚洲,欧美,日韩| 在线观看三级黄色| 男人狂女人下面高潮的视频| 久久久欧美国产精品| 又大又黄又爽视频免费| 国产老妇伦熟女老妇高清| 国产淫语在线视频| 久久久午夜欧美精品| 青青草视频在线视频观看| 中文字幕人妻熟人妻熟丝袜美| 亚洲精品亚洲一区二区| 女人十人毛片免费观看3o分钟| 丰满人妻一区二区三区视频av| 又粗又硬又长又爽又黄的视频| 免费在线观看成人毛片| 国产午夜精品一二区理论片| 男的添女的下面高潮视频| 精品久久久久久久久av| 简卡轻食公司| 日韩在线高清观看一区二区三区| 国产黄色免费在线视频| av在线播放精品| 国产欧美日韩一区二区三区在线 | 亚洲一级一片aⅴ在线观看| 日韩欧美精品免费久久| 日韩在线高清观看一区二区三区| 国内揄拍国产精品人妻在线| 简卡轻食公司| 国产一区二区三区综合在线观看 | 看非洲黑人一级黄片| 男人和女人高潮做爰伦理| 亚洲无线观看免费| 国产精品一及| 久久精品久久久久久久性| 久久国产精品大桥未久av | 免费不卡的大黄色大毛片视频在线观看| 亚洲精品成人av观看孕妇| 久久国产精品大桥未久av | 久久99热这里只有精品18| 国产老妇伦熟女老妇高清| .国产精品久久| 卡戴珊不雅视频在线播放| 高清视频免费观看一区二区| 久久久精品94久久精品| 青春草视频在线免费观看| 久久久久久伊人网av| 超碰97精品在线观看| 我的老师免费观看完整版| 最近中文字幕高清免费大全6| a级一级毛片免费在线观看| 国产精品av视频在线免费观看| 啦啦啦啦在线视频资源| 亚洲一区二区三区欧美精品| 国内精品宾馆在线| 黑丝袜美女国产一区| 国产免费视频播放在线视频| 日韩国内少妇激情av| 欧美一区二区亚洲| 91精品一卡2卡3卡4卡| 国产亚洲午夜精品一区二区久久| 国产成人a区在线观看| 99久久中文字幕三级久久日本| 熟妇人妻不卡中文字幕| 精品久久久久久久久亚洲| 国产精品伦人一区二区| 日本av免费视频播放| 青春草国产在线视频| 亚洲激情五月婷婷啪啪| 国产精品久久久久久精品电影小说 | 亚洲精品日韩av片在线观看| 色视频www国产| 久久99蜜桃精品久久| 亚洲精品成人av观看孕妇| 亚洲激情五月婷婷啪啪| 久久久久国产精品人妻一区二区| 久久久亚洲精品成人影院| 成年人午夜在线观看视频| 纵有疾风起免费观看全集完整版| 日本欧美国产在线视频| 欧美三级亚洲精品| 日本欧美国产在线视频| 高清午夜精品一区二区三区| 久久久色成人| 国产黄频视频在线观看| 国产日韩欧美亚洲二区| 狂野欧美激情性xxxx在线观看| 亚洲中文av在线| 亚洲精品日本国产第一区| 久久99蜜桃精品久久| 极品少妇高潮喷水抽搐| 狂野欧美激情性xxxx在线观看| 国产黄片美女视频| 日韩 亚洲 欧美在线| 精品国产乱码久久久久久小说| tube8黄色片| 丰满迷人的少妇在线观看| 欧美最新免费一区二区三区| 最近的中文字幕免费完整| 少妇丰满av| 免费人成在线观看视频色| 嫩草影院新地址| 成年美女黄网站色视频大全免费 | 国内精品宾馆在线| 日本av免费视频播放| 最近最新中文字幕大全电影3| 激情 狠狠 欧美| 久久久久久久久久人人人人人人| 97精品久久久久久久久久精品| 26uuu在线亚洲综合色| 日韩电影二区| 女人十人毛片免费观看3o分钟| 1000部很黄的大片| 女的被弄到高潮叫床怎么办| 一边亲一边摸免费视频| 国产成人精品福利久久| 黄色视频在线播放观看不卡| 日韩精品有码人妻一区| 成人午夜精彩视频在线观看| 亚洲成人手机| 午夜日本视频在线| 又爽又黄a免费视频| 久久ye,这里只有精品| 夫妻性生交免费视频一级片| 秋霞在线观看毛片| 国产精品一及| 麻豆成人av视频| 大香蕉97超碰在线| 少妇人妻一区二区三区视频| 夜夜爽夜夜爽视频| 亚洲欧美日韩卡通动漫| 午夜福利高清视频| 久久精品国产亚洲av天美| 精品一区在线观看国产| 欧美日韩综合久久久久久| 国产视频内射| 免费不卡的大黄色大毛片视频在线观看| 国产成人一区二区在线| 热99国产精品久久久久久7| 日本午夜av视频| 免费人成在线观看视频色| 国产成人免费无遮挡视频| 日韩一本色道免费dvd| 亚洲国产精品国产精品| 亚洲国产精品一区三区| 欧美三级亚洲精品| 91精品国产九色| 亚洲内射少妇av| 一个人看的www免费观看视频| 免费黄色在线免费观看| av免费在线看不卡| 99re6热这里在线精品视频| 女性被躁到高潮视频| 久久精品久久久久久噜噜老黄| 80岁老熟妇乱子伦牲交| 一级毛片我不卡| 精品人妻视频免费看| 免费人成在线观看视频色| 毛片一级片免费看久久久久| 2022亚洲国产成人精品| 免费黄频网站在线观看国产| 久久99热这里只频精品6学生| 国产高潮美女av| 国产深夜福利视频在线观看| 舔av片在线| 久久人妻熟女aⅴ| 在线亚洲精品国产二区图片欧美 | 一级毛片 在线播放| 99re6热这里在线精品视频| 国产淫片久久久久久久久| 一区二区av电影网| 欧美日本视频| 99久国产av精品国产电影| 3wmmmm亚洲av在线观看| 小蜜桃在线观看免费完整版高清| 亚洲va在线va天堂va国产| 哪个播放器可以免费观看大片| h视频一区二区三区| 丰满少妇做爰视频| 成人黄色视频免费在线看| 蜜桃久久精品国产亚洲av| 欧美少妇被猛烈插入视频| 熟女电影av网| 亚洲国产成人一精品久久久| 亚洲精品国产色婷婷电影|