• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Freezing Process Simulation of Standing Water Droplets Under Different Supercooling and Contact Angles

    2023-12-19 08:13:26,-,-,
    船舶力學 2023年12期

    ,-,-,

    (School of Naval Architecture&Ocean Engineering,Jiangsu University of Science and Technology,Zhenjiang 212003,China)

    Abstract: In order to eliminate danger and to reduce the frequency of ship accidents caused by ice forming on ship decks and superstructures,it is important to have a physical understanding and the ability to predict icing.By studying the freezing stages in an icing process, the influence of different parameters on the icing process is analyzed, which provides a theoretical basis for the prediction of ship icing.In this paper, the proportion of the ice phase after the water droplet recalescence stage is calculated, the water droplet profiles at different stages are discussed, and the freezing time of water droplets at different supercooling degrees and contact angles is simulated by Fluent.The results show that both the supercooling degree and the contact angle have a great influence on the freezing time of water droplets.The decrease of supercooling degree and the increase of freezing time are approximately exponential functions, and the increase of contact angle is also exponential functions for the increase of freezing time.

    Key words:ship icing;ice phase proportion;supercooling;contact angle;freezing time

    0 Introduction

    Ships operating in polar environments often face the problem of superstructure icing caused by marine droplets.A large amount of icing will affect the stability of offshore structures and the maneuverability of deck equipment, and even endanger the safety of personnel[1].Therefore, the polar ship icing problem has attracted the attention of scholars in recent years.Atmospheric icing and sea spray icing are the two types of marine icing in cold ocean regions and more than 80% of the icing events are caused by sea spray[2].The prediction model of ice accretion on offshore structures has been extensively studied and is largely based on empirical formulas and data statistics[3].Both air and sea spray icing involve the transmission of heat and the freezing of droplets.Moreover,since the freezing process of water droplets is extremely sensitive, any external disturbance will affect the final ice type (bright ice,frost ice and mixed ice) and physical property parameters[4].Meanwhile,the surface characteristics of materials will also have an impact on the adhesion and icing results of ice accumulation.Therefore, in order to obtain accurate prediction results of ship icing, it is necessary to consider the microscopic icing process of water droplets on the surface, and analyze the icing results of water droplets under different parameters from the microscopic perspective,so as to provide a certain theoretical basis and technical reference for future research on ship icing prediction and improvement of anti-icing/deicing related engineering applications.

    In recent years,progress has been made in the simulation of water droplet icing by using phase field and numerical methods.The phase field approach, which is based on Ginzburg-Landau theory, is a simulation technique that uses differential equations to represent the diffusion, ordering potential, and mechanical driving processes of matter[5].Bai[6]used the finite difference approach based on the Wheeler phase field model to estimate how saltwater would solidify at various supercooling temperatures.Fan[7]developed a phase field model to explain the development of ice crystals and dynamics of mesoscale freezing concentration based on the average field approximation of solute concentration and the transport phenomena of latent heat, mass, and momentum.Han[8-9]developed a computational model to simulate the formation of hexagonal ice crystals from pure water.Then,based on Wheeler model,the numerical simulation of sea water ice crystal was realized by using sea water physical parameters,which provided a theoretical basis for the rewiring stage of supercooled water droplet freezing and further revealed the freezing mechanism.The phase field method is mostly used to study the nucleation and recalescence stage of the freezing process of water droplets.For the research of the freezing stage of static water droplets,the main methods adopted now include theoretical model and numerical simulation.Hindmarsh[10]further compared two kinds of spherical supercooled water droplet freezing models.After comparing the water droplet temperature change curve calculated by the model with the experimental measured value, it was found that the model with the phase interface moving from the inside to the outside was more practical.Zhang[11]adopted the equivalent specific heat capacity method based on the initial profile of water droplets.It was found that the surface contact angle would seriously affect the freezing process of water droplets.For water droplets of a given size, the freezing time increased exponentially with the increase of the wall contact angle.Tryggvason[12]combined the front tracking method and the finite difference method to numerically simulate the freezing process of a single droplet on the wall, and well reproduced the contour change of the droplet freezing process.Zhang[13]conducted a freezing experiment of 10 μL water droplets on a cold wall surface with a temperature of -16.5 ℃, capturing the evolution of the solid-liquid interface inside the droplets during the freezing process.Compared with the hydrophilic surface, the results of the hydrophobic surface are in good agreement with the experimental results.As mentioned above, when studying the microscopic freezing process of water droplets, the recalescence process is often ignored, or the recalescence phenomenon is only observed,without associating it with the freezing stage.

    The main objective of this paper is to establish a model to simulate the freezing of static water droplets.The model introduces the influence of the degree of supercooling on the recalescence stage and considers the influence of the recalescence stage on the freezing process of the droplet,which affects the initial physical parameters of the main freezing stage of the droplet.Calculation of ice phase proportion by recalescence phase with phase field method according to the result after the recalescence and freeze phase droplets by physical parameters, the solidification/melting model by using FLUENT software to different degree of supercooling and contact angle of the static water ice freezing process simulation, and system analysis of the different degree of supercooling and contact angle influence on freezing stage,provide a theoretical basis for ship icing prediction and anti-icing research.

    1 Frozen water drop theory

    As shown in Fig.1,the frozen water droplets can be divided into five stages:liquid cooling,nucleation, recalescence, freezing and solid cooling[14].In the stage of liquid cooling and nucleation, the droplet gradually cools down on the cold surface until the temperature reaches the critical nucleation temperature, and then spontaneously growing crystal nuclei larger than the critical size are randomly formed inside the droplet.The supercooling degree of the supercooled water droplet is released during the freezing phase, and its internal temperature maintains the temperature of the ice water mixture throughout the freezing phase.The recalescence stage is the process of the growth and release of heat of the crystal nucleus after the nucleation of the water droplet in the supercooling.Meanwhile, the interface of the ice water phase gradually advances from the bottom to the top of the droplet until it is completely frozen under the continuous drive of the cold surface, which lasts a long time.The solid cooling phase is the last stage of the freezing process,when the temperature inside the droplet slowly decreases again until it is the same as the cold surface temperature.

    1.1 Recalescence process calculation

    During the liquid solidification process,the latent heat will be released when the water changes from liquid phase to solid phase, which will be transferred to the supercooled liquid around the solid phase through the solid-liquid interface.In the process of liquid solidification, the generation of latent heat and the cooling of liquid surface to the surrounding environment compete with each other,and the temperature of liquid depends on the results of competition between the two processes.After the supercooled liquid begins to solidify, the solidification rate is usually fast.Therefore,the heat release rate from the solid-liquid interface to the supercooled liquid is much faster than the heat dissipation rate from the liquid surface to the surrounding environment, which will lead to the increase of the liquid temperature , namely the recalescence phenomenon of the liquid.In this paper,the phase field method is used to calculate the recalescence stage.

    The phase field equation is:

    whereΔis dimensionless subcooling degree,Δ=cΔT/L,cis sensible heat,Lis latent heat per unit volume,mis phase field mobility,ais interfacial free energy.

    The temperature field equation[15]is:

    where,p(?)=?3(10 - 15?+ 6?2),uis dimensionless temperature,u=(T-TM)/(TM-T0).

    This paper focuses on the solidification of water droplets in the polar region.Considering that most of the polar regions are iced seawater,seawater is regarded as a binary solution.In the process of seawater solidification, since the solubility of solute salt in water is greater than that in ice, the solute will be enriched at the front of the solid-liquid interface.As the interface advances, the solid-liquid interface will discharge solute to the liquid phase, which will affect the solidification process.Therefore,the effect of solute redistribution should be introduced in the simulation.

    Based on Fick's Law[16], the solute field equation is introduced to realize the solute change in the computational domain during solidification:

    whereCis mol fraction of salt in seawater,Dis dimensionless diffusion coefficient.

    The phase field equation after adding solute is:

    The temperature field equation is:

    1.2 Solidification and melting model

    In this paper, the solidification/melting model in Ansys-Fluent is used for numerical simulation of freezing stage of water droplet solidification[17].In this model, the enthalpy-porous medium technology is used to solve the solidification or melting problem at a certain temperature.By calculating the enthalpy balance of each cell in the computational domain,the liquid fraction of the fluid is obtained.When the liquid fraction is between 0 and 1, the solid and liquid coexist in the region.When the liquid fraction is 0, the fluid is completely solidified, and the porosity and velocity in the solid-liquid coexistence region are 0[18].

    In the system,the total enthalpyhtotalof the material is:

    wherehis apparent enthalpy,htotalis the latent heat of the material after solid-liquid mixing.

    The latent heat after solid-liquid mixing is:

    whereαliquidis the liquid fraction in the region where phase transition occurs, andLmixis latent heat for materials.

    The solidification/melting model regards the phase transition zone as a porous medium,and its internal flow conforms to the Darcy flow law and Carman-Koseny assumption.Therefore,the source termS→Mof momentum equation for phase transition process is introduced:

    whereεis the minimum value to prevent denominator from being 0,Amushis the coefficient of solidliquid mixing zone,which is related to the porosity of porous media.

    2 Numerical method

    2.1 Outline of water droplets

    2.1.1 Water droplet profile in initial stage Fig.2 is the outline of water droplets at the initial stage.V0is the volume of water droplets,R0is the base radius,H0is water droplet height, andθ0is contact angle.

    Before calculating the water droplet profile, the droplet is generally regarded in an ideal state, so several hypotheses need to be made:

    (1) When the water drop is standing on the cold surface, it is rotating symmetrically,and its axis of rotation is vertical;

    (2)The convective heat transfer between water droplets and air can be ignored;

    (3)The volume of water droplets is not affected by evaporation or condensation.

    Usually,the volume range of droplets in ship icing is 10-1000 μL[19].In order to meet the actual requirements and facilitate the calculation,the droplet volume of 10 μL is selected in this paper for subsequent water droplet solidification calculation.

    For static water droplets,the base radius and water droplet height can be calculated by the volume and contact angle of water droplets.

    Fig.2 Initial stage droplet profile

    whereRNis the base radius,HNis the height of water droplets,Vis the volume of water droplets,andθis the wall contact angle.

    In this research, the contact angles are 30°, 60°, 90°, 120° and 150°.Combined with the volume of water droplets, the initial contours of standing water droplets under different contact angles could be obtained.

    2.1.2 Water droplet profile after recalescence stage

    Fig.3 is the outline of water droplets after recalescence stage.At the end of the recalescence stage, a uniform mixture of ice and water is formed inside the droplets.Due to the different densities of ice and water, the volume water of the droplets is enlarged toVN, the height becomesHN,the radius of the substrate becomesR,and the contact angle remains unchanged[20].

    It can be seen from Fig.3 that the outline of water droplets has changed after the recalescence stage, so the outline of water droplets need to be recalculated.The density of ice-water mixture after recalescence can be calculated by the proportion of ice phase and the density of ice and water.Then,the volumeVNof water droplets after recalescence can be calculated by the initial volume of water droplets and the density of ice-water mixture.

    Fig.3 Contour of water droplets after the recalescence phase

    whereρminis the mixing density of ice water,ρwis water density,ρiis ice density,andγiis ice ratio.

    With the volume of the droplet obtained after the recalescence stage, it is substituted into Eqs.(1)-(2)to calculate the base radius and height of the water droplet after recalescence.

    After the recalescence stage, the droplet has become a uniform ice-water mixture, and its physical parameters also change accordingly.To calculate accurately, its physical parameters need to be processed.The physical parameters of water droplets,such as latent heat,specific heat capacity and thermal conductivity,are recalculated by Eq.(13).

    2.2 Solidification simulation condition

    2.2.1 Parameter setting of recalescence stage

    Setting square grid of 1000×1000 for phase field simulation, grid spacing Δxand Δyare dimensionless 0.03,time step Δt= 0.0001 s.

    In order to ensure the convergence of the results, the time step and grid spacing should meet the following conditions[21]:

    2.2.2 Parameter setting for cooling stage

    The software used in the solidification model of water droplets is the solidification/melting model in Fluent.In the freezing stage,due to the limitation of the model,the contour change caused by the volume change in the process of water droplet freezing cannot be reflected.Therefore, the change of density with temperature is added to the physical parameters of the material,so as to calculate the volume change of water droplet freezing in the subsequent work.The density change in freezing is based on the density change of ice with temperature[22].In this paper, the test results are fitted, and the fitting formula of temperature and density is applied to the material attribute setting in Fluent.

    whereρSis the ice density during freezing,andTSis the ice temperature.

    The model used in this simulation is shown in Fig.4.The temperature of the cold surface is set as the freezing temperature, and the temperature inside the water droplets is set as the temperature of the ice-water mixture.Since the reference is the seawater with a salinity of 3.5%, the temperature inside the water droplets is set to 270.85 K according to the salt water solidification point.

    Simulation calculation is transient calculation.Pressure-based solver is selected.The velocity and pressure are coupled by SIMPLE method.The momentum and energy equations are discretized by Second Order Upwind scheme with a time step of 0.1 μs.In order to save calculation resources and improve calculation accuracy, the mesh size of 0.02 μm is selected for subsequent simulation.Fig.5 shows the flow chart of numerical simulation.

    Fig.4 Physical modeling and boundary demarcation

    Fig.5 Numerical simulation flow chart

    2.3 Model validation

    In this paper, the solidification/melting model in ANSYS-Fluent software is used for simulation.In order to verify the accuracy and effectiveness of the model,simulation is carried out according to the experimental conditions ΔT= 16.5 K,θ= 90°, and the step size is set to 0.01 s.(where ΔTrepresents the supercooling andθrepresents the contact angle.)

    As shown in Fig.6(a),Zhang[13]carried out the freezing process experiment of static water droplets on the cold surface.The experimental results are compared with those in the literature, as shown in Fig.6(b).It can be seen that the variation trend of the simulated liquid-solid interface is consistent with that obtained by experimental photography.

    In order to quantitatively compare the simulation results with the experimental results in the literature, the desired interface height during the droplet freezing process is treated as infinite toughening (the desired interface height at any time/the desired interface height at the end of solidification and freezing).As shown in Fig.7, from the variation of the dimensionless phase interface height with time obtained by experiments and simulations in the literature, it can be seen that the two are generally consistent in trend.In terms of the final freezing time, the experimental value in the literature is 9.2 s,and the simulated value is 10.2 s,with a deviation of 9.8%.

    From the shape and height of the phase interface,the simulation and experimental trends are in good agreement, indicating that the model can be used to simulate the freezing process of supercooled droplets.

    3 Numerical results and discussion

    Fig.7 Comparison of calculated and experimental values[13] of dimensionless plane interfaces

    3.1 Ice phase ratio

    3.1.1 Ice phase ratio under different supercooling

    Fig.8 shows the proportional growth of ice phase at each supercooling.The growth rate of ice phase ratio is related to supercooling.The greater the supercooling,the greater the growth rate of ice phase ratio.There is a threshold for the proportion of ice phase in the recalescence process.When the proportion of ice phase increases to a certain value,it will no longer change.This is because,as the recalescence process continues to release heat,the temperature in the entire calculation domain continues to rise.After the final temperature reaches the freezing point, it cannot continue to rise,and ice crystals cannot continue to grow.The ice phase ratio reaching the threshold represents the end of the recalescence stage.At this time,a uniform ice-water mixture has been formed inside the droplet, and the temperature in the calculation domain reaches the freezing point at the same time.Tab.1 is the ice phase ratio of partial supercooling.

    Fig.8 Proportion of ice phase changing with time

    Tab.1 Proportion of ice phases for each degree of supercooling

    3.1.2 Droplet profile under ice phase ratio

    Tab.2 and Tab.3 show droplet height and radius under different supercooling and contact angles.From Tab.2, it can be seen that as the subcooling increases, the proportion of ice phase increases, and the height and radius of water droplets also increase.The height and radius of water droplets are consistent.It can be seen from Tab.3 that with the increase of supercooling degree,both the proportion of ice phase and the height of water droplets increase, but the radius of water droplets decreases.

    Tab.2 Droplet height and radius at different degrees of supercooling

    Tab.3 Droplet heights and radii under different contact angles

    Fig.9 shows the droplet profile under different supercooling.Under different supercooling, the contour gap of the droplet is not obvious compared with the overall contour.This is because different supercooling only affects the ice phase ratio of the droplet,and the influence of the ice phase ratio on the volume of the droplet is not obvious compared with the original volume,so the supercooling has little effect on the contour of the droplet.

    Fig.9 Droplet profiles at different degrees of supercooling

    It can be seen from Fig.10 that when the contact angles are different, the contour of the droplet is quite different from the overall contour.This is because when the contact angle is different, the radius and height of water droplets have changed greatly, which directly affects the contour of water droplets.

    3.2 Simulation results of icing

    The supercooling degree is 30 K and the contact angle is 90°when the near order of water droplet freezing is simulated.The freezing completion time is 33.8 μs.The simulation results are shown in Fig.11.It can be seen from the figure that the solid-liquid interface is basically a straight line when advancing upward, only inside the droplet near the surface of the droplet.Due to the tension, the solid-liquid interface presents a certain bending angle.In the freezing stage, the initial solid-liquid boundary advances faster at first, then slows down.This is because the heat transfer efficiency is different before and after the whole process.In the initial stage of freezing, the solid-liquid interface is close to the cold surface.The heat transfer from the solid-liquid interface to the cold surface is faster, and the release rate of solidification latent heat is faster.After that, the solid-liquid interface is gradually moving away from the cold surface,and the distance becomes larger,and the release of latent heat slows down.At the same time,due to the different cooling rates in the droplet,the closer to the solid-liquid interface,the higher the temperature of the droplet, which leads to the temperature inside the droplet higher than that of the cold surface,and further inhibits the heat transfer efficiency.

    Fig.10 Droplet profiles at different contact angles

    Fig.11 Droplet freezing process at a subcooling degree of 30 K

    3.3 Effect of supercooling on icing

    Tab.4 and Fig.12 are the freezing time of droplets under different degrees of supercooling.It can be seen from Tab.4 that with the increase of supercooling degree, the freezing time is gradually shortened.The supercooling degree is changed from 45 K to 30 K, and the freezing time is shortened from 33.8 μs to 24.6 μs.It can be seen from Fig.9 that the larger the supercooling degree is,the smaller the reduction of freezing time is,which indicates that the supercooling degree has a significant impact on the freezing time in the freezing stage.After converting the supercooling degree into the temperature condition, it can be found that with the temperature increase, the relationship between freezing time and temperature is approximately exponential function.

    Tab.4 Droplet freezing time at different degrees of supercooling

    Fig.12 Droplet freezing time at different degrees of supercooling

    3.4 Effect of contact angle on icing

    The influence of contact angle on supercooled water droplets in freezing stage is simulated.A total of five contact angles of 30°, 60°, 90°, 120° and 150° are selected, and the supercooling degree is 30 K.

    Fig.13 is the images of supercooled water droplets freezing process under different contact angles.It can be seen from the figure that under different contact angles, at the interface between the solid-liquid interface and the droplet surface,the angle between the interface and the outer surface of the droplet is approximately 90°.The solid-liquid interface inside the droplet is different in shape.When the contact angle is 30°-90°, the solid-liquid interface at the contact position of the interface and the outer surface is almost linear except the contact position.However, when the contact angle increases to 120°, although the solid-liquid interface is still advancing as a whole, the overall morphology of the solid-liquid interface changes from almost a straight line to a small bending.When the contact angle is 150°,the solid-liquid interface shows an obvious bending.

    Fig.13 Freeze under different contact angles

    Tab.5 and Fig.14 show the droplet freezing time under different contact angles.Droplets with different contact angles have great differences in freezing time.The contact angle increases from 30° to 150°, and the freezing time increases from 8.02 μs to 95.6 μs, increasing by 1092.02%.Compared with supercooling, the contact angle has a greater impact on the freezing stage of water droplets.The larger the contact angle,the longer the freezing time.This is because when the contact angle is small, the contact area between the droplet and the cold surface is larger, which is more conducive to heat conduction.At the same time, because the droplet height is small, the distance between the solid-liquid interface needing to be promoted is shorter, which further reduces the freezing time and makes the freezing faster.When the contact angle is large,not only the contact area between the droplet and the cold surface is smaller, which slows down the heat transfer efficiency,but also the distance between the solid-liquid interface needing to be promoted is longer,which leads to a longer freezing time.

    Tab.5 Droplet freezing time at different contact angles

    Fig.14 Droplet freezing time at different contact angles

    With the influence of supercooling degree combined with contact angle on freezing time, it is found that supercooling degree and contact angle have a great influence on freezing time, and they are exponential function.

    4 Conclusions

    A numerical framework was established to consider the effect of the ice-phase ratio on the freezing of water droplets after the recalescence stage.By tracing the solid-liquid interface, the freezing process of static supercooled water droplets on a cold surface was studied.The influence of surface contact angle and subcooling degree on water droplet freezing was analyzed.The main conclusions are as follows:

    (1) Under different subcooling degrees, the contour difference of water droplets is not obvious compared with the overall contour.When the contact angles changes, compared with the overall contour,the contour difference of water droplets is very obvious.

    (2) The growth rate of ice phase ratio is related to supercooling, and the greater the supercooling,the greater the growth rate of ice phase ratio.

    (3) The degree of supercooling and the contact angle have a great influence on the freezing of stationary droplets.Freezing time decreases exponentially with the increase of subcooling degree.When the supercooling is 30 K,the freezing time is 33.8 μs,and when the supercooling is 45 K,the freezing time is 24.6 μs.The influence of contact angle on the freezing time is also close to exponential function.The contact angle increases from 30° to 150°, and the freezing time increases from 8.02 μs to 95.6 μs.

    This model can serve as a reference for the prediction of ice on the surface of superstructures.

    亚洲精品美女久久久久99蜜臀| 成年人免费黄色播放视频| 亚洲视频免费观看视频| 啪啪无遮挡十八禁网站| 夜夜夜夜夜久久久久| 中文字幕最新亚洲高清| 国产精品一区二区在线不卡| 国产精品欧美亚洲77777| 午夜久久久在线观看| 夫妻午夜视频| 久久国产精品影院| 黄片小视频在线播放| 亚洲国产精品一区二区三区在线| 欧美一级毛片孕妇| www日本在线高清视频| 国产欧美日韩一区二区三区在线| 精品电影一区二区在线| 黄色 视频免费看| 亚洲中文字幕日韩| 在线观看免费视频网站a站| 日韩欧美免费精品| 老司机福利观看| 精品久久久精品久久久| 午夜影院日韩av| 亚洲av电影在线进入| 18禁裸乳无遮挡免费网站照片 | 纯流量卡能插随身wifi吗| 精品一区二区三卡| 大型av网站在线播放| 老司机午夜十八禁免费视频| 国产在视频线精品| 精品国产一区二区三区四区第35| 老鸭窝网址在线观看| 后天国语完整版免费观看| 成人手机av| 丝袜人妻中文字幕| 婷婷丁香在线五月| 水蜜桃什么品种好| 欧美激情 高清一区二区三区| 色精品久久人妻99蜜桃| 久久热在线av| 精品福利观看| 欧美不卡视频在线免费观看 | 久久热在线av| 国产无遮挡羞羞视频在线观看| 一进一出好大好爽视频| 亚洲人成电影观看| 亚洲 欧美一区二区三区| 999精品在线视频| 99国产极品粉嫩在线观看| 韩国精品一区二区三区| 午夜精品国产一区二区电影| 精品国产一区二区三区四区第35| 一级,二级,三级黄色视频| 多毛熟女@视频| 午夜激情av网站| 久久精品熟女亚洲av麻豆精品| 高清黄色对白视频在线免费看| 久久草成人影院| 精品少妇久久久久久888优播| 99国产精品99久久久久| 91精品国产国语对白视频| 久久 成人 亚洲| 激情视频va一区二区三区| 日韩欧美一区二区三区在线观看 | 9191精品国产免费久久| 精品亚洲成a人片在线观看| 国产av精品麻豆| 一级作爱视频免费观看| 如日韩欧美国产精品一区二区三区| 国产欧美日韩综合在线一区二区| 国产欧美日韩综合在线一区二区| 伦理电影免费视频| 久久久久久人人人人人| 国产男女超爽视频在线观看| 午夜久久久在线观看| 一二三四在线观看免费中文在| 一区二区日韩欧美中文字幕| 久久精品91无色码中文字幕| x7x7x7水蜜桃| 少妇的丰满在线观看| 久久草成人影院| 亚洲欧美日韩高清在线视频| 国产精品久久久久成人av| 91成人精品电影| 91av网站免费观看| 国内久久婷婷六月综合欲色啪| 九色亚洲精品在线播放| 国产免费av片在线观看野外av| 国产成人精品无人区| 日韩有码中文字幕| 色婷婷av一区二区三区视频| av网站在线播放免费| 夜夜躁狠狠躁天天躁| 亚洲精品国产区一区二| 亚洲精品粉嫩美女一区| 国产成人欧美在线观看 | 午夜福利在线观看吧| 熟女少妇亚洲综合色aaa.| 免费观看精品视频网站| netflix在线观看网站| 精品久久久精品久久久| 亚洲精品中文字幕在线视频| 一个人免费在线观看的高清视频| 成人三级做爰电影| 在线观看www视频免费| 日韩三级视频一区二区三区| 性少妇av在线| 一边摸一边抽搐一进一出视频| 久久精品aⅴ一区二区三区四区| 国产精品.久久久| 欧美日韩乱码在线| 麻豆av在线久日| 欧美丝袜亚洲另类 | 欧美日韩黄片免| 热re99久久精品国产66热6| 波多野结衣av一区二区av| 狠狠婷婷综合久久久久久88av| 国产亚洲欧美精品永久| 妹子高潮喷水视频| 国产精品自产拍在线观看55亚洲 | 另类亚洲欧美激情| 免费在线观看黄色视频的| 免费观看精品视频网站| 欧美日韩瑟瑟在线播放| 在线观看免费视频日本深夜| 大型黄色视频在线免费观看| 国产精品免费一区二区三区在线 | 午夜激情av网站| 欧美黄色片欧美黄色片| 国产97色在线日韩免费| 国产亚洲精品久久久久久毛片 | 午夜福利影视在线免费观看| 欧美+亚洲+日韩+国产| 在线观看免费视频网站a站| 日韩欧美三级三区| 亚洲av电影在线进入| 男人操女人黄网站| 不卡av一区二区三区| 国产高清激情床上av| 亚洲人成电影观看| 精品卡一卡二卡四卡免费| 精品一区二区三卡| 欧美乱妇无乱码| 午夜免费鲁丝| 一二三四在线观看免费中文在| 在线观看www视频免费| 欧美精品高潮呻吟av久久| 美女高潮到喷水免费观看| 国产成人免费观看mmmm| 麻豆成人av在线观看| 精品人妻熟女毛片av久久网站| 美女 人体艺术 gogo| 超碰成人久久| 成年动漫av网址| 国产有黄有色有爽视频| 欧美成狂野欧美在线观看| 国产精品亚洲av一区麻豆| 国产成人精品久久二区二区免费| 国产日韩欧美亚洲二区| 在线观看午夜福利视频| 在线观看舔阴道视频| 国产主播在线观看一区二区| 十八禁人妻一区二区| 黄色毛片三级朝国网站| 国产av一区二区精品久久| 嫁个100分男人电影在线观看| 国产精品免费大片| 欧美乱码精品一区二区三区| 999久久久精品免费观看国产| 亚洲国产看品久久| 18禁裸乳无遮挡免费网站照片 | 黄色女人牲交| 两人在一起打扑克的视频| av免费在线观看网站| 天堂√8在线中文| 久久九九热精品免费| 美女扒开内裤让男人捅视频| 国产激情欧美一区二区| 成年人午夜在线观看视频| 午夜影院日韩av| 色精品久久人妻99蜜桃| 亚洲一区二区三区不卡视频| 亚洲久久久国产精品| 女人精品久久久久毛片| 黄色 视频免费看| 免费观看人在逋| 中文字幕最新亚洲高清| 在线观看www视频免费| 精品一品国产午夜福利视频| 午夜福利在线免费观看网站| 亚洲人成电影观看| 最新美女视频免费是黄的| 国产欧美日韩一区二区三区在线| 在线观看午夜福利视频| 欧美国产精品va在线观看不卡| 美女高潮喷水抽搐中文字幕| 久久精品国产99精品国产亚洲性色 | 一区福利在线观看| 露出奶头的视频| 亚洲一码二码三码区别大吗| 国产麻豆69| 18禁裸乳无遮挡动漫免费视频| 中文字幕av电影在线播放| 国产真人三级小视频在线观看| 大香蕉久久成人网| 成年人午夜在线观看视频| 18禁国产床啪视频网站| 男女下面插进去视频免费观看| 一区在线观看完整版| 成人手机av| 亚洲欧洲精品一区二区精品久久久| 又黄又爽又免费观看的视频| 在线天堂中文资源库| 成人三级做爰电影| 国产日韩欧美亚洲二区| 桃红色精品国产亚洲av| 午夜福利影视在线免费观看| 啦啦啦免费观看视频1| 国产精品av久久久久免费| 别揉我奶头~嗯~啊~动态视频| 正在播放国产对白刺激| 亚洲中文字幕日韩| 亚洲av电影在线进入| 正在播放国产对白刺激| 啦啦啦免费观看视频1| 亚洲一卡2卡3卡4卡5卡精品中文| 女同久久另类99精品国产91| 亚洲精品中文字幕一二三四区| 精品少妇久久久久久888优播| 国产亚洲精品第一综合不卡| 亚洲av熟女| 女人被狂操c到高潮| 91精品国产国语对白视频| 在线观看66精品国产| 亚洲,欧美精品.| 两性夫妻黄色片| 久久精品亚洲精品国产色婷小说| www.999成人在线观看| 人妻久久中文字幕网| 女人被躁到高潮嗷嗷叫费观| 99riav亚洲国产免费| 高清在线国产一区| 国产精品久久久久成人av| 人人妻,人人澡人人爽秒播| av有码第一页| 午夜成年电影在线免费观看| 日韩成人在线观看一区二区三区| 女警被强在线播放| 一级黄色大片毛片| 交换朋友夫妻互换小说| 99国产精品99久久久久| 99在线人妻在线中文字幕 | 亚洲第一青青草原| 欧美日韩视频精品一区| 精品第一国产精品| 亚洲五月色婷婷综合| avwww免费| 中国美女看黄片| av电影中文网址| 天堂√8在线中文| 多毛熟女@视频| 91成人精品电影| 99精品久久久久人妻精品| 国产乱人伦免费视频| 国产精品一区二区在线观看99| 两个人看的免费小视频| 成人国产一区最新在线观看| 亚洲av日韩精品久久久久久密| 99精品久久久久人妻精品| 国产高清国产精品国产三级| 亚洲中文字幕日韩| 最近最新免费中文字幕在线| 色婷婷久久久亚洲欧美| 性色av乱码一区二区三区2| 日日爽夜夜爽网站| 国产欧美日韩精品亚洲av| 亚洲国产中文字幕在线视频| 美女午夜性视频免费| 热99re8久久精品国产| 亚洲熟女毛片儿| 国产三级黄色录像| 国产国语露脸激情在线看| 啦啦啦视频在线资源免费观看| 天天躁夜夜躁狠狠躁躁| 一区二区三区精品91| 曰老女人黄片| 大型av网站在线播放| 午夜91福利影院| 日本黄色日本黄色录像| 黑人欧美特级aaaaaa片| ponron亚洲| 女人久久www免费人成看片| 操出白浆在线播放| 日日夜夜操网爽| 欧美+亚洲+日韩+国产| 嫁个100分男人电影在线观看| 亚洲一区中文字幕在线| 亚洲国产精品一区二区三区在线| netflix在线观看网站| 日韩三级视频一区二区三区| 精品国内亚洲2022精品成人 | 成人国语在线视频| 好男人电影高清在线观看| 国产伦人伦偷精品视频| 大码成人一级视频| 亚洲午夜精品一区,二区,三区| 一区福利在线观看| 男人操女人黄网站| 九色亚洲精品在线播放| av超薄肉色丝袜交足视频| 欧美人与性动交α欧美软件| 午夜福利在线免费观看网站| 亚洲国产欧美网| 国产精品九九99| 人人妻人人添人人爽欧美一区卜| 欧美黑人欧美精品刺激| 午夜免费鲁丝| 国产精品香港三级国产av潘金莲| 又大又爽又粗| 人人妻人人添人人爽欧美一区卜| 国产高清视频在线播放一区| 五月开心婷婷网| 99久久综合精品五月天人人| 亚洲少妇的诱惑av| e午夜精品久久久久久久| 大型黄色视频在线免费观看| 欧美色视频一区免费| 午夜两性在线视频| 这个男人来自地球电影免费观看| 国产精品亚洲一级av第二区| 嫁个100分男人电影在线观看| 久热爱精品视频在线9| 女人久久www免费人成看片| 久久草成人影院| 精品少妇一区二区三区视频日本电影| 宅男免费午夜| av福利片在线| 一级a爱视频在线免费观看| а√天堂www在线а√下载 | 久久精品成人免费网站| 亚洲精品成人av观看孕妇| 国产成人精品无人区| 欧美性长视频在线观看| 大型av网站在线播放| 老司机亚洲免费影院| 国内毛片毛片毛片毛片毛片| 脱女人内裤的视频| 男女午夜视频在线观看| 黄频高清免费视频| 国产精品 欧美亚洲| 999精品在线视频| 狠狠婷婷综合久久久久久88av| 一区二区三区国产精品乱码| 久久精品人人爽人人爽视色| 韩国av一区二区三区四区| 日韩视频一区二区在线观看| 久久精品亚洲精品国产色婷小说| 日韩欧美免费精品| 757午夜福利合集在线观看| а√天堂www在线а√下载 | 久久香蕉激情| 国产精品国产高清国产av | 黄色丝袜av网址大全| 欧美日韩黄片免| 亚洲国产精品一区二区三区在线| 50天的宝宝边吃奶边哭怎么回事| 亚洲第一青青草原| 亚洲精品久久午夜乱码| 女性生殖器流出的白浆| 亚洲国产欧美网| 国产男女超爽视频在线观看| 久久精品亚洲精品国产色婷小说| 久久99一区二区三区| 亚洲中文日韩欧美视频| 亚洲片人在线观看| 欧美人与性动交α欧美精品济南到| netflix在线观看网站| 亚洲精品久久成人aⅴ小说| 国产熟女午夜一区二区三区| 身体一侧抽搐| 人人妻人人澡人人看| 丝瓜视频免费看黄片| 国产麻豆69| 女人高潮潮喷娇喘18禁视频| 久久久久国产一级毛片高清牌| 国产xxxxx性猛交| 大片电影免费在线观看免费| 国产精品国产av在线观看| 黑人猛操日本美女一级片| 日韩欧美国产一区二区入口| 国产精品久久久久久人妻精品电影| av天堂久久9| 91字幕亚洲| 亚洲一区二区三区欧美精品| 王馨瑶露胸无遮挡在线观看| 国产免费现黄频在线看| 天天躁日日躁夜夜躁夜夜| 免费观看人在逋| 欧美精品啪啪一区二区三区| 老鸭窝网址在线观看| 亚洲五月色婷婷综合| 久久精品亚洲av国产电影网| 午夜精品国产一区二区电影| 99热网站在线观看| 亚洲国产看品久久| aaaaa片日本免费| 热re99久久精品国产66热6| 精品国产一区二区三区久久久樱花| 久久中文字幕一级| 人人妻人人添人人爽欧美一区卜| 精品国产美女av久久久久小说| 中文字幕最新亚洲高清| 亚洲熟妇熟女久久| 欧美日韩国产mv在线观看视频| 亚洲九九香蕉| 亚洲色图av天堂| a在线观看视频网站| 在线观看www视频免费| 99精品久久久久人妻精品| 国产深夜福利视频在线观看| 国产成人免费观看mmmm| 老司机靠b影院| 亚洲aⅴ乱码一区二区在线播放 | 亚洲成国产人片在线观看| 国产成人系列免费观看| 久久久久精品国产欧美久久久| 在线永久观看黄色视频| 免费在线观看日本一区| 精品国产一区二区三区久久久樱花| 欧美 亚洲 国产 日韩一| 久久亚洲真实| 欧美亚洲日本最大视频资源| 日本vs欧美在线观看视频| 十八禁高潮呻吟视频| 99精品久久久久人妻精品| 侵犯人妻中文字幕一二三四区| 人人妻人人澡人人爽人人夜夜| 色尼玛亚洲综合影院| videosex国产| 人妻久久中文字幕网| 妹子高潮喷水视频| 亚洲国产精品一区二区三区在线| 黄色毛片三级朝国网站| a级片在线免费高清观看视频| 高清在线国产一区| 成年人免费黄色播放视频| 99久久99久久久精品蜜桃| 亚洲精品中文字幕一二三四区| 亚洲欧美精品综合一区二区三区| 国产欧美日韩一区二区精品| 国产野战对白在线观看| 首页视频小说图片口味搜索| 欧美亚洲日本最大视频资源| 丝袜美腿诱惑在线| xxxhd国产人妻xxx| 日韩精品免费视频一区二区三区| 日本vs欧美在线观看视频| 男人舔女人的私密视频| 欧美日韩乱码在线| 日韩熟女老妇一区二区性免费视频| 国产亚洲欧美精品永久| 精品亚洲成国产av| 国产熟女午夜一区二区三区| 飞空精品影院首页| 国产成人欧美在线观看 | 麻豆av在线久日| 成年人午夜在线观看视频| 久久人妻福利社区极品人妻图片| av免费在线观看网站| 亚洲熟女精品中文字幕| 午夜福利视频在线观看免费| 中文字幕最新亚洲高清| 露出奶头的视频| 美女国产高潮福利片在线看| 亚洲七黄色美女视频| 一本大道久久a久久精品| 女性生殖器流出的白浆| 成人18禁在线播放| 久热这里只有精品99| 高清av免费在线| 欧美黄色片欧美黄色片| 色播在线永久视频| 久久久久久久久久久久大奶| 一进一出抽搐gif免费好疼 | 国产免费男女视频| 亚洲人成电影观看| 亚洲少妇的诱惑av| 亚洲欧洲精品一区二区精品久久久| 亚洲男人天堂网一区| 在线播放国产精品三级| 欧美黑人精品巨大| 两人在一起打扑克的视频| 亚洲专区国产一区二区| 十八禁网站免费在线| 99久久精品国产亚洲精品| 亚洲精品国产区一区二| 午夜精品在线福利| 精品亚洲成国产av| 久久人妻av系列| 免费高清在线观看日韩| 侵犯人妻中文字幕一二三四区| 国产极品粉嫩免费观看在线| 国产不卡一卡二| 怎么达到女性高潮| 久久精品国产亚洲av高清一级| 在线观看www视频免费| 国产亚洲欧美98| 国产精品国产av在线观看| 一级毛片高清免费大全| a级毛片在线看网站| 999久久久国产精品视频| 大片电影免费在线观看免费| 久久久水蜜桃国产精品网| 国产精品乱码一区二三区的特点 | 亚洲av熟女| 久久婷婷成人综合色麻豆| 久久精品国产99精品国产亚洲性色 | 国产欧美日韩综合在线一区二区| 99re在线观看精品视频| 窝窝影院91人妻| 51午夜福利影视在线观看| 妹子高潮喷水视频| 欧美一级毛片孕妇| 91精品三级在线观看| 老司机深夜福利视频在线观看| 欧美亚洲 丝袜 人妻 在线| 亚洲少妇的诱惑av| 久久热在线av| 黄频高清免费视频| 丝袜在线中文字幕| 亚洲avbb在线观看| 岛国毛片在线播放| 精品福利观看| x7x7x7水蜜桃| 18禁国产床啪视频网站| 午夜福利影视在线免费观看| 青草久久国产| 一级a爱片免费观看的视频| 黄色怎么调成土黄色| 亚洲av日韩在线播放| 麻豆乱淫一区二区| 欧美色视频一区免费| 午夜精品国产一区二区电影| 精品无人区乱码1区二区| 色在线成人网| 久久草成人影院| 天天躁狠狠躁夜夜躁狠狠躁| 国产97色在线日韩免费| 久久国产精品男人的天堂亚洲| 午夜久久久在线观看| 日韩欧美三级三区| 老司机深夜福利视频在线观看| 如日韩欧美国产精品一区二区三区| 自线自在国产av| 夜夜夜夜夜久久久久| 巨乳人妻的诱惑在线观看| 欧美成人免费av一区二区三区 | 免费观看人在逋| 色老头精品视频在线观看| 又大又爽又粗| 色在线成人网| 怎么达到女性高潮| 精品福利永久在线观看| 日韩欧美国产一区二区入口| 国产aⅴ精品一区二区三区波| 精品国产乱码久久久久久男人| 亚洲欧美一区二区三区久久| 久久久久国内视频| 天天躁狠狠躁夜夜躁狠狠躁| 欧美最黄视频在线播放免费 | 在线观看免费日韩欧美大片| 少妇粗大呻吟视频| 亚洲人成伊人成综合网2020| 日本五十路高清| 可以免费在线观看a视频的电影网站| 波多野结衣av一区二区av| 狂野欧美激情性xxxx| 精品人妻在线不人妻| 黑人欧美特级aaaaaa片| 狠狠婷婷综合久久久久久88av| 老司机靠b影院| 欧洲精品卡2卡3卡4卡5卡区| 午夜福利在线免费观看网站| 在线观看www视频免费| av网站在线播放免费| 人人妻人人澡人人爽人人夜夜| 亚洲中文字幕日韩| 老司机福利观看| 国产成人精品在线电影| 亚洲精品在线美女| 亚洲avbb在线观看| 日韩视频一区二区在线观看| 久热爱精品视频在线9| 一级作爱视频免费观看| 久久久国产欧美日韩av| 国产高清videossex| 国产欧美日韩精品亚洲av| 一级毛片高清免费大全| 丝袜美腿诱惑在线| 久久久久国产精品人妻aⅴ院 | 侵犯人妻中文字幕一二三四区| 别揉我奶头~嗯~啊~动态视频| av中文乱码字幕在线| 精品国产乱子伦一区二区三区| 夜夜爽天天搞| 精品亚洲成国产av| 国产在线精品亚洲第一网站| 国产男女超爽视频在线观看| 色老头精品视频在线观看| 男人的好看免费观看在线视频 | 亚洲在线自拍视频| 国产亚洲精品久久久久5区| 18禁观看日本| xxx96com|