• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Microstructure,texture evolution and yield strength symmetry improvement of as-extruded ZK60 Mg alloy via multi-directional impact forging

    2022-12-26 02:35:30ChoCuiWencongZhngWenzhenChenJinHeXueminChenJibinHou
    Journal of Magnesium and Alloys 2022年10期

    Cho Cui,Wencong Zhng,b,c,Wenzhen Chen,b,c,?,Jin He,Xuemin Chen,Jibin Hou

    a School of Materials Science and Engineering,Harbin Institute of Technology,Weihai 264209,China

    b Weihai Lightweight Materials and Forming Engineering Research Center,Weihai 264209,China

    c Harbin Institute of Technology-Weihai Innovation Park,Weihai 264209,China

    Abstract Multi-direction impact forging(MDIF)was applied to the as-extruded ZK60 Mg alloy,and the microstructure,texture evolution and yield strength symmetry were investigated in the current study.The results showed that the average grain size of forged piece was greatly refined to 5.3μm after 120 forging passes,which was ascribed to the segmenting effect of{10–12}twins and the subsequent multiple rounds of dynamic recrystallization(DRX).A great deal of{10–12}twins were activated at the beginning of MDIF process,which played an important role in grain refinement.With forging proceeding,continuous and discontinuous DRX were successively activated,resulting in the fully DRXed microstructure.Meanwhile,the forged piece exhibited a unique four-peak texture,and the initial<10-10>//ED fiber texture component gradually evolved into multiple texture components composed of<0001>//FFD(first forging direction)and<11–20>//FFD texture.The special strain path was the key to the formation of the unique four-peak texture.The{10–12}twinning and basal slip were two dominant factors to the evolution of texture during MDIF process.Grain strengthening and dislocation strengthening were two main strengthening mechanisms of the forged piece.Besides,the symmetry of yield strength was greatly improved by MDIF process.

    Keywords:Multi-directional impact forging;Twinning;Dynamic recrystallization;Texture;Yield strength symmetry.

    1.Introduction

    Magnesium(Mg)alloys possess certain extraordinary physical properties,such as low density,high specific strength and high specific stiffness,and therefore are becoming increasingly attractive for potential use in the automotive,aerospace and communicated industries[1,2].However,Mg has a hexagonal closed-pack(hcp)crystal structure with an insufficient number of operative slip systems,leading to limited ductility at room temperature.In addition,the formation of strong basal texture during hot working process will bring about the severe asymmetry in yield strength[3–13],including tension/compression yield strength asymmetry(Table 1)and tension yield strength anisotropy(Table 2).These defects limit the widespread industrial applications of Mg alloys.

    Table 1Literature review of the tension/compression yield strength asymmetry in Mg alloys fabricated by different hot working processes.

    Table 2Literature review of the tension yield strength anisotropy in Mg alloys fabricated by different hot working processes(LD:longitudinal direction;TD:transverse direction).

    Grain refinement and texture modification are considered as two effective ways to improve the mechanical properties of Mg alloys.Recently,some severe plastic deformation(SPD)techniques,such as friction stir processing(FSP)[14],different speed rolling(DSR)[15],high-pressure torsion(HPT)[16],multi-directional forging(MDF)[17,18],etc.,were used to improve strength and ductility of Mg alloys by grain refinement and texture modification.Among these SPD methods,MDF has the advantages of simple operation,low cost,and suitable for large-scale industrial products.Moreover,MDF has greater potential for weakening the basal texture of thewrought Mg alloy due to the continuously changing external load direction on the workpiece.In previous research,MDF has been applied to different Mg alloys to obtain finegrained microstructure and excellent mechanical properties.Miura et al.[19]fabricated an ultra-fine grains AZ61 Mg alloy with the average grain size of 0.8μm by MDF under decreasing temperature conditions,and the MDFed AZ61 Mg alloy exhibited a superior balance of strength and ductility,with ultimate tensile strength(UTS)of 440MPa and plastic strain to fracture of over 20%.Wu et al.[20]reported that high strain rate multiple forging(HSRMF)was successfully carried out on ZK60 Mg alloy.The initial grains were extensively refined after HSRMF due to dynamic recrystallisation(DRX)and the elongation as well as ultimate tensile strength was significantly improved.Shah et al.[21]studied the effect of multi-direction impact forging(MDIF)on solutionized Mg-Gd-Y-Zr alloy.They reported that the initial coarse grains of Mg-Gd-Y-Zr alloy were significantly refined from 165μm to 5μm after 50 forging passes,and both strength and ductility of GW94 alloy were enhanced by the MDIF process.From the above,these previous researches have shown that MDF can significantly refine grains,often attributed to DRX process,and improve mechanical properties for both traditional commercial Mg alloy and new rare earth(RE)Mg alloy.However,the effect of various DRX mechanisms on the crystallographic orientation evolution was not clear.Also,the enhanced mechanical properties were often attributed to the grain refinement,whereas texture effect was not taken into consideration.Moreover,the effect of MDF on yield strength asymmetry of Mg alloys has not been reported so far.

    In this work,a multi-directional impact forging(MDIF)technology was applied to the as-extruded ZK60 Mg alloy and a small pass strain of about 0.05 was employed.The small pass strain was designed to avoid the formation of strong compressed type basal texture.Different from the conventional MDF performed on the hydraulic press machine,MDIF used industrial air pneumatic hammer machine for high strain rate forging,which could effectively improve forging efficiency and reduce processing costs.From MDIF technology,the yield strength asymmetry of as-extruded ZK60 Mg alloy has been significantly improved due to the grain refinement and texture modification.The evolution of microstructure and texture during MDF process will be discussed in detail in this paper,as well as the effect of various DRX mechanisms on the crystallographic orientation evolution.It is hoped that this paper will provide useful information for manufacturing large block ZK60 Mg alloy with yield strength symmetry and expanding the application range of Mg alloy in a simpler process.

    2.Experimental procedures

    A commercial ZK60 Mg alloy(Mg-6.63 wt%Zn-0.56 wt%Zr)was used in this work.Cubic block samples were machined from the as-extruded ZK60 Mg bar stock with dimensions of 60×60×60mm3.The cubic block samples were firstly heated to 400°C in an electric resistance furnace and kept for 30min.Then,the MDIF process was performed using industrial air pneumatic hammer machine with load gravity of 150 Kg.To avoid a rapid drop in the sample temperature during MDIF process,the top and bottom anvils contacting the sample were also heated to 400°C before forging.As shown in Fig.1a,the initial forging direction is parallel to the extrusion direction,and between the continuously forging passes,the loading direction was changed by 90° pass by pass(i.e.,X to Y to Z to X···)and no reheating process was carried out during the whole MDIF process.In order to study the microstructural evolution during MDIF process,the samples were forged to different forging passes(1,3,6,12,30,60,120 passes)which were named MDIF1,MDIF3,MDIF6,MDIF12,MDIF30,MDIF60,and MDIF120,respectively.After MDIF process,the surface temperature of each forged piece was detected by a TES 1310 Type-K thermometer and listed in Table 3,and then these forgings were quickly cooled down in water.As shown in Fig.1b,the forged piece with 120 passes was free from any surface defects.

    Table 3The final surface temperatures of each samples.

    As shown in Fig.1c,the microstructures were observed at the central part of the FFD-LFD plane(FFD:the first forging direction,LFD:the last forging direction)using electron back-scatter diffraction(EBSD)and scanning electron microscopy(SEM).Sample was prepared for EBSD observation by mechanical grinding with 3000-grit SiC paper,followed by electro-chemical polishing in a 5:3 solution of ethanol and phosphoric acid for 8min at 0.25 A.EBSD was carried out at 20kV,15mm working distance,a tilt angle of 70° and ascan step of 0.5μm.The scans results were analyzed using TSL OIM Analysis 7.2.1 software.For SEM observation,the samples were polished and etched with a solution of 4.0g picric acid,50ml alcohol,20ml acetic acid and 20ml distilled water.The tensile specimens(17.5mm in gage length and 3mm in diameter of gage section)and compressive specimens(7.5mm in length and 5mm in diameter)were extracted from the central part of FFD-LFD plane,as shown in Fig.1c.Tension and compression properties at room temperature were tested by Instron 5967 testing machine with an initial strain rate of 1×10-3s-1.

    Fig.1.(a)Schematic illustrations of the MDIF process,(b)macroscopic morphology of forged piece after MDIF120 passes and(c)the position of microstructure,tension and compression specimens in the forged pieces.

    3.Results and discussion

    3.1.Microstructure characteristics of the as-extruded ZK60 mg alloy

    Fig.2a shows the microstructure characteristics of the asextruded ZK60 Mg alloy in the inverse pole figure map on ED-TD plane(ED:extrusion direction,TD:transverse direction).It was clear that the initial material had a bimodal grain size,consisting of small DRXed grains and large deformed grains elongated along the extrusion direction.The average grain size of small equiaxed grains(<40μm)was about 18.6μm(Fig.2b),while the grain size of some large deformed grains could not be accurately measured from the present EBSD.As shown in Fig.2c and d,the initial material exhibits a strong(0002)basal texture with maximal pole intensity of 9.60 existing typical<10-10>//ED fiber texture component[22].As shown in Fig.2e,low angle grain boundaries(LAGBs,2–15°)and high angle grain boundaries(HAGBs,15–100°)accounting for 31.9% and 68.1% respectively,and these LAGBs were concentrated in the coarse deformed grains(Fig.2a).

    3.2.Microstructure evolution during MDIF process

    In order to analyze the evolution of microstructure during MDIF process,the MDIFed pieces with different forging passes were examined in detail using EBSD and the corresponding results are presented in Figs.3-9,respectively.LAGBs,HAGBs and twin boundaries of different types including{10–12}extension,{10–11}contraction and{10–11}-{10–12}double twin boundaries were highlighted withdifferent colors.The angular deviation to identify the twin boundaries was within 5° of the ideal values.

    Fig.2.EBSD observation results of the as-extruded ZK60 Mg alloy:(a)inverse pole figure map,(b)distribution histogram of grain size,(c)(0002)basal pole figure,(d)inverse pole figure and(e)distribution histogram of misorientation angle.

    Fig.3 shows EBSD observation results of the ZK60 alloy after the first forging pass.As shown in the inverse pole figure map(Fig.3a),plenty of twins were activated in initial coarse grains,and dividing them into many irregular grains by these twins.According to the corresponding boundary misorientation map(Fig.3b),all of these twins were identified to be{10–12}twins.Besides,it can be clearly found that these{10–12}twins had different morphologies and paralleled or intersected to each other(Fig.3a),which was related to the activation of various twin variants.The distribution histogram of misorientation angle(Fig.3c)displays three obvious peaks for LAGBs,as well as HAGBs close to 60° and 86° From the corresponding axis distributions inserted in Fig.3c,it could be seen that the distinct peak at 86°±5° shared a strong〈11–20〉rotation axis,which corresponded well to{10–12}twins.However,the peak at 60°±5° shared a strong〈10–10〉rotation axis.In Mg alloys,different misorientation relationships can be generated between different{10–12}twin variants:7.4° about〈11–20〉axis between the same twin variant pair and 60° about〈10–10〉axis between different twin variant pairs[23,24].Hence,the distinct peaks close to 60° were mainly ascribed to the intersection of different twin variant pairs.In order to clarify the effect of{10–12}twins on the texture evolution at the early stage of the MDIF process,the crystallographic orientation of{10–12}twins were separately highlighted in blue as shown in Fig.3e and f.It could be found that most of the{10–12}twins displayed the basal planes perpendicular to the FFD and exhibited<0001>‖F(xiàn)FD crystallographic orientation.Fig.3d shows the distribution of grain size after the first forging pass,and the average grain size was reduced to 23.5μm due to the segmenting effect of twins on the initial coarse grains.

    In order to specifically demonstrate{10–12}twinning behavior after the first forging pass,the typical initial coarse grains(G1-G4)containing twins with different morphologies were extracted from Fig.3a.Besides,to distinguish the twin variants activated in G1-G4,six possible variants of each{10–12}twin are coded as T1-T6 in advance and the relative geometrical relationships of the six variants are reflected in the schematic diagram(Table 4).In the following sections,the analysis of the selection mechanism for various twin variants would use such code.

    Table 4The codes and indices of six possible{10–12}twin variants and the illustration of their geometrical relationships.

    Fig.3.EBSD observation results of the ZK60 Mg alloy after the first forging pass:(a)inverse pole figure map,(b)corresponding boundary misorientation map,(c)distribution histogram of misorientation angle with axis distributions for the angles of 60°±5° and 86°±5°,(d)distribution histogram of grain size,(e)(0002)pole figure and(f)inverse pole figure.

    The various twin variants activated in G1-G3 were clearly identified based on the particular misorientation angles and rotation axes,including 86.3±5° about〈11–20〉axis between{10–12}twin and its parent grain,7.4±5°about〈11–20〉axis between a twin variant pair and 60±5° about〈10–10〉axis between two different twin variant pairs.Table 5 gives the misorientation angles of points at the junction of twins with different morphologies indicated in Fig.4a,e,and i.Besides,the orientation of parent grains(blue square)in G1-G3 andcorresponding six possible{10–12}twin variants(red circles)were marked in a(0002)pole figure(Fig.4b,f and j).Interestingly,the activation of twin variants in grain G1-G3 was identical,i.e.,two pairs twin variant T1,T4 and T3,T6 were activated.The crystallographic orientation relationship between parent grains and various twin variants was shown in(0002)pole figure(Fig.4b,f and j)and corresponding inverse pole figure(Fig.4c,g and k).In G1,the parent grain belonged to[11–20]fiber orientation with a slight deviation of~12° from[11–20]//FFD,and the orientation of all twin variants was between[0001]//FFD and[11–24]//FFD.In G2,the orientation of parent grain had a slight deviation from[11–21]//FFD,while the orientation of all twin variants was between[0001]//FFD and[10–12]//FFD.The crystallographic orientation of both parent grain and twin variants in G3 was very similar to those in G1.Fig.4d,h and l clearly depict the three-dimensional crystallographic relationship between parent grains and various variants in G1-G3.

    Table 5The misorientation angles of points at the junction of twins with different morphologies indicated in Fig.4a,e,and i.

    Table 6Schmid factor values of six{10–12}twin variants and their activations in the four grains(G1-G4)of MDIF1 sample.

    Fig.4.The details of{10–12}twinning behavior after the first forging pass in the initial coarse grains(a-d)G1,(e-h)G2 and(i-l)G3 selected in Fig.3a:(a,e,i)inverse pole figure maps,(b,f,j)(0002)pole figure,(c,g,k)inverse pole figure and(d,h,l)three-dimensional crystallographic relationship between various variants and their parent grain.(P:parent grain,T:various variants).Blue squares and red circles indicating parent grains and six potential twin variants,respectively.(For interpretation of the references to colour in this figure legend,the reader is referred to the web version of this article.)

    Clearly,the initial coarse grain G4 shown in Fig.3a has obviously different microstructure characteristics compared to the above grains G1~G3,i.e.,parent grain was almost swallowed by{10–12}twins and some fine DRXed grains were observed in G4.To study the effect of{10–12}twins on the subsequent DRX process,the initial coarse grain G4 was extracted from Fig.3a.The various variants activated in G4 was identified in the same way,and the results showed that two different{10–12}twin variants T2 and T5 were activated in G4.As shown in corresponding(0002)pole figure(Fig.5b)and inverse pole figure(Fig.5c),the parent grain had a[10–10]fiber orientation,while these two variants T2 and T5 exhibited[0001]//FFD crystallographic orientation.Meanwhile,according to the location of DRXed grains and the color shown in the inverse pole figure maps(Fig.5a),these DRXed grains could be roughly divided into two categories:(i)concentrated in the interior and boundary of twins and had a blue or purple color;(ii)scattered in the parent grain and possessed a red or orange color,and the above two kinds of DRXed grains were named TDRX grains and PDRX grains,respectively.From the corresponding(0002)pole figure(Fig.5d)and inverse pole figure(Fig.5e),it could be found that TDRX grains showed obvious preference orientation,which was very close to T2 and T5;although the orientation distribution of PDRX grains was more diffuse,it also showed obvious preference orientation.The orientation distributions of DRXed grains were quantified by the spread angle away from the[0001]direction in inverse pole figures.Clearly,the spread angles of TDRX grains and PDRX grains were 0–35° and 72–90°,respectively.The misorientation angles developed along the red arrow AB in{10–12}twins showed that the point-to-origin misorientation gradually increased up to 25°(Fig.5f),indicating the high activity of dislocations in{10–12}twins.A previous study[25]reported that the highly incoherent twin boundaries have a strong obstacle effect on the dislocations and contribute significantly to the DRX behavior and formation of DRX chains inside the grain.Therefore,we can infer that{10–12}twins facilitated the subsequent DRX process and formed the above TDRX grains.Besides,a continuous increase misorientation angles along the red arrow CD in parent grain were observed(Fig.5g),which indicated the dislocation slip inthe parent grain was also active.Hence,it could be speculated that while the{10–12}twins continued to expand and swallow the parent grain,DRX process was taking place in part of parent grain,so as to generate the above PDRX grains.

    Fig.5.The effect of{10–12}twins on the subsequent DRX process:(a)inverse pole figure maps,(b,d)(0002)pole figure,(c,e)inverse pole figure and(f,g)the misorientation angles developed along the red arrows AB and CD indicated in(a).Blue square and red circles indicating parent grains and six potential twin variants,respectively.(For interpretation of the references to colour in this figure legend,the reader is referred to the web version of this article.)

    Generally,the selection mechanism for various{10–12}twin variants strongly depends on the strain path,i.e.,compression perpendicular to the c-axis or tension parallel to the c-axis[26].Hong et al.[27]suggested that all six twin variants were equally possible to be activated due to the same Schmid factor when tension parallel to the c-axis,while for compression perpendicular to the c-axis,the twin variants with higher Schmid factor were activated preferentially.Therefore,we analyzed the selection mechanism for various{10–12}twin variants using the Schmid law in this work.The Schmid factor of six possible{10–12}twin variants in G1-G4 were calculated and displayed at the Table 6.Those bold black fonts highlighted in Table 6 corresponded to the activated twin variants.We could see that the twin variants with the Schmid factor ranking in top four were activated in G1-G3,and the T2 and T5 with the Schmid factor significantly higher than other twin variants were activated in G4.Obviously,the selection mechanism of various twin variants is governed by the Schmid law during the MDIF process of ZK60 Mg alloy.In addition,it could be found that the morphology and growth mechanism of{10–12}twins also seem to be related to the Schmid factor.The twin variants with relatively low Schmid factor in G2 showed a typical lenticular morphology and these twins did not grow further(Fig.4e),while the T2 and T5 in G4 with the highest Schmid factor obviously grew up and the parent grain was almost swallowed by these twins(Fig.5a).Therefore,we can infer that the Schmid factor of{10–12}twins is positively correlated with its growth rate.

    Fig.6 shows EBSD observation results of the ZK60 alloy after 3,6 and 12 forging passes.The inverse pole figure maps(Fig.6a,d and g)show an inhomogeneous microstructure,consisting of equiaxed DRXed grains and irregular grains.Through careful observation,it could be found that a large number of LAGBs were mainly concentrated in these irregular grains,as shown in R1,R2 and R3 in Fig.6a,d and g.According to relevant literature[28,29],the existence of abundant LAGBs is a typical feature of continuous dynamic recrystallization(CDRX).Therefore,it can be speculated that the grain refining mechanism was dominated by CDRX process in this period.In the corresponding boundary misorientation maps(Fig.6b,e and h),all the twins were still found to be{10–12}twins.Besides,the fraction of{10–12}twins were gradually reduced with the increase of forgingpasses.Fig.6c,f and i show the distribution of grain size after forging 3,6,and 12 passes respectively,the average grain size did not change significantly due to the small cumulative strain during this period.

    Fig.6.EBSD observation results of the ZK60 Mg alloy after 3(a-c),6(d-f)and 12(g-i)forging pass:(a,d,g)inverse pole figure map,(b,e,h)corresponding boundary misorientation map and(c,f,i)distribution histogram of grain size.

    Fig.7 shows the details of CDRX behavior and corresponding effect on the crystallographic orientation evolution in R1-R3 selected in Fig.6a,d and g,respectively.As shown in Fig.7a,e and i,there are several similarities as follows.First,lots of LAGBs was observed in parent grains.Second,sub-grains formed subdividing these parent grains into several parts.Third,fine DRXed grains formed surrounding parent grains boundaries or situated inside parent grains.Fig.7d,h and l respectively show the misorientation angles developed along the blue arrows AB,CD and EF indicated in(a,e,i).It can be found that there is a large orientation gradient in parent grains,which suggests the high activity of dislocations in the parent grains.Previous literatures[30,31]had shown that the accumulated dislocations on dislocation walls would rearrange or merge with each other to generate sub-grains,and eventually formed new DRXed grains by continuous absorption of the dislocations in sub-GBs.The corresponding(0002)pole figure(Fig.7b,f and j)and inverse pole figure(Fig.7c,g and k)exhibit the crystallographic orientation of parent grains,parts of sub-grains and DRXed grains.We could see that the orientation of the sub-grains was very close to that of the parent grains,while the orientation distribution of the DRXed grains was more diffused,but it also showed a clearly preferred orientation related to the parent grains.

    Fig.8 shows EBSD observation results of the ZK60 Mg alloy after 30,60 and 120 forging passes.As shown in the inverse pole figure maps(Fig.8a,d and g),the irregular grains almost disappeared and the microstructure became much more homogeneous.Compared to the previous period,although the fraction of LAGBs was significantly reduced,it was still at a higher level.A careful examination on Fig.8a and d shows that these LAGBs were mainly concentrated in the relatively large DRXed grains,indicating that CDRX was still the dominant mechanism for grain refinement in this period.And the relatively large DRXed grains were further refined by a new round of CDRX process.However,it should be noted thatCDRX was not the only grain refinement mechanism during MDIF process.As shown in R4 and R5 in Fig.8a and d,some small grains(<5μm)formed along the serrated grain boundaries of relatively large DRXed grains,which was a discontinuous dynamic recrystallization(DDRX)process with nucleation at serrated HAGBs by bulging and grain growth by grain boundaries migration[32,33].The corresponding boundary misorientation maps(Fig.8b,e and h)shows that the microstructure was almost twin-free.In the distribution histogram of grain size(Fig.8c,f and i),the average grain size was effectively refined with the continuous increase of cumulative strain.Especially after 120 forging passes,the average grain size was refined to 5.3μm.It should be pointed out that after 120 forging passes,the significant refinement of grain size was unnegligiblely influenced by the temperature,in addition to the contribution of high cumulative strain.Generally,the DRXed grain size largely depends on the Zener-Hollomon parameter Z(Z=˙εexp(Q/RT)),where˙εis the strain rate,Qis the activation energy,Ris the gas constant andTis the deformation temperature,and a finer DRXed grain size will be obtained by increasing the Z-parameter[34,35].

    Fig.7.The details of CDRX behavior and corresponding effect on the crystallographic orientation evolution in R1(a-d),R2(e-h)and R3(i-l)selected in Fig.6a,d and g,respectively:(a,e,i)inverse pole figure maps,(b,f,j)(0002)pole figure,(c,g,k)inverse pole figure and(d,h,l)the misorientation angles developed along the blue arrows AB,CD and EF indicated in(a,e,i).(For interpretation of the references to colour in this figure legend,the reader is referred to the web version of this article.)

    Fig.9 shows the details of DDRX behavior and corresponding effect on the crystallographic orientation evolution in R4 and R5.Compared to the previous CDRX,the formation of new DRXed grains by DDRX process had a distinct characteristic,i.e.,the DRXed grains nucleated along serrated HAGBs of parent grains by bulging.Sitdikov et al.[36]suggested that the interaction between non-basal slip and basal slip dislocations yields the formation of sub-GBs,which cut off the protrusion from the grain body,and the misorientation of such sub-GBs increase with increasing strain by continuous gathering dislocations,finally leading to the formation of new DRXed grains.It is well known that non-basal slip system is difficult to be operated at room temperature due to the high critical resolved shear stress(CRSS).However,the CRSS for non-basal slip system significantly decreases as the temperature increases[37].Besides,non-basal slip system becomes easier to be activated with the decrease of grain size due to grain-boundary compatibility stress[38,39].Therefore,the combined effect of grain refinement and high temperature makes non-basal slip systems active,which contributes to the DDRX process.The crystallographic orientation relationship between parent grains and DRXed grains in R4 and R5 is shown in Fig.9b-c and e-f.Obviously,the DRXed grains show a randomly distributed orientation,which are not related to their parent grains.

    Fig.8.EBSD observation results of the ZK60 Mg alloy after 30(a-c),60(d-f)and 120(g-i)forging pass:(a,d,g)inverse pole figure map,(b,e,h)corresponding boundary misorientation map and(c,f,i)distribution histogram of grain size.

    From the above discussion,it can be concluded that the grain refinement in the process of MDIF was ascribed to{10–12}twins and multiple rounds of DRX(including CDRX and DDRX),and CDRX was the dominant grain refinement mechanism.Galiyev et al.[40]have compared the DRX behavior of ZK60 Mg alloy at temperatures ranging from 150 to 450 °C and strain rates between 10-5and 10-1s-1.It was found that the mechanisms of DRX depended on the operating deformation mechanisms which changed with temperature.The CDRX and DDRX were observed at intermediate temperature of 200-250 °C and high temperatures of 300-450 °C,respectively.However,in current study the CDRX is the dominant grain refinement mechanism during the whole MDIF process,even if the temperature of the forging is always higher than 350°C(Table 3).This unusual phenomenon may be related to the high strain rate(~10 s-1)of MDIF.On one hand,the high strain rate promoted the CDRX process by activating a large number of{10–12}twins.On the other hand,the high strain rate limited the nucleation of DDRX to a certain extent.

    3.3.Texture evolution during MDIF process

    Fig.10 shows the evolution of(0002)pole figures and corresponding inverse pole figures in the ZK60 Mg alloy during MDIF process.After the first forging pass,one strong basal texture was formed with most basal poles rotating towards FFD,and the maximal intensity of basal texture increased to 15.89(Fig.10a).According to the corresponding inverse pole figures(Fig.10h),the texture component was mainly<0001>‖F(xiàn)FD texture and still contains the residual〈10–10〉fiber texture.As mentioned above,the<0001>‖F(xiàn)FD texture was obviously related to lots of activated{10–12}twins after the first forging pass.In addition,basal slip was also nonnegligible to the formation of this texture component.Although the CRSS of non-basal slip decreased significantly at high temperature,basal slip was still the dominant mechanism in the deformation process[13,41–42].The residual〈10–10〉fiber texture could attribute to the small strain in single forging pass.After 3 forging passes,the basal texture was significantly weakened,and the maximal intensity of basaltexture reduced to 6.37 as shown in Fig.10b.Interestingly,the predominant texture component was<10–10>‖F(xiàn)FD texture once again,while<0001>‖F(xiàn)FD texture component decreased a lot(Fig.10i),which was probably related to detwinning behavior.As reported[43],the pre-existing twins would become narrower or disappear when the strain path changes.As shown in Fig.10c,d,j and k,with the continuous forging,the basal texture does not change much,and its texture component mainly consists of<0001>‖F(xiàn)FD and<10-10>‖F(xiàn)FD texture.Meanwhile,in addition to the two peaks in the FFD direction,another two peaks were gradually formed in the LFD direction,which rotated about 30°~50°away from the center of the(0002)pole figure.Previous studies showed that the equal channel angular extrusion(ECAE)process could apply the simple shear to the material at the 90°angled channel portion,leading to the basal plane with the majority of grains rearranged along the shear plane[44,45].Fig.11 shows the schematic diagram of metal flow on LFDND section.Clearly,two shear planes along the diagonal of LFD-ND plane were produced during MDIF process,which would cause the basal plane to rotate in the direction parallel to these two shear planes,forming the above two peaks on the(0002)pole figure.After 30 forging passes,with annihilation of the original microstructure(Fig.8a),the initial〈10–10〉fiber texture disappeared at the same time,replaced by a unique four-peak texture(Fig.10e).With the continuous increase of forging passes,despite that the unique four-peak texture state has been maintained,the basal texture has been weakened continuously(Fig.10f and g).As mentioned above,the DDRX process became active after 30 forging passes,in addition to the CDRX process.The correlation between the orientation of DRXed grains,especially DDRXed grains,and the parent grains diminished rapidly.Therefore,the progressively increased fraction of DRXed grains resulted in a weakening texture.Besides,the<10-10>‖F(xiàn)FD texture gradually transformed into<11-20>‖F(xiàn)FD texture as shown in Fig.10l,m and n.From Table 3,we could know that the sample temperature was always higher than 350°C during the whole MDIF process,which was very beneficial to the activation of non-basal slip.This may be the reason for the transformation of texture components.From the above,it can be concluded that the special strain path(i.e.,the continuous changes in the forging direction)is the key to the formation of the unique four-peak texture.In addition,the activation of different deformation modes has a significant influence on the texture evolution of the MDIF process.At the beginning of MDIF process,the activated{10–12}twinning led to the formation of<0001>//FFD texture component.With the continuous forging,especially after 30 forging passes,the basal slip played a dominant role in texture evolution.Finally,it is noteworthy that the small strain in single forging pass is crucial for the formation multiple texture components during MDIF process.

    Fig.9.The details of DDRX behavior and corresponding effect on the crystallographic orientation evolution in the different regions(a-c)R4 and(d-f)R5 selected in Fig.8a and d,respectively:(a,d)inverse pole figure maps,(b,e)(0002)pole figure and(c,f)inverse pole figure.

    3.4.Mechanical properties

    Fig.12 displays room temperature tension and compression stress-strain curves of the as-extruded and MDIF120ed ZK60 Mg alloy with different direction,and the corresponding data for the yield strength(YS),ultimate strength(US)andfracture elongation(FE)are listed in it.For tension properties,the tensile yield strength(TYS)along the FFD decreased from 251.9MPa to 221.5MPa,while the TYS along the LFD increased from 124.5MPa to 210.6MPa.For compression properties,the compressive yield strength(CYS)along the FFD and LFD increased to 215.8MPa and 198.2MPa,respectively.

    Fig.10.The evolution of(0002)pole figures and corresponding inverse pole figures in the ZK60 Mg alloy during MDIF process.

    Fig.11.Schematic diagram of metal flow on LFD-ND section(the orange arrows point to the direction of metal flow).

    It is well known that the main strengthening mechanisms of Mg alloys include,but are not limited to,grain strengthening,precipitation strengthening,dislocation strengthening and texture strengthening.According to the well-known Hall-Petch relationship[46],grain refinement serves to enhance yield strength.Thus,the fine and homogeneous grains of the MDIF120ed Mg alloy had an important contribution to the improvement of yield strength.Fig.13 shows the SEM images of the as-extruded and MDIF120ed alloy,respectively.It can be clearly seen that second phase particles with dimensions in the approximate range 0.5–3μm precipitate along ED in the as-extruded alloy(Fig.13a),and the EDS results exhibited that these particles are MgZn2and MgZn phase.After 120 forging passes,the size of second phase particles was reduced to less than 1μm,and the distribution of these second phase particles was more random(Fig.13b).Regrettably,the number of second phase particles was very limited.Therefore,the effect of precipitation strengthening on the yield strength of the MDIF120ed ZK60 alloy was almost negligible.The kernel average misorientation(KAM)map was usually used to reflect an orientation gradient and the residual dislocation density distribution in the grains,i.e.,the higher KAM value indicated the higher dislocation density[47].As shown in Fig.14,the average misorientation values in as-extruded and MDIF120ed alloys were 0.84° and 0.93°,respectively,indicating the density of residual dislocations in as-extruded alloy was higher than that of MDIF120ed alloy.Obviously,dislocation strengthening had a certain contribution to the improvement of yield strength for MDIF120ed alloy.

    Fig.12.Room temperature tension and compression stress-strain curves of the ZK60 Mg alloy:(a)as-extruded;(b)MDIF120ed(Ten:tension test;Com:compression test;YS:yield strength;US:ultimate strength;FE:fracture elongation).

    Fig.13.SEM images of the ZK60 Mg alloy:(a)as-extruded,(b)MDIF120.

    However,the TYS along the FFD decreased significantly,which was mainly related to the textural softening after the MDIF process.It is well known that basal slip and{10–12}twinning are the dominant deformation mechanism at room temperature.Thus,referring to the researches of Koike et al.[48]the average Schmid factor of basal slip(mbas.)and{10–12}twinning(mtwin)in tension and compression along ED/FFD and TD/LFD were calculated from inverse pole figures for as-extruded and MDIF120ed ZK60 Mg alloy as shown in Fig.15.The Schmid factor of basal slip and{10–12}twinning for tension along FFD respectively increase from 0.115 and 0.006 to 0.209 and 0.156,which means that the basal slip and{10–12}twinning are easier to be activated when tension along FFD.And it seems that the effect of texture softening overcomes the grain and dislocation strengthening,so the TYS along FFD is significantly reduced.Besides,it is worth pointing out that the difference in the yield strength of MDIF120ed alloy decreased significantly,which was closely related to the unique four-peak texture obtained after 120 forging passes.Previous study[41]had shown that the alloy usually exhibited high yield strength(or low yield strength)when the initial deformation was dominated by crystallographic slips with high CRSS(or{10–12}twinning with low CRSS).Thus,the difference of{10–12}twinning activation at the initial deformation of the as-extruded alloy was the main reason for the tension/compression asymmetry and anisotropy.Compared with the as-extruded alloy,the difference ofmtwinwas obviously reduced when the MDIF120ed alloy was stretched and compressed in different directions,which made the difference in yield strength mainly caused by{10–12}twinning also decrease.

    Fig.14.The KAM maps of the ZK60 Mg alloy:(a)as-extruded,(b)MDIF120.

    Fig.15.Schmid factors of basal slip(mbas.)and{10–12}twinning(mtwin)in tension and compression along ED/FFD and TD/LFD calculated from inverse pole figures for as-extruded and MDIF120ed ZK60 Mg alloy.

    Fig.16 shows the comparison of yield strengths between the present study and other previous literatures[3–13].It is clear that the wrought Mg alloy processed by the traditional extrusion or rolling process often shows severe yield strength asymmetry due to the formation of strong basal texture.As shown in Fig.16a,the tension/compression yield strength symmetry of Mg alloy rods was improved by CEC and ECAP process compared to traditional extrusion process.Zhang et al.[12]reported that the tension yield strength anisotropy of ZK60 Mg alloy sheets was improved by extrusion and multi-pass rolling with lowered temperature(Fig.16b).For ease of presentation,ED/FFD are collectively called LD,and TD/LFD are collectively called TD in the present study.At the same time,the tension/compression yield strength asymmetry was quantified by the ratio of the tension/compression yield strength along the LD(i.e.,TYS-ED/CYS-EDand TYS-FFD/CYS-FFD).Similarly,the ratio of the tension yield strength along LD and TD(i.e.,TYS-ED/TYS-TDand TYS-FFD/TYS-LFD)was used to quantify the tension yield strength anisotropy.According to the experimental results,the above four ratios are respectively 1.86 and 2.02 in the initial material as well as 1.02 and 1.05 in the MDIF120ed ZK60 Mg alloy,i.e.,the tension/compression yield strength symmetry and the tension yield strength isotropy are significantly improved through MDIF process,which is beneficial for the application of Mg alloys under complex loads.

    Fig.16.Comparison of yield strengths between the present study and other previous literature[3-13]:(a)TYS vs.CYS;(b)TYS-LD vs.TYS-TD.

    4.Conclusions

    The present study confirms that it is feasible to regulate the microstructure and improve yield strength symmetry in the as-extruded ZK60 Mg alloy by multi-directional impact forging(MDIF).The forged piece with average grain size of 5.3μm,unique four-peak texture and improved yield strength symmetry were obtained after MDIF process.The following conclusions can be made:

    (1)A great amount of{10–12}twins were activated at the beginning of MDIF process.The selection mechanism of various twin variants was governed by the Schmid law.Besides,these activated twins play an important role in grain refinement.On one hand,the{10–12}twins segmented the initial coarse grain.On the other hand,the{10–12}twins facilitated the subsequent DRX process.

    (2)Multiple rounds of DRX existed in grain refinement with dominant mechanism of CDRX during the whole MDIF process and DDRX turning active after 30 forging passes.The CDRXed grains showed a clearly preferred orientation related to the parent grains,while the orientations of DDRXed grains were completely different from their parent grains.

    (3)The special strain path is the key to the formation of the unique four-peak texture.The{10–12}twinning and basal slip were two dominant factors to the evolution of texture during MDIF process.At the beginning of MDIF process,the activated{10–12}twinning led to the formation of<0001>//FFD texture component.With forging proceeding,the amount of{10–12}twinning decreased and the basal slip played a dominant role in the texture evolution.After 30 passes,the initial〈10–10〉fiber texture was completely replaced by a unique four-peak texture.With the forging passes increase to 120,the basal texture has been weakened continuously due to DRX process.

    (4)Through 120 passes MDIF,the yield strength of alloy had been significantly improved under the combined effects of grain strengthening and dislocation strengthening,except for the TYS along FFD.Besides,the symmetry of yield strength was greatly improved by MDIF process.

    Declaration of Competing Interest

    The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

    Acknowledgments

    This work was supported by National Natural Science Foundation of China(Grant No.51975146),Key Research and Development Plan in Shandong Province(Grant No.2018JMRH0412,2019JZZY010364),National Defense Basic Scientific Research of China(Grant no.JCK2018603C017)

    岛国视频午夜一区免费看| 高潮久久久久久久久久久不卡| 成人精品一区二区免费| 免费无遮挡裸体视频| 亚洲成人久久性| 久久国产精品男人的天堂亚洲| 亚洲熟妇熟女久久| 日本 欧美在线| 国产熟女午夜一区二区三区| 大码成人一级视频| 看片在线看免费视频| 亚洲av五月六月丁香网| 亚洲精品在线观看二区| 精品乱码久久久久久99久播| 51午夜福利影视在线观看| 在线观看日韩欧美| 91大片在线观看| 在线十欧美十亚洲十日本专区| 亚洲专区中文字幕在线| 午夜福利,免费看| 精品免费久久久久久久清纯| 黄色片一级片一级黄色片| 婷婷丁香在线五月| 人人澡人人妻人| 亚洲午夜精品一区,二区,三区| av中文乱码字幕在线| 亚洲精品美女久久av网站| 国产精品 国内视频| 女人精品久久久久毛片| 一级毛片精品| 亚洲国产高清在线一区二区三 | 国产精品国产高清国产av| 日本五十路高清| 在线天堂中文资源库| 这个男人来自地球电影免费观看| 大码成人一级视频| 亚洲一区二区三区不卡视频| 一区二区三区高清视频在线| 宅男免费午夜| 久久亚洲真实| 色综合欧美亚洲国产小说| netflix在线观看网站| 12—13女人毛片做爰片一| 国产免费av片在线观看野外av| 午夜亚洲福利在线播放| 免费在线观看亚洲国产| 啦啦啦韩国在线观看视频| 日韩中文字幕欧美一区二区| 一a级毛片在线观看| 免费看美女性在线毛片视频| 99久久国产精品久久久| 人妻丰满熟妇av一区二区三区| 精品少妇一区二区三区视频日本电影| 99re在线观看精品视频| 国产伦人伦偷精品视频| 日本撒尿小便嘘嘘汇集6| 欧美最黄视频在线播放免费| 成人特级黄色片久久久久久久| 男女下面进入的视频免费午夜 | 啦啦啦 在线观看视频| 午夜免费激情av| 欧美另类亚洲清纯唯美| 熟妇人妻久久中文字幕3abv| 国产高清视频在线播放一区| 十八禁网站免费在线| 大香蕉久久成人网| 伦理电影免费视频| 国产乱人伦免费视频| 啦啦啦免费观看视频1| 国产av精品麻豆| 三级毛片av免费| 99精品在免费线老司机午夜| 欧美亚洲日本最大视频资源| 黄片小视频在线播放| 久久精品91无色码中文字幕| 美女扒开内裤让男人捅视频| 超碰成人久久| 亚洲少妇的诱惑av| 久久久国产精品麻豆| 香蕉丝袜av| 欧美色视频一区免费| 国产日韩一区二区三区精品不卡| 亚洲欧美精品综合一区二区三区| 国产又色又爽无遮挡免费看| 欧美日韩亚洲综合一区二区三区_| 18禁黄网站禁片午夜丰满| 中文字幕久久专区| 国产一区二区三区视频了| 美女高潮喷水抽搐中文字幕| a在线观看视频网站| 黄色丝袜av网址大全| 国产精品98久久久久久宅男小说| 亚洲国产看品久久| 两个人视频免费观看高清| 亚洲成国产人片在线观看| 亚洲国产欧美网| 自线自在国产av| 国产三级黄色录像| 操出白浆在线播放| 免费一级毛片在线播放高清视频 | 亚洲一卡2卡3卡4卡5卡精品中文| 怎么达到女性高潮| 国产成人欧美| 一二三四社区在线视频社区8| 一边摸一边抽搐一进一小说| www.熟女人妻精品国产| 国产精品一区二区精品视频观看| 国产主播在线观看一区二区| 亚洲黑人精品在线| 校园春色视频在线观看| 亚洲一区中文字幕在线| 精品国产一区二区三区四区第35| 精品免费久久久久久久清纯| 婷婷丁香在线五月| 色婷婷久久久亚洲欧美| 久久国产精品男人的天堂亚洲| 午夜亚洲福利在线播放| 久久精品国产99精品国产亚洲性色 | 18禁观看日本| 国产欧美日韩精品亚洲av| 国产精华一区二区三区| xxx96com| 亚洲中文字幕一区二区三区有码在线看 | 在线天堂中文资源库| 99精品久久久久人妻精品| 啦啦啦韩国在线观看视频| 国产高清视频在线播放一区| 成人免费观看视频高清| 国内精品久久久久久久电影| 亚洲国产日韩欧美精品在线观看 | 国产三级在线视频| 国产av精品麻豆| 欧美中文日本在线观看视频| www日本在线高清视频| 丁香欧美五月| 男女下面插进去视频免费观看| 色综合欧美亚洲国产小说| 9热在线视频观看99| 日本 av在线| 免费搜索国产男女视频| 国产av一区在线观看免费| 亚洲熟女毛片儿| 99精品欧美一区二区三区四区| 成年人黄色毛片网站| 亚洲欧美日韩高清在线视频| 纯流量卡能插随身wifi吗| 国产亚洲欧美在线一区二区| 亚洲人成电影免费在线| 黄色毛片三级朝国网站| 自线自在国产av| 俄罗斯特黄特色一大片| 成年女人毛片免费观看观看9| 欧美国产精品va在线观看不卡| 日本欧美视频一区| 欧美成人性av电影在线观看| 首页视频小说图片口味搜索| 国产精品乱码一区二三区的特点 | 日韩欧美在线二视频| 在线观看66精品国产| 91麻豆精品激情在线观看国产| 大香蕉久久成人网| 精品国内亚洲2022精品成人| 此物有八面人人有两片| 香蕉丝袜av| 亚洲男人的天堂狠狠| 一二三四在线观看免费中文在| 91麻豆精品激情在线观看国产| 久久九九热精品免费| 免费观看精品视频网站| 97碰自拍视频| 少妇裸体淫交视频免费看高清 | 宅男免费午夜| 欧美色视频一区免费| 丝袜美足系列| 亚洲国产精品999在线| 亚洲七黄色美女视频| 高清在线国产一区| 精品国产超薄肉色丝袜足j| 国产私拍福利视频在线观看| 久久久国产成人免费| 在线国产一区二区在线| 国产野战对白在线观看| 亚洲av第一区精品v没综合| 多毛熟女@视频| 亚洲中文字幕日韩| 国产精品,欧美在线| 香蕉国产在线看| 日日摸夜夜添夜夜添小说| 亚洲精品一区av在线观看| av在线天堂中文字幕| 中文字幕色久视频| 国产精品98久久久久久宅男小说| 亚洲av美国av| 非洲黑人性xxxx精品又粗又长| 成人永久免费在线观看视频| 中文字幕人成人乱码亚洲影| 国产成人精品无人区| 丰满人妻熟妇乱又伦精品不卡| 精品一区二区三区视频在线观看免费| 欧美日韩中文字幕国产精品一区二区三区 | 99在线视频只有这里精品首页| 日韩大尺度精品在线看网址 | 精品久久蜜臀av无| 国产视频一区二区在线看| 亚洲美女黄片视频| 琪琪午夜伦伦电影理论片6080| 十分钟在线观看高清视频www| 成人国产综合亚洲| 亚洲,欧美精品.| 真人一进一出gif抽搐免费| 国产亚洲精品综合一区在线观看 | 国产亚洲精品av在线| av欧美777| 国产av又大| 国产成人精品久久二区二区免费| 欧美一区二区精品小视频在线| 久久中文看片网| 亚洲国产欧美一区二区综合| 欧美另类亚洲清纯唯美| 欧美精品啪啪一区二区三区| 久久国产乱子伦精品免费另类| 国产精品av久久久久免费| 日本vs欧美在线观看视频| 热re99久久国产66热| 18禁观看日本| 亚洲无线在线观看| 国产精品美女特级片免费视频播放器 | 欧美成狂野欧美在线观看| 国产高清videossex| 在线观看66精品国产| 日韩欧美一区二区三区在线观看| 男人操女人黄网站| 韩国av一区二区三区四区| 国产不卡一卡二| 亚洲五月天丁香| 久久久精品国产亚洲av高清涩受| 免费在线观看日本一区| 欧美+亚洲+日韩+国产| 成人免费观看视频高清| 国产97色在线日韩免费| 久久精品国产综合久久久| 最好的美女福利视频网| 国产精品爽爽va在线观看网站 | 日韩av在线大香蕉| 美女 人体艺术 gogo| 中文字幕高清在线视频| 91字幕亚洲| 久久香蕉国产精品| 无人区码免费观看不卡| 日日爽夜夜爽网站| 国产av在哪里看| 一夜夜www| 精品无人区乱码1区二区| 亚洲在线自拍视频| 亚洲 国产 在线| 成人亚洲精品一区在线观看| 可以在线观看的亚洲视频| 韩国av一区二区三区四区| 国产精品久久久av美女十八| 免费女性裸体啪啪无遮挡网站| 99久久综合精品五月天人人| 国语自产精品视频在线第100页| av视频免费观看在线观看| 国产色视频综合| 50天的宝宝边吃奶边哭怎么回事| 女人被躁到高潮嗷嗷叫费观| 久久久久久国产a免费观看| 亚洲人成电影免费在线| 丁香六月欧美| 美女大奶头视频| 日日干狠狠操夜夜爽| 法律面前人人平等表现在哪些方面| 欧美激情久久久久久爽电影 | av片东京热男人的天堂| 9191精品国产免费久久| 美女大奶头视频| 在线观看午夜福利视频| 国产精品久久电影中文字幕| 国产视频一区二区在线看| www.999成人在线观看| 制服诱惑二区| 中文字幕久久专区| 国产一区二区三区视频了| 国产一区二区在线av高清观看| tocl精华| 国内精品久久久久精免费| 亚洲少妇的诱惑av| 欧美在线一区亚洲| 欧美中文综合在线视频| 国产午夜福利久久久久久| 国产亚洲欧美在线一区二区| 很黄的视频免费| 国产亚洲精品av在线| 男女下面进入的视频免费午夜 | 久久人妻福利社区极品人妻图片| 少妇的丰满在线观看| av免费在线观看网站| 宅男免费午夜| 色精品久久人妻99蜜桃| 国产精品一区二区免费欧美| 亚洲专区中文字幕在线| 香蕉丝袜av| 国产精品 欧美亚洲| 久久婷婷成人综合色麻豆| 美女高潮到喷水免费观看| 美女 人体艺术 gogo| 色婷婷久久久亚洲欧美| 亚洲视频免费观看视频| 久9热在线精品视频| 成人永久免费在线观看视频| 一区福利在线观看| 老鸭窝网址在线观看| 久久人妻av系列| 悠悠久久av| 黑丝袜美女国产一区| 精品久久蜜臀av无| 国产精品免费视频内射| 男女做爰动态图高潮gif福利片 | 麻豆一二三区av精品| 91成人精品电影| a级毛片在线看网站| 久久人妻av系列| www.自偷自拍.com| 欧美在线一区亚洲| 欧美大码av| 亚洲专区中文字幕在线| 51午夜福利影视在线观看| 日韩欧美国产在线观看| 老司机靠b影院| 香蕉丝袜av| 亚洲人成伊人成综合网2020| 国产精品国产高清国产av| 精品乱码久久久久久99久播| 国产成人av教育| 亚洲自偷自拍图片 自拍| 丰满的人妻完整版| 香蕉国产在线看| 国产1区2区3区精品| 国产又爽黄色视频| 久久精品成人免费网站| 亚洲欧美日韩高清在线视频| 国产男靠女视频免费网站| 极品教师在线免费播放| 精品国产一区二区久久| 中文字幕精品免费在线观看视频| 婷婷六月久久综合丁香| 国产亚洲av嫩草精品影院| 亚洲国产日韩欧美精品在线观看 | 亚洲精品一卡2卡三卡4卡5卡| 黄片小视频在线播放| 精品国产一区二区久久| 精品福利观看| 黄色视频不卡| 老司机午夜福利在线观看视频| 亚洲中文字幕日韩| 午夜福利免费观看在线| 成人亚洲精品av一区二区| 国产一级毛片七仙女欲春2 | 两个人视频免费观看高清| 亚洲精品国产色婷婷电影| 久久久久久人人人人人| 精品免费久久久久久久清纯| 精品第一国产精品| 国产精品久久久久久亚洲av鲁大| 一夜夜www| 50天的宝宝边吃奶边哭怎么回事| 国产成人系列免费观看| 1024视频免费在线观看| 啦啦啦观看免费观看视频高清 | 成年女人毛片免费观看观看9| 在线观看www视频免费| 久久人妻熟女aⅴ| 成人18禁高潮啪啪吃奶动态图| 婷婷精品国产亚洲av在线| 69av精品久久久久久| 欧美一级a爱片免费观看看 | 欧美久久黑人一区二区| 亚洲专区中文字幕在线| 成人亚洲精品一区在线观看| 久久伊人香网站| 欧美+亚洲+日韩+国产| 啪啪无遮挡十八禁网站| 中文字幕久久专区| 搡老岳熟女国产| 日韩大码丰满熟妇| 午夜免费鲁丝| 久久国产乱子伦精品免费另类| 中国美女看黄片| 黄色毛片三级朝国网站| 久久人人精品亚洲av| a在线观看视频网站| 在线观看舔阴道视频| 18禁国产床啪视频网站| 热99re8久久精品国产| 欧美不卡视频在线免费观看 | 女人爽到高潮嗷嗷叫在线视频| 国产精品久久久人人做人人爽| 黄片大片在线免费观看| 色综合婷婷激情| 1024香蕉在线观看| 国产麻豆成人av免费视频| 国产乱人伦免费视频| 亚洲成人国产一区在线观看| 自拍欧美九色日韩亚洲蝌蚪91| 亚洲一区二区三区色噜噜| 亚洲国产欧美一区二区综合| 亚洲中文日韩欧美视频| 久久精品国产清高在天天线| 亚洲欧美激情综合另类| 精品国产亚洲在线| 午夜福利免费观看在线| 黑人欧美特级aaaaaa片| 亚洲国产精品999在线| 99在线视频只有这里精品首页| 又黄又爽又免费观看的视频| 在线天堂中文资源库| 日本三级黄在线观看| 久久久久亚洲av毛片大全| 亚洲一码二码三码区别大吗| 国内精品久久久久精免费| av视频免费观看在线观看| 老司机午夜十八禁免费视频| 亚洲熟女毛片儿| 搡老妇女老女人老熟妇| 久久热在线av| 一a级毛片在线观看| 久久这里只有精品19| 国产99白浆流出| 欧美在线一区亚洲| netflix在线观看网站| 亚洲,欧美精品.| 亚洲欧美精品综合久久99| 精品国产超薄肉色丝袜足j| 黄频高清免费视频| 精品第一国产精品| 国产又色又爽无遮挡免费看| 性少妇av在线| 亚洲一区中文字幕在线| 极品教师在线免费播放| 日本三级黄在线观看| 亚洲成人精品中文字幕电影| 女警被强在线播放| 亚洲成人免费电影在线观看| cao死你这个sao货| 色播在线永久视频| 婷婷六月久久综合丁香| 女人被狂操c到高潮| 韩国精品一区二区三区| 免费搜索国产男女视频| 香蕉久久夜色| 久久久国产精品麻豆| 一区二区三区精品91| 午夜老司机福利片| 国产精品98久久久久久宅男小说| 成人免费观看视频高清| 最近最新中文字幕大全电影3 | 757午夜福利合集在线观看| 亚洲精品久久成人aⅴ小说| 国产区一区二久久| 国产乱人伦免费视频| 久久人妻福利社区极品人妻图片| 免费在线观看日本一区| 99精品欧美一区二区三区四区| 国产成人欧美在线观看| 在线观看www视频免费| 中文字幕另类日韩欧美亚洲嫩草| 九色国产91popny在线| 亚洲欧美日韩无卡精品| 日韩高清综合在线| 可以在线观看毛片的网站| 涩涩av久久男人的天堂| 在线观看免费日韩欧美大片| 亚洲色图av天堂| 亚洲视频免费观看视频| 亚洲av电影不卡..在线观看| 国产精品免费视频内射| or卡值多少钱| 成人三级做爰电影| 嫩草影视91久久| 男人操女人黄网站| 美女国产高潮福利片在线看| 久久久久久久午夜电影| 欧美大码av| 999久久久国产精品视频| 69av精品久久久久久| 99久久99久久久精品蜜桃| 一进一出好大好爽视频| 亚洲中文字幕一区二区三区有码在线看 | 免费看美女性在线毛片视频| 国产在线精品亚洲第一网站| 亚洲国产毛片av蜜桃av| av片东京热男人的天堂| 国产精品综合久久久久久久免费 | 极品人妻少妇av视频| 一边摸一边抽搐一进一出视频| 亚洲中文av在线| 亚洲男人的天堂狠狠| 色哟哟哟哟哟哟| 国产精品久久久人人做人人爽| 国产97色在线日韩免费| 乱人伦中国视频| 国产精品久久久久久人妻精品电影| 99精品在免费线老司机午夜| 亚洲激情在线av| 亚洲第一电影网av| 好男人电影高清在线观看| 亚洲色图 男人天堂 中文字幕| 亚洲三区欧美一区| 麻豆av在线久日| 欧美性长视频在线观看| 国产av精品麻豆| 久久久久久久久中文| 91精品三级在线观看| 欧美大码av| 国产高清激情床上av| 成人三级做爰电影| 村上凉子中文字幕在线| 国产精品美女特级片免费视频播放器 | 欧美另类亚洲清纯唯美| 日韩成人在线观看一区二区三区| aaaaa片日本免费| 大型黄色视频在线免费观看| 亚洲人成电影观看| 精品不卡国产一区二区三区| 亚洲aⅴ乱码一区二区在线播放 | 真人一进一出gif抽搐免费| 久久久久国产精品人妻aⅴ院| 精品久久久久久久毛片微露脸| 9色porny在线观看| 亚洲国产毛片av蜜桃av| 操美女的视频在线观看| 999久久久国产精品视频| 一级作爱视频免费观看| 欧美一区二区精品小视频在线| 制服诱惑二区| 9热在线视频观看99| 国产精品久久久久久精品电影 | 国产人伦9x9x在线观看| 午夜a级毛片| 老司机午夜十八禁免费视频| 亚洲全国av大片| 国产麻豆成人av免费视频| 日韩免费av在线播放| 99在线视频只有这里精品首页| 亚洲av五月六月丁香网| cao死你这个sao货| 熟妇人妻久久中文字幕3abv| 一夜夜www| 国产精品亚洲美女久久久| 亚洲av电影在线进入| 精品国内亚洲2022精品成人| 天堂动漫精品| 久久久久精品国产欧美久久久| 一级a爱片免费观看的视频| 首页视频小说图片口味搜索| 亚洲人成网站在线播放欧美日韩| 久久久久国内视频| 午夜激情av网站| 久久精品国产亚洲av高清一级| www日本在线高清视频| 亚洲七黄色美女视频| 婷婷丁香在线五月| 国产野战对白在线观看| 熟女少妇亚洲综合色aaa.| 亚洲第一青青草原| 国产av一区在线观看免费| 长腿黑丝高跟| 丝袜美足系列| 搡老妇女老女人老熟妇| 精品不卡国产一区二区三区| 十八禁人妻一区二区| 一区二区三区高清视频在线| 午夜精品久久久久久毛片777| 神马国产精品三级电影在线观看 | 长腿黑丝高跟| 亚洲欧美日韩高清在线视频| 亚洲熟妇中文字幕五十中出| 脱女人内裤的视频| 亚洲男人天堂网一区| 怎么达到女性高潮| 男女床上黄色一级片免费看| 欧美久久黑人一区二区| 一二三四社区在线视频社区8| 一级毛片女人18水好多| 黄色视频不卡| 国产成人精品久久二区二区免费| 亚洲人成77777在线视频| 看免费av毛片| 久久久精品欧美日韩精品| 亚洲专区字幕在线| 国产一区二区激情短视频| 成人永久免费在线观看视频| 免费看美女性在线毛片视频| 精品国产国语对白av| 久久久久久久午夜电影| 99国产精品99久久久久| 大陆偷拍与自拍| 少妇熟女aⅴ在线视频| 大型av网站在线播放| 欧美激情久久久久久爽电影 | 国产精品亚洲美女久久久| 性色av乱码一区二区三区2| 国产免费男女视频| 少妇裸体淫交视频免费看高清 | 99国产极品粉嫩在线观看| 国内精品久久久久久久电影| 日本五十路高清| 欧美丝袜亚洲另类 | 久久久国产成人精品二区| 一区二区三区高清视频在线| bbb黄色大片| 村上凉子中文字幕在线| 日本在线视频免费播放| 亚洲久久久国产精品| 久久国产亚洲av麻豆专区|