• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Explosive Electric Actuator and Control for Legged Robots

    2022-08-17 07:18:22FeiMengQingHungZhngguoYuXuechoChenXuxioFnWuZhngAiguoMing
    Engineering 2022年5期

    Fei Meng, Qing Hung*, Zhngguo Yu,*, Xuecho Chen, Xuxio Fn, Wu Zhng, Aiguo Ming

    a School of Mechatronical Engineering, Beijing Institute of Technology, Beijing 100081, China

    b Beijing Advanced Innovation Center for Intelligent Robots and Systems, Beijing Institute of Technology, Beijing 100081, China

    c Key Laboratory of Biomimetic Robots and Systems, Ministry of Education, Beijing 100081, China

    d Department of Mechanical and Intelligent Systems Engineering, The University of Electro-Communications, Tokyo 182-8585, Japan

    Keywords:Electric actuator Variable transmission Integral torque control Legged robot

    ABSTRACT Unmanned systems such as legged robots require fast-motion responses for operation in complex environments.These systems therefore require explosive actuators that can provide high peak speed or high peak torque at specific moments during dynamic motion. Although hydraulic actuators can provide a large force, they are relatively inefficient, large, and heavy. Industrial electric actuators are incapable of providing instant high power.In addition,the constant reduction ratio of the reducer makes it difficult to eliminate the tradeoff between high speed and high torque in a given system. This study proposes an explosive electric actuator and an associated control method for legged robots. First, a high-powerdensity variable transmission is designed to enable continuous adjustment of the output speed to torque ratio.A heat-dissipating structure based on a composite phase-change material(PCM)is used.An integral torque control method is used to achieve periodic and controllable explosive power output. Jumping experiments are conducted with typical legged robots to verify the effectiveness of the proposed actuator and control method. Single-legged, quadruped, and humanoid robots jumped to heights of 1.5, 0.8, and 0.5 m, respectively. These are the highest values reported to date for legged robots powered by electric actuators.

    1. Introduction

    Unmanned intelligent systems such as legged robots can perform a variety of tasks in complex environments. One advantage of legged robots is their capability for highly dynamic motion,including actions such as running and jumping. However, legged robots have size and weight limits and thus require highperformance actuators. Unlike typical industrial systems, which have high-rated power actuators and operate in fixed working environments, legged robots often operate in complex environments that require fast-motion responses [1-3]. Therefore, legged robots require high explosive power actuators to provide high peak speed or high peak torque at specific moments during their dynamic motion.

    Hydraulic actuators have high power and are naturally robust against impulsive loads. For example, the Atlas robot developed by Boston Dynamics uses hydraulic actuators to achieve highly diverse and agile locomotion [4]. However, hydraulic systems are inefficient when operated at constant pressure. It is thus difficult to position the onboard supply, which makes legged robots rather large and heavy [5]. Hydraulic systems may also leak oil [6].

    Electric motor actuators are more compact and have a more constant output torque profile compared with hydraulic actuators.Pseudo-direct-drive systems use a high-torque motor in combination with a low-reduction-ratio gearing system.The actuator’s output force can thus be controlled accurately via the motor current with high transparency [7]. For example, the Cheetah robot [8-10]developed by Massachusetts Institute of Technology(MIT)uses a high-torque-density motor actuator with a large gap radius[7,11]. However, large actuators are unsuitable for use in legged robots with a relatively large number of degrees of freedom(DoFs),such as humanoid robots.

    Many legged robots with a high number of DoFs, including ASIMO[12],ATRIAS[13],and ANYmal[5],have strict actuator size limitations. These robots use small high-speed motors with relatively high-ratio reducers to support the heavy robot trunks[12-14]. However, high-ratio reducers increase friction and introduce nonlinear elements into the actuator, which means that the force cannot be controlled directly using the motor current. The National Aeronautics and Space Administration (NASA) Valkyrie[15], Cassie [16], and DLR robots [17] use series elastic actuators(SEAs) or similar force sensors to implement accurate actuator force control.However,the elastic parts of an SEA or a force sensor cannot absorb the explosive impacts that occur during dynamic motion. These robots have poor dynamic motion performance because the high-ratio reducer required for the SEA, or the force sensor used for force control,increases friction and introduces nonlinear elements into the actuator.

    Animal muscles can provide high instant power for a diverse range of agile movements [18]. The relationship among the force,length,and velocity properties of muscles contributes to providing the explosive power necessary for dynamic movements such as throwing, kicking, and jumping [19]. In addition, the pair of cruciate ligaments that is present in animal joints serves as a variable transmission[20].Animals can maintain a relatively constant core temperature through a dynamic balance between endogenous heat-production and heat-dissipation to the surrounding environment during movement[21].In summary,animal muscles produce explosive power, have a variable transmission, and dissipate heat.

    The reduction ratio represents a tradeoff between torque and speed. Some researchers have thus designed actuators with continuously variable transmissions or infinitely variable transmissions for use in robots [22,23]. These designs involve complex transmission chains that are difficult to install on small actuators.Another type of actuator uses two motors to control the sun gear and the ring gear of a planetary reducer[24-26].In this type of system,an optimal control method is required to regulate the coupled relationship between the two motors. To enhance actuator heatdissipation, some robotic systems use liquid cooling systems to ensure that the actuator operation remains sufficiently stable to allow it to support dynamic motion[27-29].However,liquid cooling systems require bulk liquid storage to perform the heatexchange operation and usually require integration of the liquid cooling channels into the robot system.

    In this study, we propose an explosive electric actuator and its control method for application in legged robots.This actuator provides high peak speed or high peak torque at specific moments during robot dynamic motion. We perform jumping experiments using typical legged robots to verify the effectiveness of the proposed actuator. The main contributions of this work are summarized as follows:

    (1) To eliminate the tradeoff between high speed and high torque for legged robots,we add a power allocation unit to control the rotational speed of the first-stage ring gear in a two-stage planetary gear train in order to adjust the reduction ratio. This highpower-density variable transmission allows continuous and efficient adjustment of the ratio of the speed to the output torque.

    (2)The robot actuator cannot operate continuously in the highpower output state because of heat accumulation. Therefore, we design a heat-dissipating structure based on a composite phasechange material (PCM). An integral torque control method is used to achieve periodic and controllable explosive power output from the actuator.

    The remainder of this paper is organized as follows.In Section 2,we present the design concept and provide a detailed description of the proposed explosive electric actuator.In Section 3,we derive the explosive power control method. In Section 4, we present the results of jumping experiments conducted using single-legged,quadruped,and humanoid robots.Finally,in Section 5,we summarize and discuss our results.

    2. Design of the explosive electric actuator

    To provide high peak speed or high peak torque for legged robots at specific moments during their dynamic motion, we design a high-power-density variable transmission for continuous adjustment of the ratio of the speed to the output torque. A heatdissipating structure based on a composite PCM is used to remove heat from the actuator during power output. To balance the actuator’s explosive power, transparency, and size requirements,an integral actuator was designed.

    2.1. High-power-density variable transmission

    The actuators with continuously variable transmission or infinitely variable transmission that are currently used in unmanned systems have complex structures that cannot tolerate the impact forces that are applied to legged robots. Therefore, we design a high-power-density variable transmission based on a two-stage planetary reducer. The transmission connection diagram and the structure of the proposed reducer are both shown in Fig. 1.

    The main power transmission system is based on the two-stage planetary reducer, which is small, lightweight, and reliable. We add a power allocation unit to this transmission system to control the first-stage ring gear’s rotational speed and thus enable adjustment of the reduction ratio.

    In Fig.1,ωr1is the first-stage ring gear rotational speed,and Nr1is the first-stage ring gear number of teeth. ωp1and Np1are the first-stage planetary gear rotational speed and number of teeth,respectively.ωr2and Nr2are the second-stage ring gear rotational speed and number of teeth, respectively. ωp2and Np2are the second-stage planetary gear rotational speed and number of teeth,respectively.ωsand Nsare the sun gear rotational speed and number of teeth,respectively.Finally,ωcis the planet carrier rotational speed.

    From the transmission connection diagram shown in Fig. 1(a),we can determine the following relationships between the different transmission gears:

    The first-stage planetary gear and the second-stage planetary gear are fixed on the same axle; therefore, we obtain ωp1=ωp2.Using this relationship and Eq. (1), the reduction ratio i can then be calculated as follows:

    If the first-stage ring gear is static(i.e.,ωr1=0),then the system is a standard two-stage planetary gear train, and the reduction ratio ifixedis given by

    from which Eq. (2) can be rewritten as follows:

    Fig. 1. Transmission connection diagram and structure of the proposed high-power-density variable transmission. (a) Transmission connection diagram; (b) transmission structure. M: motor.

    To implement the designed power allocation unit, we used a small power motor and a high-ratio gearbox. We selected these components because the actuator does not require peak speeds during most of its operation,and the power allocation motor therefore rarely consumes energy. Unlike systems that use dual motors to control the sun and ring gears of a planetary reducer[24,26],our power allocation motor is much smaller than the main actuator motor. Therefore, the energy efficiency of the proposed unit is higher than that of the previous dual motor systems, and there is no coupling between the two motors in the proposed system.

    2.2. Heat-dissipating structure

    A major restriction that prevents high output power from being realized with electric actuators is heat accumulation, particularly at high currents. We therefore designed a heat-dissipating structure based on a composite PCM to remove the heat generated at high output power (Fig. 3). The composite PCM releases and absorbs energy during its phase transition to provide either heating or cooling,respectively.The transition is generally from a solid to a liquid phase, or vice versa.

    As shown in Fig. 3, the bottom of the composite PCM container is in direct contact with the motor’s rotor,and the top of the composite PCM container is the actuator surface, which is exposed to the air. The selection of the composite PCM is dependent on the specific motor heating situation and the actuator’s operating environment. Legged robots emit heat intermittently and thus do not require additional cooling equipment.

    Fig.2. Relationship between the reduction ratio i and the velocity of the first-stage ring gear.

    Fig. 3. Heat-dissipating structure based on the composite PCM.

    The designed explosive electric actuator is shown in Fig. 4(a),along with a photograph of the real actuator(Fig.4(b)).The actuator includes both the high-power-density variable transmission and the heat-dissipating structure. We developed an integrated design that merges the connection parts of the reducer and motor to reduce the number of components required and thus increase the actuator’s power density.

    3. Explosive power control

    The proposed explosive electric actuator can output peak torque or peak speed instantaneously.However,continuous operation in the high-power state may damage either the actuator or the robot. We therefore propose an integral torque control method to achieve periodic and controllable high output power. We achieve effective power control by limiting the total output energy per unit time. The control performance is demonstrated using jumping experiments.

    3.1. Integral torque control method

    Low-ratio actuators can control their output force accurately via the motor current with high transparency. The torque integral of the actuator over a given time period can be expressed as follows:

    where τ is the actuator torque, Δt is the given time period, I is the motor current, kTis the motor torque constant, and i is the reduction ratio. In a real-time controller, we can record the current and the reduction ratio in each period and then calculate the joint torque required to implement the following integral torque control method.

    Fig. 4. (a) Integrated design of the proposed explosive electric actuator and (b) photograph of the real actuator.

    Industrial servo systems are oriented toward the production of their rated output in order to protect the motor from damage caused by overheating. Their controllers have strict peak current limits.However,this control strategy is unsuitable for use in legged robots during dynamic motion.In our design,the motors are often subjected to very high instantaneous currents.

    We use the inertial hysteresis response characteristics of a lowpass filter (LPF) to control the actuator’s peak torque. The corresponding integral torque control method is shown in Fig.5, where τcis the continuous torque limit,τpis the peak torque limit,τtis the variable torque threshold, and τfilteris the equivalent integral of the actual actuator output torque τactual. The actuator model shown in Fig.5 is defined in Eq.(5).Using this model,we can transform the motor current into the actuator torque. Then, based on the flow diagram shown in Fig. 5, we can calculate the active torque limit τlimrequired to constrain the torque command.

    We set the initial value of τlimto τpand the corresponding value of τtto τc. As shown in Fig. 5, when the actual torque τactualis higher than τcover a given time period Δt, the equivalent integral torque τfilterreaches τt,the output limit τlimis adjusted to τc,and τtis then adjusted to 0.9τc.When the actual torque τactualdrops to τtfor a while,the equivalent integral torque τfilterdrops to τt,the output limit τlimis adjusted back to τp,and τtreverts to τcto allow the actuator to provide the high power output again.

    We performed a simulation of the proposed integral torque control method,in which we set the peak torque limit at 300 N·m,the continuous torque limit at 100 N·m, and the power output time duration(T) to 1, 2, 3, or 4 s. During each control period, we input the desired torque τdesired(drawn as the green line in Fig. 6) and then ran the integral torque control method shown in Fig. 5. We calculated the equivalent integral of the actual output torque τfilterand then obtained the output limit τlimfor the next period.The simulation results, which are shown in Fig. 6, demonstrate that the integral torque control method has a flexible parameter configuration and confirm that the method can control the maximum peak torque. We performed dynamic adjustment of τlimto control the integral torque of the actuator. This control method improves the instantaneous output power of the motor and protects the actuator from damage caused by excessive peak output.

    3.2. Explosive jumping control

    Many legged robots use electric motors,parallel structures,and appropriate mechanical design to achieve ballistic and explosive motion [30-32]. To verify the effectiveness of the integral torque control method and the explosive electric actuator proposed in this work, we applied explosive jumping control to a single leg with two parallel actuators. The basic robot leg model (which is shown in the center of Fig. 7) is a symmetrical four-bar linkage mechanism with two actuators.

    We use the integral torque control method in combination with virtual model control (VMC) to implement jumping control. To achieve jumping control, the VMC approach uses the actuator power to imitate virtual component effects, such as the effects of springs and dampers. Unlike a real spring, VMC can change the coefficient immediately in order to adapt both the take-off phase and the touch-down phase of the jumping motion.Fig.7(a) shows a simplified symmetrical leg model with one mass point at the top and a leg mechanism composed of two massless parallel links,and Fig. 7(b) shows the virtual model of the symmetrical leg with a spring-damper system.The leg length l is controlled by the normal effect of the linear spring system, and the leg angle θ is controlled by the tangential effect of the torsional spring system. The virtual force fsprand torque Tsprof the model shown in Fig. 7(b) can be expressed as follows:

    Fig. 5. Integral torque control method. Iactual: actual current; Icommand: command current;τcommand: command torque.

    Fig. 6. Results of simulation of the integral torque control method. (a) T = 1 s; (b) T = 2 s; (c) T = 3 s; (d) T = 4 s.

    Fig. 7. Overview of the explosive jumping control strategy. (a) A simplified symmetrical leg model with one mass point at the top and a leg mechanism composed of two massless parallel links; (b) a virtual model of the symmetrical leg with a spring-damper system. fspr: virtual force of the model; Tspr virtual torque of the model.

    where kvland cvlare the stiffness and the damping coefficient for the virtual linear spring,respectively;kvtand cvtare the corresponding terms for the virtual torsional spring, respectively; l and loriare the actual and desired leg lengths,respectively(see the distance l in Fig. 7(a)); and θ and θoriare the actual and desired leg angles,respectively (see the angle θ in Fig. 7(b)).

    The desired virtual force and torque are converted into the foot force of the robot,which can then be used to calculate the desired actuator torque.The desired virtual linear spring torque τSis calculated as follows:

    where p= [l,θ ]T, T is transpose symbol; fspr, Kv, and Cvare the virtual model parameters,vectors,or matrices in Eq.(6);and JPrepresents the Jacobian matrix between the actuator torque and the robot foot force, P represents polar coordinates. In general, we can control the robot leg to perform with different dynamic characteristics using the actuator’s torque.

    Fig.7 shows a schematic diagram of the explosive jumping control strategy. The different jumping phases are detected based on the leg length. The actuators provide explosive power with a high elastic coefficient during the take-off phase and high damping during the touch-down phase.This periodic and controllable explosive power output permits the robot leg to jump continuously.

    4. Experiment

    4.1. Proposed explosive electric actuator

    We implemented the explosive electric actuator, as shown in Fig. 4. The diameter, length, and mass of the real actuator were 98 mm, 102 mm, and 1.3 kg, respectively. The reduction ratio of the two-stage planetary reducer (ifixed) was 29. The main actuated motor was designed by the authors.The peak torque of this motor was 10.55 N·m and the maximum rotation speed was 3000 r·min-1.The relationship between the speed of the first-stage ring gear and the reduction ratio for various sun gear speeds is shown in Fig. 8.

    We used a Maxon ECX SPEED 16 M motor with a 186:1 reduction ratio planetary gearhead as the power allocation unit. To achieve fast and efficient conversion, we set the reduction ratio range to be from 15 to 29.As a result,the actuator peak output torque was approximately 305 N·m, and the maximum rotational speed was 200 r·min-1. In comparison with the actuator of the MIT Cheetah 3 [10], our explosive electric actuator is smaller in diameter and has a higher peak torque (Table 1); therefore, it is more suitable for use in multi-joint robot systems(e.g., humanoid robots) that have strict actuator size limitations.

    Fig.8. Relationship between the first-stage ring gear speed and the reduction ratio for various sun gear speeds.

    The designed prototype heat-dissipating structure based on the composite PCM is shown in Fig. 9(a). This structure is bonded to the motor stator housing. The structure has a gap with blocks to be filled with the composite PCM. The blocks are used to disperse the composite PCM in the gap. In this prototype, a transparent plastic shell and color blocks were used to allow us to see the phase change during temperature variations. In the real actuator, this structure is made of metal, and the composite PCM is colloidal at indoor temperatures, making it easy to assemble this structure.The mass of the structure is approximately 180 g,and the thickness is approximately 6 mm.

    We performed experiments to test the effectiveness of the heatdissipating structure shown in Fig. 9(a), where the temperature sensor is pasted onto the edge of the motor stator.Fig. 9(b) shows the results from the peak torque duration experiment. The maximum output torque (305 N·m) could be maintained for 1 s, and an output torque of 70 N·m could be maintained continuously.Fig. 9(b) shows that the heat-dissipating structure was incapable of increasing the instantaneous power because of the phase change time of the composite PCM. Fig. 9(c) shows the results from the temperature test.The heat-dissipating structure reduced the actuator temperature effectively. To summarize, although the heatdissipating structure did not increase the actuator’s instantaneous output power, it did reduce the heat accumulation. This result means that the heat-dissipating structure is acceptable for use in legged robots, which do not operate continuously at high output power during dynamic motion.

    To implement force control directly via the actuator current,we measured the current and the torque of the proposed actuator under various working conditions; the results are shown in Fig. 10. Based on these results, we consider the proposed actuator to be sufficiently linear.However,there was still some friction present in the reducer. At high currents (>50 A), the output torque was less linear than the torque at low currents; this was mainly caused by the nonlinearity of the motor, which led it to deviate from its rated state during operation. To overcome this problem,we used the fitting result and revised the nonlinearity at high currents according to the motor parameters.

    4.2. Actuator performance in the jumping experiment

    To evaluate the performance of the proposed actuator when used in a legged robot, we designed a single symmetrical robot leg based on the model described in Section 3.2. The symmetrical leg contains two parallel actuators that rotate relative to the trunk base frame. To reduce the mass of this leg, we used carbon fiber tubes as the leg links and aluminum parts to form the jointconnections. We limited the movement of this robot leg using vertical slide guides in order to realize vertical jumping.

    Table 1Comparison of actuators from our design and MIT Cheetah 3.

    Fig.9. Experimental testing of the heat-dissipating structure.(a)Photograph of the experimental heat-dissipating structure prototype based on the composite PCM;(b)peak torque duration; (c) temperature versus time characteristics.

    Fig. 10. Measured torque versus current characteristics for the actuator.

    In the jumping experiment,the robot took off with a high elastic coefficient and touched down with high damping. The actuators produced explosive power for the take-off and reactive power for the touch-down. The mass of the robot leg was 5.2 kg, with a 3 kg load on top. The initial leg length was 0.42 m, the desired take-off leg length was 0.67 m, and the desired touch-down leg length was 0.55 m. In this experiment, the virtual linear spring stiffness kvlwas 1800 N·mˉ1, and the virtual damping coefficient cvlwas zero during the take-off phase. In the touch-down phase,kvlwas 1000 N·mˉ1, and cvlwas 30 N·smˉ1. Snapshots of the experiment are shown in Fig.11.The legged robot maximum jump height was 1.5 m (from floor to toe).

    Fig.12 shows the reduction ratio,the torque,and the velocity of the first joint actuator during the continuous jumping experiment with a legged robot.The results obtained for two jumps are plotted here to verify that the actuator can provide explosive power periodically.Fig. 12(a) shows the reduction ratio curve. To acquire the high speed required during take-off and then absorb the impact during touch-down, the reduction ratio was reduced to allow the actuator to output a higher speed. Figs. 12(b) and (c) show the actual torque and velocity curves for the jumping experiment,respectively.A slight oscillation was observed in the curves during impact.During the reduction ratio adjustment,the peak torque and the peak velocity did not overlap. The integral torque control method limited the peak torque and thus allowed the actuator to provide explosive power periodically.

    In general,to accelerate at the beginning of the jumping motion,the robot requires the actuators to provide a high torque output;to jump high at the moment of take-off, the robot requires the actuators to provide high speed. It is thus difficult for the constant reduction ratio reducer to eliminate the tradeoff between high torque and high speed during the jumping motion. In our jumping experiment, we selected the reduction ratio range of the joints and then calculated the transform threshold in the simulation. In the real robot experiment, we used a threshold that included the torque and speed values during motion to trigger variable transmission;the power allocation motor then changed speed smoothly to enable continuous adjustment of the reduction ratio. In future work, we will study the complex real-time reduction ratio adjustment method further in order to adapt to other types of highly dynamic motion.

    To verify the advantages of the variable transmission, we present a map of the absolute values of the speed and torque in Fig.13.The figure shows the torque-speed range of the main actuated motor that was introduced in Section 4.1 for different reduction ratios. The range covered by the blue line represents a reduction ratio of 29, which has high torque and low speed. The range covered by the green line represents a reduction ratio of 15, which has low torque and high speed. The variable transmission designed in this work changed the reduction ratio (indicated by the magenta asterisks)to cover all the green,blue,and magenta ranges. The absolute values of the speed and torque recorded (in the period from 0-2 s shown in Figs. 12(b) and (c)) in the legged robot jumping experiment are also shown in the figure. Fig. 13 shows that the designed actuator can provide the high peak speed and high peak torque that are required during the jumping experiment when using variable transmission.

    4.3. Quadruped and humanoid robot jumping experiment

    We applied the proposed actuator to both quadruped and humanoid robots to provide the explosive power required for dynamic jumping. For the legs of the quadruped robot, we used the same structure that was described in Section 4.2; we used the proposed actuators for the hip and knee joints of each leg.The robot’s mass was 37 kg. We built the VMC method based on the quadruped robot’s center of mass (CoM) to conduct the jumping experiment. We set the CoM height to have the same value as the length of the single-legged robot in Section 4.2. We calculated each joint’s torque during the jumping motion using foot force optimization and a Jacobian matrix. Snapshots of the jumping experiment performed with this robot are shown in Fig. 14. The maximum jump height was more than 0.8 m. The joints showed similar performance to that of the single-legged robot, because they both had the same leg structure. Fig. 14 shows that the pitch angle increased continuously after take-off, which resulted from the deviation between the robot’s CoM and the body’s geometric center. The Swiss Federal Institute of Technology in Zurich (ETH)SpaceBok robot used a reaction wheel integrated inside its main body to adjust its rotation during jumping [30]. In future work,we will implement a posture stabilizer. The jumping experiment results confirm that multiple actuators can be used simultaneously to output explosive speed and torque in the system.Therefore,the proposed explosive electric actuator and the associated control method are suitable for application to the dynamic motion of legged robots.

    Fig. 11. Snapshots of jumping experiment with legged robot. The maximum jump height was 1.5 m.

    Fig. 12. (a) Reduction ratio, (b) torque, and (c) velocity of the first joint actuator during the continuous jumping experiment with a legged robot.

    Fig. 13. Map of absolute values of the speed and torque.

    Provision of a jumping capability is important to improve the performance of humanoid robots in various applications.The Atlas robot, which uses hydraulic actuators, is capable of jumping [4].However, it is difficult for humanoid robots powered by electric actuators to jump,because most of these electric actuators cannot supply the required explosive power.

    We applied the proposed actuator to the hip joints of a humanoid robot to allow it to perform jumping. The robot’s mass was 45 kg, and its height was 1.7 m. Using the characteristics of the proposed actuator, we optimized the robot’s initial posture to maximize the initial acceleration for jumping; we then generated the trajectory of the CoM to make the planned jumping motion more efficient. We considered the full-body dynamics in order to track the trajectory using virtual force control [33]. Snapshots of the jumping experiment performed with this robot are shown in Fig. 15. The jump height exceeded 0.5 m. In the experiment, the initial height of the robot was 1.2 m, and the pitch angle was approximately 27°. The reduction ratio of the hip joint actuator changed from 25 to 20 during the jumping motion. The actuator’s maximum output torque was approximately 252 Nm at the beginning of the jump, and the actuator’s maximum output speed was 117 rpm during the take-off phase. These results confirm that the proposed explosive electric actuator can support a humanoid robot and allow it to perform a dynamic jumping motion.

    5. Conclusions

    Unmanned systems such as legged robots require explosive actuators to perform dynamic motion in complex environments.This paper proposed an explosive electric actuator and an associated control method for legged robots. The proposed highpower-density variable transmission allows continuous and efficient adjustment of the ratio of the speed to the torque output to provide high peak speed or high peak torque at specific moments during dynamic motion. A heat-dissipating structure based on a composite PCM effectively removes the heat that accumulates during high-power operation. The integral torque control method achieves periodic and controllable output power. In the experiments, single-legged, quadruped, and humanoid robots reached jump heights of 1.5, 0.8, and 0.5 m, respectively. These values are the highest reported to date for legged robots powered by electric actuators.

    Fig. 14. Snapshots of the quadruped robot jumping experiment. The maximum jump height was 0.8 m.

    Fig. 15. Snapshots of the humanoid robot jumping experiment. The maximum jump height was 0.5 m.

    Legged robots have various physical forms;hence, it is difficult to design an actuator that will be suitable for all such robots. This paper proposed a general design method to meet the explosive output requirements of most legged robots. This method can be adjusted according to the specific system demands. The actuator characteristics should match the desired system performance.Optimization of the actuator output power for legged robots will be a subject worthy of future study.

    Acknowledgments

    This work was supported by the National Key Research Program of China (2018YFB1304500) and the National Natural Science Foundation of China (91748202 and 62073041).

    Compliance with ethics guidelines

    Fei Meng, Qiang Huang, Zhangguo Yu, Xuechao Chen, Xuxiao Fan, Wu Zhang, and Aiguo Ming declare that they have no conflict of interest or financial conflicts to disclose.

    bbb黄色大片| 色精品久久人妻99蜜桃| 午夜日韩欧美国产| 国产免费现黄频在线看| 午夜免费观看性视频| 午夜影院在线不卡| 久久亚洲国产成人精品v| 黄片小视频在线播放| 1024香蕉在线观看| 亚洲成av片中文字幕在线观看| 亚洲中文av在线| 精品人妻熟女毛片av久久网站| 国产欧美亚洲国产| 国产高清不卡午夜福利| 亚洲欧美精品自产自拍| 日韩熟女老妇一区二区性免费视频| 久久精品人人爽人人爽视色| 免费女性裸体啪啪无遮挡网站| 欧美精品人与动牲交sv欧美| 亚洲精品自拍成人| 69精品国产乱码久久久| 视频区图区小说| 国产国语露脸激情在线看| 亚洲精品久久久久久婷婷小说| 国产一区二区三区av在线| 免费在线观看黄色视频的| 一级毛片 在线播放| 午夜久久久在线观看| 久久久久久久久免费视频了| 免费观看性生交大片5| 国语对白做爰xxxⅹ性视频网站| 精品国产国语对白av| 下体分泌物呈黄色| 日韩中文字幕欧美一区二区 | 夫妻性生交免费视频一级片| tube8黄色片| 少妇 在线观看| 99热全是精品| 女的被弄到高潮叫床怎么办| 午夜福利视频在线观看免费| 午夜免费观看性视频| 啦啦啦 在线观看视频| 国产有黄有色有爽视频| 亚洲精品日韩在线中文字幕| 国产熟女午夜一区二区三区| 日日撸夜夜添| 久久热在线av| 亚洲三区欧美一区| 久久久欧美国产精品| 一级片免费观看大全| 国产男女内射视频| 日韩中文字幕欧美一区二区 | 亚洲七黄色美女视频| 亚洲一级一片aⅴ在线观看| 女人爽到高潮嗷嗷叫在线视频| 亚洲av在线观看美女高潮| 色94色欧美一区二区| 最黄视频免费看| 日韩成人av中文字幕在线观看| 日韩成人av中文字幕在线观看| 中文字幕另类日韩欧美亚洲嫩草| 欧美97在线视频| 在线观看www视频免费| 91成人精品电影| 少妇被粗大的猛进出69影院| 一区二区日韩欧美中文字幕| 男女午夜视频在线观看| 欧美黑人精品巨大| 乱人伦中国视频| 一级爰片在线观看| 另类亚洲欧美激情| 岛国毛片在线播放| 交换朋友夫妻互换小说| 国产精品无大码| 中文字幕色久视频| 91老司机精品| 国产精品嫩草影院av在线观看| 少妇人妻精品综合一区二区| 男女午夜视频在线观看| 亚洲久久久国产精品| 欧美日本中文国产一区发布| 满18在线观看网站| 精品免费久久久久久久清纯 | 国产精品免费视频内射| 18禁观看日本| 另类亚洲欧美激情| 女人久久www免费人成看片| 国产精品偷伦视频观看了| 国产男人的电影天堂91| 国产精品女同一区二区软件| 国产精品久久久久成人av| 黄色 视频免费看| 一区二区日韩欧美中文字幕| 丝袜美腿诱惑在线| 高清av免费在线| 最近中文字幕高清免费大全6| 欧美日韩国产mv在线观看视频| 啦啦啦啦在线视频资源| 在线观看一区二区三区激情| 高清视频免费观看一区二区| 精品免费久久久久久久清纯 | 欧美 日韩 精品 国产| 国产淫语在线视频| 伊人亚洲综合成人网| 亚洲欧洲日产国产| 韩国av在线不卡| 另类亚洲欧美激情| 精品国产一区二区久久| 2021少妇久久久久久久久久久| 国产xxxxx性猛交| 老鸭窝网址在线观看| 国产视频首页在线观看| 老熟女久久久| 国产成人精品久久久久久| 午夜久久久在线观看| 一级黄片播放器| 亚洲国产精品999| 69精品国产乱码久久久| 在现免费观看毛片| 十八禁网站网址无遮挡| 精品一区二区免费观看| 777久久人妻少妇嫩草av网站| 亚洲成人国产一区在线观看 | 亚洲色图综合在线观看| 国产成人系列免费观看| 成人手机av| 中文字幕av电影在线播放| 亚洲少妇的诱惑av| 丝袜人妻中文字幕| 9191精品国产免费久久| 人妻 亚洲 视频| 一区二区三区精品91| 国产av国产精品国产| 女人高潮潮喷娇喘18禁视频| 亚洲av中文av极速乱| 人人妻人人添人人爽欧美一区卜| av在线app专区| 欧美精品人与动牲交sv欧美| 亚洲色图综合在线观看| 国产精品久久久久久久久免| 午夜福利一区二区在线看| 伦理电影大哥的女人| 国产女主播在线喷水免费视频网站| 久久久精品国产亚洲av高清涩受| 一级片'在线观看视频| 精品一区二区三区av网在线观看 | 国产片内射在线| 人妻人人澡人人爽人人| 亚洲专区中文字幕在线 | 日本猛色少妇xxxxx猛交久久| 久久精品久久精品一区二区三区| 侵犯人妻中文字幕一二三四区| 亚洲成人一二三区av| 搡老岳熟女国产| 国产欧美亚洲国产| 婷婷色麻豆天堂久久| 国产97色在线日韩免费| 天堂俺去俺来也www色官网| 伦理电影大哥的女人| 在线观看三级黄色| 狠狠精品人妻久久久久久综合| 免费观看人在逋| 欧美少妇被猛烈插入视频| 老汉色∧v一级毛片| 亚洲成人av在线免费| 国产男女内射视频| 如何舔出高潮| 天天躁夜夜躁狠狠久久av| 观看美女的网站| 女人高潮潮喷娇喘18禁视频| 大香蕉久久成人网| 色婷婷久久久亚洲欧美| 啦啦啦 在线观看视频| 狂野欧美激情性xxxx| 一级黄片播放器| 欧美黄色片欧美黄色片| 大码成人一级视频| 纯流量卡能插随身wifi吗| 亚洲欧美一区二区三区黑人| 日韩中文字幕视频在线看片| 青春草亚洲视频在线观看| 亚洲欧美一区二区三区黑人| 亚洲人成电影观看| 国产精品人妻久久久影院| av国产久精品久网站免费入址| 飞空精品影院首页| 成人午夜精彩视频在线观看| 午夜福利在线免费观看网站| 午夜老司机福利片| 91精品国产国语对白视频| 丰满饥渴人妻一区二区三| kizo精华| 久久天躁狠狠躁夜夜2o2o | 精品一区二区免费观看| 少妇猛男粗大的猛烈进出视频| 欧美 日韩 精品 国产| 日韩,欧美,国产一区二区三区| 国产精品国产三级专区第一集| av卡一久久| 国产精品麻豆人妻色哟哟久久| 汤姆久久久久久久影院中文字幕| 嫩草影院入口| 中文字幕人妻丝袜一区二区 | 在线观看免费视频网站a站| 99香蕉大伊视频| 亚洲精品日本国产第一区| 国产探花极品一区二区| 国产精品 欧美亚洲| 亚洲美女搞黄在线观看| 这个男人来自地球电影免费观看 | 天天操日日干夜夜撸| 综合色丁香网| 80岁老熟妇乱子伦牲交| 亚洲国产欧美在线一区| 国产乱人偷精品视频| 午夜日本视频在线| 免费日韩欧美在线观看| 久久鲁丝午夜福利片| 精品午夜福利在线看| 晚上一个人看的免费电影| 亚洲一码二码三码区别大吗| 国产免费一区二区三区四区乱码| 丝袜喷水一区| 纯流量卡能插随身wifi吗| av一本久久久久| 午夜福利影视在线免费观看| 亚洲精品一区蜜桃| 老司机影院毛片| 亚洲免费av在线视频| 色播在线永久视频| 亚洲美女搞黄在线观看| 久久国产精品大桥未久av| 桃花免费在线播放| 午夜91福利影院| 亚洲图色成人| 人人妻人人澡人人爽人人夜夜| 免费观看a级毛片全部| 成人三级做爰电影| 色婷婷久久久亚洲欧美| 中文字幕人妻丝袜一区二区 | 三上悠亚av全集在线观看| 男女下面插进去视频免费观看| 卡戴珊不雅视频在线播放| 国产精品国产av在线观看| 精品久久久久久电影网| 中文字幕制服av| 久久久亚洲精品成人影院| 咕卡用的链子| 欧美黄色片欧美黄色片| 亚洲一卡2卡3卡4卡5卡精品中文| 亚洲情色 制服丝袜| 国产精品熟女久久久久浪| 久久婷婷青草| 久久免费观看电影| 欧美精品av麻豆av| 一级毛片我不卡| 久久久久久人妻| 久久人妻熟女aⅴ| 夫妻午夜视频| 欧美成人午夜精品| 久久av网站| 1024视频免费在线观看| 久久久国产一区二区| 性色av一级| 亚洲av欧美aⅴ国产| 午夜日韩欧美国产| 国产精品.久久久| 成人18禁高潮啪啪吃奶动态图| 搡老岳熟女国产| 亚洲欧美成人综合另类久久久| 一级黄片播放器| 制服丝袜香蕉在线| 又黄又粗又硬又大视频| 美女脱内裤让男人舔精品视频| 黄色怎么调成土黄色| 国产xxxxx性猛交| 中文字幕另类日韩欧美亚洲嫩草| 欧美在线黄色| 国产女主播在线喷水免费视频网站| 日韩制服骚丝袜av| 丰满少妇做爰视频| 少妇精品久久久久久久| 国产成人精品久久久久久| 久久久久精品国产欧美久久久 | 久久鲁丝午夜福利片| 亚洲国产av影院在线观看| 久久精品国产综合久久久| 在线观看人妻少妇| 大话2 男鬼变身卡| 在线观看国产h片| 久久久久久人人人人人| 成人亚洲欧美一区二区av| 亚洲欧洲精品一区二区精品久久久 | 性色av一级| 欧美精品人与动牲交sv欧美| 一本大道久久a久久精品| 久久久久久久久久久免费av| 黄色毛片三级朝国网站| 大香蕉久久网| 丁香六月欧美| 国产一区二区激情短视频 | av一本久久久久| 美女午夜性视频免费| 日韩一卡2卡3卡4卡2021年| 18禁动态无遮挡网站| 日韩大码丰满熟妇| 亚洲熟女毛片儿| 交换朋友夫妻互换小说| 国产精品嫩草影院av在线观看| 美女脱内裤让男人舔精品视频| 久久韩国三级中文字幕| 成年人免费黄色播放视频| 搡老乐熟女国产| 一区福利在线观看| 2018国产大陆天天弄谢| 精品一品国产午夜福利视频| 91aial.com中文字幕在线观看| 少妇猛男粗大的猛烈进出视频| 欧美国产精品va在线观看不卡| 精品国产国语对白av| 欧美精品高潮呻吟av久久| 在线看a的网站| 国产精品女同一区二区软件| 99久久人妻综合| 99精国产麻豆久久婷婷| 啦啦啦在线观看免费高清www| 国产亚洲一区二区精品| 国产成人精品在线电影| 各种免费的搞黄视频| 久久久久国产精品人妻一区二区| 99国产精品免费福利视频| 日本vs欧美在线观看视频| 欧美精品亚洲一区二区| 捣出白浆h1v1| 各种免费的搞黄视频| 最近2019中文字幕mv第一页| 五月开心婷婷网| 丰满乱子伦码专区| 亚洲美女搞黄在线观看| 伊人亚洲综合成人网| 王馨瑶露胸无遮挡在线观看| 国产在线视频一区二区| 大片电影免费在线观看免费| 男女国产视频网站| 国产av国产精品国产| www.自偷自拍.com| 永久免费av网站大全| 好男人视频免费观看在线| 免费在线观看完整版高清| 亚洲免费av在线视频| 一级黄片播放器| 看十八女毛片水多多多| svipshipincom国产片| 老熟女久久久| 亚洲七黄色美女视频| 亚洲国产中文字幕在线视频| 一级a爱视频在线免费观看| 亚洲中文av在线| √禁漫天堂资源中文www| 韩国精品一区二区三区| 丝袜人妻中文字幕| 中文字幕精品免费在线观看视频| 精品人妻熟女毛片av久久网站| www.精华液| 亚洲av在线观看美女高潮| 欧美日韩成人在线一区二区| 老司机深夜福利视频在线观看 | 久久性视频一级片| 高清欧美精品videossex| 久久精品国产亚洲av涩爱| xxx大片免费视频| 美女视频免费永久观看网站| 亚洲国产欧美一区二区综合| 亚洲国产欧美网| 熟女av电影| 制服诱惑二区| 亚洲精品国产av成人精品| 亚洲在久久综合| 日韩大片免费观看网站| 国产无遮挡羞羞视频在线观看| 免费观看人在逋| 人人澡人人妻人| 亚洲欧美一区二区三区国产| 少妇被粗大的猛进出69影院| 亚洲一卡2卡3卡4卡5卡精品中文| 国产成人免费无遮挡视频| 欧美成人精品欧美一级黄| 中文字幕另类日韩欧美亚洲嫩草| 国产精品人妻久久久影院| 国产黄色视频一区二区在线观看| 亚洲视频免费观看视频| 亚洲国产av新网站| 国产 精品1| 国产男女超爽视频在线观看| 国产一区亚洲一区在线观看| 激情视频va一区二区三区| 国产成人精品久久二区二区91 | 晚上一个人看的免费电影| 久久久久久久久久久久大奶| 亚洲国产欧美网| 免费在线观看完整版高清| xxx大片免费视频| 黄网站色视频无遮挡免费观看| 亚洲七黄色美女视频| 看免费av毛片| 欧美变态另类bdsm刘玥| 大码成人一级视频| 日日啪夜夜爽| 久久精品久久久久久噜噜老黄| 亚洲精品成人av观看孕妇| 国产福利在线免费观看视频| 少妇人妻精品综合一区二区| 一区在线观看完整版| 久久久久久人妻| 操美女的视频在线观看| avwww免费| 亚洲精品国产色婷婷电影| 免费在线观看完整版高清| 精品少妇久久久久久888优播| 国产一区二区激情短视频 | 日日爽夜夜爽网站| 99精国产麻豆久久婷婷| 丝袜脚勾引网站| 纵有疾风起免费观看全集完整版| 一区二区三区乱码不卡18| 国产色婷婷99| 精品亚洲成国产av| 大香蕉久久成人网| 超碰成人久久| 国产av码专区亚洲av| 一二三四中文在线观看免费高清| 美女脱内裤让男人舔精品视频| 色婷婷久久久亚洲欧美| 久久天躁狠狠躁夜夜2o2o | 日本欧美视频一区| 国产精品一区二区在线不卡| 九草在线视频观看| 亚洲综合精品二区| 亚洲激情五月婷婷啪啪| 国产成人欧美| 最近最新中文字幕免费大全7| 久久精品熟女亚洲av麻豆精品| 国产高清国产精品国产三级| 女性生殖器流出的白浆| 高清欧美精品videossex| 电影成人av| 另类精品久久| 亚洲国产av新网站| avwww免费| 两个人看的免费小视频| 亚洲av电影在线进入| 国产精品嫩草影院av在线观看| 亚洲av中文av极速乱| 国产成人欧美| 亚洲成国产人片在线观看| 日韩欧美一区视频在线观看| 观看美女的网站| 午夜福利在线免费观看网站| 欧美日韩av久久| 国产精品无大码| 99久久人妻综合| 啦啦啦在线观看免费高清www| 亚洲精华国产精华液的使用体验| 啦啦啦视频在线资源免费观看| 免费观看人在逋| 97精品久久久久久久久久精品| av免费观看日本| 亚洲少妇的诱惑av| 黑人猛操日本美女一级片| 老汉色av国产亚洲站长工具| 又黄又粗又硬又大视频| 亚洲精品久久久久久婷婷小说| 18禁观看日本| 久久韩国三级中文字幕| 国产有黄有色有爽视频| 亚洲欧美日韩另类电影网站| 香蕉国产在线看| 国产精品久久久久久精品古装| 欧美日韩成人在线一区二区| 免费黄色在线免费观看| 免费高清在线观看日韩| 丝袜人妻中文字幕| 老司机深夜福利视频在线观看 | 成人免费观看视频高清| 欧美另类一区| 国产精品香港三级国产av潘金莲 | 中文字幕色久视频| 精品亚洲成a人片在线观看| 久久久精品国产亚洲av高清涩受| 三上悠亚av全集在线观看| 制服诱惑二区| 国产无遮挡羞羞视频在线观看| 在线观看免费日韩欧美大片| 欧美成人午夜精品| 1024视频免费在线观看| 一级a爱视频在线免费观看| 纵有疾风起免费观看全集完整版| 超碰成人久久| 免费女性裸体啪啪无遮挡网站| 国产1区2区3区精品| 捣出白浆h1v1| 一区二区三区四区激情视频| 久久鲁丝午夜福利片| 丁香六月欧美| 成人亚洲精品一区在线观看| 午夜激情av网站| 中文字幕人妻熟女乱码| 亚洲国产看品久久| 久久97久久精品| 亚洲国产精品一区二区三区在线| 婷婷成人精品国产| 大码成人一级视频| 老汉色av国产亚洲站长工具| www日本在线高清视频| 欧美日韩视频精品一区| 天天影视国产精品| 午夜免费鲁丝| 国产成人精品久久久久久| 妹子高潮喷水视频| 色吧在线观看| 国产成人一区二区在线| 亚洲自偷自拍图片 自拍| 国产黄频视频在线观看| 丝袜喷水一区| 午夜免费鲁丝| 久久99一区二区三区| 国产一级毛片在线| 中文精品一卡2卡3卡4更新| 男女床上黄色一级片免费看| 日本欧美国产在线视频| 69精品国产乱码久久久| avwww免费| 国产成人免费无遮挡视频| av网站免费在线观看视频| 亚洲专区中文字幕在线 | 亚洲国产日韩一区二区| 国产精品久久久久久精品电影小说| 别揉我奶头~嗯~啊~动态视频 | 在线观看人妻少妇| 黄片播放在线免费| 亚洲欧美一区二区三区黑人| 欧美 日韩 精品 国产| 一级片'在线观看视频| 亚洲精品美女久久av网站| 99久国产av精品国产电影| 波多野结衣一区麻豆| 美女午夜性视频免费| av在线播放精品| 欧美精品一区二区大全| 久久人人97超碰香蕉20202| www.熟女人妻精品国产| 成人亚洲欧美一区二区av| 国产精品国产三级国产专区5o| 一级毛片 在线播放| 深夜精品福利| 亚洲精品日本国产第一区| 操出白浆在线播放| 久热这里只有精品99| 亚洲婷婷狠狠爱综合网| 久久99精品国语久久久| 在线观看一区二区三区激情| 久久久久久久精品精品| 亚洲av欧美aⅴ国产| av线在线观看网站| 亚洲欧洲精品一区二区精品久久久 | 日本午夜av视频| h视频一区二区三区| 热re99久久国产66热| 十八禁人妻一区二区| 欧美精品高潮呻吟av久久| av国产精品久久久久影院| 亚洲av欧美aⅴ国产| 亚洲av在线观看美女高潮| 国产日韩一区二区三区精品不卡| 天堂中文最新版在线下载| 纯流量卡能插随身wifi吗| 丰满乱子伦码专区| 精品国产露脸久久av麻豆| 性色av一级| 成人三级做爰电影| 成人亚洲精品一区在线观看| 亚洲熟女毛片儿| 18禁裸乳无遮挡动漫免费视频| 亚洲精品美女久久av网站| 亚洲欧美一区二区三区国产| 国产欧美日韩综合在线一区二区| 国产成人午夜福利电影在线观看| 亚洲自偷自拍图片 自拍| 中文字幕人妻熟女乱码| 国产精品国产av在线观看| 高清欧美精品videossex| 中文字幕人妻熟女乱码| 国产精品国产av在线观看| 中文字幕精品免费在线观看视频| av福利片在线| 国产一卡二卡三卡精品 | 欧美日韩综合久久久久久| 建设人人有责人人尽责人人享有的| xxx大片免费视频| 色94色欧美一区二区| 久久久精品区二区三区| 国产精品免费大片| 99国产综合亚洲精品| 女人被躁到高潮嗷嗷叫费观| svipshipincom国产片| 中文字幕人妻丝袜制服| 999久久久国产精品视频| 成人18禁高潮啪啪吃奶动态图| 亚洲av日韩在线播放| 乱人伦中国视频| 黄色怎么调成土黄色| 麻豆av在线久日| 国产日韩欧美在线精品| 丝袜美足系列| 中文欧美无线码|