• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Effects of Ca content on the activity of HZSM-5 nanoparticles in the conversion of methanol to olefins and coke formation

    2021-11-20 08:33:16GHAEDIMohammadIZADBAKHSHAli
    燃料化學(xué)學(xué)報(bào) 2021年10期

    GHAEDI Mohammad ,IZADBAKHSH Ali

    (Department of Chemical Engineering, Faculty of Petroleum, Gas and Petrochemical Engineering, Persian Gulf University,Bushehr P.B. 75169-13817, Iran)

    Abstract: Effects of calcium content on the performance of HZSM-5 nanoparticles of 150 nm with Si/Al ratio = 230 in the methanol to olefin conversion were investigated. The parent and modified catalysts showed their largest yields of ethylene and propylene at 490 °C and lower WHSV (= 3.3 h?1). The selectivity for propylene over HZSM-5 was 0.45 at 490 °C whereas it was promoted to 0.51 over Ca27-HZSM-5 (Ca/Al = 27). With decreasing temperature from 490 to 440, and 390 °C, the yield of propylene and ethylene remained nearly constant at 0.13?0.14 and 0.10?0.11 over Ca27-HZSM-5, respectively; more narrow than the corresponding range of yields for HZSM-5 (0.10?0.14 and 0.08?0.12). FT-IR results confirmed the formation of oxygenated and poly alkyl aromatic species in the carbon deposits. TG results indicated that oxygenate coke was formed and converted to heavier poly aromatic coke species with time. Increasing Ca in the porous structure of HZSM-5 may lead to heavier aromatic carbonaceous deposits. In general, Ca content positively affected activity through modification of the density, strength, and accessibility of Br?nsted and Lewis acid sites. Long-term MTO activity test of HZSM-5 with Ca/Al =27 showed stable performance over 100 h, although with an oscillatory feature.

    Key words: ZSM-5;zeolite;MTO;catalyst;reaction;nano

    Methanol to olefin, MTO, indirectly converts natural gas to a feedstock of the petrochemical industry by providing light olefins. MTO provides a new promising route to fill the increasing gap between supply and demand of propene through conversion of a non-oil resource[1]. The UOP/Hydro MTO process, the Lurgi process, and the DMTO (methanol or DME as feedstock) process are the major licensed available MTO technologies[2?5], at the present time.

    The first commercial scale installation of the UOP/Hydro MTO process was announced in 2011, and was planned to be in operation in 2013[6]. Honeywell UOP has its own MTO technology which now operates as Jiangsu Sailboat Petrochemical[7]with a production capacity of 833000 metric tons per year as the largest single-train MTO unit in the world. The methanol feed was obtained from domestic coal.

    Lurgi has specifically dedicated the methanol to propene, MTP, process with no ethylene product[2].This company uses zeolite HZSM-5 as the catalyst to carry out this process. The key advantage of HZSM-5 is the longer lifetime of this zeolite against the SAPO-34 being used in MTO as a UOP’s proprietary catalyst[8?13]. Researchers have focused on the improvement of coking and selectivity to light olefins over both catalysts[14]. Methanol converts to light olefin in an acid catalyzed route which is controlled by zeolite acidity and shape selectivity[9,15 ?22]. Particle size control and hierarchical pore structure affects the catalytic performance of zeolites in MTO reaction[14,23,24]. Metal incorporation in the zeolite structure is the one of routes to modify catalyst acidity with possible steric hindrance effects[25?30]. Experimental studies have proved the positive effect of reducing the acidity level of the HZSM-5 zeolite on catalyst stability and selectivity to light Olefins[15]. The regions of strong acidic sites produce a rather large amount of aromatic compounds increasing the formation of carbon deposits in the pore structure of the zeolite[16,17].

    The incorporation of metal cations into the zeolite structure replaces protons of bridging hydroxyls,turning the Br?nsted acid sites to Lewis ones. The substitution of aluminum for silicon in a silica covalent framework leads to a charge unbalance which must be compensated by extra framework cations, mainly alkaline. Alkali and alkali earth cationic zeolites are used mainly as adsorbent for industrial gas purification,e.g. CO2, to modify membrane matrix, and as ion exchangers for water softening. Basic property of alkali and alkali earth cationic zeolites renders these materials as potential basic catalysts[31].

    Cations possess determined locations in the pore structures of zeolites. For example, half of Na+in Namordenite with a 12-membered elliptical Si?O rings are located in the middle of the small channels of compressed 8-membered rings in the site called (I)which is not supposed to be available to CO, CO2and pyridine. The other half of Na+ions are distributed between site IV, near the opening of the side pocket in the main channels made up by 12-membered rings and in the position VI, which is well inside the main channels near to five-membered side rings[31]. Different positions of cations or protons could result in different acidic strengths of these sites.

    Olefins are produced on the acidic molecular sieves in MTO through a well-accepted hydrocarbon pool mechanism first proposed by Dahl et al[32?34],which means hydrocarbon intermediates after formation react with methanol leading to release of light olefins and other products from the intermediate species. Two cycles have been proposed on HZSM-5 in the MTO reaction[35]. In the olefin-based cycle,oligomerized olefins by methylation of C3+alkenes are active intermediates[36,37] from which mainly olefin products form by cracking. This route is most favored on the acidic sites located over the channel walls in the pore structure of zeolites, producing predominantly[38]to propene and higher alkenes and significantly less carbonaceous deposits. The aromatic-based cycles,polymethylbenzenes and polycyclic aromatic as main intermediates[39,40] are methanol methylated and olefin released by elimination via side-chain and paring routes[41,42]. The aromatic-based cycle requires more space to form bulkier branched polycyclic intermediates. Therefore, acid sites located in the intersections of 2D sinusoidal and 1D straight channels,where cavities of 0.9 nm being formed, favors aromatic-based cycle which produces mainly[38]ethene,propene, and aromatics.

    Taking into account above observations,redistribution of acid sites can regulate the dual-cycle hydrocarbon pool mechanism. Cation incorporation can be regarded as a synthesis strategy to tune the ratio of Lewis to Br?nsted acid sites and redistribution of their locations.

    It is also reported that concentration of Lewis and Br?nsted acid sites on the zeolite can provide a synergistic effect on MTO product distribution through modification of hydrogen transfer rate.

    The exchange of cations of alkaline earth and rare earth elements would decrease the overall acid strength of zeolites. The resulting Lewis acid sites, LAS, are generally weaker than the bridging Br?nsted acid sites,BAS, in zeolites. This may decrease hydrogen transfer of exchanged zeolite which can diminish the cyclization and dehydrogenation, leading to less formation of alkanes and aromatic species[43,38]. Two routes have been suggested for the formation of alkane and aromatic species in MTO over HZSM-5 via hydrogen transfer (HT), i.e. methanol-induced HT and olefin-induced HT[44]. The former is affected by both BAS and LAS while the latter is driven by BAS[44].Therefore, increase in LAS concentration induces a higher rate of the former route but does not promote HT reactions between olefins as reported for MTH conversion on HZSM-5. It should be noted that this conclusion was only obtained for Al-related LAS, and cannot be extended to other metal LAS formed by cation exchange[44].

    Moreover, the Aluminum coordination state in the zeolite framework could affect the MTO reaction. The synergy of extra framework Aluminum (EFAl) and Br?nsted acid sites in zeolite catalysts was shown to change the reaction pathway, leading to significantly reducing the activation barrier of the initial C?C bond formation and accelerate the MTO reaction[45].

    Chemical modification of HZSM-5 by boron has been reported to increase the selectivity of propene by 48% and the lifetime of the catalyst by up to four times[16]. La and P incorporation to HZSM-5 (P-La-ZSM-5) increased catalyst lifetime from 126 to 188 h,as well as the overall catalyst selectivity[25].Modification of HZSM-5 by Iridium led to the 8%increase in the selectivity of propene as well as lifetime of the catalyst[26]. The performance of Fe-incorporated HZSM-5 indicated the increase in the selectivity of propene up to 6%[27]. The tuning of Si/Al in HZSM-5 by Fe isomorphous substitution exhibited a linear relation between the density of acid sites with selectivity to C2?C4light olefins[28]. In a comprehensive study, Liu et al. modified the HZSM-5 catalyst with a Si/Al ratio of 220 by elements such as P, Ce, W, Fe,Mn, Gr, Mo, Ga, V and Ni. Their results showed that the selectivity to propene over P-HZSM-5 increased from 46.4% to more than 65.6%. The selectivity of propene after 3 h of reaction for different modifying elements has been reported as P > Ce > W > Mn > Fe >Gr > Mo > Ga > V > Ni[29].

    Al-Jarallah et al[30]reported that the Ca modified HZSM-5 exhibited the highest light olefin selectivity among various metals impregnated. Results of Zhang et al[46,47] indicated that the performance of Ca-modified HZSM-5 in methanol to propylene reaction improved and the selectivity for propylene increased to 50%.This observation was explained by reducing the strong acid sites due to their interactions with Ca and the formation of Zeo-Ca-OH. They also investigated the effect of Ca content on the performance of HZSM-5 with Si/Al ratio = 96 in the MTO conversion at methanol WHSV = 2.1 h?1. The size of catalyst particles was not reported. The optimum Ca content was determined = 6%, considering the aspects of stability (< 40 h) and light olefin’s selectivity (70%?80%). In another study of the effects of Ca incorporation to HZSM-5 structure with Si/Al = 40,samples of Calcium loaded-HZSM-5 (Ca = 6%)prepared using different methods, were tested in MTO reaction att= 500 °C and methanol WHSV = 8 h?1[48].Suppression of aromatic cycle in MTO reaction network by Ca incorporation, leading to longer life time (60 h) and higher selectivity to propylene (55%),was proposed. The superior catalytic activity of nanosized particles of ZSM-5 zeolite was reported[24]. The positive effect of nano-sized ZSM-5 particles on the selectivity of propylene and catalyst life time in MTO reaction has been reported[14,23]. In this paper, the investigation of the effect of the incorporation of different content of calcium ions into nano-sized particles of HZSM-5 of high Si/Al (≈ 230) ratio with a hierarchical porous structure on the catalytic performance in MTO conversion is reported. In fact,the effect of Ca incorporation at the conditions of nano size of HZSM-5 particles and high Si/Al ratio favoring larger selectivity to light olefins and longer life time in MTO would be investigated.

    1 Experimental

    1.1 Material

    Sodium aluminate (NaAlO2> 98%) and tetrapropyl ammonium hydroxide (TPAOH) [(C3H7)4NOH 1 mol/L solution] were purchased from Sigma Aldrich company.Tetraethyl ortho silicate (TEOS) [Si(OC2H5)4> 98%]was purchased from Acros company. Sodium hydroxide(NaOH > 98%), Ammonium nitrate (NH4NO3> 99%)and synthesized calcium nitrate were prepared from the Merk company. Ethanol (C2H5OH > 96%) was obtained from a domestic company.

    1.2 Nanocatalyst preparation

    To synthesize nano-sized ZSM-5 particles, the similar synthesis procedure reported elsewhere[49]was followed. In a typical synthesis, 34.4 mL of water was initially mixed with 0.014 g NaOH and stirred. 0.043 g of sodium aluminate (NaAlO2) was added to this solution. After complete dissolution of sodium aluminate in NaOH solution, 12.3 g of tetra-propyl ammonium hydroxide was added to the solution. After adding TPAOH, the solution was stirred at 25 °C for 2 h.Then, the amount of 23.25 g of 96% ethanol was added to the solution and allowed to be well mixed with the initial solution. At this stage, the pH of the solution was 12.3. In the next step, the amount of 25.1 g of tetraethyl ortho silicate was added dropwise to the previous solution under vigorous stirring. The molar composition of the resulting mixture was:

    1.44 TPAOH: 0.03 Al2O3∶13.8 SiO2∶222 H2O∶56.6 EtOH∶0.05 Na2O.

    After stirring at 25 °C for 30 min, the gel mixture was refluxed without stirring at the temperature of the oil bath = 100 °C for 60 h. The solid white zeolite was separated by centrifuge, washed four times with DM water and dried in the oven at 105 °C overnight completely. The dried zeolite powder was calcined at 550 °C for 10 h with the ramp of 2.5 °C/min.

    1.3 Ion exchange

    The obtained Na-ZSM-5 zeolite was converted to the HZSM-5 by means of the ion exchange process.For this process, a solution of 1 molar ammonium nitrate was prepared and 20 mL of this solution was used per gram of catalyst. The catalyst suspension was stirred at 80 °C for 2 h followed by centrifugal separation of solid product. This step was repeated three times, and then the drying step was carried out at 90 °C overnight. The dried powder catalyst was then calcined again at 550 °C for 6 h with the ramp of 2.5 °C/min.

    1.4 Impregnation

    Predetermined volumes of 0.1 mol/L calcium nitrate solution were added to a specified amount of obtained solid product to adjust the composition of the final product to the Ca/Al ratios of 9, 27, 54. After stirring at 25 °C for 24 h, washing and centrifuge, the solid product dried at 90 °C overnight. The obtained powder was then calcined at 550 °C for 6 h with the ramp of 2.5 °C/min.

    1.5 Material characterization

    1.5.1 Low angle X-ray diffraction measurement

    Powder XRD spectra of synthesized nanocatalyst samples were recorded by the diffractometer Philips PW1730 that uses CuKα1 radiation (λ= 1.5406 ?)with the power of 1200 W (40 keV) to perform analysis with the 2θscanning from 5°?90° at the step size of 0.05°.

    1.5.2 Surface area analysis

    The surface areas of the catalysts were determined at ?196 °C by surface analyzer micromeritics ASAP 2020. The specific surface area and porosity were calculated based on Brunauer-Emmett-Teller (BET)andt-plot models. The device measures the adsorption and desorption of nitrogen gas by the sample at a constant temperature of liquid nitrogen to determine the surface area and porosity. Prior to N2adsorptiondesorption process, the samples were degassed at 350 °C for 4 h.

    1.5.3 Field emission scanning electron microscopy

    (FESEM)

    FESEM images and EDX spectrum were used to verify the formation, morphology and composition of nanoparticles. SEM images were obtained by TESCAN MIRA3 instrument with the EDX spectra recorded at the accelerating voltage of 15 kV and the beam current of 10 nA.

    1.5.4 Fourier transformed infra-red

    FT-IR spectra of fresh and coked samples were recorded on a Testscan Shimadzu FT-IR 8000 series spectrometer using the KBr pellet technique with the wavenumber range of 400?4000 cm?1.

    FT-IR absorption of pyridine adsorbed samples were taken on JASCO FT-IR-4600 type A, with standard light source detector TGS, Resolution of 4 cm?1, scanning speed of 2 mm/s in 1300?1700 cm?1.Pyridine adsorption was performed for 24 h after drying the sample at 120 °C overnight, kept away from air moisture using silica gel prior to pyridine adsorption. A home-built system was used for simultaneous contacting four isolated samples with pyridine vapor in argon for pyridine adsorption.Samples were kept in silica gel desiccator before FT-IR absorption test.

    1.5.5 Temperature programmed desorption (NH3-TPD)

    The temperature programmed desorption analysis was performed by using reaction setup connected to the required gas supplies and a TCD detector. In a typical TPD analysis, an amount of 0.10 g of calcined sample packed in a quartz U-tube between quartz particles,0.2 g in each side, was degassed by heating up to 250 °C at the temperature ramp of 10 °C/min and hold time of 1 h, followed by cooling to 100 °C in 2 h under argon flow of 30 mL/min. The absorbing basic Ammonia mixture gas stream (5% NH3in He) was introduced to the sample at the flow rate of 40 mL/min for 15 min.Then, the sample was purged under Helium flow of 30 mL/min for 50 min. During purge time, the TCD detector was turned on and the baseline of the detector signal was stabilized. Helium flow rate was turned to 30 mL/min and the sample was heated to 700 °C with the rate of 10 °C/min. The desorption profile was obtained from the TCD signal recorded during the heating period.

    1.5.6 Thermogravimetric analysis (TGA)

    About 5 mg of the prepared zeolites were loaded in a TA Instruments SDT-Q600 to measure TGA profiles. A stream of Air was introduced to the zeolite sample being heated up to 650 °C with the temperature ramp of 10 °C/min.

    1.6 Reaction setup

    In the experimental reaction set-up, catalytic reaction was carried out inside a quartz U-shaped tube reactor placed in an electric furnace, connected to gas chromatograph at the outlet for online product analysis.In each experiment 0.2 g of catalyst particles of size 1?1.5 mm, were placed in a quartz U-tube with inner diameter of 5 mm and then the catalyst bed was heated up to 490 °C for 1 h under Argon flow = 20 mL/min controlled by a MFC. A bottle of liquid methanol stirred at 650 r/min and 45 °C was bubbled via an Argon stream of 20 mL/min at the atmospheric pressure to obtain the methanol WHSV = 5.55 h?1in the catalyst bed. The mixed feed stream was directed to the quartz U-tube at 490 °C through a heated line and was allowed to contact the catalyst bed for at least 2 h.Afterwards, the reactor test was continued for each catalyst at the lower temperatures of 440 and 390 °C.Finally, the furnace was reheated to 490 °C and argon flow reduced to 10 mL/min in order to compare the performance of the catalyst sample at the methanol WHSV = 3.27 h?1. Product flowed out of a quartz Ushape reactor passing through a heated line after which the product stream was condensed at room temperature.The weight and density of the liquid product was measured. The density and GC analysis showed it mainly composed of unconverted methanol and water.

    Long term performance tests were carried out on the 0.1 g of catalyst particles with a methanol bubbler using argon flow rate = 20 mL/min at the methanol WHSV of ca. 7.5 h?1. Gas products were analyzed online by Gas Chromatograph (Agilent 7890 A)equipped with a FID detector and HP-Plot Q capillary column (30 m × 0.53 mm × 40 μm) under He carrier flow. In each GC analysis of product samples, the oven temperature was held constant at 60 °C . The temperatures of injection inlet and FID detector were set to 250 and 300 °C, respectively.

    2 Results and discussion

    2.1 XRD results

    The XRD patterns of the prepared samples were presented in Figure 1. All diffraction peaks appeared in the expected 2θdegree confirming the formation of MFI-structure of ZSM-5 for all sample powders.Calcium added to the structure of ZSM-5 did not form a nano cluster on the external surface of zeolite particles as there was no relevant impurity reflection in the XRD patterns. Moreover, as shown in Figure 1, the intensity of the diffraction peaks of modified catalysts was reduced, which may indicate the incorporation of metals into the microporous structure of zeolites.

    Figure 1 XRD patterns of the prepared samples

    2.2 Surface analysis

    N2adsorption-desorption isotherms of the prepared catalysts were given in Figure 2. The sharp increase of adsorption of N2over the samples at the lowp/p0confirmed the formation of a microporous zeolite material. Samples exhibited a type-IV isotherm with two hysteresis loops at relative pressures higher thanp/p0≥ 0.3 and 0.5, indicating existence of mesopores.These hysteresis loops (H3 type) are usually associated with capillary condensation in mesopores.

    Figure 2 N2 adsorption-desorption isotherms of the prepared catalysts

    The micropore size distribution plot obtained viat-plot method using HJ model was given in Figure S1(a) of the supplementary material file. The parent HZSM-5 showed the largest adsorption capacity. Ca27-HZSM-5 and Ca54-HZSM-5 samples presented the highest and the lowest surface area among the calcium modified zeolites, respectively.

    In Table 1, the results of pore size and specific surface areas of the synthesized samples were presented. It is observed that by the incorporation of metal species to the catalysts, the specific surface areas of the catalysts were reduced. This result indicated that the pores volume has been occupied by the metal atoms with the incorporation of the metals, at least to some order. The micropore volume of Ca9-HZSM-5 and Ca54-HZSM-5 decreased to about 0.05 from 0.07 cm3/g in the parent HZSM-5 as a result of metals incorporation inside their micropore volume of crystalline structure. Ca27-HZSM-5 presented more micropore volume respect to the other two Ca incorporated HZSM-5 zeolite.

    According to the data in Table 1, the size of micropores of maximum distribution in the parent HZSM-5 was 0.5 nm, which increased with Ca incorporation as the corresponding pore sizes increases to 0.52 and 0.55 nm in Ca27-HZSM-5 and Ca54-HZSM-5 catalyst, respectively. The micropore size enlargement is a result of BET model to fit the reduced pore volume measured.

    Table 1 Pore structure properties of the prepared catalysts obtained from N2 Adsorptive isotherm

    Two flat and wide hysteresis loops[50]can be observed in the N2isotherms of Figure 2 can be attributed to slit mesopores pores or ink-bottle-shaped mesopores with small openings, or it can be due to the effect of a pore network. These mesopores, pore size distribution shown in Figure S1(b) probably were formed due to the silicon dissolution in the course of synthesis of the parent HZSM-5. Two mesopore sizes,given in Table 1, were measured for each sample. The larger mesopore of samples provides the insignificant mesopore volume respect to the smaller pore size. The calculated N2adsorption capacity of the metal-modified HZSM-5 catalysts were less than that of the parent HZSM-5, probably due to the reduced crystalline order in the samples, cage size, and/or pore blockage as a result of metal incorporation.

    2.3 SEM analysis

    The SEM images of catalyst powders were shown in Figure S2. As it can be observed in the images, the crystal particles are interconnected agglomerates of nano (sub-micron) size in the range of 100?200 nm with nearly spherical shape. No distinct difference in the morphological properties of particles of the prepared samples can be observed. Hence, Ca impregnation didn’t lead to distinct morphological effects on the HZSM-5 particles. It is a desirable feature to compare the MTO performance of the prepared samples without the concern of probable effects of physical properties of samples particles such as their size or shape on their catalytic performances.

    In Table 2, composition data of the synthesized samples obtained by EDX spectroscopy were given.According to the results, Al content of samples was less than 1% as the target value of Si/Al in the synthesis procedure is as large as 230. Despite the low accuracy of EDX results for low content element in the samples, i.e. calcium content, the expected increasing trend of Ca content values of samples was followed.The calculated Ca/Al ratios for CaX-HZSM-5 (X= 9,27, 54), given in Table 2, equal 5.7, 19, and 34,respectively.

    Table 2 Elemental composition of the prepared catalysts obtained from EDX spectra

    2.4 FT-IR results

    FT-IR spectra of the prepared catalysts were recorded in the range of 400?4000 cm?1, as shown in Figure S3. The band around 450 cm?1represents the Si?O?Si bending vibration of the five-membered rings in the zeolite framework[51]. The absorption band about 550 cm?1was assigned to the external symmetric stretching vibration of the five-membered rings in MFI zeolites[51?54].

    The absorptions band at 800 and 1100 cm?1appeared due to the asymmetric stretching of external and internal linkages, respectively[52,53].

    The peak at 875 cm?1, appeared and intensified with the Ca content in the modified zeolites, could be attributed to the Ca?O vibrations. It could be considered as an indication of Ca incorporation in the structure of HZSM-5.

    Yarulina et al[48]calculated that OH stretching frequency of HZSM- 5 at 3684 cm?1shifted upwards to 3848 and 3796 cm?1for the straight and curled Ca chains (CaOCaOH+) in the Ca-ZSM-5 catalyst.Therefore, the absorption at 3840 cm?1could be assigned to stretching vibration of straight Ca chain in the Ca-exchanged HZSM-5 catalysts.

    Look, she said softly, her eyes directing me to a spot on the floor beside the dresser. To my amazement19, there, as if it had never been removed, stood the old pickle jar, the bottom already covered with coins.

    To evaluate the distribution of BAS and LAS in the synthesized zeolites, samples are first dried in 120 °C and then treated with pyridine vapor at room temperature for 24 h. Samples were stored in the dry Argon atmosphere prior to analysis. According to the literature, the lone pare orbital of adsorbed pyridine would interact with Lewis acid sites absorbing FT-IR at 1456 and 1510 cm?1, which BAS shift this absorption band to higher FT-IR frequencies, i.e. 1545 and 1645 cm?1, respectively[63]. Thus, as it is common, two bands at 1456 and 1545 cm?1were selected to calculate LAS and BAS percentage in the prepared zeolites. Two broad peaks were clearly detected in 1700?1300 cm?1from which the band in 1580?1380 cm?1was chosen for calculation of acid site distribution. This vibration band in FT-IR spectra of pyridine adsorbed samples are plotted in the supplementary material file as Figure S4 as well as the deconvoluted peaks. Bands at 1456 and 1545 cm?1were plotted with thick dashed lines to be recognized from other bands. The remaining bands would be related to other vibrations of chemically or physically adsorbed pyridine.

    The center of deconvoluted peaks and their area,the calculated BAS/LAS ratio and LAS percentage were reported in Table 3. BAS vibration peak of Ca9-HZSM-5 showed a shift to lower wavenumbers of pyridine adsorbed on BAS (1547 => 1540 cm?1) with respect to other catalysts, indicating weaker interaction of adsorbed pyridine with BAS in Ca9-HZSM-5. It could be considered as a decline in the BAS strength of Ca treated HZSM-5 at Ca/Al = 9. No significant shift of vibration wavenumber of adsorbed pyridine on Lewis acid sites of the prepared catalysts was observed.At Ca/Al = 9, the BAS site of zeolite constitutes the major part (≈ 70%) of acid sites while the LAS are in the majority (≥ 78%) in the prepared zeolites at Ca/Al ≥ 27. The decline of strength of Br?nsted acid sites up to a Ca content followed by their strength enhancement with further Ca incorporation could be assumed. It implies that BAS strength is dependent on the concentration of near LAS sites. It seems that high concentration of LAS leads to loss reducing effects on BAS strength, which may be caused by directional removal or strengthening of polar forces. Such a trend was exactly observed in TPD data, explained in the next section.

    Table 3 Center area of FT-IR BAS and LAS peaks of FT-IR spectra of pyridine-adsorbed catalysts and their distribution

    The calculated percentage of LAS in the prepared catalysts show a direct relation between Ca/Al ratio of synthesis and their calculated Lewis acid site percentage. It is noteworthy that the variation of acid site distribution nearly loses its dependence on Ca content after Ca/Al = 27. EDX data confirmed that Ca content of Ca54-HZSM-5 is near to 3 times of Ca27-HZSM-5. A larger increase of LAS percentage in Ca54-HZSM-5 with respect to Ca27-HZSM-5 is expected. It seems that steric limitations imposed by Ca cations on pyridine molecules prohibited their diffusion to Lewis acid sites placed in the most inner parts of catalyst particles.

    2.5 NH3-TPD results

    The acidic properties of the Ca incorporated HZSM-5 catalysts as well as the parent HZSM-5 catalyst were studied by NH3-TPD technique and the obtained desorption profiles were displayed in Figure 3.The NH3-TPD profiles were deconvoluted to three or four NH3desorption peaks, including the first peak around 160 °C, the second one in the range of 358?426 °C, and the third one in the range of 408?575 °C.The first resolved peak was related to the physisorbed NH3. The second peak was related to terminal ?Al?OH and ?Si?OH and ?Ca?OH as weak Br?nsted acid sites.The last resolved peak around 500 °C was assigned to strong Br?nsted bridging OH (Al?OH?Si) or Ca related Lewis acid sites. The area of the last two peaks of Ca incorporated zeolites strongly increased.Therefore, the Ca associated adsorbed ammonia must account for a significant portion. Br?nsted acid sites convert to Lewis acid sites with incorporation of Ca cations in HZSM-5 structure, as previously reported[48].

    Figure 3 NH3-TPD profiles of HZSM-5 and Ca incorporated HZSM-5 zeolites

    Maximum temperature, area and height of deconvoluted peaks in the NH3-TPD profiles of the prepared catalysts were presented in Table 4. The height of peaks was used for comparing the density of corresponding acid sites because the resolved peaks are broad and overlapped.

    Table 4 Maximum temperature, area and height of deconvoluted peaks in the NH3-TPD profiles of the prepared catalysts

    According to the data in Table 4, Si?OH, Al?OH(small share due to low Al concentration), Ca?OH acid sites (2thpeak) were appeared in the TPD profile as a peak with the center around 358?426 °C with the following order of height size in the prepared zeolites:

    Ca27-HZSM-5 > Ca54-HZSM-5 > Ca27-HZSM-5 > HZSM-5

    Si?OH?Al and Lewis acid sites (3thpeak) were appeared in the TPD profile as a peak of centerline at about 408?575 °C with the following order of height size

    Ca27-HZSM-5 > Ca9-HZSM-5 > HZSM-5 > Ca54-HZSM-5.

    Although, the height and area of the second and third peaks varied considerably, it cannot be related directly to the density of weak or strong acid sites.Theoretically, the Ca cation incorporated should replace two protons meaning that a LAS replaces two BAS. Hence, a decrease of total density of acid sites should be expected. However, the TPD profiles of Ca incorporated zeolites showed increased adsorbed ammonia. One explanation could be the possibility of multiple adsorption of ammonia on Ca Lewis acid sites rather than single adsorption by OH group.

    FT-IR spectra of pyridine adsorbed samples indicated decrease of BAS strength along with no change of LAS strength. This observation may explain the initial shift of the third TPD peak to lower temperature at Ca/Al = 9 followed by strength recovery of the corresponding acid sites at Ca/Al = 27.Considering the larger portion of LAS in Ca27-HZSM-5, the effect of weakened BAS on peak shift decreases with Ca content. Hence, the third peak shifts back to higher temperature, though still lower than that of the parent zeolite.

    The weak Br?nsted acid sites accounted for the 2ndNH3desorption peak originated from terminal OH, i.e.Al?OH, Si?OH, or Ca?OH, respectively.

    The 3thpeak in the NH3-TPD spectra was assigned to the adsorption of NH3onto strong acid sites resulting from bridging OH (Si?OH?Al), extra-framework Al and Ca as Lewis acid sites.

    It is obvious from Figure 3 that Ca incorporation in Ca9-HZSM-5 and Ca27-HZSM-5 has resulted in at least two different Ca related acid sites participating in ammonia adsorption at different strengths. It is noteworthy that intensification of the second and third peaks accompanied with a downward shift of their maximum temperature, showing decline of the relevant acid strength.

    NH3-TPD data can be summarized as follows. The second Peak in TPD profiles grows in Ca/Al ratios of 9 and 27 due to increase of Ca?OH while its centerline shifts to lower temperatures with respect to that of HZSM-5 catalyst indicating less Br?nsted acid strength of Ca?OH than Si?OH or Al?OH.

    The third peak includes both bringing OH sites and LAS. Its area grows for samples of Ca/Al ratios = 9 and 27 as its centerline shifts to lower temperatures at Ca/Al ratio = 9 and shifts back to higher temperature again at Ca/Al = 27. FT-IR data of pyridine adsorbed samples confirmed such a variation of strength in BAS sites. Considering the significant portion of Ca LAS in the third peak in the Ca incorporated zeolites, the strength of their LAS should be less than original BAS in the parent HZM-5. Both LAS and BAS are almost inaccessible to ammonia in TPD analysis of Ca54-HZSM-5 catalyst. It seems ?Ca?OH, mostly on the external surface (peak center at 358 °C), has remained accessible in the TPD experiment on Ca54-HZSM-5.

    2.6 MTO performance tests

    Table 5 shows the results of catalytic performance including the calculated values of methanol conversion,selectivity and yield of ethylene and propylene for the prepared catalysts at the different operating conditions.The MTO performance data of the prepared catalysts are also shown in Figures 4?5 and Figure S5 in the supplementary material file. As expected, the highest methanol conversions were observed in the reaction at the highest temperature, i.e. 490 °C, and the lowest methanol WHSV, i.e. 3.3?4.0 h?1.

    It can be observed from data in Table 5 which are also plotted in Figure 4?5 and Figure S5, methanol conversion increases with temperature for all catalyst samples. At the higher temperature, methanol converts faster to products leading to the higher conversions for the prepared catalysts. According to Figure 5(a), (b),the selectivity to ethylene and propylene samples increases with temperature over all catalysts. The yield of product species (Yi), the ratio of molar flow rate of product species (Fi) per molar flow rate of methanol feed (Fmethanol,in), calculated by the multiply of methanol conversion and selectivity of species (si=niFi/(Fmethanol,in?Fmethanol,out)), i.e.Yi=Fi/Fmethanol,in, provides a certain comparative performance variable among a set of catalysts.nidenotes the number of carbon atoms in one molecule of species. According to data plotted in Figure 5(a), (b), the yield of both ethylene and propylene enhances with temperature.

    Figure 4 Methanol conversion versus temperature for the prepared catalysts in the MTO conversion, p = 100 kPa,methanol WHSV = 8 and 4 h?1, argon flow = 20 mL/min

    Figure 5 Light olefin yield versus temperature for the prepared catalystsintheMTOconversion, p =100kPa,metha nolWHSV =8and4h?1,argon flow=20mL/min;(a): ethylene; (b): propylene

    Figure 6 Methanol conversion and selectivity of olefins versus time for the prepared catalysts in the MTO conversion,p = 100 kPa, catalyst weight = 0.1 g, argon flow = 20 mL/min, regenerated HZSM-5 was used in this test which its initial conversion (57%) is less than that of fresh sample (79%) the HZSM-5 catalyst in this test was regenerated at 650 °C for 5 h

    Table 5 Methanol conversion, selectivity and yield of ethylene, propylene and C2?C4 olefins obtained by the prepared catalysts at the different reaction temperatures and space velocities of methanol feed stream

    Ca54-HZSM-5 with the lowest methanol conversion, is the most selective catalyst toward propylene meaning that less conversion of methanol favors propylene production. The TPD profile of Ca54-HZSM-5 showed reduced ammonia adsorption which was related to the diffusion barrier induced by populated Ca cations inside pore structure. The highest LAS content with limited accessibility led to the lowest conversion with highest propylene selectivity.

    According to a relevant study[48], Ca incorporation into HZSM-5 with Si/Al = 46 (1 < Ca/Al < 6) improved the selectivity to propylene in MTO reaction in the expense of ethylene selectivity. In this study, the decline of strength of acid sites and suppression of hydride transfer and oligomerization reactions on significantly weaker acid sites were suggested as the reasons for the effect of Ca incorporation, i.e.diminishing aromatic cycle and lowering ethylene selectivity. However, our data did not show a trade-off between selectivity to ethylene and propylene. It should be noted that the catalysts synthesized in our study are of higher Si/Al (≈ 200) and Ca/Al (> 9) ratio with nano-sized particles (≈ 150 nm).

    Data in Table 5 shows that the performance of Ca27-HZSM-5 and Ca54-HZSM-5 catalysts with respect to the yield of light olefins is nearly independent of temperature very clearly. With decreasing temperature from 490 to 390 °C and at the methanol WHSV of 5.55 h?1, the yields of ethylene and propylene on Ca27-HZSM-5 remained nearly constant in the ranges of 0.10?0.11 and 0.13?0.14, respectively. The other catalysts showed an intense decline in their performance at 390 °C. Ca54-HZSM-5 catalyst presented the lowest methanol conversion even at 490 °C and WHSV = 3.3 h?1while other catalysts are much more active at this condition. Increasing Ca content of HZSM-5 at Ca/Al = 27 and 54 reduced methanol conversion but independent of temperature with overall enhanced yield of ethylene and propylene. It indicates a lower activation energy barrier of MTO reactions on the Ca LAS with respect to the BAS. Further increase of Ca content in HZSM-5 declines the MTO performance of HZSM-5. For example, Ca54-HZSM-5 with the highest Ca content presented the lowest methanol conversion (77%) at WHSV = 3.3 h?1and 490 °C, whereas other catalysts resulted in the methanol conversion > 93% at the same condition.

    In addition to the impact on the yield of products,it is noteworthy that Ca in the catalyst framework leads to a mitigating effect on the growth of carbon species.After the MTO performance test, the spent Caexchanged catalysts turned into gray color instead of black color for the parent HZSM-5 catalyst.

    According to Table 5, the methanol conversions of catalysts are in the below order at 440 to 490 °C and WHSV ≈ 5.5 h?1:

    HZSM-5 > Ca9-HZSM-5 > Ca27-HZSM-5 >Ca54-HZSM-5

    However, at the lowest temperature, i.e. 390 °C and WHSV ≈ 5.5 h?1, the Ca27-HZSM-5 catalyst was the most active one. It could be attributed to its largest density of the strongest acid sites among Ca substituted catalysts, although these acid sites are weaker than HZSM-5 and the major portion are of Lewis acid type as confirmed by pyridine FT-IR data. The Ca LAS seems to drive MTO reactions with less activation energy.

    Ca27-HZSM-5 ≈ HZSM-5 > Ca9-HZSM-5 >Ca54-HZSM-5

    Steric hindrance of Ca atoms in the Ca27-HZSM-5 zeolite structure with a decreasing effect on conversion, as well as the highest number of accessible Ca LAS (weaker than BAS on HZSM-5) among Ca incorporated zeolites, could lead to the acceptable activity and the high selectivity to light olefins. Ca54-HZSM-5 seems to be overloaded with Ca atoms and their steric hindrance may prevent acid sites to be available for MTO reactions.

    The peak areas of strongest acid sites (3thdesorption peak) in TPD profiles of the prepared catalysts follow the below order:

    Ca27-HZSM-5 > Ca9-HZSM-5 > HZSM-5 ≈ Ca54-HZSM-5

    As it was pointed above, the larger peak areas indicate the larger portion of accessible Ca LAS.

    Based on the temperature of the peaks centerlines in NH3-TPD profiles presented in Table 4, the strength of acid sites corresponding to the 3thdesorption peak of the prepared catalysts follows the below order:

    HZSM-5 (575 °C) > Ca27-HZSM-5, Ca54-HZSM-5 (518 °C) > Ca9-HZSM-5 (468 °C)

    According to the NH3-TPD profiles and the result of MTO performance of the prepared catalysts, two properties of zeolite acidity, i.e. the strength (and their type) and the density of the different types, were used to explain the results. Less density of BAS in zeolites decreases the methanol conversion whereas it enhances the selectivity to light olefins in the MTO conversion.It should be noted that probable transition-state-shapeselectivity induced by Ca cations may also cooperate with the reduced acid strength of Ca LAS to enhance the selectivity of lighter olefins.

    Ca9-HZSM-5 catalyst showed the smaller density of Ca LAS and lower average strength of acid sites than Ca27-HZSM-5. According to pyridine-IR data,BAS only in Ca9-HZSM-5 catalyst was weakened. In agreement, its average strength of acidity (3rdpeak in TPD) was obtained as the lowest among the prepared catalysts. However, it provided more methanol conversion than Ca27-HZSM-5. It may be described by the steric hindrance of higher Ca content of the latter zeolite limiting species transport or product transition state formation in its pore structure. Species with a larger hydrodynamic diameter than ammonia faces more diffusion barrier in the pore structure of Ca27-HZSM-5 than that of Ca9-HZSM-5, leading to the decline of methanol conversion to the MTO products.Another issue is the percentage of BAS in Ca9-HZSM-5 (68%) which is larger than that of Ca27-HZSM-5(22%) as calculated from their pyridine adsorbed IR absorption spectra. Bridged OH Br?nsted acid sites,even with reduced strength in Ca9-HZSM-5, may be more active than Ca associated Lewis acid sites in the zeolites.

    It is noteworthy that the higher content of Ca in Ca54-HZSM-5 zeolite imposes transport limitation on both nitrogen as surface probe and ammonia as the probe of acid sites, leading to less measured surface area and density of acid sites, respectively. Therefore,the lowest density of acid sites is available to methanol in the pore structure of Ca54-HZSM-5 which resulted in the lowest methanol conversion. In addition, the portion of Br?nsted acid sites extensively reduces to 18%.

    The influence of Ca incorporation on the acidic properties of HZSM-5 as the catalyst on MTO product selectivity and its deactivation has been reported in the literature[46? 48,64]. It has been observed that less acidic strength suppresses aromatic cycle in the MTO reaction pathway producing less ethylene and deactivating aromatic species. The weakened acid sites could not further convert olefins produced by methylation/cracking in the alkene cycle into aromatics. Yarulina et al[48]have carefully studied modification of acidity strength of HZSM-5 by Ca incorporation. In summary,the transformation of Br?nsted into Lewis acidity by Ca modification were confirmed and the improved life time and increased selectivity to propylene of Ca modified HZSM-5 was related to the decline of acid strength proved by NH3-TPD data. Reduction of acid sites density was not observed in the NH3-TPD spectra,despite revealing the transformation of Br?nsted into Lewis acidity by pyridine FT-IR. The theoretically calculated OH frequency shift of CaOCaOH+as proposed stable species in Ca-HZSM-5 indicated a weaker Br?nsted acidity[48].

    The area of the third NH3desorption peak in NH3-TPD spectra increased in Ca9-HZSM-5 and Ca27-HZSM-5, and decreased again at the highest Ca content in Ca54-HZSM-5. This decline of peak area may be explained by the possible steric hindrance effect of Ca atoms becoming important after a threshold content. It means Ca incorporation could result in the increase of LAS, however, the associated steric hindrance could inhibit the accessibility of acid sites. Diffusion limitation in Ca2+incorporated HZSM-5 may be caused by its larger size than H+and its substitution location in the pore structure. The covalent radius of Ca (0.173 nm)is more than 5 times of H (0.032 nm). This shows a larger distance of Ca from pore walls than H. Ca preferentially exchanges with H at channel intersections[38], where the acid sites favor aromatic cycle of MTO. However, it begins to exchange at the channels wall at higher content with clearly stronger negative effect on pore diffusion.

    The strength of acid sites was declined by Ca incorporation in Ca9-HZSM-5 and then was enhanced again in Ca27-HZSM-5 and Ca54-HZSM-5 along with the intensified increase of peak areas. The decline in the strength of acid sites and conversion of Br?nsted to Lewis acid sites with Ca incorporation has been observed and explained by other researchers, too[48].However, the reason for the re-increase of strength of acid sites with Ca content could be inferred from pyridine IR data. The strength of BASs in Ca9-HZSM-5 was decreased and strengthened again in Ca27-HZSM-5 and Ca54-HZSM-5. However, the average strength of strong acid sites in the latter catalysts, is still less than those of the parent HZSM-5 due to the dominance portion of LASs. The LAS portion in two latter catalysts are nearly the same. Hence, the center of the third peak, related to the average strength of strong acid sites are the same in two latter catalysts.

    2.7 MTO activity versus time

    With less initial activity of Ca27-HZSM-5 (53%)than HZSM-5 (59%), methanol conversion followed an oscillatory trend over both catalysts with different intensity. This oscillatory trend has also been observed in other similar studies on MTO conversion using Ca modified HZSM-5 in our group[49]. Figure 6 shows that Ca27-HZSM-5 recovers its initial conversion in 24 h after which the second wave appears. During the second wave, the period of rising activity started at time on stream ≈ 70 h and methanol conversion reached to 64% at 99 h, higher than the initial value.The methanol conversion over HZSM-5 was recovered to 58% after about 70 h followed by a decline to 48%in the next 24 h. Considering selectivity of light olefin products with time on stream over both catalysts, it can be noticed that selectivities are more stable than methanol conversion.

    These results determined a more thorough research is required for any conclusion on the long term MTO performance as a result of Ca incorporation to HZSM-5 zeolite. Although catalytic activity of HZSM-5 showed small fluctuations, it presented a more stable MTO activity than Ca27-HZSM-5. Ca27-HZSM-5 lost about 30% of its activity at 70 h,however, it became more active after 100 h. It is required to carry out an activity test of longer duration to determine stability preference. The oscillation of MTO activity of catalysts at the condition of nano size particles of catalysts and high methanol WHSV, may be resulted from the sequential formation and break down of carbonaceous species inside the porous structure of catalysts.

    If the oscillatory feature of MTO activity of Ca27-HZSM-5 continues to longer times on stream, the deactivation could be slowed down as an advantageous feature.

    2.8 Analysis of coked catalyst

    2.8.1 FT-IR results

    FT-IR spectra of coked Ca27-HZSM-5-LT and Ca54-HZSM-5 catalysts were recorded in the range of 400?4000 cm?1, displayed in Figure S6 of the supplementary material file. Ca27-HZSM-5-LT denotes the coked Ca27-HZSM-5 catalyst after long term MTO activity test. The FT-IR bands at 1580 and 1650 cm?1are assigned to stretching mode of aromatic C=C bonds in poly-aromatic hydrocarbons (PAH) or in coke (dienes)[65?67]. The band at 1580 cm?1is not present in the FT-IR spectra of fresh catalysts. The carbon deposits containing PAH are called Coke-II. The band at 2930 cm?1is most likely due to aliphatic ?CH2and?CH groups, and the band at 2960 cm?1to ?CH3aliphatic groups[66]and the band at 3050 cm?1to stretching mode of C?H aromatic bonds[65]. The vibration mode at 1506 and 1414 cm?1corresponds to CH2and CH3bending[65].Weak band at 730 cm?1in the FT-IR spectrum of Ca27-HZSM-5-LT is ascribed to bending vibration of mono and ortho di-substituted methyl aromatic C?H bond.

    The strong band at 1729 cm?1corresponds to the stretching mode of C=O bond, assumed as a sign of formation of oxygenated carbon deposit. It is observed in FT-IR spectra of both coked samples, however, it is intensified in the Ca27-HZSM-5-LT. It can be deduced that the oxygenated coke, Coke-I, is formed at early times on stream and remains on the catalyst for a long period. The C=O band also exists on the FT-IR profile of fresh catalyst each.

    2.8.2 Thermogravimetric results

    TG profiles of the used Ca27-HZSM-5-LT and Ca54-HZSM-5 catalysts, as shown in Figure 7, indicated an intense effect of Ca incorporation on the amount of coke formed in the porous structure of the HZSM-5.The time on stream of methanol for HZSM-5 was ca.5 h, while Ca27-HZSM-5-LT was catalyzing the MTO reaction for about 100 h.

    Figure 7 Thermogravimetric and differential weight loss profiles of (a) the spent Ca27-HZSM-5-LT and(b) Ca54-HZSM-5 catalysts

    According to the TG data, Ca27-HZSM-5-LT showed 6.3% weight loss after 100 h time on stream,whereas Ca54-HZSM-5 contained at least 7.5%carbonaceous deposits after 5 h interval. 2 % of weight loss in Ca27-HZSM-5-LT accounts for moisture dried at ca. 120 °C. Hence, Ca27-HZSM-5 encountered carbonaceous deposits of less than 4.3% which is well below coke content on Ca57-HZSM-5.

    Carbon deposits on Ca54-HZSM-5 experienced a range of combustion temperatures from 420 to 646 °C.The descending end of TG profile of Ca54-HZSM-5 indicated weight loss could be continued over higher temperature than 650 °C.

    First, this carbonaceous precipitate on both of the used catalysts are less than 10% which is an advantageous feature achieved by Ca incorporation,especially at fairly high space velocity used in the study. Another important result is that the amount of coke precipitation remained constant in the long period of reaction over Ca27-HZSM-5-LT as it was less than that of Ca54-HZSM-5 on which MTO reaction carried out for only 5 h. Therefore, the proper content of Ca in HZSM-5 not only mitigates the rate of coke formation but also stands for coke growth over long periods effectively.

    Several bands can be seen in the derivative plot of TG profiles. Bands with maximum temperature less than 200 °C in DTG curve are attributed to adsorbed water and permanent gas molecules. Carbonaceous species over Ca27-HZSM-5-LT burnt at 210 and 581 °C whereas DTG profile of Ca54-HZSM-5 indicated four different species burning at 349 to 646 °C. The higher combustion temperature indicates more condensed,higher graphitization and lower H/C ratio of carbon deposits[66,68]. It means that at the early stage of MTO,coke deposits are formed with different degrees of condensations over Ca54-HZSM-5. After a long time on stream the composition of coke deposits turns into the highest possible molecular weight over Ca27-HZSM-5-LT, i.e. progressively from the intermediate poly-alkylbenzenes to inactive and more condensed polycyclic aromatic structures[68]. In another term,oxygenated coke deposits, such as the species burnt at lower temperatures such as 210 °C over Ca27-HZSM-5 or 350 to 420 °C over Ca54-HZSM-5, called Coke-I,converts with methylation to polycyclic aromatics burnt at 536 to 646 °C, called Coke-II, or the single type coke deposit over Ca27-HZSM-5-LT removed at 581 °C. Coke-I as an oxygenated carbon species burnt at lower temperature deactivates HZSM-5 faster than the Coke-II as a poly aromatic species. It has been previously reported that two kinds of carbonaceous species can be formed inside pores of HZSM-5 in the MTO conversion, deactivating HZSM-5 by site blocking[68]. The conversion process of Coke-I to Coke-II with time on stream has been previously suggested by several research groups[66,68].

    It is believed that MTO reaction is driven by a hydrocarbon pool (HCP) mechanism based on a dual mechanism, Alkene-based route and aromatic-based route[38,69]. In the Alkene-based route heavier olefins are active HCP species, while poly-methyl-benzenes are the active HCP intermediates in the other[38]. MTO on the Ca containing HZSM-5 catalysts has been reported to proceed over the alkene cycle as the dominant route due the steric hindrance effect resulting from Ca ions exchanged with H+[48,38]. Our results indicated the formation of Coke-II which confirms the aromaticbased driving mechanism route is active, too.

    The difference of composition of coke deposits formed over Ca27-HZSM-5-LT and Ca54-HZSM-5 is clear. The Coke-II over Ca54-HZSM-5 removed at about 646 °C is heavier than Ca27-HZSM-5-LT burnt at 581 °C. Hence, Ca content may interrelate with the composition of carbon deposit formed on the HZSM-5 in MTO reaction. Moreover, the amount of carbon deposits could be influenced by Ca incorporation in HZSM-5. Therefore, Ca incorporation can be employed to control both light olefin selectivity and lifetime in MTO conversion.

    3 Conclusions

    The methanol conversion and selectivity to light olefins for the parent and Ca modified HZSM-5 catalysts (9 ≤ Ca/Al ≤ 54) were measured. It was found that there is an optimum Ca content in HZSM-5 to obtain the best MTO performance. Ca27-HZSM-5(Ca/Al = 27) showed the best catalytic performance with the yields of ethylene and propylene equal to 0.11 and 0.14 at 490 °C, respectively. Ca incorporation in HZSM-5 significantly decreased coke formation as calculated through TG analysis and deduced from the intensity of color change after reaction. Overloading of Ca in HZSM-5 led to formation of inaccessible LAS.

    Ca modification of HZSM-5 improved the yield of ethylene and propylene and led to independency of yield of light olefins on temperature. It implies the decrease of energy barrier of MTO on Ca incorporated ZSM-5 in the studied range of temperature.

    The performance of the evaluated catalysts in the MTO reaction were explained through deconvoluted FT-IR and NH3-TPD profiles based on the BAS/LAS ratio, steric hindrance and strength of acid sites. Ca27-HZSM-5 contained the largest number of accessible LAS. BAS include 78% of total acid sites in Ca27-HZSM-5. The effect of Ca content of HZSM-5 on the wavenumber of BAS vibration band, meaning their strength variation, was observed in FT-IR spectra of pyridine adsorbed zeolites. Ca incorporation weakens BAS at a threshold after which BAS strength is recovered again.

    The catalyst stability experiment indicated that both oxygenated and polyaromatic carbon deposits were formed over the Ca incorporated HZSM-5 catalysts. Proper Ca content may lead to the formation of lighter aromatic carbon deposits.

    The long-term MTO activity test showed an intense oscillatory behavior over Ca27-HZSM-5-LT and the higher activity than initial value after about 100 h.

    Acknowledgement

    Financial support of South Pars Gas Complex(S.P.G.C), Vice-Presidency of Research and Technology is gratefully acknowledged.

    99久久精品热视频| 1024手机看黄色片| 色尼玛亚洲综合影院| 午夜视频国产福利| ponron亚洲| 亚洲自偷自拍三级| 嫩草影院入口| 国产亚洲av片在线观看秒播厂 | 亚洲精品影视一区二区三区av| 欧美3d第一页| 欧美激情国产日韩精品一区| av天堂在线播放| 亚洲av免费在线观看| 精品久久久久久久末码| 亚洲国产精品国产精品| 国产精品一区二区在线观看99 | 婷婷亚洲欧美| av免费观看日本| 嫩草影院精品99| 可以在线观看的亚洲视频| 亚洲在线自拍视频| 麻豆久久精品国产亚洲av| 国产精品国产三级国产av玫瑰| 18禁在线无遮挡免费观看视频| 91精品国产九色| 中国美白少妇内射xxxbb| 在线观看av片永久免费下载| 久久久久久国产a免费观看| 老司机影院成人| 日本一本二区三区精品| 小说图片视频综合网站| 黑人高潮一二区| 日韩高清综合在线| 老师上课跳d突然被开到最大视频| 黄色日韩在线| 亚洲av免费在线观看| 18禁裸乳无遮挡免费网站照片| 日本三级黄在线观看| 国产精品一区二区三区四区免费观看| 男女做爰动态图高潮gif福利片| 最近中文字幕高清免费大全6| 美女高潮的动态| 亚洲国产日韩欧美精品在线观看| 国产午夜精品久久久久久一区二区三区| 国产国拍精品亚洲av在线观看| 国产亚洲精品久久久com| 国产精品蜜桃在线观看 | 国产三级中文精品| 少妇丰满av| 国产精品三级大全| 麻豆乱淫一区二区| 国产探花极品一区二区| 国产高清激情床上av| 免费人成视频x8x8入口观看| 欧美极品一区二区三区四区| 欧美不卡视频在线免费观看| 国产精品国产三级国产av玫瑰| 午夜免费激情av| 老女人水多毛片| 美女脱内裤让男人舔精品视频 | 欧美极品一区二区三区四区| 国产高清不卡午夜福利| 亚洲熟妇中文字幕五十中出| 久久精品国产亚洲网站| 久久鲁丝午夜福利片| 久久国产乱子免费精品| 久久午夜福利片| 国产精品永久免费网站| 国内精品美女久久久久久| 国产精品一区二区三区四区久久| 日韩 亚洲 欧美在线| 国产在线男女| 91av网一区二区| 两个人视频免费观看高清| 特大巨黑吊av在线直播| 亚洲中文字幕日韩| 久久久久久久午夜电影| 免费看av在线观看网站| 成年版毛片免费区| 国产一区亚洲一区在线观看| 亚洲欧美日韩高清专用| 久久亚洲国产成人精品v| 亚洲精品日韩在线中文字幕 | 看十八女毛片水多多多| 日韩三级伦理在线观看| 国产中年淑女户外野战色| 欧美变态另类bdsm刘玥| 黄片wwwwww| 色播亚洲综合网| 校园春色视频在线观看| av.在线天堂| 国产成年人精品一区二区| 日韩亚洲欧美综合| 亚洲精华国产精华液的使用体验 | 日韩av不卡免费在线播放| 亚洲av成人av| 久久精品久久久久久久性| 欧美激情国产日韩精品一区| 久久精品国产清高在天天线| 熟女人妻精品中文字幕| 麻豆成人av视频| 精品久久久久久久久亚洲| 亚洲aⅴ乱码一区二区在线播放| 亚洲不卡免费看| 国产老妇女一区| 日韩三级伦理在线观看| 国产日本99.免费观看| 一个人看视频在线观看www免费| av国产免费在线观看| 色播亚洲综合网| av黄色大香蕉| 久久欧美精品欧美久久欧美| 日本爱情动作片www.在线观看| 女人被狂操c到高潮| 黄色配什么色好看| 国产一区亚洲一区在线观看| 久久精品久久久久久久性| 黄色配什么色好看| 国产精品人妻久久久影院| 亚洲国产色片| 日韩成人伦理影院| 国产蜜桃级精品一区二区三区| 午夜福利视频1000在线观看| 日韩一区二区视频免费看| 久久久午夜欧美精品| 校园人妻丝袜中文字幕| 精品久久久噜噜| 91久久精品电影网| 99九九线精品视频在线观看视频| av黄色大香蕉| 国产亚洲5aaaaa淫片| 最近中文字幕高清免费大全6| 亚洲不卡免费看| 天堂中文最新版在线下载 | av黄色大香蕉| 日产精品乱码卡一卡2卡三| 国产黄色小视频在线观看| 高清毛片免费看| 夜夜看夜夜爽夜夜摸| 99在线人妻在线中文字幕| 国产中年淑女户外野战色| 成人高潮视频无遮挡免费网站| 九九久久精品国产亚洲av麻豆| 免费观看的影片在线观看| 国产激情偷乱视频一区二区| 色噜噜av男人的天堂激情| 国产成人影院久久av| 欧美潮喷喷水| 一区福利在线观看| 久久精品夜色国产| 女同久久另类99精品国产91| 亚洲国产欧美人成| 久久精品国产亚洲av天美| 国产极品精品免费视频能看的| 久久久久久大精品| 国产av一区在线观看免费| 99久久久亚洲精品蜜臀av| 美女xxoo啪啪120秒动态图| 亚洲av不卡在线观看| 在线观看免费视频日本深夜| 嫩草影院精品99| 精品久久久久久成人av| 日韩一本色道免费dvd| 一个人免费在线观看电影| 亚洲国产精品国产精品| 日本与韩国留学比较| 国产精品久久久久久av不卡| 免费观看精品视频网站| 久久精品国产自在天天线| 男插女下体视频免费在线播放| 99久久精品一区二区三区| 哪个播放器可以免费观看大片| 午夜福利在线观看吧| 大又大粗又爽又黄少妇毛片口| av在线观看视频网站免费| 亚洲婷婷狠狠爱综合网| 国产亚洲精品av在线| 亚洲欧美成人综合另类久久久 | 99久久精品一区二区三区| av免费观看日本| 国产精华一区二区三区| 欧美+日韩+精品| 日日撸夜夜添| 免费看av在线观看网站| 一区二区三区高清视频在线| av视频在线观看入口| 观看免费一级毛片| 18禁黄网站禁片免费观看直播| 一本久久精品| 久久久久国产网址| 欧美性猛交黑人性爽| 成年av动漫网址| 我的老师免费观看完整版| 亚洲av一区综合| 中文在线观看免费www的网站| 国产精品久久久久久亚洲av鲁大| 亚洲欧美清纯卡通| 不卡视频在线观看欧美| 男女边吃奶边做爰视频| 又爽又黄a免费视频| 久久精品人妻少妇| 久久久久九九精品影院| 免费av观看视频| 国产伦精品一区二区三区视频9| 亚洲成人久久爱视频| 久久久久国产网址| a级毛片免费高清观看在线播放| 午夜精品国产一区二区电影 | 亚洲精品国产av成人精品| 中文资源天堂在线| 亚洲av成人av| 中文字幕人妻熟人妻熟丝袜美| 久久欧美精品欧美久久欧美| 日本欧美国产在线视频| 亚洲av二区三区四区| 久久精品综合一区二区三区| 国产综合懂色| 国产一区二区在线观看日韩| 青春草国产在线视频 | 日韩av在线大香蕉| 亚洲无线观看免费| 国产高清视频在线观看网站| 中出人妻视频一区二区| 悠悠久久av| 天美传媒精品一区二区| 波多野结衣巨乳人妻| 亚洲欧美成人综合另类久久久 | 日日摸夜夜添夜夜添av毛片| 色综合亚洲欧美另类图片| 热99re8久久精品国产| 欧美日韩综合久久久久久| 我要看日韩黄色一级片| 中文字幕久久专区| 免费电影在线观看免费观看| 晚上一个人看的免费电影| 国产免费一级a男人的天堂| 岛国在线免费视频观看| 亚洲国产日韩欧美精品在线观看| 有码 亚洲区| 久久久久久久久久久丰满| 久久久午夜欧美精品| 高清毛片免费观看视频网站| 亚洲经典国产精华液单| 99久久无色码亚洲精品果冻| 国产午夜精品论理片| 深夜精品福利| 午夜久久久久精精品| 亚洲欧美精品专区久久| 在线免费观看不下载黄p国产| 九九在线视频观看精品| 嫩草影院入口| 黄色配什么色好看| 欧美日韩乱码在线| 看黄色毛片网站| 美女国产视频在线观看| 亚洲av不卡在线观看| 中文字幕av成人在线电影| 一边摸一边抽搐一进一小说| 久久久久久久久久久免费av| 嫩草影院新地址| 国产伦精品一区二区三区四那| 国产伦精品一区二区三区视频9| 欧美色视频一区免费| h日本视频在线播放| 国产一区二区三区在线臀色熟女| 国产伦精品一区二区三区四那| 丰满的人妻完整版| 嘟嘟电影网在线观看| ponron亚洲| 性色avwww在线观看| 伊人久久精品亚洲午夜| 亚洲国产欧美人成| 99精品在免费线老司机午夜| 免费av毛片视频| 一级av片app| 国内少妇人妻偷人精品xxx网站| 国产成人影院久久av| 久久久久国产网址| 嫩草影院新地址| 亚洲人成网站在线观看播放| 国产一区二区在线av高清观看| 国产大屁股一区二区在线视频| 亚洲真实伦在线观看| 亚洲国产色片| 国产免费一级a男人的天堂| 国产精品久久视频播放| 国产毛片a区久久久久| 黄色视频,在线免费观看| 99热精品在线国产| 丰满人妻一区二区三区视频av| 欧美极品一区二区三区四区| 亚洲精品成人久久久久久| 韩国av在线不卡| 成人毛片60女人毛片免费| 好男人视频免费观看在线| 国产探花极品一区二区| 日韩成人av中文字幕在线观看| 久久这里有精品视频免费| 免费电影在线观看免费观看| 中文在线观看免费www的网站| 色噜噜av男人的天堂激情| 夜夜夜夜夜久久久久| 国产高潮美女av| 亚洲va在线va天堂va国产| 国产精品国产高清国产av| 久久综合国产亚洲精品| 国产午夜精品论理片| 成人特级av手机在线观看| 成人美女网站在线观看视频| 免费不卡的大黄色大毛片视频在线观看 | 亚洲内射少妇av| 老师上课跳d突然被开到最大视频| 国产不卡一卡二| 国产69精品久久久久777片| 亚洲激情五月婷婷啪啪| 美女 人体艺术 gogo| 永久网站在线| 久久国内精品自在自线图片| 天堂中文最新版在线下载 | 欧美不卡视频在线免费观看| 91久久精品国产一区二区成人| 国产精品99久久久久久久久| 超碰av人人做人人爽久久| 18+在线观看网站| 有码 亚洲区| 亚洲欧美日韩高清在线视频| 亚洲国产欧美在线一区| 国产 一区 欧美 日韩| 久久精品夜夜夜夜夜久久蜜豆| 一级av片app| 2021天堂中文幕一二区在线观| 国产成人aa在线观看| 精品一区二区三区人妻视频| 好男人在线观看高清免费视频| 全区人妻精品视频| 国产亚洲精品久久久com| 九九在线视频观看精品| 春色校园在线视频观看| av.在线天堂| 一本久久精品| 午夜福利在线观看免费完整高清在 | 在线国产一区二区在线| 最近视频中文字幕2019在线8| 亚洲丝袜综合中文字幕| 久久精品综合一区二区三区| 日韩欧美在线乱码| 最近视频中文字幕2019在线8| 国产午夜精品一二区理论片| 欧美性猛交黑人性爽| 久久这里有精品视频免费| 九色成人免费人妻av| 国产日韩欧美在线精品| 亚洲熟妇中文字幕五十中出| 成人欧美大片| 综合色av麻豆| 中文资源天堂在线| 嫩草影院新地址| 国产探花极品一区二区| 日日摸夜夜添夜夜爱| 亚洲国产精品合色在线| 亚洲高清免费不卡视频| 美女脱内裤让男人舔精品视频 | 九草在线视频观看| 少妇猛男粗大的猛烈进出视频 | 国产精品久久久久久精品电影小说 | 村上凉子中文字幕在线| 非洲黑人性xxxx精品又粗又长| 欧美+亚洲+日韩+国产| 欧美xxxx性猛交bbbb| ponron亚洲| 乱系列少妇在线播放| 成人毛片a级毛片在线播放| 亚洲国产精品成人久久小说 | 国产v大片淫在线免费观看| 亚洲欧美日韩无卡精品| 校园春色视频在线观看| 亚洲综合色惰| 国产成人精品一,二区 | 国产成人freesex在线| 亚洲av一区综合| 国产探花极品一区二区| 少妇猛男粗大的猛烈进出视频 | 人妻少妇偷人精品九色| 男人舔奶头视频| 精品无人区乱码1区二区| 午夜福利在线在线| 亚洲精品456在线播放app| 精品人妻视频免费看| 又爽又黄无遮挡网站| 精品人妻视频免费看| 国产精品蜜桃在线观看 | 日本黄色片子视频| 欧美日韩精品成人综合77777| 午夜精品国产一区二区电影 | 免费看日本二区| 欧美日韩精品成人综合77777| 一卡2卡三卡四卡精品乱码亚洲| 午夜a级毛片| 直男gayav资源| 菩萨蛮人人尽说江南好唐韦庄 | 在线国产一区二区在线| 午夜亚洲福利在线播放| 一个人看的www免费观看视频| 欧美xxxx黑人xx丫x性爽| 中文亚洲av片在线观看爽| 给我免费播放毛片高清在线观看| 久久热精品热| 三级毛片av免费| 亚洲真实伦在线观看| 国产单亲对白刺激| 亚洲欧洲国产日韩| 久久久a久久爽久久v久久| 国产精品人妻久久久影院| 国产探花在线观看一区二区| 久久韩国三级中文字幕| 欧美最新免费一区二区三区| 综合色丁香网| 免费一级毛片在线播放高清视频| 九九久久精品国产亚洲av麻豆| 热99re8久久精品国产| h日本视频在线播放| 乱人视频在线观看| 99久久成人亚洲精品观看| 久久国产乱子免费精品| 啦啦啦啦在线视频资源| 日韩中字成人| 天堂影院成人在线观看| 99在线人妻在线中文字幕| 中文字幕av在线有码专区| 乱人视频在线观看| 欧美不卡视频在线免费观看| 国产亚洲av嫩草精品影院| 亚洲成人久久性| 美女 人体艺术 gogo| 亚洲自拍偷在线| 99热这里只有精品一区| 亚洲自偷自拍三级| 黄色欧美视频在线观看| 听说在线观看完整版免费高清| 国产精品乱码一区二三区的特点| 久久午夜福利片| 国产成人精品久久久久久| 熟女人妻精品中文字幕| 久久国产乱子免费精品| 午夜久久久久精精品| АⅤ资源中文在线天堂| 亚洲无线观看免费| 六月丁香七月| 12—13女人毛片做爰片一| 国产日本99.免费观看| 精品久久久久久久久亚洲| 高清在线视频一区二区三区 | 国产精品女同一区二区软件| 少妇高潮的动态图| 一本一本综合久久| 2021天堂中文幕一二区在线观| 国产成人精品久久久久久| 麻豆国产av国片精品| 日产精品乱码卡一卡2卡三| 老司机福利观看| 色吧在线观看| 午夜免费男女啪啪视频观看| 久久6这里有精品| 99视频精品全部免费 在线| 1024手机看黄色片| 中文欧美无线码| 亚洲图色成人| 国产男人的电影天堂91| 欧美日韩国产亚洲二区| 精品久久久久久久末码| 国内少妇人妻偷人精品xxx网站| 成人鲁丝片一二三区免费| 婷婷六月久久综合丁香| 啦啦啦观看免费观看视频高清| 乱人视频在线观看| 久久鲁丝午夜福利片| 亚洲va在线va天堂va国产| 久久热精品热| 午夜精品国产一区二区电影 | 直男gayav资源| 国产av不卡久久| 亚洲,欧美,日韩| 欧美xxxx黑人xx丫x性爽| 91久久精品电影网| 特大巨黑吊av在线直播| 亚洲自偷自拍三级| 伦精品一区二区三区| 亚洲高清免费不卡视频| 天天躁夜夜躁狠狠久久av| 极品教师在线视频| 国产成年人精品一区二区| 国产精品不卡视频一区二区| 中国美女看黄片| 国产精品综合久久久久久久免费| 久久草成人影院| 在线免费观看的www视频| 中文字幕av在线有码专区| 亚洲aⅴ乱码一区二区在线播放| 国产一级毛片七仙女欲春2| 国产精品一二三区在线看| 国内揄拍国产精品人妻在线| 成人欧美大片| 91久久精品国产一区二区成人| 身体一侧抽搐| 国产精品伦人一区二区| 深夜精品福利| 久久精品国产亚洲av涩爱 | 神马国产精品三级电影在线观看| 欧美极品一区二区三区四区| 亚洲内射少妇av| 少妇熟女aⅴ在线视频| 男插女下体视频免费在线播放| 日产精品乱码卡一卡2卡三| 直男gayav资源| 国国产精品蜜臀av免费| 99久久九九国产精品国产免费| 久久久色成人| 精品久久久久久久久亚洲| 黄色欧美视频在线观看| 亚洲七黄色美女视频| 国内精品美女久久久久久| 久久精品国产99精品国产亚洲性色| 亚洲av男天堂| 亚洲精华国产精华液的使用体验 | 在线观看av片永久免费下载| 内地一区二区视频在线| 久久久久久久午夜电影| 免费av不卡在线播放| 最近的中文字幕免费完整| 五月伊人婷婷丁香| 精品国内亚洲2022精品成人| 亚洲av熟女| 91久久精品电影网| 免费黄网站久久成人精品| 国产一区二区激情短视频| 国产精品.久久久| 麻豆成人午夜福利视频| 男人舔女人下体高潮全视频| 99久久精品一区二区三区| 男女视频在线观看网站免费| 午夜福利高清视频| 别揉我奶头 嗯啊视频| 亚洲国产欧美人成| .国产精品久久| 在线免费观看不下载黄p国产| 九九久久精品国产亚洲av麻豆| 看黄色毛片网站| 一边摸一边抽搐一进一小说| 人人妻人人澡欧美一区二区| 十八禁国产超污无遮挡网站| 搡老妇女老女人老熟妇| 亚洲一区二区三区色噜噜| 晚上一个人看的免费电影| 久久精品影院6| 99久久九九国产精品国产免费| 可以在线观看的亚洲视频| 久久这里只有精品中国| 国产成人午夜福利电影在线观看| 午夜老司机福利剧场| 久久99蜜桃精品久久| 真实男女啪啪啪动态图| 天美传媒精品一区二区| 边亲边吃奶的免费视频| 成年av动漫网址| 久久久久久大精品| 九九在线视频观看精品| 久久精品国产99精品国产亚洲性色| 欧美精品国产亚洲| 欧美+日韩+精品| 精品一区二区三区视频在线| 国产高清激情床上av| 97超碰精品成人国产| 最后的刺客免费高清国语| 亚洲成人精品中文字幕电影| 黄色欧美视频在线观看| 91久久精品国产一区二区成人| 亚洲精品自拍成人| 精品人妻一区二区三区麻豆| 国产一区二区三区在线臀色熟女| 久久精品91蜜桃| 成人亚洲精品av一区二区| 国国产精品蜜臀av免费| 亚洲人成网站在线播放欧美日韩| 一级av片app| 精品久久国产蜜桃| 欧美日韩综合久久久久久| 国产单亲对白刺激| 国产一区二区在线av高清观看| 欧美最新免费一区二区三区| 亚洲一区高清亚洲精品| 国产精品一区二区三区四区久久| 国产精品.久久久| 日韩一区二区三区影片| 国产精品人妻久久久影院| 色综合色国产| 免费在线观看成人毛片| 免费av毛片视频| 精品少妇黑人巨大在线播放 | 国产成人午夜福利电影在线观看| 美女cb高潮喷水在线观看| 少妇被粗大猛烈的视频| 午夜视频国产福利| 日本一二三区视频观看| 男人舔女人下体高潮全视频| 国产精品不卡视频一区二区| 精品欧美国产一区二区三| 在线观看一区二区三区| kizo精华| 国产片特级美女逼逼视频| 精品一区二区免费观看| 两性午夜刺激爽爽歪歪视频在线观看| 麻豆成人午夜福利视频| 亚洲av男天堂| 欧美激情久久久久久爽电影| 美女 人体艺术 gogo|