• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Experimental study on ceramic balls impact composite armor

    2020-05-23 07:09:24WeizhnWngZhigngChenShunshnFengTiyongZho
    Defence Technology 2020年2期

    Wei-zhn Wng , Zhi-gng Chen , Shun-shn Feng , Ti-yong Zho

    a Underground Target Damage Technology National Defense Key Discipline Laboratory, North University of China, Taiyuan 030051, Shanxi, China

    b State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology,100081, Beijing, China

    Keywords:Impact Penetration Infinitesimal Interface collapse

    ABSTRACT Ceramic balls represent a new type of damaging element, and studies on their damaging power of composite armor are required for a comprehensive evaluation of the effectiveness of various types of weapons.The goal of this study was to determine the impact of φ7 mm toughened Al2O3 ceramic balls on a composite ceramic/metal armor. The influences of the ceramic panel and the thickness of the metal backing material on the destroying power of the ceramic balls were first determined. Based on the agreement between numerical simulation, experimental results, and calculation models of the target plate resistance,the response mechanism of the ceramic balls was further analyzed.The results indicate that for a back plate of Q235 steel,with an increasing thickness of the ceramic panel,the piercing speed limit of the ceramic balls gradually increases and the diameter of the out-going hole on the metal back decreases. Different conditions were tested to assess the effects on the piercing speed, the diameter of the out-going hole, the micro-element stress, and the integrity of the recovered ceramic bowl.

    1. Introduction

    In modern warfare, with the rapid development of warhead technology, lightweight composite armor with strategic value has attracted much attention. The new warhead damage element represented by high-performance and low-cost ceramic balls has emerged as the times require. Compared with ordinary tungsten alloy and steel fragments,ceramic balls have the advantages of high strength, large specific kinetic energy, low-cost and easy production,etc.They can effectively strike at close range armored targets,and the study of damage effect of ceramic balls on armored targets is an important part of weapon system effectiveness evaluation.

    In recent years, scholars at home and abroad have made some reports on the damage power and dynamic properties of ceramic damage elements.Nechitatio[1,2]and others have used numerical simulation methods to study the fracture of a ceramic rod impacting metal target, and compared the fracture morphology of the target under different impact velocities.Then Nechitatio carried out in the experimental study of penetrating concrete target with head-mounted polycrystalline diamond penetration projectile at different impact velocities based on the numerical simulation method. Takahashi [3] studied the fracture characteristics of ceramic balls under high pressure by means of an experimental study,theoretical analysis and numerical simulation.Matsuda[4,5]analyzed the fracture characteristics of ceramic balls under thermal shock, established the calculation theory of virtual crack model,and carried out the indentation contrast test on silicon nitride ceramic balls between air and vacuum.Ma[6]used fractal theory to analyze the fracture characteristics of brittle spheres under high velocity impact. The theoretical analysis results are in good agreement with the experimental results.Wang[7-15]pointed out that ceramic balls have the advantages of high strength, high specific kinetic energy and high initial velocity, and have high penetrating efficiency and high aftereffect of close range targets (pine targets, aluminum plates, etc.). Chen [16-25] proposed replacing conventional metal warheads with non-metal ceramic warheads,and found that ceramic composite projectiles can effectively improve the damage power of composite armor.

    At present, the damage mechanism and armor-piercing response characteristics of the damage elements of ceramic materials have been preliminaries understood through the research on the damage effectiveness of the damage elements of ceramic materials, but the damage law of light composite armor and the response law of the damage elements of ceramic materials are rarely studied. Based on the ballistic impact test, the influence of ceramic balls on the ultimate penetration velocity and impact breakage threshold of ceramic composite armor under different working conditions is studied in this paper.Based on the numerical simulation and impact pressure calculation theory, the interface breakdown effect of ceramic balls is predicted and analyzed, and the response characteristics of ceramic balls and composite armor are expounded.

    2. Experiment preparation

    2.1. Laboratory equipment

    The experiment was conducted out at the target road of the National Defense Key Discipline Laboratory of Underground Target Damage Technology of the North University of China. The test composite back plate uses a Q235 steel target of 500 mm×500 mm×2 mm in size and a 2024 aluminum target.The ceramic panel includes Al2O3ceramic panels with dimensions of 100 mm×100 mm×1 mm, 100 mm×100 mm×2 mm, and 100 mm×100 mm×3 mm. The middle layer is bonded with glass fibers. In view of the that the loading size of the 7.62 mm ballistic gun to the ceramic ball diameter is less than 7.2 mm and the loading speed is less than 1500 m/s,the penetration power(specific kinetic energy) of the ceramic ball is proportional to the radiusRand the loading speedv,respectively,i.e.a 7.62 mm ballistic gun.There is a loading limit on the size and penetration power of the ceramic ball.In addition, considering that the wavelength of the stress wave of the ceramic ball material is 5.2 mm or less,to explore the breaking law of the ceramic ball effectively it is necessary to ensure that the size of the ceramic ball is at least larger than the wavelength of the ceramic material. A tensile wave and a compression wave were utilized to analyze the breaking law of the ceramic ball. To penetrate the target plate comprehensively and effectively explore the breaking law of the ceramic ball, the fragment is made of a toughened Al2O3ceramic bowl with a size of φ7 mm. The test equipment is shown in Fig.1.

    2.2. Ballistic tests

    In this study, several effective toughened Al2O3ceramic ball impacting composite target panels was tested. A 7.62 mm caliber ballistic guns were used for testing, and the launch speed was adjusted by modifying the loading of the gunpowder. A laser speedometer is independently developed by the North University of China was used for the speed measurement, within an error of±0.3%.A schematic diagram of the(a)test arrangement and(b)site layout is shown in Fig.2.

    Fig.1. Laboratory equipment.

    3. Numerical simulation

    3.1. Model establishments

    A finite element model was built using TRUEGRID software. To reduce the computation time, a three-dimensional finite element model was established based on a 1/2 structure, and symmetric constraints were set on the symmetry plane of the 1/2 model.The ceramic ball and ceramic panel were modeled using the SPH smooth particle algorithm, and the contact between the ball and panel was modeled using a particle-particle contact algorithm.The numerical simulation of the bonding layer utilized the solid joint between the ceramic panel/metal backplane interface.The normal failure force and shear failure force between the finite elements of the particle and the metal back plate were taken as 21 N and 12 N,respectively [25]. Fig. 3 shows the finite element mesh model applied.

    3.2. Parameter selections

    In this example, the MAT_JOHNSON_HOLMQUIST_CERAMICS material model was used to describe the toughened Al2O3ceramic ball and Al2O3ceramic panel.The Q235 steel back target and 2024 aluminum back target material model were based on the Johnson-Cook material model and the Gruneisen equation of state. To toughen the AL2O3, the ceramic material parameters listed in Table 1 and other material parameters from the literature[16-24]were used in the dynamics software Autodyn to reproduce the process of a ceramic ball impacting a composite armor.

    4. Analysis of the results

    4.1. Analysis of the response characteristics of ceramic balls

    When a ceramic ball impacts a composite target, different influences are imparted on the response characteristics of the ceramic bowl by the thicknesses of the metal back plate material and ceramic plate. Table 2 shows the test results of the impacting and crushing velocity thresholds for some ceramic balls,and Fig.4 shows the relationship between the impacting and crushing velocity thresholds of ceramic balls and the thicknesses of the ceramic plates.Fig.5(a)-(c)present the change curve in the stress applied to the micro units of ceramic balls under two operating conditions.

    Fig. 2. Schematic diagram of (a) test arrangement and (b) site layout.

    Fig. 3. Finite element mesh model.

    As shown in Fig.4,the impacting and breaking threshold of the ceramic balls decreased as the thickness of the ceramic panel increased, where as the impacting and crushing thresholds of ceramic balls on the ceramic plates of the same thickness were less under working condition 1 than those under working condition 2.This is because,compared with the Q235 steel back plate,the 2024 aluminum back plate can deform more readily under the smashing and plugging effect of the ceramic balls and ceramic cones [26];hence, reducing the reaction of the composite ceramic ball to the target surface.At the same impact velocity,the force applied on the micro units of a ceramic ball was smaller than under condition 1(see Fig.5(a)),resulting in increased thresholds for the impact and crushing of the ceramic balls. Under the same impact velocity, the force applied on the micro units of ceramic balls under the two working conditions increased with an increase in the thickness of the ceramic panel (see Fig. 5 (b)). The increase in the thickness of the ceramic panel increased the opportunity to form a ceramic cone. Under the same impact velocity, the force applied on the micro units of a ceramic ball continues to increase(see Fig.5(c)),as does the extension rate of the fracture inside the ceramic ball,causing the ball to break more easily.

    As a ceramic ball hits the target plate at a higher speed.A zone of extremely high pressure is formed at the impact point within a rather wide pressure range in which no impact phase changes are present.According to the momentum conservation law at the time of impact and the continuity condition at the interface,the pressure at the hitting point can be expressed by the following formula[27]:

    Fig. 4. Relationship between ceramic plate thickness and impact fracture threshold.

    According to Newton's third law,

    Table 1 Ceramic material parameters.

    Table 2 Impact test results of impact crushing speed of some ceramic balls.

    Fig. 5. (a) Relationship between ceramic ball micro-element stress σ and t of h=3 mm, (b) Relationship between ceramic ball micro-element stress σ and ceramic

    Fig.6. Relationship between unit density ρc of composite target plate and thickness h of ceramic panel.

    The real velocity on the impact interface is as follows:

    WherePPanduPare the impact pressure and particle velocity acting on the projectile;Pcanducare the impact pressure and particle velocity acting on the ceramic panel;andaPand[fx]andacandbcare the Hugoniot material parameters of the ceramic ball and the ceramic panel and RHA, respectively [16-23], wherevPis the velocity of the ceramic ball, and ρPis the density.

    Considering the heterogeneity of the structures, the backplate materials of the composite armor,and the concept of the composite target surface density,the unit body density in the composite target thickness direction is introduced, namely,

    where ρccis the surface density of the composite target andhc is the unit thickness of the composite target,the value of which is 1.

    By using Eqs. (1)-(5), the impact pressure acting on the projectile when the ceramic ball impacts the ceramic composite target can be solved.Fig.6 shows the relationship between the composite target plate body density and the thickness of the ceramic panel h,and Fig.7 shows the relationship between the force applied on the micro units of the ceramic ball and the thickness of the ceramic panel under two working conditions for an impact velocity of 700 m/s.It can be seen from Fig.6 that the unit body density in the composite target thickness direction increases with an increase in the ceramic panel thickness.The theoretical calculation of the force applied on the micro units (see Fig. 7) and the rules of the numerical simulation (see Fig. 5 (b)) show good consistency.

    panel thickness(h) atv=700 m/s, (c) Relationship between the stress σ and t of the ceramic ball micro-element under condition 2.

    Fig. 7. Relationship between ceramic ball micro-element stress σ and ceramic panel thickness h.

    Under the two working conditions,for the ceramic panels with different thicknesses, the impact energy distribution of a ceramic ball changes under the support of the elastoplastic back plate and the impact property changes.Fig.8(a)and 8(b)present the crushed pattern of the recovered ceramic ball under the condition of limiting piercing. Fig. 8 (c) and 8(d) display the numerically simulated damage cloud diagram of a ceramic ball for the same limit penetration velocity. Fig. 9 shows the relationship between the thickness of the ceramic plate and the residual mass of the ceramic ball for a limited penetration velocity. Fig. 10 presents the relationship between the force applied on the micro units of the ceramic bowl and the thickness of the ceramic panel at the limit penetration velocity.

    As can be seen from Fig.8(a)-(b),with an increased thickness of the ceramic panel, the quantity of recovered ceramic bowl fragments gradually reduces and the integrity significantly declines.The fracture cross-section passes through the axis of the impact velocity direction on the ceramic ball. Further, the integrity of the ceramic ball is better under working condition 2 than under working condition 1, because the limit penetration velocity under working condition 1 is greater than that under working condition 2 for the same ceramic panel thicknesses. The pressing and tensile stresses applied to the micro units of the ceramic balls is larger(see Fig.10),with obvious fractures and breakages.From Fig.8(c)-(d),it can be seen that, when increasing the limit of the penetration velocity (see Fig. 12), the fracturing location on the ceramic ball changes, extending from an axial to a radial fracture, with an increase in the fracture area. A comparison of the ceramic ball fractures under the two types of working conditions revealed that the extent of crushing on the ceramic ball under working condition 1 is greater than that under working condition 2,for the same ceramic panel thicknesses. Moreover, its remaining mass is less than that under working condition 2 (see Fig. 9). Comparisons of the numerical simulation results and the experimental phenomena reveal that the two are highly consistent.

    Fig.9. Relationship between ceramic plate thickness h and residual mass m of ceramic ball is under ballistic limit.

    Fig.10. Relationship between ceramic panel thickness h and micro-element stress σ.

    Based on the good consistency demonstrated between the numerical simulation and the experimental results, a further numerical simulation of the fracture characteristics of a ceramic ball during a high-speed impact on the composite target plate was carried out. Fig. 11 shows a cloud diagram of the smashing and damage occurring on the interface of ceramic ball under different impact velocities under working conditions 1 and 2.

    As can be seen from Fig.11(a)and 11(b),with an increase in the impact velocity,a more obvious breakage of the ceramic ball occurs,which remains on the side of the positive impact surface. The ability to penetrate the metal back plate became increasingly weaker, with changes in the damaged drums occurring along the direction of the valvular dehiscence, and perforation appearing on the metal back plate.The angle between splashing direction of the fragments of the ceramic panel and ceramic ball and the impact velocity direction increased, gradually changing into transverse splashing. Under a high-speed impact, there is an increased force applied on the ceramic bowl and the fracturing phenomenon becomes even more noticeable. In addition, the kinetic energy is distributed into smaller ceramic fragments causing an increased impact area on the target plate, with most of the kinetic energy consumed by the fracturing of the ceramic panel,the ceramic ball,and the deformation of the metal back plate. The overall piercing power declines, weakening the penetrating ability of the metal back plate.There is increased smashing[28,29]and damage to the interface,without the ability to pierce the metal backboard.This is more obvious for working condition 1 than for working condition 2.Owing the higher backing plate strength under working condition 1 than that under working condition 2.This causes the ceramic ball to be more stressed(see Fig.10), which is made more fragile.

    4.2. Analysis of composite armor damage characteristics

    Multiple φ7 mm toughened Al2O3ceramic balls were studied for an impact of a composite armor. Some limit penetration velocity test data were obtained and are presented in Table 3 below.Fig.12 shows the relationship between the ceramic panel thickness (h)and the limit penetration velocity (v).

    Fig.11. Damaged cloud image of ceramic ball interface under high-speed impact.

    Fig.12. Relationship between ceramic panel thickness and h-limit penetration velocity v.

    It can be seen from Fig.12 that under the two working conditions, with an increase in the thickness of the ceramic panel, the limit penetration velocity gradually increases.The limit penetration velocity and the increasing rate under condition 1 were greater than those under condition 2. Under the same conditions of the back plate, with an increase in thickness of the ceramic formed cone, more kinetic energy of the ceramic ball is consumed. When the speed of the ceramic ball is higher, the greater the impact pressure on the micro units[30]and the more likely that a crushing will occur (see Figs. 10 and 11). The increase in kinetic energy consumption is not conducive to the influence behavior. For the same ceramic panel thicknesses,when the ceramic balls impact the composite target plate at the constant speed, the ceramic cone forming sizes is almost the same [26], with the same area being affected on the metal backplane. Because the impact strength of a Q235 steel back plate is greater than that of a 2024 aluminum back plate, under the same kinetic energy conditions, the ceramic ball can more easily pierce the ceramic/aluminum composite target plate. This is identical with the experiment results and the published rules for a theoretical model calculation [31].

    The damaging characteristics of the ceramic composite targetsunder different impact velocities can differ to a certain extent.Understanding damaging characteristics of the ceramic composite targets will provide guidance for their design. Fig. 13 shows the relationship between the thickness of the ceramic panel and the diameter of the penetrated hole on the back panel. Figs.14 and 15 show the test results and numerical simulation results for a piercing of the composite ceramic target plate under the two working conditions.

    Table 3 Test results.

    Fig.14 shows that,under working condition 1,when the ceramic panel thickness is 1 mm,the damage on the metal back plate shows a punching and plugging pattern(see Fig.14(a),whereh=1 mm).When the ceramic panel thickness is 2 or 3 mm, the penetrated hole on the Q235 steel metal back plate shows valvular dehiscence and perforation (see Fig.14 (a), whereh=2,h=3 mm, and Fig.14(b)), with identical numerical simulation results. With an increased thickness of the ceramic panel, the broken area around the edge of the penetrated hole on the ceramic panel decreases gradually, and the cracks extend circumferentially from the aperture. Under working condition 2, with an increased thickness of the ceramic panel,the convoluted pattern of the penetrated hole on the 2024 aluminum back plate gradually becomes obvious,transition from a punched and plugged penetrated hole pattern to a ductile penetrated hole pattern,with a good matching between the penetrated hole patterns and the numerical simulation results(see Fig.15).

    Fig.13. Relationship between the thickness h of the ceramic plate and diameter r of the back plate at the ultimate penetration speed.

    From the results presented in Figs.14 and 15,it can also be seen that as the thickness of the ceramic plate increases, a decrease in the diameter of the penetrated hole gradually occurs,which is not obvious. This is because the ceramic plate is locally fractured and broken after being impacted, and the hole diameter formed by joining the ceramic fragments is incomplete. As the ceramic plate increases in thickness,the overall resistance of the ceramic plate to the shear strength increases, and the compaction effect of the ceramic bowl on the formed ceramic cone decreases until the ceramic ball can no longer pierce the ceramic panel. Hole piercing on the metal back plate mainly occurs by the ceramic core and some of the ceramic bowl fragments; hence, the penetrated hole diameter on the ceramic panel decreases.Considering the results of Fig.13, if the thicknesses of the ceramic panels are the same, the penetrated hole diameter on the back plate under working condition 1 was less than that under working condition 2, and the decreasing rate of the penetrated hole diameter was greater than that for working condition 2. This indicates that the support strength of the Q235 steel back plate is greater than that of the 2024 aluminum back plate, which causes the force applied to the micro units of a ceramic ball to greatly increase (see Fig. 5 (a)-(c)). The quantity of the ceramic fragments decreases during the impact process. But because their volumes are relatively small given the penetrated hole diameter on the metal back plate(see Fig.13).

    5. Conclusion

    Based on ballistic impact test results, a numerical simulation and a theoretical analysis were used to study the impact of ceramic balls on composite target plates, and the following conclusions were obtained:

    Fig.14. Comparison of test results and numerical simulation results under working condition 1.

    Fig.15. Comparison of test and numerical simulation results under working condition 2.

    1. Increasing the thickness of a ceramic panel and the strength of the metal back plate will lead to an increase in the stress applied to the micro units of a ceramic ball, and the fracturing of the ceramic ball will be more serious under the same impact velocity.For a ceramic panel 3 mm thick and a metal back plate of Q235 steel, the threshold values of the impact and crushing speed of the ceramic ball are at a minimum.With an increase in the impact speed, smashing and damage to the interface are more likely to occur, and there is a decreased chance that the ceramic ball will pierce the metal back plate.

    2. When the ceramic panel thickness and strength of the metal back plate are increased, the limit penetration velocity of the ceramic ball increases and its integrity decreases. The holepiercing mode on the ceramic ball changes from overall holepiercing into hole piercing of the local fragments, which causes a change in the hole-piercing pattern on the metal back plate from a punched and plugged penetrated hole pattern to a valvular dehiscing/ductile penetrated hole pattern, with the penetrated hole diameter gradually decreasing in size.

    3. Comparing and analyzing the numerical simulation results with the experiment and theoretical calculation results, good consistency was shown, indicating that the numerical simulation method adopted in this paper is reliable (to a certain extent).

    欧美最新免费一区二区三区| av线在线观看网站| 日韩av免费高清视频| 桃花免费在线播放| 久久精品久久久久久噜噜老黄| 黑丝袜美女国产一区| 秋霞伦理黄片| 日韩电影二区| 亚洲国产毛片av蜜桃av| 精品人妻一区二区三区麻豆| 国产精品99久久99久久久不卡 | 日本欧美视频一区| 久久久国产欧美日韩av| videos熟女内射| 99久久人妻综合| 高清在线视频一区二区三区| 建设人人有责人人尽责人人享有的| 国产1区2区3区精品| 一二三四中文在线观看免费高清| 青青草视频在线视频观看| 国产精品三级大全| 十分钟在线观看高清视频www| 成人手机av| 日本色播在线视频| 国产熟女欧美一区二区| 90打野战视频偷拍视频| 中文字幕另类日韩欧美亚洲嫩草| 亚洲国产日韩一区二区| 欧美激情极品国产一区二区三区 | 亚洲伊人久久精品综合| 伊人亚洲综合成人网| 免费观看av网站的网址| 寂寞人妻少妇视频99o| 色5月婷婷丁香| 久久久欧美国产精品| 国产日韩欧美在线精品| 91成人精品电影| 国产日韩欧美亚洲二区| 国产色爽女视频免费观看| tube8黄色片| 亚洲欧美一区二区三区国产| 日日爽夜夜爽网站| 91精品国产国语对白视频| 国产免费视频播放在线视频| 美女内射精品一级片tv| 黄片播放在线免费| 丝袜美足系列| 美国免费a级毛片| 国产在视频线精品| 成年人午夜在线观看视频| 精品一区二区三区视频在线| 看免费av毛片| 国产成人a∨麻豆精品| xxxhd国产人妻xxx| 欧美日韩视频高清一区二区三区二| 最近最新中文字幕免费大全7| 午夜福利网站1000一区二区三区| 久久精品久久久久久久性| 9191精品国产免费久久| 精品一区二区三区四区五区乱码 | 国产精品一区二区在线不卡| 黄片播放在线免费| 亚洲精品国产色婷婷电影| 亚洲伊人久久精品综合| 少妇人妻久久综合中文| 亚洲综合色惰| 婷婷色麻豆天堂久久| 一级,二级,三级黄色视频| 男女边吃奶边做爰视频| 日韩视频在线欧美| 国产精品麻豆人妻色哟哟久久| 18禁观看日本| 成年av动漫网址| 国产成人av激情在线播放| 一区二区三区四区激情视频| 高清不卡的av网站| 99九九在线精品视频| 大片免费播放器 马上看| 啦啦啦视频在线资源免费观看| 国产激情久久老熟女| 中文字幕最新亚洲高清| 精品第一国产精品| 久久韩国三级中文字幕| 在线观看美女被高潮喷水网站| 久久久久视频综合| 久久精品久久久久久噜噜老黄| 亚洲av中文av极速乱| 免费观看在线日韩| 亚洲精品美女久久av网站| 精品酒店卫生间| 五月开心婷婷网| 永久网站在线| 日韩熟女老妇一区二区性免费视频| 久久精品熟女亚洲av麻豆精品| 国产色爽女视频免费观看| 国产一区有黄有色的免费视频| 久久精品国产鲁丝片午夜精品| 久久久久久人妻| 乱码一卡2卡4卡精品| 久久久久久人妻| 国产亚洲av片在线观看秒播厂| 午夜精品国产一区二区电影| 国产在线一区二区三区精| 国产日韩欧美在线精品| 考比视频在线观看| 亚洲精品美女久久久久99蜜臀 | 国产免费又黄又爽又色| 男人添女人高潮全过程视频| 宅男免费午夜| 亚洲中文av在线| 黄色一级大片看看| 91精品三级在线观看| 日韩熟女老妇一区二区性免费视频| 看十八女毛片水多多多| 欧美+日韩+精品| 亚洲精华国产精华液的使用体验| 久久精品aⅴ一区二区三区四区 | 亚洲国产精品成人久久小说| 久久久久精品性色| a级毛色黄片| 热re99久久精品国产66热6| 国产在线一区二区三区精| 亚洲精品久久成人aⅴ小说| 午夜视频国产福利| 极品少妇高潮喷水抽搐| 精品视频人人做人人爽| 欧美老熟妇乱子伦牲交| 大香蕉久久网| 亚洲国产精品一区二区三区在线| 最近最新中文字幕大全免费视频 | 国产成人欧美| 精品99又大又爽又粗少妇毛片| 亚洲少妇的诱惑av| 日韩一区二区视频免费看| 男人添女人高潮全过程视频| 少妇被粗大的猛进出69影院 | 波野结衣二区三区在线| 久久鲁丝午夜福利片| 99国产精品免费福利视频| 熟女电影av网| 91国产中文字幕| 亚洲av男天堂| 777米奇影视久久| 在线观看国产h片| 大片免费播放器 马上看| 美女国产高潮福利片在线看| 中文字幕亚洲精品专区| 在线观看人妻少妇| 精品人妻在线不人妻| 五月开心婷婷网| 精品福利永久在线观看| 欧美日韩成人在线一区二区| 亚洲伊人久久精品综合| 亚洲精品国产色婷婷电影| 午夜91福利影院| 韩国高清视频一区二区三区| 自线自在国产av| 美女中出高潮动态图| 亚洲,欧美,日韩| 亚洲,欧美精品.| 尾随美女入室| 日韩成人伦理影院| 18禁国产床啪视频网站| 久久久久久久国产电影| 国产在线一区二区三区精| 秋霞伦理黄片| 国产成人精品在线电影| 91午夜精品亚洲一区二区三区| 亚洲精品,欧美精品| 汤姆久久久久久久影院中文字幕| 国产精品无大码| 一级毛片 在线播放| 黄色怎么调成土黄色| 亚洲欧美中文字幕日韩二区| 一级黄片播放器| 性色av一级| 免费黄频网站在线观看国产| 99国产精品免费福利视频| 纵有疾风起免费观看全集完整版| 一区二区三区精品91| 18禁裸乳无遮挡动漫免费视频| 精品一区在线观看国产| 国产亚洲最大av| 亚洲精品日本国产第一区| 久久久久久人人人人人| 久久这里有精品视频免费| 精品国产一区二区三区久久久樱花| 精品熟女少妇av免费看| 国产永久视频网站| 桃花免费在线播放| 亚洲国产最新在线播放| 久久人人97超碰香蕉20202| 大香蕉久久网| 91午夜精品亚洲一区二区三区| av片东京热男人的天堂| 王馨瑶露胸无遮挡在线观看| 久久久久久人人人人人| 久久精品国产亚洲av涩爱| 久久99蜜桃精品久久| 久久影院123| 狂野欧美激情性bbbbbb| 欧美成人午夜免费资源| 蜜桃在线观看..| 制服丝袜香蕉在线| 最黄视频免费看| 久久ye,这里只有精品| 亚洲四区av| 在线观看www视频免费| 亚洲精品一二三| 成人毛片a级毛片在线播放| 免费观看a级毛片全部| 男女高潮啪啪啪动态图| 日日摸夜夜添夜夜爱| 久久精品夜色国产| 日日啪夜夜爽| 精品酒店卫生间| 看非洲黑人一级黄片| 伦理电影免费视频| 免费日韩欧美在线观看| 精品亚洲成a人片在线观看| 十八禁网站网址无遮挡| 永久免费av网站大全| 少妇人妻久久综合中文| 校园人妻丝袜中文字幕| 在现免费观看毛片| 国产成人欧美| 80岁老熟妇乱子伦牲交| 全区人妻精品视频| 少妇人妻 视频| 免费观看性生交大片5| 一级黄片播放器| 国产日韩欧美亚洲二区| av有码第一页| 大香蕉久久成人网| 成人18禁高潮啪啪吃奶动态图| 卡戴珊不雅视频在线播放| 亚洲欧美日韩另类电影网站| 男女无遮挡免费网站观看| 国产精品久久久久久久电影| 最黄视频免费看| 黄色怎么调成土黄色| 国产69精品久久久久777片| 国产免费又黄又爽又色| 日本免费在线观看一区| 久久久久精品久久久久真实原创| 日韩中文字幕视频在线看片| 亚洲精品av麻豆狂野| 99热这里只有是精品在线观看| 国产乱人偷精品视频| 亚洲人成网站在线观看播放| 国产熟女欧美一区二区| 最黄视频免费看| 精品少妇久久久久久888优播| 在现免费观看毛片| 久久久久久人妻| 久久久国产精品麻豆| 亚洲色图 男人天堂 中文字幕 | xxxhd国产人妻xxx| 欧美精品亚洲一区二区| 国产色婷婷99| 99精国产麻豆久久婷婷| 亚洲av.av天堂| 一区二区三区四区激情视频| 久久久久久人人人人人| 高清视频免费观看一区二区| 1024视频免费在线观看| 国产激情久久老熟女| 亚洲综合精品二区| 久久精品国产鲁丝片午夜精品| 久热这里只有精品99| 亚洲av日韩在线播放| 在线观看三级黄色| 婷婷色综合www| av黄色大香蕉| 最近中文字幕2019免费版| 日本av免费视频播放| av天堂久久9| 热re99久久精品国产66热6| 18禁国产床啪视频网站| 亚洲av国产av综合av卡| 国产片内射在线| 一边摸一边做爽爽视频免费| 青春草视频在线免费观看| 最后的刺客免费高清国语| 中文乱码字字幕精品一区二区三区| 女人被躁到高潮嗷嗷叫费观| 91精品三级在线观看| 欧美精品一区二区免费开放| 久久综合国产亚洲精品| 亚洲欧美中文字幕日韩二区| 97在线人人人人妻| 欧美日韩一区二区视频在线观看视频在线| 免费播放大片免费观看视频在线观看| 亚洲av福利一区| 高清欧美精品videossex| 亚洲欧美色中文字幕在线| 男女免费视频国产| 精品一区二区三区四区五区乱码 | 边亲边吃奶的免费视频| 国产亚洲欧美精品永久| 在现免费观看毛片| 国产日韩欧美亚洲二区| 永久网站在线| 大码成人一级视频| av女优亚洲男人天堂| 极品少妇高潮喷水抽搐| 欧美最新免费一区二区三区| 亚洲色图 男人天堂 中文字幕 | 久久人人爽人人片av| 巨乳人妻的诱惑在线观看| 在线天堂最新版资源| 免费播放大片免费观看视频在线观看| 久久青草综合色| 亚洲成人一二三区av| 国产一区二区三区综合在线观看 | 精品一区二区三区视频在线| 一级爰片在线观看| 在线看a的网站| 一级片'在线观看视频| 51国产日韩欧美| 人妻 亚洲 视频| 国产永久视频网站| 欧美精品av麻豆av| 久久99热6这里只有精品| 亚洲人成网站在线观看播放| 日韩av在线免费看完整版不卡| 黑人猛操日本美女一级片| 婷婷成人精品国产| 国产白丝娇喘喷水9色精品| 搡女人真爽免费视频火全软件| 国产1区2区3区精品| 一个人免费看片子| 日韩av在线免费看完整版不卡| 国产精品欧美亚洲77777| 国产一级毛片在线| 大陆偷拍与自拍| 国产一区亚洲一区在线观看| videossex国产| 久久99热6这里只有精品| 97超碰精品成人国产| 国产极品天堂在线| 9色porny在线观看| 亚洲国产精品国产精品| 久久女婷五月综合色啪小说| 精品久久国产蜜桃| 国产日韩欧美视频二区| 91精品三级在线观看| 亚洲综合色惰| av电影中文网址| 精品人妻在线不人妻| 国产精品一国产av| 男男h啪啪无遮挡| 欧美精品高潮呻吟av久久| 精品福利永久在线观看| 精品第一国产精品| 婷婷成人精品国产| 国产成人一区二区在线| 久久99蜜桃精品久久| 精品少妇内射三级| 麻豆乱淫一区二区| 9热在线视频观看99| 日日爽夜夜爽网站| 色哟哟·www| 狠狠婷婷综合久久久久久88av| 亚洲欧美色中文字幕在线| 女人久久www免费人成看片| 亚洲精品日韩在线中文字幕| 久久人人爽av亚洲精品天堂| 大香蕉97超碰在线| 51国产日韩欧美| 久久久a久久爽久久v久久| 你懂的网址亚洲精品在线观看| 五月玫瑰六月丁香| a级毛色黄片| 久久久久久久久久久免费av| 国产欧美另类精品又又久久亚洲欧美| 9热在线视频观看99| 日本黄色日本黄色录像| 最近最新中文字幕免费大全7| 久久精品夜色国产| 久久久久国产网址| 久久久久久伊人网av| 国产亚洲精品久久久com| 国产一区二区激情短视频 | 免费在线观看完整版高清| 国产欧美日韩综合在线一区二区| 91精品伊人久久大香线蕉| 国产亚洲av片在线观看秒播厂| 久久久国产精品麻豆| 色哟哟·www| 丰满饥渴人妻一区二区三| 免费观看在线日韩| 午夜久久久在线观看| 免费黄网站久久成人精品| 美女脱内裤让男人舔精品视频| 大片电影免费在线观看免费| 女性被躁到高潮视频| 99re6热这里在线精品视频| 欧美日韩综合久久久久久| 国产精品无大码| 丝袜美足系列| 一个人免费看片子| 国产黄频视频在线观看| av一本久久久久| 中文字幕制服av| 欧美日韩一区二区视频在线观看视频在线| 亚洲综合色网址| 久久人人爽人人片av| 大香蕉久久成人网| 免费久久久久久久精品成人欧美视频 | 满18在线观看网站| 中国国产av一级| 亚洲精品456在线播放app| 亚洲成av片中文字幕在线观看 | 卡戴珊不雅视频在线播放| 在线观看人妻少妇| 国产精品偷伦视频观看了| 又黄又粗又硬又大视频| 亚洲在久久综合| 久久久国产一区二区| 亚洲国产欧美日韩在线播放| 亚洲av欧美aⅴ国产| 好男人视频免费观看在线| 国产淫语在线视频| 少妇被粗大猛烈的视频| 亚洲国产精品一区三区| 成人二区视频| 少妇被粗大的猛进出69影院 | 精品久久久久久电影网| 欧美精品亚洲一区二区| 欧美激情国产日韩精品一区| 日日撸夜夜添| 观看美女的网站| 精品人妻一区二区三区麻豆| 制服丝袜香蕉在线| 午夜福利视频精品| 九九爱精品视频在线观看| 国产精品久久久av美女十八| 中文天堂在线官网| 啦啦啦中文免费视频观看日本| 亚洲精品国产av蜜桃| 国产精品.久久久| 色吧在线观看| 欧美精品亚洲一区二区| av有码第一页| 两个人看的免费小视频| 天天躁夜夜躁狠狠躁躁| 女性生殖器流出的白浆| 国产 一区精品| 日韩中文字幕视频在线看片| 国产精品一二三区在线看| 精品人妻熟女毛片av久久网站| 午夜福利网站1000一区二区三区| 免费av中文字幕在线| 成人无遮挡网站| 精品亚洲成国产av| 伊人亚洲综合成人网| av电影中文网址| 国产毛片在线视频| 精品午夜福利在线看| 777米奇影视久久| 在线亚洲精品国产二区图片欧美| 最近最新中文字幕大全免费视频 | 成人国产av品久久久| 国产免费一级a男人的天堂| 日韩大片免费观看网站| 欧美3d第一页| www.av在线官网国产| 欧美人与性动交α欧美精品济南到 | 亚洲欧美中文字幕日韩二区| 十八禁高潮呻吟视频| 伊人亚洲综合成人网| 在线看a的网站| 中文字幕亚洲精品专区| 黄色一级大片看看| 汤姆久久久久久久影院中文字幕| 国产日韩一区二区三区精品不卡| 日韩 亚洲 欧美在线| 精品酒店卫生间| 一本—道久久a久久精品蜜桃钙片| 九色亚洲精品在线播放| 亚洲中文av在线| 成人漫画全彩无遮挡| 自线自在国产av| 美女脱内裤让男人舔精品视频| 18禁裸乳无遮挡动漫免费视频| 男人爽女人下面视频在线观看| 免费在线观看完整版高清| 亚洲精品久久久久久婷婷小说| 男女国产视频网站| 妹子高潮喷水视频| 女性生殖器流出的白浆| 国产亚洲最大av| 亚洲五月色婷婷综合| 精品人妻在线不人妻| 久久这里只有精品19| 亚洲欧美中文字幕日韩二区| 伊人久久国产一区二区| 国产精品偷伦视频观看了| 亚洲婷婷狠狠爱综合网| 成年动漫av网址| 男人操女人黄网站| 最近的中文字幕免费完整| 亚洲性久久影院| 亚洲欧美成人综合另类久久久| 国产免费一区二区三区四区乱码| 在线观看人妻少妇| 日韩伦理黄色片| 色婷婷久久久亚洲欧美| 久久久国产精品麻豆| 久久久久精品人妻al黑| 在线观看国产h片| 国产日韩欧美在线精品| 极品人妻少妇av视频| 超碰97精品在线观看| 亚洲精品日韩在线中文字幕| 午夜福利视频精品| 两个人免费观看高清视频| 欧美精品一区二区免费开放| 99热这里只有是精品在线观看| 久久女婷五月综合色啪小说| 一级a做视频免费观看| 麻豆精品久久久久久蜜桃| 免费av不卡在线播放| 丰满乱子伦码专区| 国产色爽女视频免费观看| 久久99蜜桃精品久久| 我要看黄色一级片免费的| 国产探花极品一区二区| 中文天堂在线官网| 久久ye,这里只有精品| 国产精品久久久av美女十八| 国产精品无大码| 熟女人妻精品中文字幕| 亚洲av欧美aⅴ国产| 曰老女人黄片| 制服丝袜香蕉在线| 99久久精品国产国产毛片| 精品少妇黑人巨大在线播放| 国国产精品蜜臀av免费| 国产高清三级在线| 亚洲国产av新网站| 日韩 亚洲 欧美在线| 国产熟女欧美一区二区| 男女国产视频网站| 成年动漫av网址| 色婷婷av一区二区三区视频| 自线自在国产av| 日本午夜av视频| 国产成人欧美| av福利片在线| a级毛色黄片| 伊人亚洲综合成人网| 一区二区三区乱码不卡18| 90打野战视频偷拍视频| 精品少妇内射三级| 亚洲成av片中文字幕在线观看 | 飞空精品影院首页| 亚洲美女黄色视频免费看| av卡一久久| 久久久久精品人妻al黑| 又粗又硬又长又爽又黄的视频| 女人被躁到高潮嗷嗷叫费观| 如日韩欧美国产精品一区二区三区| 亚洲高清免费不卡视频| 深夜精品福利| 激情五月婷婷亚洲| 九九爱精品视频在线观看| 国产精品一国产av| 久久国内精品自在自线图片| 考比视频在线观看| 日韩av免费高清视频| av黄色大香蕉| 国产一区亚洲一区在线观看| 久久久久久久大尺度免费视频| 这个男人来自地球电影免费观看 | 精品99又大又爽又粗少妇毛片| 国产有黄有色有爽视频| 亚洲色图综合在线观看| 99国产精品免费福利视频| 国产精品三级大全| 女人被躁到高潮嗷嗷叫费观| 久久精品国产自在天天线| 亚洲成人一二三区av| 丝袜人妻中文字幕| 一边摸一边做爽爽视频免费| 91午夜精品亚洲一区二区三区| 中文字幕精品免费在线观看视频 | 日本午夜av视频| 狠狠精品人妻久久久久久综合| 国产免费一级a男人的天堂| 丰满少妇做爰视频| 性高湖久久久久久久久免费观看| 搡老乐熟女国产| 美女中出高潮动态图| 成人手机av| 香蕉精品网在线| 日本av免费视频播放| 如何舔出高潮| 大话2 男鬼变身卡| 国产 精品1| 永久免费av网站大全| 国产精品一区www在线观看| 18+在线观看网站| 免费在线观看黄色视频的| 丝袜在线中文字幕| 五月伊人婷婷丁香| 麻豆乱淫一区二区| 免费女性裸体啪啪无遮挡网站| 亚洲美女视频黄频| 亚洲,一卡二卡三卡| 女性生殖器流出的白浆| 亚洲欧美日韩卡通动漫| 欧美激情 高清一区二区三区| 亚洲熟女精品中文字幕|